Einhell Classic TC-CD 18-2 LI User manual

TC-CD 18-2 Li

Art.-Nr.: 45.138.46 I.-Nr.: 11016

1

D Originalbetriebsanleitung

Akku-Bohrschrauber

GB Original operating instructions

Cordless drill/screwdriver

F Instructions d’origine

Perceuse sans ﬁ l

I Istruzioni per l’uso originali

Trapano avvitatore a batteria

DK/ Original betjeningsvejledning

N Akku-bore-/skruemaskine

S Original-bruksanvisning

Batteridriven

borrmaskin/skruvdragare

HR/ Originalne upute za uporabu

BIH Akumulatorska bušilica-izvijač

RS Originalna uputstva za upotrebu

Akumulatorska bušilica-izvijač

CZ Originální návod k obsluze

Akumulátorový vrtací šroubovák

SK Originálny návod na obsluhu

Akumulátorový vŕtací skrutkovač

Anl_TC_CD_18_2_Li_SPK1.indb 1Anl_TC_CD_18_2_Li_SPK1.indb 1 05.09.2016 14:13:0005.09.2016 14:13:00

Page is loading ...

GB

- 14 -

Danger! - Read the operating instructions to reduce the risk of inquiry

Caution! Wear ear-muﬀ s. The impact of noise can cause damage to hearing.

Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted

by the device can cause loss of sight.

Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on

wood and other materials. Never use the device to work on any materials containing asbestos!

Change the gear only when the drill is at a standstill. If you fail to observe this point, the gearing may be

damaged.

Store the battery only in dry rooms with an ambient temperature of +10°C to +40°C. Place only charged

batteries in storage (charged at least 40%).

For use in dry rooms only.

Safety class II

Anl_TC_CD_18_2_Li_SPK1.indb 14Anl_TC_CD_18_2_Li_SPK1.indb 14 05.09.2016 14:13:0805.09.2016 14:13:08

GB

- 15 -

Danger!

When using the equipment, a few safety pre-

cautions must be observed to avoid injuries and

damage. Please read the complete operating

instructions and safety regulations with due care.

Keep this manual in a safe place, so that the in-

formation is available at all times. If you give the

equipment to any other person, hand over these

operating instructions and safety regulations as

well. We cannot accept any liability for damage

or accidents which arise due to a failure to follow

these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be

found in the enclosed booklet.

Danger!

Read all safety regulations and instructions.

Any errors made in following the safety regula-

tions and instructions may result in an electric

shock, ﬁ re and/or serious injury.

Keep all safety regulations and instructions

in a safe place for future use.

2. Layout and items supplied

2.1 Layout (Fig. 1)

1. Torque selector

2. Battery capacity indicator

3. Changeover switch

4. ON/OFF switch

5. Battery pack

6. Battery charger

7. Selector switch for 1st/2nd gear

8. Pushlock button

9. Quick-change drill chuck

10. LED lamp

2.2 Items supplied

Please check that the article is complete as

speciﬁ ed in the scope of delivery. If parts are

missing, please contact our service center or the

sales outlet where you made your purchase at

the latest within 5 working days after purchasing

the product and upon presentation of a valid bill

of purchase. Also, refer to the warranty table in

the service information at the end of the operating

instructions.

•

Open the packaging and take out the equip-

ment with care.

•

Remove the packaging material and any

packaging and/or transportation braces (if

available).

•

Check to see if all items are supplied.

•

Inspect the equipment and accessories for

transport damage.

•

If possible, please keep the packaging until

the end of the guarantee period.

Important!

The equipment and packaging material are

not toys. Do not let children play with plastic

bags, foils or small parts. There is a danger of

swallowing or suﬀ ocating!

•

Cordless drill/screwdriver

•

Battery charger

•

Battery

•

Original operating instructions

•

Safety instructions

3. Proper use

The cordless drill/screwdriver is designed for tigh-

tening and undoing screws, as well as for drilling

in wood, metal and plastic.

The equipment is to be used only for its prescri-

bed purpose. Any other use is deemed to be a

case of misuse. The user / operator and not the

manufacturer will be liable for any damage or inju-

ries of any kind caused as a result of this.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial

applications. Our warranty will be voided if the

machine is used in commercial, trade or industrial

businesses or for equivalent purposes.

Anl_TC_CD_18_2_Li_SPK1.indb 15Anl_TC_CD_18_2_Li_SPK1.indb 15 05.09.2016 14:13:0905.09.2016 14:13:09

GB

- 16 -

4. Technical data

Voltage supply ........................................18 V d.c.

Idling speed: ............................0-350/0-1250 rpm

Torque settings: ........................................... 18+1

Forward and reverse rotation ..........................yes

Chuck clamping width .......................max. 10 mm

Battery charger output voltage: ............. 23 V d. c.

Battery charger output current: .................... 0,5 A

Mains voltage for charger ...100-240 V ~ 50/60 Hz

Battery type: .......................................Lithium-ion

Number of battery cells: .................................... 5

Battery capacitance: .................................1.5 Ah

Weight.........................................................1.6 kg

Max. screw diameter: .................................. 6 mm

The maximum screw diameter indicates the ma-

ximum diameter of the screw that can be screwed

into wood. The screw diameter can vary depen-

ding on the type of wood.

Sound and vibration

Sound and vibration values were measured in

accordance with EN 60745.

L

pA

sound pressure level ................... 70,88 dB(A)

K

pA

uncertainty ............................................. 3 dB

L

WA

sound power level ..................... 81,88 dB(A)

K

WA

uncertainty .............................................3 dB

Wear ear-muﬀ s.

The impact of noise can cause damage to hea-

ring.

Total vibration values (vector sum of three direc-

tions) determined in accordance with EN 60745.

Drilling in metal

Vibration emission value a

h

≤ 2.5 m/s

2

K uncertainty = 1.5 m/s

2

Screwing without hammer action

Vibration emission value a

h

≤ 2.5 m/s

2

K uncertainty = 1.5 m/s

2

The speciﬁ ed vibration value was established in

accordance with a standardized testing method. It

may change according to how the electric equip-

ment is used and may exceed the speciﬁ ed value

in exceptional circumstances.

The speciﬁ ed vibration value can be used to

compare the equipment with other electric power

tools.

The speciﬁ ed vibration value can be used for initi-

al assessment of a harmful eﬀ ect.

Keep the noise emissions and vibrations to a

minimum.

•

Only use appliances which are in perfect wor-

king order.

•

Service and clean the appliance regularly.

•

Adapt your working style to suit the appliance.

•

Do not overload the appliance.

•

Have the appliance serviced whenever ne-

cessary.

•

Switch the appliance off when it is not in use.

•

Wear protective gloves.

Caution!

Residual risks

Even if you use this electric power tool in

accordance with instructions, certain resi-

dual risks cannot be rules out. The following

hazards may arise in connection with the

equipment’s construction and layout:

1. Lung damage if no suitable protective dust

mask is used.

2. Damage to hearing if no suitable ear protec-

tion is used.

3. Health damage caused by hand-arm vib-

rations if the equipment is used over a pro-

longed period or is not properly guided and

maintained.

Limit the operating time.

All stages of the operating cycle must be conside-

red (for example, times in which the electric tools

are switched oﬀ and times in which the tool is

switched on but operates without load).

Anl_TC_CD_18_2_Li_SPK1.indb 16Anl_TC_CD_18_2_Li_SPK1.indb 16 05.09.2016 14:13:0905.09.2016 14:13:09

GB

- 17 -

5. Before starting the equipment

Be sure to read the following information before

you use your cordless screwdriver for the ﬁ rst

time:

1. Charge the battery pack with the charger

supplied. An empty battery pack requires a

charging period of approximately 3 to 5 hours.

2. Only ever use sharp drill bits and screwdriver

bits which are suitable for the purpose and in

faultless condition.

3. Always check for concealed electric cables

and gas and water pipes when drilling and

screwing in walls.

6. Operation

6.1 Charging the Li battery pack (Fig. 2-3)

1. Remove the battery pack (5) from the handle,

pressing the pushlock button (8) downwards

to do so.

2. Check that your mains voltage is the same as

that marked on the rating plate.

3. Plug the battery charger (6) into the power

socket and connect the charging cable (a) to

the battery (5). The three LEDs on the battery

capacity indicator (2) indicate that the battery

is being charged.

- Battery empty: All three LEDs ﬂ ash alterna-

tely

- 1/3 charged: The LED on the left lights up

and the LEDs in the middle and on the right

ﬂ ash alternately

- 2/3 charged: The LEDs on the left and in

the middle light up and the LED on the right

ﬂ ashes

4. When charging is ﬁ nished after approx. 3-5

hours, all three LEDs light up for approx. 10

minutes. Remove the charger from the batte-

ry.

5. If all three LEDs ﬂ ash at the same time, the

battery temperature is either too low or too

high. Remove the charger from the battery,

keep the battery at room temperature for a

day and try again.

6. If the fault is still indicated, the battery is

defective. Do not use or charge a defective

battery. Remove the charger from the battery.

If the battery pack fails to become charged, ple-

ase check

•

whether there is voltage at the socket-outlet

•

whether there is proper contact at the char-

ging contacts on the charger.

If the battery still fails to become charged, please

return

•

the charger

•

the battery pack

to our Customer Service Department.

To ensure that the LI battery pack provides

long service you should take care to recharge

it promptly. You must recharge the battery pack

when you notice that the power of the cordless

screwdriver drops.

6.2 Torque setting (Fig. 4 / Item 1)

Important! The tool must be at a standstill

when you set the torque with the setting ring.

The cordless screwdriver is ﬁ tted with a mechani-

cal torque selector.

The torque for a speciﬁ c size of screw is selected

with the set-collar (1). The correct torque depends

on several factors:

•

on the type and hardness of material in ques-

tion

•

on the type and length screws used

•

on the requirements needing to be met by the

screwed joint.

The clutch disengages with a grating sound to

indicate when the set torque is reached.

6.3 Drilling (Fig. 4 / Item 1)

For drilling purposes, move the set-collar to the

last step „Drill“. In this setting the slip clutch is in-

active. The maximum torque is available in drilling

mode.

6.4 Forward/Reverse switch (Fig. 5 / Item 3)

With the slide switch above the On/Oﬀ switch you

can select the direction of rotation of the battery-

powered drill/screwdriver and secure it against

being switched on accidentally. You can choose

between clockwise and anticlockwise rotation. To

avoid causing damage to the gearing it is advisa-

ble to change the direction of rotation only when

the tool is at a standstill. The On/Oﬀ switch is blo-

cked when the slide switch is in centre position.

6.5 On/Oﬀ switch (Fig. 5 / Item 4)

Inﬁ nitely variable speed control is possible with

the On/Oﬀ switch. The further you press the

switch, the higher the speed of the battery-powe-

red drill/screwdriver.

Anl_TC_CD_18_2_Li_SPK1.indb 17Anl_TC_CD_18_2_Li_SPK1.indb 17 05.09.2016 14:13:0905.09.2016 14:13:09

GB

- 18 -

6.6 Changing over from 1st gear to 2nd gear

(Fig. 4 / Item 7)

You can work at a higher or lower speed depen-

ding on the position of the selector switch. To avo-

id damaging the gear unit you should only change

over gears when the tool has stopped.

6.7 Battery capacity indicator (Fig. 1 – Item 2)

Press the battery capacity indicator switch (a).

The battery capacity indicator (2) shows the char-

ge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED blinks:

The battery is empty, recharge the battery.

All LEDs blink:

The battery temperature is too high. Remove the

battery from the device and keep the battery at

room temperature for a day. If the fault occurs

again, the battery has undergone exhaustive

discharge and is defective. Remove the battery

from the device. Do not use or charge a defective

battery.

6.8 LED lamp (Fig. 1 / Item 10)

The LED lamp (10) can be used in poor lighting

conditions to illuminate the area where you want

to drill or screw. The LED lamp (10) will be lit

automatically as soon as you press the ON/OFF

switch (4).

6.9 Changing the tool (Fig. 6)

Important. Set the changeover switch (3) to its

centre position whenever you carry out any work

(for example changing the tool, maintenance

work, etc.) on the cordless screwdriver.

•

The cordless screwdriver is fitted with a

quick-action chuck (9) with an automatic

spindle stop.

•

Open the chuck (9). The chuck opening (a)

must be large enough to hold the tool (drill bit

or screwdriver bit).

•

Select the suitable tool. Push the tool as far

as possible into the chuck opening (a).

•

Tighten the chuck (9) and then check that the

tool is secure.

6.10 Screwdriving

We recommend using self-centering screws (e.g.

Torx screws, recessed head screws) designed for

reliable working. Be sure to use a bit that matches

the screw in shape and size. Set the torque, as

described elsewhere in these operating instruc-

tions, to suit the size of screw.

7. Cleaning, maintenance and

ordering of spare parts

Danger!

Always pull out the mains power plug before star-

ting any cleaning work.

7.1 Cleaning

•

Keep all safety devices, air vents and the

motor housing free of dirt and dust as far as

possible. Wipe the equipment with a clean

cloth or blow it with compressed air at low

pressure.

•

We recommend that you clean the device

immediately each time you have finished

using it.

•

Clean the equipment regularly with a moist

cloth and some soft soap. Do not use

cleaning agents or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The

ingress of water into an electric tool increases

the risk of an electric shock.

7.2 Maintenance

There are no parts inside the equipment which

require additional maintenance.

7.3 Ordering spare parts and accessories

Please provide the following information when

ordering spare parts:

•

Type of unit

•

Article number of the unit

•

ID number of the unit

•

Spare part number of the required spare part

For our latest prices and information please go to

www.isc-gmbh.info

Tip! For good results we

recommend high-quality ac-

cessories from !

www.kwb.eu

welcome@kwb.eu

Anl_TC_CD_18_2_Li_SPK1.indb 18Anl_TC_CD_18_2_Li_SPK1.indb 18 05.09.2016 14:13:0905.09.2016 14:13:09

GB

- 19 -

8. Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw

materials in this packaging can be reused or

recycled. The equipment and its accessories are

made of various types of material, such as metal

and plastic. Never place defective equipment in

your household refuse. The equipment should

be taken to a suitable collection center for proper

disposal. If you do not know the whereabouts of

such a collection point, you should ask in your

local council oﬃ ces.

9. Storage

Store the equipment and accessories out of

children’s reach in a dark and dry place at above

freezing temperature. The ideal storage tempe-

rature is between 5 and 30 °C. Store the electric

tool in its original packaging.

Anl_TC_CD_18_2_Li_SPK1.indb 19Anl_TC_CD_18_2_Li_SPK1.indb 19 05.09.2016 14:13:0905.09.2016 14:13:09

GB

- 20 -

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EU concerning old electric and electronic equipment and

its implementation in national laws, old electric power tools have to be separated from other waste and

disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment

must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment.

The old equipment can be returned to a suitable collection point that will dispose of the equipment in

accordance with the national recycling and waste disposal regulations. This does not apply to any ac-

cessories or aids without electrical components supplied with the old equipment.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers

accompanying products is permitted only with the express consent of the iSC GmbH.

Subject to technical changes.

This consignment contains lithium-ion batteries.

In accordance with special provision 188 this consignment is not subject to the ADR regulations. Handle

with care. Danger of ignition in case of damage to the consignment package. If the consignment packa-

ge is damaged: Check and if necessary repackage. For further information contact: 0049 1807 10 20 20

66 (ﬁ xed network 14 ct/min, mobile phone max. 42 ct/min) Outside Germany charges will apply instead

for a regular call to a landline number in Germany.

Anl_TC_CD_18_2_Li_SPK1.indb 20Anl_TC_CD_18_2_Li_SPK1.indb 20 05.09.2016 14:13:0905.09.2016 14:13:09

GB

- 21 -

Service information

We have competent service partners in all countries named on the guarantee certiﬁ cate whose contact

details can also be found on the guarantee certiﬁ cate. These partners will help you with all service re-

quests such as repairs, spare and wearing part orders or the purchase of consumables.

Please note that the following parts of this product are subject to normal or natural wear and that the

following parts are therefore also required for use as consumables.

Category Example

Wear parts* Drill chuck, Battery

Consumables* Bit inserts/drill bits

Missing parts

* Not necessarily included in the scope of delivery!

In the eﬀ ect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Ple-

ase ensure that you provide a precise description of the problem and answer the following questions in

all cases:

•

Did the equipment work at all or was it defective from the beginning?

•

Did you notice anything (symptom or defect) prior to the failure?

•

What malfunction does the equipment have in your opinion (main symptom)?

Describe this malfunction.

Anl_TC_CD_18_2_Li_SPK1.indb 21Anl_TC_CD_18_2_Li_SPK1.indb 21 05.09.2016 14:13:1005.09.2016 14:13:10

GB

- 22 -

Warranty certiﬁ cate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the

unlikely event that your device develops a fault, please contact our service department at the address

shown on this guarantee card. You can also contact us by telephone using the service number shown.

Please note the following terms under which guarantee claims can be made:

1. These guarantee terms apply to consumers only, i.e. natural persons intending to use this product

neither for their commercial activities nor for any other self-employed activities. These warranty

terms regulate additional warranty services, which the manufacturer mentioned below promises to

buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee

claims are not aﬀ ected by this guarantee. Our guarantee is free of charge to you.

2. The warranty services cover only defects due to material or manufacturing faults on a product which

you have bought from the manufacturer mentioned below and are limited to either the rectiﬁ cation of

said defects on the product or the replacement of the product, whichever we prefer.

Please note that our devices are not designed for use in commercial, trade or professional applica-

tions. A guarantee contract will not be created if the device has been used by commercial, trade or

industrial business or has been exposed to similar stresses during the guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due to incorrect

installation, a failure to follow the operating instructions (for example connecting it to an incorrect

mains voltage or current type) or a failure to follow the maintenance and safety instructions or by ex-

posing the device to abnormal environmental conditions or by lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the device or the

use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand,

stones or dust, transport damage), the use of force or damage caused by external forces (for ex-

ample by dropping it).

- Damage to the device or parts of the device caused by normal or natural wear or tear or by normal

use of the device.

4. The guarantee is valid for a period of 24 months starting from the purchase date of the device. Gu-

arantee claims should be submitted before the end of the guarantee period within two weeks of the

defect being noticed. No guarantee claims will be accepted after the end of the guarantee period.

The original guarantee period remains applicable to the device even if repairs are carried out or

parts are replaced. In such cases, the work performed or parts ﬁ tted will not result in an extension

of the guarantee period, and no new guarantee will become active for the work performed or parts

ﬁ tted. This also applies if an on-site service is used.

5. To make a claim under the guarantee, please register the defective device at: www.isc-gmbh.info.

Please keep your bill of purchase or other proof of purchase for the new device. Devices that are

returned without proof of purchase or without a rating plate shall not be covered by the guarantee,

because appropriate identiﬁ cation will not be possible. If the defect is covered by our guarantee,

then the item in question will either be repaired immediately and returned to you or we will send you

a new replacement.

Of course, we are also happy oﬀ er a chargeable repair service for any defects which are not covered by

the scope of this guarantee or for units which are no longer covered. To take advantage of this service,

please send the device to our service address.

Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as

set out in the service information in these operating instructions.

Anl_TC_CD_18_2_Li_SPK1.indb 22Anl_TC_CD_18_2_Li_SPK1.indb 22 05.09.2016 14:13:1005.09.2016 14:13:10

Page is loading ...

Yang/Product-ManagementWeichselgartner/General-Manager

- 94 -

D erklärt folgende Konformität gemäß EU-Richtlinie und

Normen für Artikel

GB explains the following conformity according to EU directi-

ves and norms for the following product

F déclare la conformité suivante selon la directive CE et les

normes concernant l’article

I dichiara la seguente conformità secondo la direttiva UE e

le norme per l’articolo

NL verklaart de volgende overeenstemming conform EU

richtlijn en normen voor het product

E declara la siguiente conformidad a tenor de la directiva y

normas de la UE para el artículo

P declara a seguinte conformidade, de acordo com a

directiva CE e normas para o artigo

DK attesterer følgende overensstemmelse i medfør af

EU-direktiv samt standarder for artikel

S förklarar följande överensstämmelse enl. EU-direktiv och

standarder för artikeln

FIN vakuuttaa, että tuote täyttää EU-direktiivin ja standardien

vaatimukset

EE tõendab toote vastavust EL direktiivile ja standarditele

CZ vydává následující prohlášení o shodě podle směrnice EU

a norem pro výrobek

SLO potrjuje sledečo skladnost s smernico EU in standardi za

izdelek

SK vydáva nasledujúce prehlásenie o zhode podľa smernice

EÚ a noriem pre výrobok

H a cikkekhez az EU-irányvonal és Normák szerint a

következő konformitást jelenti ki

PL deklaruje zgodność wymienionego poniżej artykułu z

następującymi normami na podstawie dyrektywy WE.

BG декларира съответното съответствие съгласно

Директива на ЕС и норми за артикул

LV paskaidro šādu atbilstību ES direktīvai un standartiem

LT apibūdina šį atitikimą EU reikalavimams ir prekės normoms

RO declară următoarea conformitate conform directivei UE şi

normelor pentru articolul

GR δηλώνει την ακόλουθη συμμόρφωση σύμφωνα με την

Οδηγία ΕΚ και τα πρότυπα για το προϊόν

HR potvrđuje sljedeću usklađenost prema smjernicama EU i

normama za artikl

BIH potvrđuje sljedeću usklađenost prema smjernicama EU i

normama za artikl

RS potvrđuje sledeću usklađenost prema smernicama EZ i

normama za artikal

RUS следующим удостоверяется, что следующие продукты

соответствуют директивам и нормам ЕС

UKR проголошує про зазначену нижче відповідність виробу

директивам та стандартам ЄС на виріб

MK ја изјавува следната сообрзност согласно

ЕУ-директивата и нормите за артикли

TR Ürünü ile ilgili AB direktiﬂ eri ve normları gereğince aşağıda

açıklanan uygunluğu belirtir

N erklærer følgende samsvar i henhold til EU-direktivet og

standarder for artikkel

IS Lýsir uppfyllingu EU-reglna og annarra staðla vöru

Konformitätserklärung

Akku-Bohrschrauber TC-CD 18-2 Li / Ladegerät für TC-CD 18-2 Li (Einhell)

87/404/EC_2009/105/EC

2005/32/EC_2009/125/EC

2006/95/EC

2006/28/EC

X

2014/30/EC

2004/22/EC

1999/5/EC

97/23/EC

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

X

2011/65/EC

X

2006/42/EC

Annex IV

Notiﬁ ed Body:

Notiﬁ ed Body No.:

Reg. No.:

2000/14/EC_2005/88/EC

Annex V

Annex VI

Noise: measured L

WA

= dB (A); guaranteed L

WA

= dB (A)

P = KW; L/Ø = cm

Notiﬁ ed Body:

2004/26/EC

Emission No.:

Standard references: EN 60745-1; EN 60745-2-1; EN 60745-2-2; EN 55014-1;

EN 55014-2; EN 61000-3-2; EN 61000-3-3; EN 60335-1; EN 60335-2-29; EN 62233

Landau/Isar, den 04.08.2016

First CE: 15 Archive-File/Record: NAPR014815

Art.-No.: 45.138.46 I.-No.: 11016 Documents registrar: Georg Riedel

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

Anl_TC_CD_18_2_Li_SPK1.indb 94Anl_TC_CD_18_2_Li_SPK1.indb 94 05.09.2016 14:13:2205.09.2016 14:13:22

Page is loading ...

Einhell Classic TC-CD 18-2 LI User manual

This manual is also suitable for

Einhell Classic TC-CD 18-2 LI User manual

in other languages

Related papers

Other documents