Unique Appliances UGP-120L1 User manual

Brand: Unique Appliances

Model: UGP-120L1

Category: Cool boxes

Type: User manual

Unique Appliances UGP-120L1 is a portable fridge/freezer with a 4.2 cu. ft. capacity, designed for outdoor and camping use. It offers dual insulated compartment lids, a digital control panel, and protective corners for durability. The UGP-120L1 can operate on both AC and DC power, making it suitable for use in vehicles, boats, or at campsites. It features an adjustable temperature range, allowing you to set different temperatures for the left and right compartments. Additionally, the fridge/freezer has a battery management system that protects your vehicle's battery from excessive discharge.

80L / 120L

AC/DC PORTABLE

FRIDGE/FREEZER

OWNER’S GUIDE

80L / 2.8 cu. ft.

UGP-80L1

120L / 4.2 cu. ft.

UGP-120L1

TABLE OF CONTENTS

03 Installation and operation of your Unique portable AC/DC

fridge/freezer

04 Defrosting the cabinet

05 UGP-80L Portable fridge/freezer: features

06 UGP-120L Portable fridge/freezer: features

07 Power requirements

07 Using the connection guards

07 AC power connection

08 DC power connection

08 Replacing the fuse

09 Temperature settings and LCD display

11 12/24V DC battery management settings

13 Connecting to a battery

13 Using solar panels

14 Using portable generators

15 Tips and suggestions

16 Technical speciﬁcations

17 Troubleshooting

18 Appliance information

18 Notes

19 Contact us

19 Limited warranty

INSTALLATION AND OPERATION OF

YOUR UNIQUE PORTABLE AC/DC

FRIDGE/FREEZER

It is important that your fridge/

freezer is installed and oper-

ated in accordance with the

manufacturer’s instructions to

guarantee the performance,

efﬁciency and operation.

• Position the fridge/freezer in

a safe and secure location, out

of the reach of rain/snow and

excessive wind. Prolonged

exposure to heat sources or

direct sunlight can aect the

unit’s performance and e-

ciency.

• The normal operation of the fridge/freezer requires heat to be radi-

ated away from the condensers located in the end of the cabinet.

Ensure the vented areas of the cabinet are kept clear at all times to

allow adequate airﬂow to the compressor.

• The cooling system has been

designed to continue operat-

ing correctly when the fridge/

freezer is positioned on angles

up to 35˚. It is recommended

that the time the unit is ex-

posed to angles over 30˚ is

limited to no more than four

(4) hours continuous opera-

tion.

IMPORTANT: After transit where the fridge/freezer is on

its side or back, ensure fridge/freezer is in a level, up-

right position for 3-4 hours to allow compressor ﬂuids

to redistribute evenly before use.

DEFROSTING THE CABINET

If your appliance is being used primarily as a freezer, it is possible

that an ice build-up on the interior may occur. This build up can af-

fect the performance and eciency of the cooling system and must

be removed.

Do not use pointed tools, knives or sharp utensils, or signiﬁcant force

to remove the ice as this may result in damage to the unit. Turn the

fridge/freezer o and empty the cabinet of food/drinks. Allow the

ice to melt and then drain the water from the cabinet. Use a soft,

clean cloth to wipe down all surfaces and allow the fridge/freezer to

dry completely.

IMPORTANT

This fridge/freezer is not intended for use by children or persons

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they are under supervision or

instruction concerning the use of the fridge/freezer by a person

responsible for their safety.

• This is not a toy. Do not allow children to play with or within the

fridge/freezer.

• The fridge/freezer is suitable for outdoor and camping use and

should not be exposed to rain or snow or other inclement weather.

INSTALLATION AND OPERATION OF

YOUR UNIQUE PORTABLE AC/DC

FRIDGE/FREEZER continued

UGP-80L PORTABLE

FRIDGE/FREEZER FEATURES

Powder coated

steel exterior

Stainless steel lid

latches

Sturdy side handles

Digital control panel

Protective corners

Protective insulated

cover

Wireless

remote

DC power cord

with 10 amp fuse

Battery alligator

clips

AC power cord

Interior insulated

compartment lids

UGP-120L PORTABLE

FRIDGE/FREEZER FEATURES

Dual insulated

compartment lids

Powder coated

steel exterior

Stainless steel lid

latches

Sturdy side

handles

Digital control

panel

Protective

corners

Internal LED light

Protective insulated cover

Wireless

remote

DC power cord

with 10 amp fuse

Battery alligator

clips

AC power cord

POWER REQUIREMENTS

The Unique UGP-80L and UGP-120L portable fridge/freezers are

designed to operate on AC and DC voltage inputs.

AC input Voltage is required to be 110V AC at 50 - 60 Hz

DC input Voltage is require to be 12 or 24 DC +/- 10%

Velcro connection guards on

either end of the DC power cord

and the battery alligator clips or

AC power cord.

Velcro connection guards

wrapped around each other to

secure connection.

AC POWER CONNECTION

USING THE VELCRO

CONNECTION GUARDS

The Unique UGP-80L and UGP-120L portable fridge/freezers are

supplied with an approved 2 pin AC power cord. It is recommended

that this cord is not lengthened as this may result in a voltage drop

and reduced performance.

To ensure a secure connection between the DC power cord and the

battery alligator clips or AC power cord, the ends of the Unique

UGP-80L and UGP-120L power cords are supplied with velcro con-

nection guards.

• Insert DC power cord (cigarette lighter end) into the female end of

the battery alligator clip or AC power cord.

• Wrap the velcro ties from either cord end around each other to

ensure a secure connection and no loss of power.

DC POWER CONNECTION

REPLACING THE FUSE

2-3

4-5

The Unique UGP-80L and UGP-120L portable fridge/freezers are

supplied with a vehicle DC plug (cigarette lighter plug). It is recom-

mended that this cord is not lengthened as this may result in a volt-

age drop and reduced performance.

When connecting the fridge/freezer to DC, plug the power cord into

the DC socket on the fridge/freezer and then plug the other end of

the power cord into the DC supply.

The supplied DC power cord comes with an in-line fuse. If the red

indicator light on the DC cigarette plug is not illuminated, there is

either no DC voltage being supplied or the fuse is blown. See below

for fuse replacement instructions.

*Only use the DC power cord that is supplied with the fridge/freezer.

The Unique UGP-80L and UGP-120L portable fridge/freezers are

supplied with 2 additional replacement 10A fuses. These can be

found in a plastic bag attached to the cord. If the indicator light on

the DC power cord is not illuminated, it could mean that the fuse has

blown. Here is how to replace the fuse:

1. Unscrew the black

plastic end cap from

the DC power plug.

2. Unscrew the metal

threaded tip of the DC

power plug to expose

the cylindrical 10 amp

fuse.

3. Remove blown fuse and

replace with a new fuse.

4. Replace metal threaded

tip of DC power plug and

screw back into place.

5. Replace black plastic

end cap of the DC power

plug and screw into

place.

Black plastic end cap

Metal threaded tip

10 A fuse

TEMPERATURE SETTINGS

AND LCD DISPLAY

Both the fridge/freezer control panel and the wireless remote read-

out display the following information:

• the current set temperature

• the actual internal cabinet temperature

• the supply voltage at the inlet connection to the fridge/freezer

Follow the same steps when using either the on the fridge/freezer

control panel or the wireless remote read-out.

To use the wireless remote, simply plug it in to a suitable 12V DC

(cigarette lighter plug) and within 5 to 10 seconds it will connect to

the fridge and will display the same information as per the display

on the fridge.

Battery monitor

voltage setting

Fan symbol spins

when compressor

is running

Cabinet temperature

settings

Snowﬂake symbol indicates

compressor is in maximum

speed mode

(NOT RECOMMENDED FOR

SOLAR AND BATTERY USE)

Battery

symbol

ﬂashes

when the

battery

monitor is

activated

TO SET THE TEMPERATURE

IN THE LEFT CHAMBER

STEP 1

Push the SET button once, the

digital display on the left will

start to ﬂash with the tempera-

ture that the control is currently

set to.

STEP 2

To change the setting push the

UP or DOWN button until you

reach the desired temperature.

The display will ﬂash several

times before returning to the

current cabinet temperature.

To change the temperature

setting repeat steps 1 and 2.

TO SET THE TEMPERATURE

IN THE RIGHT CHAMBER

STEP 1

Push the SET button twice, the

digital display on the right will

start to ﬂash with the tempera-

ture that the control is currently

set to.

STEP 2

To change the setting push the

UP or DOWN button until you

reach the desired tempera-

ture. The display will ﬂash sev-

eral times and then stop on the

temperature you have set. The

display will ﬂash several times

before returning to the current

cabinet temperature.

To change the temperature

setting repeat steps 1 and 2.

TEMPERATURE SETTINGS

AND LCD DISPLAY

continued

NOTE

The fridge/freezer will automatically start to operate after 2-3 min-

utes when the DC input power source is connected.

12/24V DC BATTERY MANAGEMENT

SETTINGS

The Unique UGP-80L and UGP-120L portable fridge/freezers are

equipped with a multi-level INPUT VOLTAGE battery setting that

protects your vehicle battery from excessive discharge (draining)

when the fridge/freezer is connected to the 12V/24V DC input power

source.

As the fridge/freezer is operating, if the power source voltage falls

below the set battery voltage level, it will automatically switch o

and an audible beeping will be heard. This may occur in a vehicle

when the ignition is switched o.

The fridge/freezer will automatically switch back on once the vehicle

has been restarted and the battery has been recharged to above the

cut-in level of the set battery voltage.

IMPORTANT

It is recommended to set the INPUT BATTERY VOLTAGE to 10.9V

when using the fridge/freezer with 12V DC input power source.

The battery monitor can be set between a maximum of 11.5V and a

minimum of 10.0V

STEP 1

Push the SET button and hold until

the Battery Voltage Setting ﬂashes.

STEP 2

To change the setting push the UP

or DOWN button until you reach the

desired voltage setting.

After selecting the desired Battery Voltage Setting, the display will

return to the current input voltage reading after 10 seconds.

To change the set voltage again, repeat steps 1 and 2.

When the battery voltage reaches the level selected an audible

BEEP will be heard and a battery symbol will start to ﬂash on the

display.

To reset the battery monitor, discon-

nect the 12V supply to the fridge

and then wait until the battery volt-

age increase above the set level,

then reconnect the 12V and rest the

require temperature.

12/24V DC BATTERY MANAGEMENT

SETTINGS

continued

EXPRESS COOL DOWN

(not recommended for solar/battery use)

The Unique UGP-80L and UGP-120L portable fridge/freezers are

equipped with a multi-level compressor speed function that allows

the compressor speed to increase when faster cabinet cool down

times are required.

Press and hold the DOWN button for 2 seconds to enter the high

speed mode. A snowﬂake icon will appear in the top right hand cor-

ner of the display to conﬁrm the compressor is operating at maxi-

mum speed.

To reset the fridge/freezer to its normal speed, press the UP button

for 2 seconds, the snowﬂake icon will disappear and the compressor

will enter its normal speed mode.

ECONOMY: (Compressor Speed

Slow) This mode reduces power

consumption and is used in the

normal cooling function.

MAXIMUM: (Compressor Speed

Fast) Used to cool down the in-

ternal cabinet temperature of the

fridge rapidly, however this mode

will consume more power.

TURNING OFF A COMPARTMENT

Each compartment of the Unique UGP-80L and UGP-120L portable

fridge/freezers can be turned o when not in use to save energy.

To turn off the temperature in the left compartment:

Push the SET button once. The digital display on the LEFT will start

to ﬂash with the temperature. Push the UP or DOWN button to set

the temperature to either -19˚ or +20 (whichever is closest, depend-

ing on the starting temperature.) The LEFT side of the digital read-

out will then show ”- - “, push the SET button to conﬁrm

To turn off the temperature in the right compartment:

Push the SET button twice. The digital display on the RIGHT will

start to ﬂash with the temperature. Push the UP or DOWN button to

set the temperature to either -19˚ or +20 (whichever is closest, de-

pending on the starting temperature.) The RIGHT side of the digital

readout will then show ”- - “, push the SET button to conﬁrm.

USING SOLAR PANELS

The power consumption and eciency of your Unique UGP-80L and

UGP-120L portable fridge/freezer makes it ideal to be used in con-

junction with solar panels to provide recharging of the DC supply.

The Unique Portable Solar Panel system (UGP-100WSP) was

designed for easy use with the fridge/freezer’s DC supply.

Solar panels will provide charge into the battery during the daylight

hours even while the appliance is operating.

As the output from solar panels changes depending on the level of

sunlight and intensity, your UGP-80L/UGP-120L portable fridge/

freezer cannot be connected directly to the solar panels. The appli-

ance must be connected to a suitable DC battery and then the solar

panels connected to the battery.

OR OR

CONNECTING TO A BATTERY

Your DC fridge/freezer can run o a single 12V or 24V power supply.

When connecting to a 12V battery, ensure that the supplied connec-

tion wires are used. Connect the positive wire (red) to the positive

terminal on the battery and the negative wire (black) to the negative

terminal on the battery. Please ensure that your deep cycle battery

is fully charged and is properly connected to the Unique Portable

Solar Panel system (UGP-100WSP) or a power generator.

USING PORTABLE GENERATORS

It is important that the correct generator is used with your UGP-

80L/UGP-120L portable fridge/freezer. An incorrect generator may

result in reduced performance or damage to your appliance which

may void your appliance’s warranty.

If connecting directly to an AC generator, ensure that only a digital

or inverter type generator is used. These provide a more reliable

and constant 110V AC output and are speciﬁcally designed to power

electronic and other power sensitive appliances.

When charging the battery using a digital or inverter type genera-

tor, we recommend only using a ‘smart battery charger’ that is fully

automatic, spark proof and reverse polarity protected. The battery

charger is connected directly to the AC power output of the genera-

tor.

TIPS AND SUGGESTIONS

• Fresh and frozen foods should not be stored together. Frozen

surfaces can cause frost damage on fresh foods which can then

lead to spoilage. It is best to put an insulating layer between these

goods or to organize them into separate compartments.

• When the appliance is being set at 0˚C / 32˚F or lower, do not

store glass bottles or liquids such as beer, wine, juices or soft

drinks in the unit as they may freeze and shatter.

• Items such as fruit and vegetables should be stored closer to the

top of the cabinet as this area is normally slightly warmer. This will

reduce the risk of spoiling and ensure that delicate fresh foods are

not crushed by heavier frozen items.

• To improve the eciency of your UGP-80L/UGP-120L portable

fridge/freezer it is better to have the cabinet as full as possible at

all times. A full cabinet will provide lower power consumption over

24 hours than a half-empty one, as chilled and frozen food help

maintain temperature eciency.

• Make your selection of what you wish to remove from the cabinet

before you open the door. This will reduce the amount of warm air

that will enter the cabinet while the door is open, and help main-

tain energy and temperature eciency.

• When located in the rear of a vehicle, it is recommended that the

fridge/freezer be shaded from direct sunlight to reduce the risk of

increased heat. It should also be provided with suitable ventilation

to guarantee ecient power consumption and performance.

Remember: when a vehicle is parked in the sun on a day where

the ambient temperature is +30˚C/86˚F, the interior of the vehicle

can reach more than +55˚C/131˚F.

TECHNICAL SPECIFICATIONS

MODEL UGP-80L UGP-120L

GROSS CAPACITY

80 L / 2.8 cubic feet 120 L / 4.2 cubic feet

ZONE

Dual Dual

RUN TEMPERATURE

-18˚C/-1˚F to +20˚C/68˚F

(in ambient temperature

between +1˚C/34˚F to

+43˚C/109˚F)

-18˚C/-1˚F to +20˚C/68˚F

(in ambient temperature

between +1˚C/34˚F to

+43˚C/109˚F)

POWER CONSUMPTION

33 W

(power consumption varies

based on temp. setting)

33 W (power consumption varies

based on temp. setting)

AVERAGE RUN CURRENT

2.7 amps on 12V DC 2.7 amps on 12V DC

TOTAL WATT HR DRAW

464 Wh/24 hrs (lrg. side set to

+5˚C/Sm. side set to -13˚C)

469 Wh/24 hrs (lrg. side set to

+5˚C/Sm. side set to -13˚C)

TOTAL AMP HR DRAW

38 Ah/24 hrs (lrg. side set to +5˚C/

Sm. side set to -13˚C)

30 Ah/24 hrs (lrg. side set to +5˚C/

Sm. side set to -13˚C)

REFRIGERANT

R134a / 80g R134a / 110g

INSULATION MATERIAL

High pressure foaming 141b High pressure foaming 141b

INSULATION THICKNESS

Wall: 40mm / Lid: 50mm Wall: 40mm / Lid: 50mm

NET WEIGHT (kg, approx.)

31 kg / 68.3 lbs 36 kg/79.3 lbs

EXTERNAL DIMENSION

(WxDxH)

27” x 19” x 24.4”

69 cm x 49 cm x 62 cm

34” x 21” x 28.3”

86.5 cm x 53.5 cm x 72 cm

INTERNAL DIMENSION -

large chamber (LxWxD)

13.3” x 12.4” x 19”

33.7 cm x 31.5 cm x 48.5 cm

15.3” x 12.4” x 22.8”

39 cm x 31.5 cm x 58 cm

INTERNAL DIMENSION -

small chamber (LxWxD)

13.3” x 8.1” x 11”

33.7 cm x 20.6 cm x 28 cm

15.3” x 12.4” x 14.5”

39 cm x 31.5 cm x 37 cm

TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

THE COMPRESSOR DOES

NOT RUN

The polarity of the positive and the

negative have been reversed.

Switch off the power and check the

polarity of the connections.

Check your in-line fuse within the

cigarette lighter plug.

The voltage is insufﬁcient or

interrupted.

Switch off power.

Check connections and then fuses.

THE COMPRESSOR RUNS

FOR 1-5 MINUTES AND

THEN STOPS

The voltage is insufﬁcient or

interrupted.

Switch off power.

Check connections and then restart.

THE COMPRESSOR

RUNS BUT THE INNER

COMPARTMENT DOES NOT

GET COLD

The refrigeration system may be

blocked.

Contact your dealer for assistance.

THE INNER LINER IS

VERY COLD AND THE

COMPRESSOR RUNS

CONTINUOUSLY

There is a build up of ice on the

inner liner.

Defrost the cabinet.

The lid is being opened and closed

too frequently.

The lid should only be opened when

needed.

The cabinet is being overloaded and

used as a freezer.

Remove some product.

There is insufﬁcient air ﬂow to the

condenser.

Select a well ventilated area.

THE WIRELESS REMOTE

DOES NOT CONNECT TO THE

FRIDGE

The voltage is insufﬁcient or

interrupted.

Switch off power. Check connections

and then fuses. Restart.

The fridge is not switched on. Turn fridge on.

NOTES

APPLIANCE INFORMATION

(manual copy - keep with your records)

To make care and servicing of your fridge/freezer easy and ecient, please

record the following information for future reference:

Model:

Serial Number:

Purchased From:

Date Purchased:

UGP-80L/UGP-120L PORTABLE

FRIDGE/FREEZER

1 YEAR LIMITED WARRANTY

Unique Gas Products Ltd., warrants that this portable fridge/freezer is free from defects in material and

workmanship under normal usage and service under the following terms:

1. This Warranty is made only to the ﬁrst purchaser (“original purchaser”) who acquires this fridge/freezer

for his/her own use and will be honored by Unique Gas Products Ltd. and by the Seller.

2. Any part of this fridge/freezer returned to the Seller or Unique Gas Products Ltd., which upon examina-

tion is determined by them to have been defective in material or workmanship, will at their option

be either repaired or replaced under this warranty, within 14 days from date of return to Unique Gas

Products Ltd., without charge for materials/parts.

3. The obligation to repair or replace defective parts will apply only to parts returned within one year of the

date of purchase and will constitute the Sellers sole obligation under this Warranty.

The Seller will have no obligation under this warranty with respect to conditions unrelated to the material

or workmanship of this fridge/freezer. Such unrelated conditions include without limitation:

a) damage to any part of this fridge/freezer caused by misuse, neglect of service or any alteration thereof.

b) use of this product for any purpose other than its Intended use.

This Unique fridge/freezer must be maintained regularly as outlined in the Owner’s Manual. Unique Gas

Products Ltd. and the seller will not be liable for direct or indirect loss of foods caused by failure in opera-

tion. In case of failure, the owner must provide proof of purchase, model, and serial number to the seller or

Unique Gas Products Ltd.

Please ﬁll out warranty card within 30 days and mail back to Unique for warranty coverage.

For questions related to the operation, safety or the purchase of your fridge/freezer, please contact

your dealer for more information. For general information, contact our customer service department:

• Toll-free: 1-877-427-2266 or 1-905-827-6154 (available during regular business hours, 8:30 am to

4:30 pm, EST.

• Email: [email protected]om

Please visit our website for more quality off-grid products:

www.uniqueoffgrid.com

Unique Gas Products Ltd., 2245 Wyecroft Road, Oakville, Ontario, Canada, L6L 5L7

L6L 5L7

www.uniqueogrid.com

Unique Appliances UGP-120L1 User manual

Brand: Unique Appliances

Model: UGP-120L1

Category: Cool boxes

Type: User manual

Download PDF

report

Unique Appliances UGP-120L1 User manual

Unique Appliances UGP-120L1 User manual

Related papers

Other documents