Makita BDF450 User manual

Cordless Driver Drill

Instruction Manual

Akku-Bohrschrauber

Betriebsanleitung

Akumulatorowa wiertarko-wkrętarka

Instrukcja obsługi

Аккумуляторная дрель шуруповерт

Инструкцию по эксплуатации

BDF440

BDF450

MakitaTool.ru

Page is loading ...

4

ENGLISH

Explanation of general view

SPECIFICATIONS

• Due to our continuing program of research and development, the specifications herein are subject to change without

notice.

• Note: Specifications may differ from country to country.

Symbols

The following show the symbols used for the tool. Be sure

that you understand their meaning before use.

Only for EU countries

Do not dispose of electric equipment together with house-

hold waste material!

In observance of European Directive 2002/96/EC on

waste electrical and electronic equipment and its imple-

mentation in accordance with national law, electric equip-

ment that have reached the end of their life must be

collected separately and returned to an environmentally

compatible recycling facility.

Intended use

The tool is intended for drilling and screw driving in wood,

metal and plastic.

1. Battery cartridge

2. Button

3. Red part

4. Switch trigger

5. Lamp

6. Reversing switch lever

7. Speed change lever

8. Adjusting ring

9. Graduations

10. Pointer

11. Sleeve

12. Screw

13. Hook

14. Groove

15. Limit mark

16. Rear cover

17. Screws

18. Spring

19. Arm

20. Recesed part

21. Carbon brush cap

22. Hole

Model BDF440 BDF450

Capacities

Steel 13 mm

Wood 27 mm

Wood screw ø 6.8 mm x 50 mm

Machine screw M6

No load speed (min

-1

)

High (2) 0 - 1,400

Low (1) 0 - 400

Overall length 186 mm

Net weight 1.6 kg 1.7 kg

Rated voltage D.C. 14.4 V D.C. 18 V

5

GENERAL SAFETY RULES

WARNING:

Read all instructions. Failure to follow all instructions

listed below may result in electric shock, fire and/or seri-

ous injury. The term “power tool” in all of the warnings

listed below refers to your mainsoperated (corded) power

tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

Work area safety

1. Keep work area clean and well lit. Cluttered and

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of flammable liq-

uids, gases or dust. Power tools create sparks which

may ignite the dust or fumes.

3. Keep children and bystanders away while operat-

ing a power tool. Distractions can cause you to lose

control.

Electrical safety

4. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded sur-

faces such as pipes, radiators, ranges and refrig-

erators. There is an increased risk of electric shock if

your body is earthed or grounded.

6. Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the

risk of electric shock.

7. Do not abuse the cord. Never use the cord for car-

rying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk

of electric shock.

8. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of elec-

tric shock.

Personal safety

9. Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

10. Use safety equipment. Always wear eye protec-

tion. Safety equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

11. Avoid accidental starting. Ensure the switch is in

the off-position before plugging in. Carrying power

tools with your finger on the switch or plugging in

power tools that have the switch on invites accidents.

12. Remove any adjusting key or wrench before turn-

ing the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result

in personal injury.

13. Do not overreach. Keep proper footing and bal-

ance at all times. This enables better control of the

power tool in unexpected situations.

14. Dress properly. Do not wear loose clothing or jew-

ellery. Keep your hair, clothing, and gloves away

from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

15. If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of these

devices can reduce dustrelated hazards.

Power tool use and care

16. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

17. Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be con-

trolled with the switch is dangerous and must be

repaired.

18. Disconnect the plug from the power source and/or

the battery pack from the power tool before mak-

ing any adjustments, changing accessories, or

storing power tools. Such preventive safety mea-

sures reduce the risk of starting the power tool acci-

dentally.

19. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users.

20. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tools operation. If damaged, have the power tool

repaired before use. Many accidents are caused by

poorly maintained power tools.

21. Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

22. Use the power tool, accessories and tool bits etc.

in accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions

and the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

Battery tool use and care

23. Ensure the switch is in the off position before

inserting battery pack. Inserting the battery pack into

power tools that have the switch on invites accidents.

24. Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another battery pack.

6

25. Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury and fire.

26. When battery pack is not in use, keep it away from

other metal objects like paper clips, coins, keys,

nails, screws, or other small metal objects that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause

burns or a fire.

27. Under abusive conditions, liquid may be ejected

from the battery, avoid contact. If contact acciden-

tally occurs, flush with water. If liquid contacts

eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns.

Service

28. Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

is maintained.

29. Follow instruction for lubricating and changing

accessories.

30. Keep handles dry, clean and free from oil and

grease.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to drill

safety rules. If you use this power tool unsafely or

incorrectly, you can suffer serious personal injury.

1. Use auxiliary handles supplied with the tool. Loss

of control can cause personal injury.

2. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

3. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high loca-

tions.

4. Hold the tool firmly.

5. Keep hands away from rotating parts.

6. Do not leave the tool running. Operate the tool

only when hand-held.

7. Do not touch the drill bit or the workpiece immedi-

ately after operation; they may be extremely hot

and could burn your skin.

8. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation and

skin contact. Follow material supplier safety data

.

SAVE THESE INSTRUCTIONS

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

IMPORTANT SAFETY

INSTRUCTIONS FOR BATTERY

CARTRIDGE

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an explo-

sion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

6. Do not store the tool and battery cartridge in loca-

tions where the temperature may reach or exceed

50°C (122°F).

7. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

SAVE THESE INSTRUCTIONS

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice less

tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C - 40°C (50°F - 104°F). Let a hot battery

cartridge cool down before charging it.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before adjusting or checking

function on the tool.

Installing or removing battery cartridge

(Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while sliding the button on the side of the cartridge.

7

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red part on

the upper side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not, it

may accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Switch action (Fig. 2)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Lighting up the front lamp (Fig. 3)

CAUTION:

• Do not look in the light or see the source of light

directly.

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The lamp goes out 10 -15 seconds after releasing the trig-

ger.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

Reversing switch action (Fig. 4)

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for counter-

clockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

Speed change (Fig. 5)

To change the speed, first switch off the tool and then

slide the speed change lever to the “2” side for high speed

or “1” side for low speed. Be sure that the speed change

lever is set to the correct position before operation. Use

the right speed for your job.

CAUTION:

• Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change

lever positioned halfway between the “1” side and “2”

side, the tool may be damaged.

• Do not use the speed change lever while the tool is

running. The tool may be damaged.

Adjusting the fastening torque (Fig. 6)

The fastening torque can be adjusted in 17 steps by turn-

ing the adjusting ring so that its graduations are aligned

with the pointer on the tool body. The fastening torque is

minimum when the number 1 is aligned with the pointer,

and maximum when the marking is aligned with the

pointer.

The clutch will slip at various torque levels when set at the

number 1 to 16. The clutch is designed not to slip at the

marking.

Before actual operation, drive a trial screw into your mate-

rial or a piece of duplicate material to determine which

torque level is required for a particular application.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing driver bit or drill bit

(Fig. 7)

Turn the sleeve counterclockwise to open the chuck jaws.

Place the bit in the chuck as far as it will go. Turn the

sleeve clockwise to tighten the chuck.

To remove the bit, turn the sleeve counterclockwise.

Hook (Fig. 8)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool hous-

ing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out.

OPERATION

CAUTION:

• Always insert the battery cartridge all the way until it

locks in place. If you can see the red part on the upper

side of the button, it is not locked completely. Insert it

fully until the red part cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to you or

someone around you.

Screwdriving operation (Fig. 9)

CAUTION:

• Adjust the adjusting ring to the proper torque level for

your work.

Place the point of the driver bit in the screw head and

apply pressure to the tool. Start the tool slowly and then

increase the speed gradually. Release the switch trigger

as soon as the clutch cuts in.

8

CAUTION:

• Make sure that the driver bit is inserted straight in the

screw head, or the screw and/or bit may be damaged.

NOTE:

• When driving wood screws, predrill pilot holes to make

driving easier and to prevent splitting of the workpiece.

See the chart.

Drilling operation

First, turn the adjusting ring so that the pointer points to

the marking. Then proceed as follows.

Drilling in wood

When drilling in wood, the best results are obtained with

wood drills equipped with a guide screw. The guide screw

makes drilling easier by pulling the bit into the workpiece.

Drilling in metal

To prevent the bit from slipping when starting a hole, make

an indentation with a center-punch and hammer at the

point to be drilled. Place the point of the bit in the indenta-

tion and start drilling.

Use a cutting lubricant when drilling metals. The excep-

tions are iron and brass which should be drilled dry.

CAUTION:

• Pressing excessively on the tool will not speed up the

drilling. In fact, this excessive pressure will only serve

to damage the tip of your bit, decrease the tool perfor-

mance and shorten the service life of the tool.

• There is a tremendous force exerted on the tool/bit at

the time of hole break through. Hold the tool firmly and

exert care when the bit begins to break through the

workpiece.

• A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to back

out. However, the tool may back out abruptly if you do

not hold it firmly.

• Always secure small workpieces in a vise or similar

hold-down device.

• If the tool is operated continuously until the battery car-

tridge has discharged, allow the tool to rest for 15 min-

utes before proceeding with a fresh battery.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before attempting to perform

inspection or maintenance.

Replacing carbon brushes

Replace when they wear down to the limit mark. Keep the

carbon brushes clean and free to slip in the holders. Both

carbon brushes should be replaced at the same time. Use

only identical carbon brushes. (Fig. 10)

Use a screwdriver to remove two screws then remove the

rear cover. (Fig. 11)

Raise the arm part of the spring and then place it in the

recessed part of the housing with a slotted bit screwdriver

of slender shaft or the like. (Fig. 12)

Use pliers to remove the carbon brush caps of the carbon

brushes. Take out the worn carbon brushes, insert the

new ones and replace the carbon brush caps in reverse.

(Fig. 13)

Make sure that the carbon brush caps have fit into the

holes in brush holders securely. (Fig. 14)

Reinstall the rear cover and tighten two screws securely.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

Nominal diameter of wood

screw (mm)

Recommended size of pilot

hole (mm)

3.1 2.0 - 2.2

3.5 2.2 - 2.5

3.8 2.5 - 2.8

4.5 2.9 - 3.2

4.8 3.1 - 3.4

5.1 3.3 - 3.6

5.5 3.7 - 3.9

5.8 4.0 - 4.2

6.1 4.2 - 4.4

9

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

• Drill bits

• Screw bits

•Hook

• Various type of Makita genuine batteries and chargers

• Automatic refreshing adapter

• Plastic carrying case

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in

compliance with the following standards of standardized docu-

ments, EN60745, EN55014 in accordance with Council Direc-

tives, 89/336/ EEC, 98/37/EC.

Yasuhiko Kanzaki CE 2005

Director

MAKITA INTERNATIONAL EUROPE LTD.

Michigan Drive, Tongwell, Milton Keynes,

Bucks MK15 8JD, ENGLAND

Responsible manufacturer:

Makita Corporation Anjo Aichi Japan

For European countries only

Noise and Vibration

For Model BDF440

The typical A-weighted sound pressure level is 72 dB (A).

Uncertainty is 3 dB (A).

The noise level under working may exceed 85 dB (A).

– Wear ear protection. –

The typical weighted root mean square acceleration value

is not more than 2.5 m/s

2

.

These values have been obtained according to EN60745.

For Model BDF450

The typical A-weighted sound pressure level is 71 dB (A).

Uncertainty is 3 dB (A).

The noise level under working may exceed 85 dB (A).

– Wear ear protection. –

The typical weighted root mean square acceleration value

is not more than 2.5 m/s

2

.

These values have been obtained according to EN60745.

Page is loading ...

Makita Corporation

Anjo, Aichi, Japan

884631B203

Makita BDF450 User manual

Makita BDF450 User manual

in other languages

Related papers

Other documents