Congratulations on your purchase of a Sevylor inflatable product. We take pride in bringing you a quality product which will

offer you years of pleasure. Your new item is an investment which deserves your care and attention. These instructions

have been compiled to help you to operate your product safely. It contains details of the product, its equipment, and

information on its operation and maintenance. Read it carefully and familiarise yourself with the inflatable before first use,

in order to ensure safe use and prevent tragic accidents.

The warnings below relate to various situations. Please observe them.

N.B. The inflated sizes are measured under the following conditions ; product inflated with the recommended inflator, at

the recommended working pressure and at a temperature ranging between 18°C / 64°F and 22° C / 71°F.

Before inflating the kayak please put the front deck lift and the fin in place.

You will find, supplied with your kayak a black flexible plastic strip. Insert this strip into the pockets located on the inner

walls of the side tube chambers, right under the front deck. For easier installation it is recommended to put the deck lift

strip in place before inflation. Pay attention to the small arrow sticker on the strip, which should be pointing forward,

towards the bow (front tip) of the kayak. This is important as the deck lift strip is not symmetrical and the ends are cut in an

Attach the fin on the underside by folding the hull. Insert the extremities of the fin in the loops and stretch the hull as much

as possible to hold it in position. Once the kayak is inflated, this operation becomes impossible. The curvature of the fin

When inflating for the first time, inflate indoors at room temperature – the PVC will be soft and assembly will be easier. If

the item was stored below 0°C / 32°F, leave it at 20°C / 68°F for 12 hours before unfolding. Inflate it with an inflator from

Sevylor or any inflator designed for inflatable boats, rafts, pool floats, air beds, camping mattresses, and other low

pressure inflatables. These types of inflators have a hose and adaptors to fit the valves on this product.

Choose a smooth and clean surface on which to unfold your product.

1. Your kayak is equipped with two different types of valves:

which fits the valve. Close the valve and press it into the air chamber.

2. Inflate the kayak in the order of inflation as shown on the capacity plate printed on the product (European model) ; see

models. Note: the bladders inside the hull are tied to the hull with little tie down ropes, which can be accessed through

the zippers in the center and in the tips of the side chambers, under the deck. Should the bladders have shifted during

transportation causing distortion of the shape of the kayak, readjust the bladder position as necessary. Adjustments to

bladder positioning should be done only while the bladders are deflated, or only slightly inflated. Do not open the hull

zippers or attempt to adjust the bladders when they are fully inflated.

3. Max. air pressure : the correct pressure for the side chambers is 0.1 bar (= 100 mBar) ; the correct pressure for

the floor chamber is : 0.06 bar (= 60 mBar). Do not exceed it. *A manometer is supplied with your kayak and will

allow you to check the pressure in the air chambers. Overpressure : deflate until you reach the recommended

pressure. Drop of pressure : inflate again slightly.

FIRST, inflate the side (main) chambers softly at first to stretch out the boat and allow the side chambers to take proper

shape. Then top them off alternately until they are free of wrinkles and feel firm to the touch. Observe the tips of the boat

and make sure the side tubes are inflated evenly and the tips are straight. Do not over-inflate!

several) drain port(s) with a plug. When using your kayak, the drain plug(s) should be closed, so no water enters the boat

and you can enjoy a dry kayak. Before entering the water, please check the drain plug(s) and make sure it is (they are)

securely closed by pressing the plug(s) along the edge with your thumb. As with any water activity and depending on

conditions and use, some water may enter the kayak. Therefore after use and taking your kayak out of the water, open the

drain plug(s), allowing any water that may have entered to drain. You can also stand the craft up on it’s rear tip, forcing all

water to run down to the drain port(s), however handle with care and be cautious not to damage the tip of the kayak by

abrading it on the ground.

rear edge of the cockpit, feed it through the D-ring on the backrest and back through the buckle and tighten it. This will lift

the rear deck, giving the kayak the proper shape and run-off surface for any water splashes during use.

Included feature are also the bungee paddle holders, located on both sides (K1 on one side only) of the cockpit, right

under the soft tube-edge of the cockpit. When you need to attach your paddle or a spare paddle to the kayak, unhook the

bungee cord, wrap it around the paddle shaft and attach the hook again to the bungee cord itself. Unhook them

accordingly to release your paddle.

The POINTER kayaks have an all around spray deck for better comfort and protected storage space.

attached to the cockpit and stays in place during use and the paddling motion of the user. To detach the apron and exit the

kayak at any time, just pull on the front handle of the apron and lift it.

1. Remove paddles and other accessories.

5. When storing your inflatable, keep it in a clean and dry place, away from extreme temperature variations or other

potentially damaging factors. It can be stored deflated and rolled up in a bag or assembled and lightly inflated. Store it

away from rodents.

Remove the inside tube from the hull. Check that the tube is fully deflated and lies flat.

1. Draw the shape of the patch exactly where it will be applied, cut a round patch at least 2” / 5 cm larger than the

cut/damaged area.

2. Clean the damaged area and the corresponding side of the patch with a grease remover of the alcohol type and allow

for it to dry for 5 minutes.

3. Apply 3 thin layers of glue on both the patch and the damaged area, allow for it to dry for 5 minutes between layers

until the glue feels tacky.

4. When the third layer of glue is dry, apply the patch without pressing and adjust the positioning if required, press the air

bubbles which may have formed under the patch by smoothing the patch with a round object such as a spoon, do this

procedure by starting in the center of the patch towards the outside, clean the excess glue with a solvent. Drying : 12

 Avoid inhaling glue vapors or swallowing.



away from children’s reach.

N.B. the repairs on the weldings must not be glued. Only the manufacturer of the boat can perform the repairs on the

weldings.

Sevylor warrants (legal warranty) to the original purchaser only, and from date of purchase, when any product is used for