Pioneer ND-BC2 User manual

Brand: Pioneer

Model: ND-BC2

Category: Security cameras

Type: User manual

This manual is also suitable for

ND BC2

Fig. 11-2

Abb. 11-2

Fig. 11-3

Abb. 11-3

Fig. 11-1

Abb. 11-1

Fig. 11-4

Abb. 11-4

PIONEER CORPORATION

4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936

TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS OF CANADA, INC.

300 Allstate Parkway, Markham, Ontario L3R OP2, Canada

TEL: 1-877-283-5901

PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.

Blvd. Manuel Avila Camacho 138 10 piso

Col. Lomas de Chapultepec, Mexico, D.F. 11000

TEL: 55-9178-4270

Published by Pioneer Corporation.

Publication de Pioneer Corporation.

Tous droits de reproduction et de traduction

réservés.

Printed in Japan

Imprimé au Japon

<CZR5068-A> E<KSKNN> <06J00000>

Universal Rear View Camera

Caméra de recul universelle

Owner’s Manual

Mode d’emploi

ND-BC2

① Glass surface

② Make sure it doesn’t touch the wiper

③ Install on the center part

Fig. 1

Abb. 1

𝖠 Rear view camera × 1 𝖢 Power supply unit × 1𝖡 RCA power supply cable × 1

𝖣 Hexagon wrench × 1 𝖤 Velcro tape

(soft type) × 1

𝖥 Velcro tape

(hard type) × 1

𝖧 Waterproof

pad × 1

𝖦 Clamp × 10 𝖨 Double-sided

tape × 1

③ Camera stand

⑤ Camera stand

① Turn

② Twist

① Camera

stand

② When sticking to the center

④ Installation

screw

③ Bottom

① Top

② Bottom

① Top

Fig. 4

Abb. 4

Fig. 6

Abb. 6

Fig. 7

Abb. 7

Fig. 5

Abb. 5

② Rear view

camera

Fig. 8

Abb. 8

Fig. 9

Abb. 9

③ Bumper or rear edge of car

① Power supply unit

② Velcro tape

(hard type)

③ Velcro tape

(soft type)

Fig. 10

Abb. 10

Fig. 12

Abb. 12

Fig. 13

Abb. 13

① Angle of view

Horizontal: 135°

② Angle of view

Vertical: 100°

𝖩 Camera stand bracket 𝖢 × 1

𝖡

𝖠

Fig. 2

Abb. 2

Fig. 3-1

Abb. 3-1

Fig. 3-2

Abb. 3-2

Fig. 3-3

Abb. 3-3

Fig. 3-4

Abb. 3-4

③ Mark

③ When attaching using camera stand bracket 𝖢

(attaching while rotating by 90°)

Si desea deshacerse de este producto, no

lo mezcle con los residuos generales de su

hogar. De conformidad con la legislación

vigente, existe un sistema de recogida dis-

tinto para los productos electrónicos que

requieren un procedimiento adecuado de

tratamiento, recuperación y reciclado.

Las viviendas privadas en los 25 estados miembros

de la UE, en Suiza y Noruega pueden devolver gra-

tuitamente sus productos electrónicos usados en las

instalaciones de recolección previstas o bien en las

instalaciones de minoristas (si adquieren un producto

similar nuevo).

En el caso de los países que no se han mencionado

en el párrafo anterior, póngase en contacto con sus

autoridades locales a fin de conocer el método de

eliminación correcto.

Al actuar siguiendo estas instrucciones, se asegurará

de que el producto de desecho se somete a los pro-

cesos de tratamiento, recuperación y reciclaje nec-

esarios, con lo que se previenen los efectos negativos

potenciales para el entorno y la salud humana.

• La instalación y cableado de este producto requiere

la habilidad y experiencia de un especia-lista. Para

asegurar la seguridad, solicite un técnico especial-

ista para instalar la unidad.

• No intente calentar la superficie del objetivo de

la cámara o el propio objetivo de la cámara con

un encendedor o algo similar cuando los mismos

estén congelados. Eso puede causar un fallo de

funcionamiento.

• Este producto es una cámara de vista posterior

para verificar la vista en la parte trasera de un

coche.

Una cámara de vista posterior es una cámara que

provee imágenes simétricas de la misma manera

que los espejos retrovisores o laterales.

• Se puede hacer la conexión a un televisor con

entrada de vídeo RCA, pero compruebe si el tel-

evisor tiene una función de conexión de marcha

atrás.

• La luz directa del sol o luz fuerte (luz del sol refle-

jada de un parachoques, etc.) en la cámara puede

producir una mancha por encima y por debajo de

la ubicación donde la luz radia, pero esto no es un

fallo de funcionamiento.

• Este producto ha sido diseñado para complementar

la vista trasera del conductor, pero las imágenes

de la cámara no muestran todos los peligros y

obstáculos. Asegúrese de mirar atrás cuando vaya

de marcha atrás para comprobar la vista.

• Este producto tiene una lente de gran angular y,

por lo tanto, la vista cercana es amplia y la vista

distante es estrecha, lo que puede crear una sen-

sación falsa de la distancia. Asegúrese de mirar

atrás cuando vaya de marcha atrás para comprobar

la vista.

• No lave su coche en un túnel de lavado automático

o agua de alta presión, ya que esto puede resultar

en la entrada de agua en la cámara o caída de la

cámara.

• Verifique la instalación del soporte de la cámara

antes de conducir el coche.

¿No están flojos los tornillos?

– ¿Está firmemente fijo el soporte de la cámara?

– Si la cámara de vista posterior se afloja mien-

tras está conduciendo, esto puede causar un

accidente.

This device complies with Part 15 of the FCC

Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

Information to User

Alteration or modifications carried out without

appropriate authorization may invalidate the user’s

right to operate the equipment.

If you want to dispose this product, do not

mix it with general household waste. There

is a separate collection system for used elec-

tronic products in accordance with legisla-

tion that requires proper treatment, recovery

and recycling.

Private households in the 25 member states of the

EU, in Switzerland and Norway may return their

used electronic products free of charge to designated

collection facilities or to a retailer (if you purchase a

similar new one).

For countries not mentioned above, please contact

your local authorities for the correct method of dis-

posal.

By doing so you will ensure that your disposed prod-

uct undergoes the necessary treatment, recovery and

recycling and thus prevent potential negative effects

on the environment and human health.

WARNING:

Handling the cord on this product or cords associated

with accessories sold with the product may expose

you to chemicals listed on proposition 65 known to

the State of California and other governmental enti-

ties to cause cancer and birth defects or other repro-

ductive harm. Wash hands after handling.

• Installation and wiring of this product require spe-

cialist skill and experience. To assure your safety,

please request a specialist technician to install the

unit.

• Do not attempt to heat the surface of the camera

lens or camera lens itself with a lighter and so on

when they have become frozen. This can cause a

malfunction.

• This product is a rear view camera for checking

the view at the rear of a car.

A rear view camera is a camera that provides sym-

metrical images in the same way as rear and side

view mirrors.

• Connection to a TV with an RCA video input is

possible, but confirm whether the TV you use has

a reverse gear connection function.

• Direct sunlight or strong light (sunlight reflected

from a bumper etc) on the camera may result in

smear above and below the location where the

light strikes, but this is not a malfunction.

• This product is designed to supplement the driver’

s rear view, but the camera images do not show all

dangers and obstacles. Be sure to look behind you

when reversing to confirm the view.

• This product features a wide-angle lens, so the

near view is wide and the far view is narrow,

which may create a false sense of distance. Be

sure to look behind you when reversing to confirm

the view.

• Do not wash your car with an automatic car wash

or high-pressure water as it may result in water

entering the camera or the camera falling off.

• Check camera stand installation before driving.

Are the screws loose?

– Is the camera stand firmly secured?

– If the rear view camera comes loose while you

are driving it may cause an accident.

Installation <ENGLISH>

Parts supplied

𝖠 Rear view camera × 1

𝖡 RCA power supply cable × 1

𝖢 Power supply unit × 1

𝖣 Hexagon wrench × 1

𝖤 Velcro tape (soft type) × 1

𝖥 Velcro tape (hard type) × 1

𝖦 Clamp × 10

𝖧 Waterproof pad × 1

𝖨 Double-sided tape × 1

𝖩 Camera stand bracket 𝖢 × 1

Installation example (Fig. 1)

① Glass surface

② Make sure it doesn’t touch the wiper

③ Install on the center part

Changing the orientation of camera

stand installation (Fig. 11-1)

The camera stand can be installed in

various ways by changing the direction in

which camera stand bracket 𝖡 is attached

or attaching camera stand bracket 𝖢.

Change to match your car’s shape or the

installation site.

1. Use the hexagon wrench to remove

the screws securing camera stand

brackets 𝖠 and 𝖡. (Fig. 2)

2. Change the direction of installation

bracket 𝖡. (Fig. 3-1)

3. Reattach with the screws.

Installing Using Camera Stand Bracket 𝖢

(Fig. 11-4)

1. Use the hexagon wrench to remove

the screws securing camera stand

brackets 𝖠 and 𝖡. (Fig. 2)

2. Attach camera stand bracket 𝖢 to

the camera stand. (Fig. 3-2)

3. Attach the rear view camera to cam-

era stand bracket 𝖡. (Fig. 3-3)

4. Attach the camera stand and rear

view camera. (Fig. 3-4)

Route the cables as shown in the figure so

that they do not become entangled.

Attach the camera stand while being care-

ful not to mistake the vertical orientation

of the rear view camera. (Fig. 7)

Installation Procedure

Note:

• Before making a final installation of the unit,

temporarily connect the wiring to confirm that

the connections are correct and the system works

properly.

• Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts

can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifica-

tions of the vehicle.

• Install the unit where it does not get in the driver’

s way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

• When mounting this unit, make sure none of the

leads are trapped between this unit and the sur-

rounding metalwork or fittings.

• To prevent electric shock, do not install the power

supply unit in places where it might come in con-

tact with liquids.

• Do not mount this unit near the heater outlet,

where it would be affected by heat, or near the

doors, where rainwater might splash onto it. (Never

install in locations such as the above because of

the danger of malfunction due to high tempera-

tures.)

• Before drilling any mounting holes always check

behind where you want to drill the holes. Do not

drill into the gas line, brake line, electrical wiring

or other important parts.

• If this unit is installed in the passenger compartment,

anchor it securely so it does not break free while the

car is moving, and cause injury or an accident.

• If this unit is installed under a front seat, make

sure it does not obstruct seat movement. Route

all leads and cords carefully around the sliding

mechanism so they do not get caught or pinched

in the mechanism and cause a short circuit.

• Locate in the position you want to install the rear

view camera. Adjust the angle of the rear view

camera, and install so that the camera doesn’t

touch the car.

• When sticking to a glass surface, stick it on in a

position that assures the camera doesn’t touch the

rear window.

• Install so that it does not obstruct the rear field of

view.

• Install so that it does not protrude from the side of

the car.

• Do not perform installation in rain or fog.

• When humidity is high, dry the surface to which

the unit is to be attached before installing. Moisture

on the attachment surface reduces adhesive

strength which may lead to the unit coming off.

IMPORTANT

SAFEGUARDS

PRECAUCIONES DE

SEGURIDAD IMPORTANTES

• If the temperature of the attachment surface is

low, warm with a hair dryer of other means before

installing to improve adhesive strength.

• Do not attach the camera stand to areas on the car

body treated with fluorocarbon resin, or glass. This

may result in the rear view camera falling off.

• During the 24-hour period after installing:

– Do not apply water to the unit.

– Do not expose the unit to rain.

– Do not subject the camera to unnecessary force.

• Thoroughly clean where tape is used for sticking

on the unit.

1. Clean the surface to which the rear

view camera is to be installed.

(Fig. 4)

Use a cloth or other item to wipe oil, wax,

dust and any other dirt from the installation

surface.

2. Remove the rear view camera from

the camera stand. (Fig. 5)

Remove the mounting screws with the

hexagon wrench provided.

① Top

② Rear view camera

③ Bottom

④ Installation screw

⑤ Camera stand

3. Align the camera stand with the

installation surface. (Fig. 6)

Adjust the camera stand so that there is no

space between it and the installation surface.

① Turn

② Twist

③ Camera stand

4. Attach the camera stand removed in

step 2 to the rear view camera with

the mounting screws. (Fig. 7)

The rear view camera has a mark indicat-

ing the top of the camera.

Attach the camera stand while being care-

ful not to mistake the vertical orientation

of the rear view camera.

① Top

② Bottom

③ Mark

5. Peel off the sheet on the back of they

camera stand and stick it on. (Fig. 8,

Fig. 9)

Press the camera stand with your fingers to

stick it to the installation surface. Touching

the adhesive surface or sticking the unit

on a second time reduces adhesive power

which may result in the unit coming off.

① Camera stand

② When sticking to the center

③ When attaching using camera stand bracket

𝖢 (attaching while rotating by 90°)

6. Adjust the angle so that the bumper

or rear edge of the car is displayed

at the bottom of the TV screen.

(Fig. 10, Fig. 11-2, Fig. 11-3, Fig. 12)

① Angle of view

Horizontal: 135°

② Angle of view

Vertical: 100°

③ Bumper or rear edge of car

7. Attach the power supply unit.

(Fig. 13)

Affix the Velcro tape (hard type) to the

bottom of the power supply unit, and affix

the Velcro tape (soft type) to the mounting

location.

① Power supply unit

② Velcro tape (hard type)

③ Velcro tape (soft type)

• You can use Velcro tape (hard type) to attach

directly to a carpet, but do not use the soft type.

• Install the power supply unit close enough

for the rear view camera cable to reach.

Page is loading ...

Fig. 16

Abb. 16

Fig. 17

Abb. 17

① Pull out from here

② Hinge

③ Harness cover

⑤ Hatch

④ Rear view

camera

① Rear view camera

② Hatch

③ Cord

② Waterproof pad

Fig. 18

Abb. 18

① Clamps

③ Rubber packing

④ Make a U-shaped loop in

the lead outside the rubber

packing to prevent rain-

water from flowing along

the lead into the interior

of the vehicle.

Connection <ENGLISH>

Note:

• This unit is for vehicles with a 12-volt battery and nega-

tive grounding. Before installing it in a recreational vehi-

cle, truck, or bus, check the battery voltage.

• To avoid shorts in the electrical system, be sure to discon-

nect the battery cable before beginning installation.

• Refer to the owner’s manual for details on connecting the

other units, then make connections correctly.

• Secure the wiring with cable clamps or adhesive tape. To

protect the wiring, wrap adhesive tape around them where

they lie against metal parts.

• Route and secure all wiring so it cannot touch any mov-

ing parts, such as the gear shift, handbrake and seat rails.

Do not route wiring in places that get hot, such as near

the heater outlet. If the insulation of the wiring melts or

gets torn, there is a danger of the wiring short-circuiting

to the vehicle body.

• Do not shorten any leads.

• Never feed power to other equipment by cutting the insu-

lation of the power supply lead of the unit and tapping

into the lead. The current capacity of the lead will be

exceeded, causing over heating.

• When replacing the fuse, be sure to only use a fuse of the

rating prescribed on the fuse holder.

• To minimize noise locate the TV antenna cable, radio

antenna cable and RCA power supply cable as far away

from each other as possible.

• Connection to a TV with an RCA video input is possible,

but confirm whether the TV you use has a reverse gear

connection function.

• If this unit is installed in a vehicle that does not have an

ACC (accessory) position on the ignition switch, the red

lead of the unit should be connected to a terminal coupled

with ignition switch ON/OFF operations. If this is not

done, the vehicle battery may be drained when you are

away from the vehicle for several hours.

ACC position No ACC position

• Cords for this product and those for other products may

be different colors even if they have the same function.

When connecting this product to another product, refer to

the supplied manuals of both products and connect cords

that have the same function.

Connection sample (Fig. 14)

① Power supply unit

② Rear view camera connector

③ RCA power supply cable connector

④ Rear view camera

Video input jack

Connect to video input jack.

⑤ RCA pin

Accessory power supply

To electric terminal controlled by ignition

switch (12 V DC) ON/OFF.

⑥ Red

⑦ Fuse (1A)

Ground

To vehicle (metal) body.

⑧ Black

Cord installation (Fig. 15)

① Clamps

② Rear view camera

③ RCA power supply cable

④ Product with a video input jack

(Hideaway unit etc.)

⑤ Power supply unit

⑥ Made with a rasp etc.

⑦ Scuff plate

⑧ Clamp

⑨ Waterproof plate

Cord installation points (Fig. 16)

• When pulling the cord out of the car,

pull from the outer side of the hatch har-

ness cover and hinge.

① Pull out from here

② Hinge

③ Harness cover

④ Rear view camera

⑤ Hatch

After cord installation (Fig. 17, Fig. 18)

• Open and close the hatch door slowly

to confirm that the cord is not rubbing

against the rim of the door.

① Rear view camera

② Hatch

③ Cord

• When the rear view camera cord cannot

be pulled out from the lower side due to

the type of car.

As shown in the figure 18, bend the cord

into a U shape in front of the waterproof

pad, making sure that rain water cannot

enter the car by running down the cord.

① Clamps

② Waterproof pad

③ Rubber packing

④ Make a U-shaped loop in the lead outside

the rubber packing to prevent rainwater from

flowing along the lead into the interior of the

vehicle.

Power source ........................................... 14.4 V DC

(10.8 V to 15.1 V allowable)

Grounding system .............................. Negative type

Max. current consumption .......................... 120 mA

Output video ....................................... Mirror image

(for rear view confirmation)

Sensor ............................ 1/4-inch color CCD sensor

No. of pixels ........ 492 (vertical) × 512 (horizontal)

(Total no. of pixels: 270 000,

effective no. of pixels roughly 250 000)

Lens ........................................................ Wide-angle,

focal length f = 1.53 mm, F value 2.8

Angle of view ................... Horizontal: approx. 135º

Vertical: approx. 100º

IR cutoff filter (special filter for vehicle mounting)

.................................................................. Provided

Iris system .......................................... Electronic iris

Scanning system ........................................ Interlace

Synchronizing system ....... Internal synchronization

Signal-to-noise ratio .......................... 40 dB or more

(at the recommended intensity of illumination)

Horizontal resolution ............ Approx. 300 TV lines

Illumination range .... Approx. 1.5 lux to 100 000 lux

Image output ...................................... 1 Vp-p (75 Ω)

Operation temperature range ........... –30ºC to +70ºC

+22ºF to +158ºF

Storage temperature range .............. –40ºC to +85ºC

–40ºF to +185ºF

Dimensions

Camera unit ... 27 (W) × 27 (H) × 26 (D) mm

1 (W) × 1 (H) × 1 (D) in.

Power supply unit

.................... 70 (W) × 23 (H) × 35 (D) mm

2-3/4 (W) × 7/8 (H) × 1-3/8 (D) in.

Weight

Camera unit ................................ 150 g (0.3 lbs)

(including the cable)

Power supply unit ...................... 160 g (0.4 lbs)

(including the power cord)

Note:

Specifications and the design are subject to possible

modification without prior notice due to improve-

ments.

Specifications <ENGLISH>

Page is loading ...

Pioneer ND-BC2 User manual

Brand: Pioneer

Model: ND-BC2

Category: Security cameras

Type: User manual

This manual is also suitable for

ND BC2

Download PDF

report

in other languages

italiano: Pioneer ND-BC2 Manuale utente
français: Pioneer ND-BC2 Manuel utilisateur
español: Pioneer ND-BC2 Manual de usuario
Deutsch: Pioneer ND-BC2 Benutzerhandbuch

Pioneer ND-BC2 User manual

This manual is also suitable for

Pioneer ND-BC2 User manual

in other languages

Related papers

Other documents