Dell Latitude E7240 Ultrabook Owner's manual

Dell Latitude E7240

Owner's Manual

Regulatory Model: P22S

Regulatory Type: P22S001

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell

™

and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2015 -11

Rev. A04

Contents

1 Working on Your Computer................................................................................5

Before Working Inside Your Computer................................................................................................ 5

Turning Off Your Computer..................................................................................................................6

After Working Inside Your Computer................................................................................................... 7

2 Docking Your Computer..................................................................................... 8

3 Removing and Installing Components............................................................. 9

Recommended Tools............................................................................................................................9

System Overview...................................................................................................................................9

Removing the SD Card........................................................................................................................10

Installing the SD Card.......................................................................................................................... 11

Removing the Battery.......................................................................................................................... 11

Installing the Battery............................................................................................................................12

Removing the Base Cover...................................................................................................................12

Installing the Base Cover.....................................................................................................................14

Removing the mSATA SSD card..........................................................................................................14

Installing the mSATA SSD card............................................................................................................14

Removing the Keyboard Trim............................................................................................................. 14

Installing the Keyboard Trim............................................................................................................... 15

Removing the Keyboard......................................................................................................................15

Installing the Keyboard........................................................................................................................16

Removing the Palmrest.......................................................................................................................16

Installing the Palmrest......................................................................................................................... 17

Removing the Wi‐Fi Switch Board.......................................................................................................17

Installing the Wi‐Fi Switch Board........................................................................................................ 18

Removing the Memory Module.......................................................................................................... 18

Installing the Memory Module............................................................................................................ 19

Removing the WLAN Card.................................................................................................................. 19

Installing the WLAN Card.................................................................................................................... 19

Removing the WWAN Card.................................................................................................................19

Installing the WWAN Card.................................................................................................................. 20

Removing the Display Bezel...............................................................................................................20

Installing the Display Bezel..................................................................................................................21

Removing the Display Panel................................................................................................................21

Installing the Display Panel................................................................................................................. 22

Removing the Coin-Cell Battery........................................................................................................ 22

Installing the Coin-Cell Battery.......................................................................................................... 22

3

Removing the Speakers...................................................................................................................... 23

Installing the Speakers........................................................................................................................ 23

Removing the Display-Hinge Cover...................................................................................................24

Installing the Display-Hinge Cover.....................................................................................................24

Removing the Heatsink.......................................................................................................................24

Installing the Heatsink.........................................................................................................................25

Removing the Display Assembly.........................................................................................................25

Installing the Display Assembly...........................................................................................................27

Removing the System Fan...................................................................................................................27

Installing the System Fan.................................................................................................................... 28

Removing the System Board.............................................................................................................. 28

Installing the System Board................................................................................................................ 29

Removing the Power Connector ...................................................................................................... 30

Installing the Power Connector......................................................................................................... 30

4 Docking Port Information.................................................................................31

5 System Setup....................................................................................................... 32

Boot Sequence....................................................................................................................................32

Navigation Keys................................................................................................................................... 32

System Setup Options.........................................................................................................................33

Updating the BIOS ..............................................................................................................................42

System and Setup Password...............................................................................................................43

Assigning a System Password and Setup Password.................................................................... 43

Deleting or Changing an Existing System and/or Setup Password............................................ 44

6 Diagnostics.......................................................................................................... 45

Enhanced Pre-Boot System Assessment (ePSA) Diagnostics........................................................... 45

Device Status Lights............................................................................................................................46

Battery Status Lights............................................................................................................................46

7 Specifications...................................................................................................... 48

8 Contacting Dell...................................................................................................53

4

1

Working on Your Computer

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to

ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes

that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal

procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you

finish working inside the computer, replace all covers, panels, and screws before connecting to

the power source.

WARNING: Before working inside your computer, read the safety information that shipped with

your computer. For additional safety best practices information, see the Regulatory Compliance

Homepage at

www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface, such as a connector on the back of the

computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts

on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a

processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable

itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,

ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in

this document.

To avoid damaging your computer, perform the following steps before you begin working inside the

computer.

1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

2. Turn off your computer (see Turning off Your Computer).

5

3. If the computer is connected to a docking device (docked), undock it.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and

then unplug the cable from the network device.

4. Disconnect all network cables from the computer.

5. Disconnect your computer and all attached devices from their electrical outlets.

6. Close the display and turn the computer upside-down on a flat work surface.

NOTE: To avoid damaging the system board, you must remove the main battery before you

service the computer.

7. Remove the main battery.

8. Turn the computer top-side up.

9. Open the display.

10. Press the power button to ground the system board.

CAUTION: To guard against electrical shock, always unplug your computer from the

electrical outlet before opening the display.

CAUTION: Before touching anything inside your computer, ground yourself by touching an

unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could

harm internal components.

11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.

Turning Off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before

you turn off your computer.

1. Shut down the operating system:

• In Windows 8:

– Using a touch-enabled device:

a. Swipe in from the right edge of the screen, opening the Charms menu and select

Settings.

b. Select the and then select Shut down

– Using a mouse:

a. Point to upper-right corner of the screen and click Settings.

b. Click the and select Shut down.

• In Windows 7:

1. Click Start .

2. Click Shut Down.

or

1. Click Start .

6

2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click

Shut Down..

2. Ensure that the computer and all attached devices are turned off. If your computer and attached

devices did not automatically turn off when you shut down your operating system, press and hold

the power button for about 4 seconds to turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and

cables before turning on your computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular

Dell computer. Do not use batteries designed for other Dell computers.

1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as

an ExpressCard.

2. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then

plug it into the computer.

3. Replace the battery.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

7

2

Docking Your Computer

Follow the steps to dock your computer:

a. Place the docking spacer until the docking spacer clicks on its place in the docking station.

b. Place the computer on the docking spacer to dock your computer.

NOTE: This docking spacer can be used to dock only the Latitude E7240 / Latitude E7440

computers. You cannot dock any other Dell computers using this docking station.

8

3

Removing and Installing Components

This section provides detailed information on how to remove or install the components from your

computer.

Recommended Tools

The procedures in this document may require the following tools:

• Small flat-blade screwdriver

• Phillips screwdriver

• Small plastic scribe

System Overview

Figure 1. Inside View — Back

1. system fan

2. mSATA card

3. battery bay

9

4. SD card

5. WLAN card

6. WWAN card

7. memory module

8. heatsink

Figure 2. Inside view — Front

1. coin-cell battery 2. SIM card board

3. speaker 4. system board

5. wi-fi switch board 6. system fan

7. display assembly

Removing the SD Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Press in on the SD card to release it from the computer.

3. Slide the SD card out of the computer.

10

Installing the SD Card

1. Slide the SD card into its slot until it clicks into place.

2. Follow the procedures in After Working Inside Your Computer.

Removing the Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Slide the release latch to unlock the battery.

3. Lift the battery from the computer.

11

Installing the Battery

1. Slide the battery into its slot until it clicks into place.

2. Follow the procedures in After Working Inside Your Computer.

Removing the Base Cover

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove battery.

3. Remove the screws that secure the base cover to the computer.

12

4. Lift the base cover to remove it from the computer.

13

Installing the Base Cover

1. Place the base cover to align with the screw holes correctly on the computer.

2. Tighten the screws to secure the base cover to the computer.

3. Install battery.

4. Follow the procedures in After Working Inside Your Computer.

Removing the mSATA SSD card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. To remove the mSATA SSD card:

a. Remove the screw that secures the mSATA SSD card to the computer.

b. Disconnect the mSATA SSD card from the connector on the system board.

Installing the mSATA SSD card

1. Connect the mSATA SSD card to the connector on the system board.

2. Tighten the screw to secure the mSATA SSD to the computer.

3. Install:

a. base cover

b. battery

4. Follow the procedures in After Working Inside Your computer.

Removing the Keyboard Trim

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove battery.

3. Using a plastic scribe, pry the keyboard trim to release it from the computer. Lift up to remove the

keyboard trim from the computer.

14

Installing the Keyboard Trim

1. Align the keyboard trim to its slot.

2. Press along the sides of the keyboard trim until it clicks in place.

3. Install battery.

4. Follow the procedures in After Working Inside Your Computer.

Removing the Keyboard

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

c. keyboard trim

3. Lift the battery bay and remove the screw that secures the keyboard to the computer.

4. Perform the following steps as shown in the illustration:

a. Lift the latch that secure the keyboard cable to the computer [1].

b. Disconnect the keyboard cable the computer [2].

5. Flip the computer and remove the screws that secure the keyboard to the computer.

6. Perform the following steps as shown in the illustration:

a. Slide the keyboard from the computer [1].

b. Lift the keyboard from the computer [2].

15

Installing the Keyboard

1. Connect the keyboard cable and tighten the screw that secures the keyboard to the computer.

2. Slide the keyboard into its compartment and ensure that it clicks into place.

3. Flip the computer, place the keyboard, and tighten the screws that secure the keyboard to the

computer.

4. Install:

a. keyboard trim

b. base cover

c. battery

5. Follow the procedures in After Working Inside Your Computer.

Removing the Palmrest

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. SD card

b. battery

c. base cover

d. keyboard trim

e. keyboard

3. Remove the screws that secure the palmrest assembly and flip the computer.

4. Perform the following steps as shown in the illustration:

a. Disconnect the cable from the computer.

b. Lift the latch that secures the keyboard cable to the computer [1].

c. Disconnect the keyboard cable [2].

d. Disconnect the touch cable from the computer [3].

e. Unroute the cables from the slot [4].

16

5. Remove the screws that secure the palmrest assembly to the front of the computer. Pry the edges

and lift the palmrest assembly from the computer.

Installing the Palmrest

1. Align the palm rest assembly to its original position in the computer and snap it into place.

2. Tighten the screws to secure the palmrest assembly to the front of the computer.

3. Route the touch cable and connect to the system board.

4. Tighten the screws that secure the palmrest assembly to the base of the computer.

5. Install:

a. keyboard

b. keyboard trim

c. base cover

d. battery

e. SD card

6. Follow the procedures in After Working Inside Your Computer.

Removing the Wi‐Fi Switch Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. SD card

b. battery

17

c. base cover

d. keyboard trim

e. keyboard

f. palmrest

3. Disconnect the wi-fi switch board cable from the system board and remove the screw that secures

the wi-fi swtich board to the computer. Remove the wi-fi switch board.

Installing the Wi‐Fi Switch Board

1. Insert the wi-fi switch board in its slot.

2. Connect the wi-fi switch board to the system board.

3. Tighten the screw that secures the wi-fi switch board to the system board.

4. Install:

a. palmrest

b. keyboard

c. keyboard trim

d. base cover

e. battery

f. SD card

5. Follow the procedures in After Working Inside Your Computer.

Removing the Memory Module

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Pry the securing clips away from the memory module until it pops up. Remove the memory module

from its connector on the system board.

18

Installing the Memory Module

1. Insert the memory module into the socket.

2. Press the retention clips to secure the memory module to the system board.

3. Install:

a. base cover

b. battery

4. Follow the procedures in After Working Inside Your Computer.

Removing the WLAN Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. base cover

3. Disconnect the antenna cables from the WLAN card and remove the screw that secures the WLAN

card to the computer. Remove the WLAN card from the computer.

Installing the WLAN Card

1. Insert the WLAN card into its connector at a 45–degree angle into its slot.

2. Tighten the screw to secure the WLAN card to the computer.

3. Connect the antenna cables to their respective connectors marked on the WLAN card.

4. Install:

a. base cover

b. battery

5. Follow the procedures in After Working Inside Your Computer.

Removing the WWAN Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

19

b. SD card

c. base cover

3. Disconnect the antenna cables from the WWAN card.

4. Remove the screw that secures the WWAN card to the computer.

5. Disconnect the antenna cables from the WWAN card. Remove the screw that secures the WWAN

card to the computer and remove it.

Installing the WWAN Card

1. Place the WWAN card in its slot in the system board.

2. Press the WWAN card down and tighten the screw to secure the WWAN card to the computer.

3. Connect the antenna cables to their respective connectors marked on the WWAN card.

4. Install:

a. base cover

b. SD card

c. battery

5. Follow the procedures in After Working Inside Your Computer.

Removing the Display Bezel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the battery.

3. Pry the edges of the display bezel. Remove the display bezel from the display assembly.

20

Page is loading ...

Dell Latitude E7240 Ultrabook Owner's manual

Dell Latitude E7240 Ultrabook Owner's manual

Related papers

Other documents