PEAQ PDR200 B W Owner's manual

Category
CD players
Type
Owner's manual

This manual is also suitable for

Bedienungsanleitung Mode d’emploi
Οδηγίες χρήσης Kezelési leírás
User Manual Manuale dell’utente
Manual de instrucciones
Micro Audio System PMS200BT-B/W
PMS200BT_A5_131031_1.indb 1 31/10/13 2:53 PM
Deutsch 4 - 17
Ελληνικά 18 - 31
English 32 - 45
Español 46 - 59
Français 60 - 73
Magyar 74 - 87
Italiano 88 - 101
PMS200BT_A5_131031_1.indb 3 31/10/13 2:53 PM
ENGLISH
32
Important Safety Instructions. Please read
the instructions carefully and keep them for
later use.
DANGER! Invisible laser radiation
when open and safety interlock
failed or defeated. Avoid direct
exposure to the beam. Do not touch the
lens.
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
WARNING: SHOCK HAZARD - DO NOT OPEN
AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR
The lightning flash with arrow
head within an equilateral triangle
is intended to alert the user to the
presence of uninsulated “dangerousvoltage”
within the product’s enclosure that may be
of sucient magnitude to constitute a risk of
electric shock to persons and animals.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance in-
structions in the literature accompanying the
device.
For safety reasons, this class II
product is provided with double or
reinforced insulation as indicated
by this symbol.
This product is only intended for audio
entertainment. Do not use the product for
any other purpose than described in this
manual in order to avoid any hazardous
situation. Improper use is dangerous and
will void any warranty claim.
For household use only. Do not use
outdoors.
Danger! Excessive sound pressure from
earphones and headphones can cause
hearing loss. If you listen to loud music for
a long time, your hearing may be impaired.
Set to a moderate volume.
Danger of suocation! Keep all packag-
ing material away from children.
Only use under normal room temperature
and humidity conditions.
The product is only suitable for use at
moderate degrees of latitude. Do not
use in the tropics or in particularly humid
climates.
Do not move the product from cold into
warm places and vice versa. Condensa-
tion can cause damage to the product and
electrical parts.
Do not use attachments or accessories
other than recommended by the manu-
facturer or sold with this product. Install in
accordance with this user manual.
Do not install near any heat sources such
as radiators, heat registers, stoves or other
products (including amplifiers) that pro-
duce heat.
Do not shift or move the product when
powered on.
Do not touch, push or rub the surface
of the product with any sharp or hard
objects.
Danger! To reduce the risk of fire or elec-
tric shock, do not expose this product to
rain or moisture.
The product shall not be exposed to drip-
ping or splashing and no objects filled with
liquids, such as vases, shall be placed on
the product.
Care should be taken so that no objects
or liquids enter the enclosure through
openings.
No naked flame sources, such as lighted
candles, should be placed on the product.
Refer all servicing to authorised service
agent. Do not attempt to repair the prod-
uct yourself. Servicing is required when
the product has been damaged in any
way, such as the supply cord or plug are
damaged, liquid has been spilled, objects
have fallen into the product, the enclosure
is damaged, the product has been ex-
posed to rain or moisture, does not oper-
Safety instructions
PMS200BT_A5_131031_1.indb 32 31/10/13 2:54 PM
33
ENGLISH
ate normally, or has been dropped.
Before connecting the product to a socket
outlet, make sure the voltage indicated
on the product corresponds to your local
mains.
If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent or similarly qualified person in order
to avoid hazard.
Regularly check if the supply cord, prod-
uct or extension cable is defective. If found
defective, do not put the product into op-
eration. Immediately pull the plug.
Place the supply cord and, if necessary,
an appropriate extension cable in such
away that pulling or tripping over it is im-
possible. Do not allow the supply cord to
hang down within easy reach.
Do not jam, bend or pull the supply cord
over sharp edges.
The power plug is used as the disconnect
device; the disconnect device shall re-
main readily operable. To completely dis-
connect the power input, disconnect the
mains plug.
The product may not function properly or
not react to the operation of any control
due to electrostatic discharge. Switch o
and disconnect the product; reconnect af-
ter a few seconds.
Protect the supply cord from being walked
on or pinched particularly at the plug, con-
venience receptacles and the point where
it exits from the product.
Never pull the plug by the supply cord or
with wet hands.
Disconnect the power plug in case of
faults during use, during lightening storms,
before cleaning and when not using the
product for a longer period of time.
Danger! Before cleaning, switch the prod-
uct o and disconnect the power plug
from the socket.
When the product has reached the end of
its service life, make it defective by discon-
necting the plug from the socket and cut-
ting the cord in two.
Caution! There is danger of explosion
from improper replacement of the batter-
ies. Replace batteries only with the same
or equivalent type of battery.
Always change the entire battery pack. Do
not mix old and new batteries, or batteries
with dierent charge state.
Make sure the batteries are correctly in-
serted. Observe the polarity (+) plus / (-)
negative on the battery and the housing.
Improperly inserted batteries can lead to
leakage or, in extreme cases, a fire or an
explosion.
Remove used batteries. Remove the bat-
teries if you know that the product will not
be used for a longer period of time. Oth-
erwise, the batteries could leak and cause
damage.
If the batteries leak, remove them with a
cloth and dispose of them accordingly.
Prevent battery acid from coming into
contact with skin and eyes. If you do
get battery acid in your eyes, flush them
thoroughly with lots of water and consult
a physician immediately. If battery acid
comes into contact with your skin, wash
the aected area with lots of water and
soap.
When installing the device, leave su-
cient space for ventilation. Do not install
in bookcases, built-in cabinets or the like.
Do not impede ventilation by covering the
ventilation openings with items, such as
newspapers, table-cloths, curtains, etc.
Do not insert any objects.
PMS200BT_A5_131031_1.indb 33 31/10/13 2:54 PM
ENGLISH
34
Partlist
1 1432 5 76 8
1 Speaker
2 Main unit
3 Touch panel
4 SD card slot
5. USB SD cover
6 USB port
7 Earphone jack
8 CD tray
109 11 12 13 14 15 9
9 Speaker cable
10 Antenna
11 AUX INPUT
12 Audio OUTPUT (R)
13 Audio OUTPUT (L)
14 Power switch
15 Power cord with plug
PMS200BT_A5_131031_1.indb 34 31/10/13 2:54 PM
35
ENGLISH
1 x User manual
1 x Main unit
2 x Speaker
2 x Detachable Speaker Cloth
1 x Remote control
1 x Quick start guide
1 x Warranty card
Touchpanel
1 2 3 4 5 6 7 8 9 10
1 / I icon
Turn on or into standby
2 icon
Play or pause the playback
3 icon
Fast rewind current track or skip to previ-
ous track
4 icon
Stop the playback
5 icon
Fast forward current track or skip to next
track
6 Screen
7 MODE icon
Change mode
8 MEMORY icon
Confirm setting
9
icon
Open or close CD tray
10 Volume knob
Increase or decrease volume
Accessories
PMS200BT_A5_131031_1.indb 35 31/10/13 2:54 PM
ENGLISH
36
Remote control
Increase/decrease volume
Confirm setting
Change mode
Change folder
Number buttons 0-9
Battery compartment
Play INTRO
Repeat playback
Play in random order
Sleep mode
Set timer
Play/pause
Stop
Fast rewind/
Previous
Fast forward/
Next
EQ
Equalizer
Change to mono/stereo
Turn o the sound
Open/close CD tray
Turn on/standby
PMS200BT_A5_131031_1.indb 36 31/10/13 2:54 PM
37
ENGLISH
OperationSetup
Select a stable, level and clean surface to
place the product. Route cables so that they
do not become a trip hazard and do not
place heavy or sharp objects on the cables
or units. Leave about 10 cm for ventilation
around the product.
AUDIO INPUT
Connect the playback device with the RCA
cable (red/white) to the AUX input.
NOTE: RCA cable is not included.
SPEAKER CONNECTION
R L
Unwind speaker cables and connect the
cables to the main unit. Make sure by ob-
serving the correct polarity on the terminals
(blackis /whiteis ).
POWER SUPPLY
Connect the power plug to a suitable power
outlet.
POWER ON/OFF
Press the power switch on the rear of the
main unit to the ON position. Press on the
remote control or on the touch panel to turn
on the product.
INSERTING BATTERY
1. Open the battery compartment cover.
2. Insert the new batteries into the battery
compartment while paying attention to
the correct polarity.
3. Close the battery compartment cover.
PMS200BT_A5_131031_1.indb 37 31/10/13 2:54 PM
ENGLISH
38
STANDBY
To turn the product back into standby mode,
press on the remote control or on the
touch panel.
NOTE: During standby mode, indicator
will be displayed on the touch panel.
ANTENNA
Try dierent positions of the antenna to figure
out the best reception position.
VOLUME
Adjust the volume with the volume knob or
on the remote control.
MODE
Press MODE to select the following modes:
CD BT LINK
USB AUX
CARD TUNER
CLOCK SETUP
1. During standby mode, press and hold
MEMORY on the remote control.
2. 24-HOUR (or 12-HOUR) starts flashing
on the screen. Press
or to adjust
the 24/12 hour format and confirm by
pressing MEMORY.
3. The hour digits AM (or PM) start flashing.
Press
or to adjust the hour and
confirm by pressing MEMORY.
4. The minute digits start flashing. Press
or to adjust the minute and con-
firm by pressing MEMORY.
5. Now the time is set.
NOTE: Time setup can also be adjusted on
the touch panel.
TIMER
1. After the time is set, press TIMER on the
remote control for few seconds.
2.
ON indicator will be displayed on the
screen and hour digits start flashing.
Press
or to adjust the hour and
confirm by pressing TIMER.
3. The minute digits start flashing. Press
or to adjust the minute and con-
firm by pressing TIMER.
PMS200BT_A5_131031_1.indb 38 31/10/13 2:54 PM
39
ENGLISH
4. OFF indicator appears on the screen
and hour digits start flashing. Press
or to adjust the hour and confirm by
pressing TIMER.
5. The minute digits start flashing. Press
or to adjust the minute and con-
firm by pressing TIMER.
6. TUNER starts flashing. Press or
to select the mode TUNER / CD /
USB or CARD and confirm by pressing
TIMER.
7. VOL starts flashing on the screen. Press
or to adjust the volume and con-
firm by pressing TIMER.
8. The timer is set and the indicator will
be displayed on the screen.
NOTE: If TIMER ON and TIMER OFF has the
same time, ERROR will be displayed on the
screen.
SLEEP
Press SLEEP on the remote control to acti-
vate sleep mode.
The
indicator and SLEEP 90 will be dis-
played on the screen. Press SLEEP to de-
crease sleep intervals:
SLEEP 90 90 minutes
SLEEP 80 80 minutes
SLEEP 70 70 minutes
SLEEP 60 60 minutes
SLEEP 50 50 minutes
SLEEP 40 40 minutes
SLEEP 30 30 minutes
SLEEP 20 20 minutes
SLEEP 10 10 minutes
SLEEP OFF o
MUTE
Press MUTE on the remote control to turn o
the volume temporarily. The volume indicator
starts flashing.
Press MUTE again to deactivate.
PLAY / PAUSE
Press
to start or pause the playback. If
the playback is paused, the time elapsed in-
dicator is flashing on the screen.
NOTE: Very high volumes can cause vibra-
tions which could also make the tracks skip.
STOP PLAYBACK
Press
to stop the playback.
PREVIOUS / NEXT
With
or , you can skip tracks to the
next or previous track. By pressing
once,
the track being played will be played back
again from the start. By pressing twice, the
previous title will be played again. By press-
ing
, the next track will be played.
PMS200BT_A5_131031_1.indb 39 31/10/13 2:54 PM
ENGLISH
40
FAST REWIND / FAST FORWARD
By holding down the buttons
or , you
can fast forward or rewind the current track.
Once the desired place has been found, let
go of the button in order to proceed with the
playback.
TRACK SELECTION
Press the respective number button 0-9
on the remote control and wait approx. 3
seconds.
EQUALIZER
Press EQ to select FLAT / CLASSIC / ROCK
/ POP or JAZZ.
RANDOM
Press RANDOM on the remote control to
play all tracks in random order. RANDOM will
be displayed on the screen.
Press RANDOM again to deactivate the
function.
NOTE: RANDOM can only be used in USB/
CARD and CD mode.
INTRO
Press INTRO on the remote control to play
the first 10 seconds of each track. INTRO will
be displayed on the screen.
Press INTRO again to deactivate the
function.
NOTE: INTRO can only be used in USB/
CARD and CD mode.
PMS200BT_A5_131031_1.indb 40 31/10/13 2:54 PM
41
ENGLISH
TUNER playback
Press MODE and select TUNER.
MANUAL TUNING
Press
or to tune the desired wave
band range of frequency.
AUTO TUNING
1. Press and hold
or for few sec-
onds and release the button.
2. The tuner will automatically search the
first station.
3. Repeat the above procedure to select
another station.
SAVING STATIONS
You can store up to 30 FM stations.
1. Once a station is found, press MEMORY
on the remote control.
2. Press
or on the remote control to
select the desired station number.
3. Press MEMORY to confirm the selection.
4. To program more station or to change
the stored preset stations, repeat the
above steps.
NOTE: Storing a new station into a preset
location will erase the previously stored sta-
tion. Power o will not erase the memory of
preset stations.
SELECT PRESET STATIONS
1. Press
or on the remote control to
select the preset stations.
2. The screen will display the number and
the corresponding frequency.
MONO / STEREO
1. Press MONO/ST. on the remote control
to select MONO or STEREO.
2. When you receive a FM stereo station
the
indicator will be displayed
on the screen.
PMS200BT_A5_131031_1.indb 41 31/10/13 2:54 PM
ENGLISH
42
CD playback
Press MODE and select CD.
EJECT / LOAD A DISC
1. Open the CD tray by pressing OPEN/
CLOSE or
on the touch panel. The CD
tray cover will open upwards. Remove
the transport safeguard when opening
the CD tray for the first time.
2. Put one CD into the CD tray with the la-
bel side facing up. Press on a point in the
middle of the CD until it clicks into place
on the axis.
3. Press OPEN/CLOSE to close the CD
tray. The CD will now be read.
4. The total number of tracks on the CD is
displayed on the screen and will play the
first track automatically.
NOTE: Before you open the CD tray again,
always press first to stop the CD from
spinning. To remove the CD, place one finger
in the middle of the CD (middle of the spin-
dle) and the other finger on the edge of the
CD. Carefully pull the CD out of the tray.
REPEAT FUNCTION
Press REPEAT to select the following repeat
modes:
REPEAT repeat current track
REPEAT ALL repeat all tracks
REPEAT ALBUM repeat album
NOTE: Repeat album will be displayed only
for CD with MP3/WMA music files.
FOLDER SELECTION
For CD with MP3/WMA playback.
Press
or on the remote control to change
the folder.
ID3 OPERATION
For CD with MP3/WMA playback.
1. During MP3/WMA playback, press
MEMORY to turn on ID3 operation.
2. TITLE NAME / ARTIST NAME / ALBUM
NAME will be displayed on the screen.
3. Press MEMORY again to turn o ID3
operation.
PLAYBACK LIST
The playback list can only be programmed
in stop mode.
1. While in stop mode, press MEMORY,
track number 00 starts flashing.
2. Press
or on the remote control to
select the track and confirm by pressing
MEMORY.
3. Up to 32 tracks can be programmed.
4. Press to play the first track of the
program.
NOTE: For CD with MP3/WMA music files
you can can follow the steps in USB/CARD
playback.
CANCEL PLAYBACK LIST
In stop mode, press
to cancel the program
or open the CD tray by pressing OPEN/
CLOSE or on the touch panel.
PMS200BT_A5_131031_1.indb 42 31/10/13 2:54 PM
43
ENGLISH
USB/CARD playback
USB
1. Press MODE and select USB.
2. Open the USB SD cover and insert a
USB Stick with MP3/WMA music files.
3. Playback starts automatically and the
first track will be played. If there is no
USB device connected, the message
NO USB will be displayed on the screen.
NOTE: Connect the USB device directly to
the USB port of the unit. Using an extension
cable is not recommended and may cause
interference and failure of data transfer.
This product supports USB 1.1 and 2.0.
Charging external devices
External devices can be charged via USB
with this speaker. Connect the device to the
USB port (output: 5V/ 500mA).
NOTE: USB charging cable is not included
(please use cable provided with your external
device, if any)
SD CARD
1. Press MODE and select CARD.
2. Open the USB SD cover and insert an
SD card with MP3/WMA music files.
3. Playback starts automatically and the
first track will be played. If there is no SD
card connected, the message NO CARD
will be displayed on the screen.
REPEAT FUNCTION
Press REPEAT to select the following repeat
modes:
REPEAT repeat current track
REPEAT ALL repeat all tracks
REPEAT ALBUM repeat album
FOLDER SELECTION
Press
or on the remote control to change
the folder.
ID3 OPERATION
1. During MP3/WMA playback, press
MEMORY to turn on ID3 operation.
2. TITLE NAME / ARTIST NAME / ALBUM
NAME will be displayed on the screen.
3. Press MEMORY again to turn o ID3
operation.
PLAYBACK LIST
The playback list can only be programmed
in stop mode.
1. Press MODE and select USB or CARD.
2. While in stop mode, press MEMORY,
album number 00 starts flashing.
3. Press
or on the remote control to
select the folder and confirm by pressing
MEMORY.
4. Track number 000 starts flashing.
5. Press or on the remote control to
select the track and confirm by pressing
MEMORY.
6. Up to 64 tracks can be programmed.
7. Press to play the first track of the
program.
CANCEL PLAYBACK LIST
In stop mode, press
to cancel the program.
PMS200BT_A5_131031_1.indb 43 31/10/13 2:54 PM
ENGLISH
44
AUX Bluetooth
Connect the playback music device to the
AUX input with RCA cable (Red/White).
1. Press MODE and select AUX.
2. Now you can start playback on your mu-
sic device.
NOTE: RCA cable is not included.
1. Press MODE and select BT LINK. BT
LINK starts flashing on the screen.
2. Activate bluetooth on the bluetooth mu-
sic device.
3. Select and confirm BT speakerN for
pairing.
4. BT LINK stops flashing once the devices
are connected.
5. Now you can start playback on your
bluetooth music device.
Disposal
Do not dispose of this appliance as
unsorted municipal waste. Return it
to a designated collection point for
the recycling of WEEE. By doing so, you will
help to conserve resources and protect the
environment. Contact your retailer or local
authorities for more information.
PMS200BT_A5_131031_1.indb 44 31/10/13 2:54 PM
45
ENGLISH
Specifications
POWER SUPPLY
Input
Operation power consumption
Standby power consumption
Radio
Frequency range
CD Playback
Frequency response
Compatibility
Remote control
Batteries
Connectivity
USB
SD card
Bluetooth
Bluetooth profiles
Bluetooth range
Bluetooth version
AUX
Speaker
Output power (RMS)
Sound Enhancement
Sound System
Headphone output power
Dimension
Main unit (W x H x D)
Speaker box (W x H x D)
Weight (Main unit and two speakers)
230-240 V~, 50 Hz
33 W
< 1 W
Digital FM only, 88-108 MHz
100-16 KHz at -3 dB
CD-DA/CD-R/CD-RW/MP3
2 x AAA (not included)
YES
YES
YES, iBT-03
A2DP, AVRCP
2.4-2.483 GHz
Class 2
AUX IN
2 x 10W RMS
Flat/Classic/Rock/Pop/Jazz
Flat/Classic/Rock/Pop/Jazz
250-280 mV at 32 OHM (1K 0dB)
approx. 220 x 244 x 118 mm
approx. 138 x 200 x 226 mm
approx. 5.54 kg
NOTE: WMA protected DRM FILE is not
supported on this product.
PMS200BT_A5_131031_1.indb 45 31/10/13 2:54 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103

PEAQ PDR200 B W Owner's manual

Category
CD players
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI