Genius ROLL UP 45 S Operating instructions

Page is loading ...

ITALIANO

AVVERTENZE PER L’INSTALLATORE

OBBLIGHI GENERALI PER LA SICUREZZA

ATTENZIONE! È importante per la sicurezza delle persone seguire atten-

tamente tutta l’istruzione. Una errata installazione o un errato uso del

prodotto può portare a gravi danni alle persone.

Leggere attentamente le istruzioni prima di iniziare l’installazione del prodot-

to.

I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere lasciati

alla portata dei bambini in quanto potenziali fonti di pericolo.

Conservare le istruzioni per riferimenti futuri.

Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo

indicato in questa documentazione. Qualsiasi altro utilizzo non espressamente

indicato potrebbe pregiudicare l’integrità del prodotto e/o rappresentare

fonte di pericolo.

GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso

da quello per cui l’automatismo è destinato.

Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi

infiammabili costituisce un grave pericolo per la sicurezza.

GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella costru-

zione delle chiusure da motorizzare, nonché delle deformazioni che dovessero

intervenire nell’utilizzo.

Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione

elettrica e scollegare le batterie.

Prevedere sulla rete di alimentazione dell’automazione un interruttore onni-

polare con distanza d’apertura dei contatti uguale o superiore a 3 mm. È

consigliabile l’uso di un magnetotermico da 6A con interruzione onnipolare.

Verificare che a monte dell’impianto vi sia un interruttore differenziale con

soglia da 0,03 A.

GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funziona-

mento dell’automazione, in caso vengano utilizzati componenti dell’impianto

non di produzione GENIUS.

Per la manutenzione utilizzare esclusivamente parti originali GENIUS.

Non eseguire alcuna modifica sui componenti facenti parte del sistema

d’automazione.

L’installatore deve fornire tutte le informazioni relative al funzionamento ma-

nuale del sistema in caso di emergenza e consegnare all’Utente utilizzatore

dell’impianto il libretto d’avvertenze allegato al prodotto.

Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto

durante il funzionamento.

Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro datore

di impulso, per evitare che l’automazione possa essere azionata involonta-

riamente.

L’applicazione non può essere utilizzata da bambini, da persone con ridotte

capacità fisiche, mentali, sensoriali o da persone prive di esperienza o del

necessario addestramento.

L’utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o

d’intervento e deve rivolgersi solo ed esclusivamente a personale qualificato

GENIUS o centri d’assistenza GENIUS.

L’altezza di installazione minima dell’automazione è 2.5m.

Non collegare assolutamente più motori allo stesso saliscendi.

Non collegare due saliscendi allo stesso motore.

La movimentazione dell’apparecchio deve avvenire sempre a vista.

Tutto quello che non è previsto espressamente in queste istruzioni non è

permesso.

ENGLISH

IMPORTANT NOTICE FOR THE INSTALLER

GENERAL SAFETY REGULATIONS

ATTENTION! To ensure the safety of people, it is important that you read all

the following instructions. Incorrect installation or incorrect use of the

product could cause serious harm to people.

Carefully read the instructions before beginning to install the product.

Do not leave packing materials (plastic, polystyrene, etc.) within reach of

children as such materials are potential sources of danger.

Store these instructions for future reference.

This product was designed and built strictly for the use indicated in this docu-

mentation. Any other use, not expressly indicated here, could compromise the

good condition/operation of the product and/or be a source of danger.

GENIUS declines all liability caused by improper use or use other than that for

which the automated system was intended.

Do not install the equipment in an explosive atmosphere: the presence of

inflammable gas or fumes is a serious danger to safety.

GENIUS is not responsible for failure to observe Good Technique in the con-

struction of the closing elements to be motorised, or for any deformation that

may occur during use.

Before attempting any job on the system, cut out electrical power and di-

sconnect the batteries.

The mains power supply of the automated system must be fitted with an all-

pole switch with contact opening distance of 3mm or greater. Use of a 6A

thermal breaker with all-pole circuit break is recommended.

Make sure that a differential switch with threshold of 0.03 A is fitted upstream

of the system.

GENIUS declines all liability as concerns safety and efficient operation of the au-

tomated system, if system components not produced by GENIUS are used.

For maintenance, strictly use original parts by GENIUS.

Do not in any way modify the components of the automated system.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

The installer shall supply all information concerning manual operation of the

system in case of an emergency, and shall hand over to the user the warnings

handbook supplied with the product.

Do not allow children or adults to stay near the product while it is operating.

Keep remote controls or other pulse generators away from children, to prevent

the automated system from being activated involuntarily.

The application cannot be used by children, by people with reduced physical,

mental, sensorial capacity, or by people without experience or the necessary

training.

The User must not in any way attempt to repair or to take direct action and must

solely contact qualified GENIUS personnel or GENIUS service centres.

The minimum installation height of the automated system is 2.5 m.

Do not, on any account, connect several motors to the same up-and-down

device.

Do not connect two up-and-down devices to the same motor.

The equipment must always be visible when moving.

Anything not expressly specified in these instructions is not permitted.

FRANÇAIS

CONSIGNES POUR L’INSTALLATEUR

RÈGLES DE SÉCURITÉ

ATTENTION! Il est important, pour la sécurité des personnes, de suivre à la

lettre toutes les instructions. Une installation erronée ou un usage erroné

du produit peut entraîner de graves conséquences pour les personnes.

Lire attentivement les instructions avant d’installer le produit.

Les matériaux d’emballage (matière plastique, polystyrène, etc.) ne doivent

pas être laissés à la portée des enfants car ils constituent des sources poten-

tielles de danger.

Conserver les instructions pour les références futures.

Ce produit a été conçu et construit exclusivement pour l’usage indiqué dans

cette documentation. Toute autre utilisation non expressément indiquée

pourrait compromettre l’intégrité du produit et/ou représenter une source

de danger.

GENIUS décline toute responsabilité qui dériverait d’usage impropre ou différent

de celui auquel l’automatisme est destiné.

Ne pas installer l’appareil dans une atmosphère explosive: la présence de gaz

ou de fumées inflammables constitue un grave danger pour la sécurité.

GENIUS n’est pas responsable du non-respect de la Bonne Technique dans la

construction des fermetures à motoriser, ni des déformations qui pourraient

intervenir lors de l’utilisation.

Couper l’alimentation électrique et déconnecter la batterie avant toute

intervention sur l’installation.

Prévoir, sur le secteur d’alimentation de l’automatisme, un interrupteur omni-

polaire avec une distance d’ouverture des contacts égale ou supérieure à 3

mm. On recommande d’utiliser un magnétothermique de 6A avec interruption

omnipolaire.

Vérifier qu’il y ait, en amont de l’installation, un interrupteur différentiel avec

un seuil de 0,03 A.

GENIUS décline toute responsabilité quant à la sécurité et au bon fonctionne-

ment de l’automatisme si les composants utilisés dans l’installation n’appar-

tiennent pas à la production GENIUS.

Utiliser exclusivement, pour l’entretien, des pièces GENIUS originales.

Ne jamais modifier les composants faisant partie du système d’automati-

sme.

L’installateur doit fournir toutes les informations relatives au fonctionnement

manuel du système en cas d’urgence et remettre à l’Usager qui utilise l’instal-

lation les “Instructions pour l’Usager” fournies avec le produit.

Interdire aux enfants ou aux tiers de stationner près du produit durant le fon-

ctionnement.

Eloigner de la portée des enfants les radiocommandes ou tout autre générateur

d’impulsions, pour éviter tout actionnement involontaire de l’automatisme.

Ne pas permettre aux enfants, aux personennes ayant des capacités physi-

ques, mentales et sensorielles limitées ou dépourvues de l’expérience ou de

la formation nécessaires d’utiliser l’application en question.

L’utilisateur doit s’abstenir de toute tentative de réparation ou d’intervention

et doit s’adresser uniquement et exclusivement au personnel qualifié GENIUS

ou aux centres d’assistance GENIUS.

La hauteur minimum d’installation de l’automatisme est de 2,5m.

Ne jamais connecter plusieurs moteurs au même commande de mouve-

ment.

Ne pas connecter deux commandes de mouvements au même moteur.

Toujours actionner l’appareil à vue.

Tout ce qui n’est pas prévu expressément dans ces instructions est interdit.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

Page is loading ...

5

ENGLISH

Notes on reading the instruction

Read this installation manual to the full before you begin installing the product.

The symbol

indicates notes that are important for the safety of persons and for the good condition of the automated system.

The symbol draws your attention to the notes on the characteristics and operation of the product.

CE DECLARATION OF CONFORMITY FOR MACHINES

Manufacturer: GENIUS S.p.A.

Address: Via Padre Elzi, 32 - 24050 - Grassobbio- Bergamo - ITALIA

Declares that: Operator model. ROLL-UP 45 S

• is built to be integrated into a machine or to be assembled with other machinery to create a machine under the provisions of Directive 98/37/EC, and

subsequent amendments 91/368/EEC, 93/44/EEC, 93/68/EEC

• conforms to the essential safety requirements of the other following EEC directives:

73/23/EEC and subsequent amendment 93/68/EEC.

89/336/EEC and subsequent amendment 92/31/EEC and 93/68/EEC

furthermore, the manufacturer declares that the machinery must not be put into service until the machine into which it will be incorporated or of which it

will become a part has been identified and its conformity to the conditions of Directive 98/37/EC, 89/392/EEC and subsequent modifications assimilated

in Italian National legislation under Presidential Decree No. 459 of 24 July 1996 has been declared.

Grassobbio, 15-05-2007

The Managing Director

D. Gianantoni

INDEX

1 DESCRIPTION page.6

2 TECHNICAL SPECIFICATIONS page.6

3 GUIDE FOR CHOOSING THE MOTOR page.6

3.1 For roller shutters page.6

3.2 For sun blinds page.6

4 INSTALLATION page.7

4.1 ASSEMBLY OF TUBULAR MOTOR page.7

4.2 INSTALLATION OF TUBULAR MOTOR page.7

4.3 ELECTRICAL CONNECTIONS page.7

5 ADJUSTMENT OF THE TRAVEL-LIMIT STOPS page.7

5.1 ADJUSTMENT OF DESCENT TRAVEL-LIMIT STOP page.8

5.2 ADJUSTMENT OF RISE TRAVEL-LIMIT STOP page.8

6 EMERGENCY MANOEUVRE page.8

6

ENGLISH

TUBULAR MOTORS ROLL-UP 45 S

1 DESCRIPTION

2 TECHNICAL SPECIFICATIONS

ROLL-UP 45

MODEL

TORQUE

(Nm)

USE FRE-

QUENCY

MAX USE

TIME (min.)

SPEED

(Rpm)

VOLTAGE

(V)

FREQUENCY

(Hz)

POWER

(W)

CURRENT

(A)

MOTOR

SHAFT

MAX RO-

TATION

MOTOR

DIAMETER

(mm)

LENGTH

WITH ADAP-

TOR (mm)

PROTEC-

TION INDEX

28 S 15 20% 4 17 230 50 200 0.8 28 45 630 IP 44

56 S 30 20% 4 17 230 50 285 1.3 28 45 630 IP 44

65 S 35 20% 4 12 230 50 275 1.2 28 45 630 IP 44

90 S 45 20% 4 12 230 50 310 1.4 28 45 630 IP 44

3 GUIDE FOR CHOOSING THE MOTOR

Ref. Description

햲

Tubular motor.

햳

Example of wheel adaptor. (Accessory)

햴

Example of crown adaptor. (Accessory)

햵

Travel-limit stop ring-nut.

햶

Travel-limit stop adjustment tool.

햷

Travel-limit stop adjustment screws.

햸

Example of motor support. (Accessory)

햹

Eyelet for manual manoeuvre. (Accessory)

3.1 For roller shutters 3.2 For sun blinds

NUMBER OF

ARMS

ARM PROTRUSION

(m)

1.5 2 2.5 3 4

2 15 Nm 30 Nm 30 Nm 30 Nm 35 Nm

3 30 Nm 30 Nm 30 Nm 30 Nm 35 Nm

4 30 Nm 35 Nm 35 Nm 35 Nm 45 Nm

5 35 Nm 35 Nm 35 Nm 45 Nm

6 35 Nm 35 Nm 45 Nm

7 45 Nm 45 Nm

Fig. 1

7

ENGLISH

4 INSTALLATION

Before installing, select:

1) The Wheel and crown adaptor (Fig. 1 ref. 햳 - 햴) most suitable for

the type of roller to be moved.

2) The motor support most suitable for the application.

4.1 ASSEMBLY OF TUBULAR MOTOR

1) Fit the crown adaptor (Fig.2 ref.a) on the tubular motor, until it is completely

inserted on the guide (Fig. 2 ref. b) on the travel-limit ring-nut.

2) Insert the wheel adaptor on the motor shaft (Fig. 2 ref. 햴) and secure it

with the supplied Seeger ring (Fig. 2 ref. 햵).

4.2 INSTALLATION OF TUBULAR MOTOR

Table 1

ROLL-UP 45 MODEL MEASURE A (mm)

28 S 590

56 S 590

65 S 590

90 S 590

1) Drill a hole with a 3 mm diam. bit on the roller (Fig. 3 ref. 햳) at distance

A (Fig. 3 ref. 햲), referring to table 1.

2) Insert the assembled tubular motor inside the roller from the side opposite

the cap, until the crown adaptor is completely inside the roller (Fig. 4

ref. 햲).

3) Secure the wheel adaptor to the roller with a 4x10 self-tapping screw

inserted in the hole you had drilled, as shown in Fig. 4 ref. 햳.

4) Install the selected motor from the electric facilities side.

5) Secure the motorised roller on the motor support (Fig. 5 ref. 햲), and insert

it on the cap support (Fig. 5 ref. 햳), so that the travel-limit adjustment

screws are accessible and that the eyelet can be inserted on the tu-

bular motor.

6) Make sure that the motorised roller is perfectly horizontal and, if necessary,

modify the height of the cap or motor supports.

7) Insert the eyelet (Fig. 5 ref. 햴) in the appropriate hole on the tubular motor

and secure it with the supplied screw as shown in Fig. 5 ref. 햵.

4.3 ELECTRICAL CONNECTIONS

1) Before attempting any action on the system, cut out the electrical

power supply.

2) Install an omnipolar switch on the power supply line for the auto-

mated system, with contact opening distance of 3mm or more.

1) Connect the wires coming from the motor to an interlocked up-and-down

device without reset facility as in the lay-out of figure 6

2) Connect the up-and-down device to the power supply line as shown

in Fig. 6.

3) Power up the electro-roller

4) Press the rise push-button and check if the roller rotates in the winding

direction and stop the motor.

5) If the rotation direction is incorrect, cut power and - in the up-and-down

device (Fig. 6 ref. 햲 ) - change over the black wire with the brown wire

and check if operation is correct.

6) Press the descent push-button to check operation, and stop the motor.

5 ADJUSTMENT OF THE TRAVEL-LIMIT STOPS

A system of electro-mechanical travel-limit stops is housed inside the GENIUS

tubular motors. These stops cut power to the motor, when the opening or

closing limit of the roller-shutters is reached.

The travel-limit stop screws of ROLL-UP 45 S models, can be reached

from both sides of the motor (Fig. 7) - this facilitates installation and

adjustments.

Fig. 8

Fig. 7

Fig. 4

Fig. 3

Fig. 2

Fig. 6

Fig. 5

To help you find the travel-limit stop adjustment screws, refer to figures 9

- 10, according to the motor installation side (RH or LH), and to the box

configuration (internal or external).

8

ENGLISH

5.1 ADJUSTMENT OF DESCENT TRAVEL-LIMIT STOP

1) Hold down the descent push-button

2) Using the adjustment tool (Fig. 1 ref. 햶), turn the screw of the travel-limit stop corresponding to the roller’s descent rotation direction (Fig. 9 ref. 햲), toward

the plus sign (+) to increase the travel of the roller shutter, or toward the minus sign (-) to reduce it.

5.2 ADJUSTMENT OF RISE TRAVEL-LIMIT STOP

1) Hold down the rise push-button

2) Using the adjustment tool (Fig. 1 ref. 햶), turn the screw of the travel-limit stop corresponding to the roller’s rise rotation direction (Fig. 10 ref. 햲), toward

the plus sign (+) to increase the travel of the roller shutter, or toward the minus sign (-) to reduce it.

6 EMERGENCY MANOEUVRE

The ROLL-UP 45 S series tubular motors are equipped with a rescue manoe-

uvre device. Movement of the roller shutter is guaranteed by a manual

command even in the event of a temporary power cut.

If no power is supplied, insert the rod in the eyelet (Fig. 11 ref. 햲) and turn it

to open or close the roller shutter

• Before coupling the rod for the manual manoeuvre, cut power with

the differential switch.

• At the end of the manual manoeuvre, before powering up again,

remember to remove the control rod.

Fig. 11

Fig. 10

Fig. 9

Page is loading ...

10

FRANÇAIS

MOTORI TUBOLARI ROLL-UP 45 S

1 DESCRIPTION

2 CARACTÉRISTIQUES TECHNIQUES

MODÈLE

ROLL-UP

45

COUPLE

(Nm)

FRÉQUENCE

D’UTILISA-

TION

TEMPS

MAXI

UTILISATION

(min.)

VITESSE

(Rpm)

TENSION

(V)

FRÉQUENCE

(Hz)

PUISSAN-

CE (W)

COURANT

(A)

ROTA-

TIONMAXI

ARBRE

MOTEUR

DIAMÈTRE

MOTEUR

(mm)

LONGUEUR

AVEC

ADAPTATEUR

(mm)

INDICE DE

PROTEC-

TION

28 S 15 20% 4 17 230 50 200 0.8 28 45 630 IP 44

56 S 30 20% 4 17 230 50 285 1.3 28 45 630 IP 44

65 S 35 20% 4 12 230 50 275 1.2 28 45 630 IP 44

90 S 45 20% 4 12 230 50 310 1.4 28 45 630 IP 44

3 COMMENT CHOISIR LE MOTEUR

3.1 Pour rideaux à enroulement 3.2 Pour stores

NOMBRE

DE BRAS

DÉPASSEMENT DU BRAS (m)

1.5 2 2.5 3 4

2 15 Nm 30 Nm 30 Nm 30 Nm 35 Nm

3 30 Nm 30 Nm 30 Nm 30 Nm 35 Nm

4 30 Nm 35 Nm 35 Nm 35 Nm 45 Nm

5 35 Nm 35 Nm 35 Nm 45 Nm

6 35 Nm 35 Nm 45 Nm

7 45 Nm 45 Nm

Pos. Déscription

햲

Moteur tubulaire.

햳

Exemple d’adaptateur de la roue. (Accessoire)

햴

Exemple d’adaptateur de la couronne.

(Accessoire)

햵

Bague de fin de course.

햶

Outil de réglage des fins de course.

햷

Vis de réglage des fins de course.

햸

Exemple de support du moteur. (Accessoire)

햹

Œillet de manœuvre manuelle. (Accessoire)

Fig. 1

Page is loading ...

14

ESPAÑOL

MOTORES TUBULARES ROLL-UP 45 S

1 DESCRIPCIÓN

2 CARACTERÍSTICAS TÉCNICAS

MODELO

ROLL-UP

45

PAR (Nm)

FRECUEN-

CIA

DE UTILIZA-

CIÓN

TIEMPO

MÁX.UTI-

LIZACIÓN

(min.)

VELO-

CIDAD

(Rpm)

TENSIÓN

(V)

FRECUEN-

CIA (Hz)

POTEN-

CIA (W)

CORRIENTE

(A)

ROTA-

CIÓNMÁX.

EJE MO-

TOR

DIÁMETRO

MOTOR

(mm)

LONGITUD

CON ADAP-

TADOR

(mm)

ÍNDICE DE

PROTEC-

CIÓN

28 S 15 20% 4 17 230 50 200 0.8 28 45 630 IP 44

56 S 30 20% 4 17 230 50 285 1.3 28 45 630 IP 44

65 S 35 20% 4 12 230 50 275 1.2 28 45 630 IP 44

90 S 45 20% 4 12 230 50 310 1.4 28 45 630 IP 44

3 GUÍA PARA LA ELECCIÓN DEL MOTOR

3.1 Para persianas enrollables 3.2 Para toldos de sol

NÚMERO

DE

BRAZOS

SALIENTE BRAZOS

(m)

1.5 2 2.5 3 4

2 15 Nm 30 Nm 30 Nm 30 Nm 35 Nm

3 30 Nm 30 Nm 30 Nm 30 Nm 35 Nm

4 30 Nm 35 Nm 35 Nm 35 Nm 45 Nm

5 35 Nm 35 Nm 35 Nm 45 Nm

6 35 Nm 35 Nm 45 Nm

7 45 Nm 45 Nm

Pos. Descripción

햲

Motor tubular.

햳

Ejemplo de adaptador rueda. (Accesorio)

햴

Ejemplo de adaptador corona. (Accesorio)

햵

Tuerca final de carrera.

햶

Útil de regulación del final de carrera.

햷

Tornillos de regulación del final de carrera.

햸

Ejemplo de soporte motor. (Accesorio)

햹

Argolla para maniobra manual. (Accesorio)

Fig. 1

Page is loading ...

Le descrizioni e le illustrazioni del presente manuale non sono impegnative. GENIUS si riserva il diritto, lasciando inalterate le caratteristiche essenziali dell’appa-

recchiatura, di apportare in qualunque momento e senza impegnarsi ad aggiornare la presente pubblicazione, le modifiche che essa ritiene convenienti per

miglioramenti tecnici o per qualsiasi altra esigenza di carattere costruttivo o commerciale.

The descriptions and illustrations contained in the present manual are not binding. GENIUS reserves the right, whils leaving the main features of the equipments unal-

tered, to undertake any modifications to holds necessary for either technical or commercial reasons, at any time and without revising the present publication.

Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. GENIUS se réserve le droit d’apporter à tout moment les modifications qu’elle

jugera utiles sur ce produit tout en conservant les caractéristiques essentielles, sans devoir pour autant mettre à jour cette publication .

Las descripciones y las ilustraciones de este manual no comportan compromiso alguno. GENIUS se reserva el derecho, dejando inmutadas las características

esenciales de los aparatos, de aportar, en cualquier momento y sin comprometerse a poner al día la presente publicación, todas las modificaciones que considere

oportunas para el perfeccionamiento técnico o para cualquier otro tipo de exigencia de carácter constructivo o comercial.

Die Beschreibungen und Abbildungen in vorliegendem Handbuch sind unverbindlich. GENIUS behält sich das Recht vor, ohne die wesentlichen Eigenschaften

dieses Gerätes zu verändern und ohne Verbindlichkeiten in Bezung auf die Neufassung der vorliegenden Anleitungen, technisch bzw, konstruktiv / kommerziell

bedingte Verbesserungen vorzunehmen.

De beschrijvingen in deze handleiding zijn niet bindend. GENIUS behoudt zich het recht voor op elk willekeurig moment de veranderingen aan te brengen die het

bedrijf nuttig acht met het oog op technische verbeteringen of alle mogelijke andere productie- of commerciële eisen, waarbij de fundamentele eigenschappen

Timbro rivenditore: / Distributor’s stamp: / Timbre de l’agent: / Sello del revendedor: / Fachhändlerstempel: / Stempel dealer:

Via Padre Elzi, 32

24050 - Grassobbio

BERGAMO-ITALY

tel. 0039.035.4242511

fax. 0039.035.4242600

[email protected]

www.geniusg.com

00058I0670 Rev.1