Kenwood C-V301 User manual

Kenwood
Brand
Kenwood
Model
C-V301
Category
AV receivers
Type
User manual

This manual is also suitable for

AV CONTROL CENTER
B60-4349-00
C-V351
C-V301
INSTRUCTION MANUAL
KENWOOD CORPORATION
This manual contains instructions for two models. Model availability and features
(functions) may differ depending on country and sales area.
EN
2
C-V351/C-V301 (EN)
Batteries(R6/AA) (4)
(C-V351)
FM indoor antenna (1) AM loop antenna (1)
Graphical Remote Control unit (1)
(C-V351)
Accessories
ON/STANDBY
MUTE
VOLUME
ENTER
Setup
DVD/6ch Input
Sound Speaker
C D
Sat.
Tape1
Cable
Reset
VCR1
VCR2
L D
T V
Confirm
Set Up
Return
Input
Source
Main Menu
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1TVSat.Cable
Units are designed for operation as follows.
Europe and U.K. .............................................. AC 230 V only
WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI-
ANCE TO RAIN OR MOISTURE.
Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage.
If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without
delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. We recommend that you
retain the original carton and packing materials for use should you transport or ship the unit in the future.
Unpacking
Before applying power
Safety precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS IN-
TENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN
THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF
ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO
THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALI-
FIED SERVICE PERSONNEL.
Factory fitted moulded mains plug
1. The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse.
2. The fuse cover must be refitted when replacing the fuse in the moulded plug.
3. Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to
reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer.
If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent
connection to the mains supply.
IMPORTANT: The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
Do not connect those leads to the earth terminal of a three-pin plug.
For the United Kingdom
Remote control unit (1)
(C-V301)
Loop antenna stand (1)
Batteries(R6/AA) (2)
(C-V301)
Caution : Read this page carefully to ensure safe operation.
(Optional with the C-V301)
3
C-V351/C-V301 (EN)
Contents
Caution : Read the pages marked
carefully to ensure safe operation.
Before applying power.............................................................................................................................................................................................. 2
Safety precautions ......................................................................................................................................... 2
Unpacking ........................................................................................................................................................... 2
Contents ........................................................................................................................................................................................................................ 3
Special features.......................................................................................................................................................................................................... 4
System connection ..................................................................................................................................................................................................... 5
Connection of audio components (CD player, MD recorder, cassette deck, power amplifier) ........................ 5
Connection of video components (LD player, VCR, DVD) .................................................................................. 6
About the system control connections .............................................................................................................. 7
Connection of flat-cable connector ................................................................................................................... 7
Connection of antenna ....................................................................................................................................... 8
Controls and indicators ............................................................................................................................................................................................ 9
Setup of the Graphical Remote Control (GRC) unit (For C-V351).................................................................................................................... 11
Controls and indicators(Optional with the C-V301)......................................................................................... 11
Setting up the GRC according to your AV CONTROL CENTER (Model Type Setup) ....................................... 12
Setting up the GRC according to the option components (Set Up) ...................................................................... 13
Setting up the GRC according to other components (Set Up)......................................................................... 15
Remote control of components from the GRC (For C-V351)............................................................................................................................. 16
Controlling the AV CONTROL CENTER............................................................................................................. 16
Controlling the components connected through system control cords .......................................................... 17
Remote control with the “RC”unit (For C-V301) ................................................................................................................................................. 20
Names and functions of the keys .................................................................................................................... 20
Convenient functions ............................................................................................................................................................................................... 21
One-touch operation and easy operation features ......................................................................................... 21
Playing music ........................................................................................................................................................................................................... 22
Sound adjustment functions.................................................................................................................................................................................. 23
Recording .................................................................................................................................................................................................................. 25
Broadcast reception ............................................................................................................................................................................................... 26
Receiving broadcast station............................................................................................................................. 26
RDS (Radio Data System) ....................................................................................................................................................................................... 27
Functions of RDS .............................................................................................................................................. 27
DISPLAY key ..................................................................................................................................................... 27
Storing RDS stations automatically in preset memory (AUTO MEMORY) ..................................................... 28
Receiving a preset RDS station ....................................................................................................................... 28
Storing radio stations manually in preset memory ......................................................................................... 29
Receiving a preset station ............................................................................................................................... 29
Receiving all preset stations in order (P. CALL) ............................................................................................... 29
Searching for a desired program type (PTY search) ........................................................................................ 30
Reserving reception of desired kind of programme in advance (EON reservation) ....................................... 32
To cancel EON reservation ............................................................................................................................... 33
Ambience effects...................................................................................................................................................................................................... 34
Sound modes .................................................................................................................................................... 34
Setup for surround play.................................................................................................................................... 36
Surround play ................................................................................................................................................... 38
Setup for surround play (while listening to music) ......................................................................................... 39
Setup of the surround effect parameters (DSP) .............................................................................................. 43
Clock adjustment ...................................................................................................................................................................................................... 45
Displaying the Time.......................................................................................................................................... 45
Timer operation ......................................................................................................................................................................................................... 46
Timer programming .......................................................................................................................................... 46
Activating the timer ......................................................................................................................................... 48
Sleep timer ....................................................................................................................................................... 49
Set up code chart...................................................................................................................................................................................................... 50
VCR Set up codes ............................................................................................................................................. 50
TV Set up codes................................................................................................................................................ 51
TV Set up codes................................................................................................................................................ 52
LD Set up codes................................................................................................................................................ 52
Satellite Set up codes ...................................................................................................................................... 53
Cable Set up codes........................................................................................................................................... 53
In case of difficulty .................................................................................................................................................................................................. 54
Specifications ..................................................................................................................................................................................................... 56
Before applying power
4
C-V351/C-V301 (EN)
The GRC unit incorporates a large-screen LCD which displays key icons and parameters. The LCD also shows information on the operating
modes of the main unit.
To improve the operability, frequently used icons are located in the higher hierarchy in the LCD display and icons which are associated
between each other are shown on the same screen.
The GRC unit is a multi-function remote control unit which can be programmed to control AV components from other manufacturers than
KENWOOD.
In the case of C-V301, It is able to use Graphical Remote Control (GRC-151/Option).
True home theater sound
Dolby Pro Logic & Dolby 3 Stereo
This surround system reproduces theater-like surround sound from video software marked .
The PRO LOGIC mode uses the built-in adaptive matrix circuit to steer the Left, Center, Right and Surround channel audio signals.
The 3 STEREO mode will redirect the surround signal to the front left and right speakers when only the front and center speakers are used.
New DSP surround modes
The DSP (Digital Signal Processor) used for this AV CONTROL CENTER incorporates a variety of high quality adjustable sound fields, like
"ARENA", "JAZZ CLUB"and "STADIUM", to add the “presence” associated with an arena, jazz club or stadium (etc.) to the original signal.
It is compatible with almost any kind of program source.
Special features
This AV CONTROL CENTER is equipped with a RDS tuner that provides several convenient tuning functions: AUTO MEMORY, to
automatically preset up to 40 RDS stations broadcasting different programs; station name display, to show you the name of the current
broadcast station; and PTY search to let you tune stations by program type.
Graphical Remote Control unit ”GRC”(Optional with the C-V301)
Simply pressing the play key of the CD player or cassettedeck turns the system on and starts playback.
How to use this manual
In this manual, the operating procedures are described on the left half of each page and the supplementary explanation,
display information and other notes on each step are described on the right half.
Operating procedure steps (Left half)
(Example of instructions in this manual)
Step No.
Remote control
unit to be used
Graphical remote
control key to be used
Icon selection Press ENTER key.
Supplementary explanation
for the remote control unit
or Main unit operation(s)
Supplementary
explanation for the
graphical remote
control operation
Supplementary explanation (Right half)
2 Entry
Each press switches the
indication.
1 ARENA
2 JAZZ CLUB
3 STADIUM
1
ENTER
ENTER
DSP Mode
ENTER
Select the DSP surround mode.
Select DSP.
1 Selection cursor
RC
GRC
GRC
RDS (Radio Data System) tuner
ONE TOUCH OPERATION
Arena
Sound DSP Mode
DSP
Special features
RC/Main unit
5
C-V351/C-V301 (EN)
ANTENNA
AM
FM 75Ω
GND
CONNECT WITH
POWER AMPLIFIER
SYSTEM
CONTROL
CD
AUX TAPE 1/ MD
IN
IN REC
PLAY
TAPE 2
(MONITOR)
REC
PLAY
MONITOR
OUT
VIDEO
UNSWITCHED
L
R
DVD
IN
AUDIO
FRONT
REC
PLAY
SURROUND
CENTER
SUBWOOFER
LD
/DVD
VCR
DVD 6CH.INPUTDVD 6CH.INPUT
Also connect the system control cords when the
KENWOOD Audio Component System “SERIES 21” is
connected.
The connected components shown here are given as examples
because the available models vary depending on marketing areas.
System connection
Connection of audio components
(CD player, MD recorder, cassette deck, power amplifier)
Make connection as shown below.
When connecting the related system components, refer
also to the instruction manuals of the related compo-
nents.
Do not plug in the power lead until all connections are
completed.
Malfunction of microcomputer
If operation is not possible or erroneous display appears even
though all connections have been made properly, reset the
microcomputer referring to “In case of difficulty”.
R
System
control cord
System control cord
CAUTION (For U.K.)
When using the AC out-
lets equipped with this
unit, be sure to consult
your dealer for the cor-
responding plug.
To wall
AC outlet
*
2
Graphic equalizer
or Cassette deck 2
MD recorder or
Cassette deck 1
*
1
Power amplifier
CD player
Shape of AC outlet
Europe
*
1
For the connection and operation proce-
dures of the power amplifier and speak-
ers, refer to the instruction manual of
the power amplifier (M-A300 or M-A100).
Analog disc turntable
(with built-in equalizer amp)
Connection
cable
CAUTION
Be sure to adhere followings. Or proper ventilation will be blocked
causing damage or fire hazard.
÷ Install the R-SE7 on the top of the system.
÷ Do not place any objects impairing heat radiation onto the
top of unit.
÷ Leave a space around the unit (from the largest outside di-
mension including projection) equal or greater than, shown
below.
Top panel : 50 cm
Side panel : 10 cm
Back panel : 10 cm
*
2
Do not connect system control cord to the cassette
deck connected to the TAPE 2 (MONITOR) jacks.
REC IN
PLAY
OUT
PLAY
OUT
REC
IN
LINE
OUTPUT
6
C-V351/C-V301 (EN)
Connection of video components
(LD player, VCR, DVD)
Audio OUT
Audio IN
Video IN
Video OUT
DVD
VCR
Audio
OUT
Video
IN
Video
OUT
To wall AC outlet
The connected components are given as examples because the avail-
able models vary depending on marketing areas.
Monitor TV
LD player
System connection
ANTENA
AM
FM 75Ω
GND
SYSTEM
CONTROL
CD
AUX TAPE 1/ MD
IN
IN REC
PLAY
TAPE 2
(MONITOR)
AUDIO
REC
PLAY
MONITOR
OUT
VIDEO
UNSWITCHED
L
R
CONNECT WITH
POWER AMPLIFIER
IN REC
PLAY
VCR
FRONT
SURROUND
CENTER
SUBWOOFER
DVD 6CH.INPUTDVD 6CH.INPUT
LD
/DVD
Video OUT
Audio CENTER OUT/
SUBWOOFER OUT
Audio FRONT OUT
Audio SURROUND OUT
7
C-V351/C-V301 (EN)
When this unit is connected to KENWOOD audio component system “SERIES 21”, also connect them through the system control cords
to allow system-control operations between components.
Connection example
The SERIES 21 components which can be
system-connected with this unit include
the LD player, MD recorder, and DVD player.
Inserting the connector
Push and hold the two ends of the
connector, and pull it straight
outward.
Connection of flat-cable connector
Push in the
connector straight
into the socket until it
clicks to indicate the
locking.
Removing the connector
About the system control connections
1. Do not connect the SERIES 21 components
to other system components using system
control cords.
2. Do not connect system control cords to any
components other than those specified by
KENWOOD. It may cause a malfunction and
damage your equipment.
3. Be sure the system control plugs are in-
serted all the way in to the system control
terminals.
About the system control operations
(Available operations when SERIES 21 components are connected through system control cords)
Remote Control
Lets you operate source components with the system remote supplied with this unit.
Automatic Operation
When you start playback from a source component, the input selector on this unit switches to that component automatically. (Except TAPE 2)
Synchronized Recording
Lets you synchronize recording with the start of playback when recording from CD or LD.
1. Connect all cords firmly. If connections are loose, there could be loss of sound or noise produced.
2. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging / unplugging
connection cords without removal of the power cord can cause malfunctions or damage to the unit.
3. Do not connect up a power source which is larger than that indicated on the socket at the rear of the unit.
4. If the system control cords or audio cords are not connected properly, the remote control or automatic operation between system
components will not work properly.
NotesNotes
Notes
NotesNotes
Notes
System connection
SYSTEM
CONTROL
SYSTEM
CONTROL
SYSTEM
CONTROL
SYSTEM
CONTROL
AV
CONTROL
CENTER
POWER
AMPLIFIER
CD
PLAYER
CASSETTE
DECK
System
control cord
System
control cord
System
control cord
GRAPHIC
EQUALIZER
8
C-V351/C-V301 (EN)
ANTENA
AM
FM 75Ω
GND
ANTENNA
AM
FM 75Ω
GND
ANTENA
AM
FM 75Ω
GND
ANTENNA
AM
FM 75Ω
GND
ANTENA
AM
FM 75Ω
GND
Connection of antenna
Connection method to each antenna terminal
1 Push lever. 2 Insert cord. 3 Return lever.
AM loop antenna connection
The supplied antenna is for indoor use. Place it as far as possible from the
main system, TV set, speaker cords, and power cord, and set it to a
direction which provides the best reception.
FM outdoor antenna connection
Lead the 75 Ω coaxial cable connected to the FM outdoor antenna into
the room and connect it to the FM 75 Ω terminal.
FM indoor antenna connection
The accessory antenna is for temporary indoor use only. For stable signal
reception we recommend using an outdoor antenna. Remove the indoor
antenna if you connect one outdoors.
Use the commercially
available antenna adaptor.
System connection
9
C-V351/C-V301 (EN)
ON/STANDBY
PHONES
INPUT TAPE 2
(MONITOR)
VOLUME CONTROL
DOWN
UP
AV CONTROL CERTER KC-2
CLOCK
TIMER
MODE
RDS
PTY
DISPLAY
TIMER
SET
S.DIRECT
TA/NEWS/INFO.
STEREO
DSP
A.MEMO
AUTO BAND
TUNING
PTY SELECT
MODE
MULTI.CONTROL
LEVEL
OPEN/CLOSE
1
3
(¡ ™)£¢
AUTO
RDS
EON
PTY
TIMER
NEWS
INFO.
FM
LW
MW
TATP
PRO LOGICPRO LOGIC
3 STEREO
DSPDSP
TAPE 2
STEREO
TUNED
MUTE
SLEEP
dB
ms
MHz
kHz
1
2
SOURCE
DIRECT
MEMO
4
0
9
8
765
!
@
#
$^%
&
*
2
The keys which have the same names as the controls on the
remote control unit provide the same functions as them.
$ TIMER MODE key
Press to switch the timer modes.
% S.DIRECT key
Press to switch the Source Direct function
which allows to reproduce the source with
a better quality.
^ RDS DISPLAY key
Press to switch the RDS display.
& RDS PTY key
For use during reception of RDS broadcast-
ing.
* RDS TA/NEWS/INFO. key
For use during reception of RDS broadcasting.
( A.MEMO key
Press when using the auto memory func-
tion.
) AUTO key
Press to select the tuning mode.
The auto tuning or manual tuning mode can
be selected.
The input selection display of a source can
be switched to another by pressing and
holding the AUTO key for more than 2
seconds.
0
1
(ON/STANDBY) key
Press to switch between ON and STANDBY.
2 Remote sensor
3 TIMER SET key
Press to set the timer function.
4 CLOCK key
Press to set the clock.
5 STEREO key
6 DSP key
7 DOLBY key
8 MODE key
Press to switch various setting modes.
9 MULTI.CONTROL key
Press to select various setting modes.
0 GRC transmitter
Outputs the signals transmitted to the
Graphical Remote Control.
! PHONES jack
For use in headphones listening.
@ INPUT SELECTOR key
Press to select the input.
# TAPE 2 (MONITOR) key
For use in monitoring of recording, etc.
¡ BAND key
Press to switch the broadcasting band.
™ TUNING key ( , )
Press to select the radio station to be re-
ceived.
These keys are also used in the clock adjust-
ment and timer operations.
£ OPEN/CLOSE key
¢ VOLUME CONTROL knob
MEMORY indicator
RDS indicators
(RDS, TP, TA, EON, PTY, NEWS, INFO.)
Frequency display, input
selector display, preset
channel display, surround
mode display
Decibel indicator
Delay time indicator
DSP indicator
TAPE 2
indicator
AUTO tuning mode/AUTO stereo
reception indicator
STEREO indicator
TUNED indicator
MUTE indicator
SOURCE DIRECT indicator
SLEEP
TIMER
indicator
PRO LOGIC
indicator
3 STEREO
indicator
Receiving frequency
unit indicators
Display
TIMER
indicators
Broadcast band
indicators
Standby mode
While the standby indicator of the unit is lit, a small amount of current is flowing into the unit’s internal circuitry to back up the memory. This condition
is referred to as the standby mode of the unit. While the unit is in the standby mode, it can be turned ON from the remote control unit.
With this unit, standby mode is indicated by means of the display panel. The system is in standby mode while the clock display is shown.
Controls and indicators
10
C-V351/C-V301 (EN)
OPEN/CLOSE
Note
Note
Opening/closing the door
When opening or closing the door, be careful not to catch
your finger in the door. Otherwise there is a risk of injury.
Changing the input selection display (AUTO key)
1 Select “TAPE 1” with the INPUT SELECTOR .
2 Press and hold the AUTO key for more than 2 seconds, until
“MD” is displayed.
*1: To change the TAPE 1 display to MD display
*2: To change the LD display to the DVD display
Each press switches the indication.
Each press switches the indication.
To make the system control operation, the input selection display
should be switched according to the actually connected compo-
nents.
About the system control connections
7
Switching the display mode (DISPLAY key)
Use the following procedure to change the display mode.
Press the DISPLAY key (RC and GRC only).
Select "Display" from "Main Menu 2" when using the GRC.
Each press switches the indication.
÷ The time display is displayed for only 5 seconds, after which the INPUT
SELECTOR display appears automatically.
÷ The display of 2 is not shown during SOURCE DIRECT and 6ch INPUT
operations.
÷ With the C-V301, the display does not change while the INPUT
SELECTOR is set for the LD input.
1 TAPE1 2 MD
1 LD 2 DVD
1 INPUT SELECTOR
display
2 DOLBY/DSP/
STEREO
display
3 Time
display
1 Select “LD” with the INPUT SELECTOR .
2 Press and hold the AUTO key for more than 2 seconds, until
“DVD” is displayed.
Controls and indicators
11
C-V351/C-V301 (EN)
Setup of the Graphical Remote Control (GRC) unit (For C-V351)
Controls and indicators
(Optional with the C-V301)
Approximate operating range
Remote sensor
Infrared remote control
GRC or RC
Infrared ray system
1. The supplied batteries are intended for use in operation check.
Therefore, their lives may be shorter than ordinary batteries.
2. When the remote-controllable distance gets shorter than
before, replace all four batteries with new ones.
3. Malfunction may occur if direct sunlight or the light of a high-
frequency lighting fluorescent lamp enters the remote sen-
sor. In such a case, change the system installation position to
prevent the malfunction.
4. The GRC display may show erroneous information when the
GRC unit is operated from outside the specified range.
Notes
Notes
For C-V351
Note
Note
The Graphical Remote Control (GRC) unit provided with the AV CONTROL CENTER can also control KENWOOD cassette decks,
CD player, DVD player and LD player which are connected to it through system control cords. For details of the controllable
functions, refer to the instruction manuals of these components.
Model:GRC-151
Infrared system
Perform “Model Type Setup”
of the GRC before using it.
The following menu screen
appears immediately after
the batteries have been
loaded for the first time.
Segment screen
Menu screen
Operation keys
1 Segment screen
This area displays the fixed icons.
2 Return icon
Select to return to the previous
display.
3 Main Menu icon
Select to change the input source
or select Main Menu 2.
4 Confirm icon
Select to confirm a setting, etc.
5 Sound icon
Select to control the sound-related
functions.
6 DVD icon
Select to control the DVD player.
7 CD icon
Select to control the CD player.
8 MD icon
Select to control the MD recorder.
9 Tuner icon
Select to control the tuner.
0 LD icon
Select to control the LD player.
! Tape A icon
Select to control cassette deck A.
@ Tape 1 icon
Select to control cassette deck 1.
# Tape B icon
Select to control cassette deck B.
$ Cable TV icon
Select to control the cable TV.
% TV icon
Select to control the TV.
^ VCR 1 icon
Select to control VCR 1.
& Satellite Tuner icon
Select to control the satellite tuner.
* VCR 2 icon
Select to control VCR 2.
( Set Up icon
Select to make setup operations.
) Menu screen
This area displays the
control key icons and
level information.
¡ Mode display
The above illustration
indicates the Setup
mode.
™ CD icon
Select to set up the
CD player.
£ Reset icon
Select to return to the
“Model Type Setup”
menu screen.
¢ Joystick key
For use in selecting icons.
The joystick moves in 8 direc-
tions.
∞ ENTER key
Press to enter a selection.
§ VOLUME (UP) control key
Press to increase the volume
level.
VOLUME (DOWN) control
key
Press to decrease the volume
level.
• MUTE key
Press to mute sound temporarily.
ª (ON/STANDBY) key
Press to switch the AV CONTROL
CENTER and the components
connected to it through system
control cords between ON and
STANDBY.
÷ The input source can be selected
using icon 3.
÷ Icons 6 to * are used to select the
component to be controlled.
The displayed icons are variable depending on the “Model
Type Setup” for matching the specifications with the AV
CONTROL CENTER which uses the GRC unit and “Setup” for
matching the specifications with connected source compo-
nent.
Model
T
yp
e Setu
p
Model
6
Model
5
Model
4
Model
3
Model
2
Model
1
ON/STANDBY
MUTE
VOLUME
ENTER
Setup
DVD
Sound
C D
Sat.
Tape1
Cable
Reset
VCR1
VCR2
L D
M D
T V
Confirm
Set Up
Return
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1
TV
Sat.Cable
MD
Main
Menu
DVD
§
•
£
ª
)
™
1
2
34567890!@#$%^&*(
¢
∞
¡
30°
5m
30°
12
C-V351/C-V301 (EN)
3
1
2
ON/STANDBY
MUTE
VOLUME
ENTER
Model
T
yp
e Setu
p
Model
6
Model
5
Model
4
Model
3
Model
2
Model
1
Model
T
yp
e Setu
p
Model
6
Model
5
Model
4
Model
3
Model
2
Model
1
1
3
2
4
Set Up
ENTER
Reset
ENTER
ENTER
ENTER
Setup of the Graphical Remote Control (GRC) unit
Setting up the GRC according to your AV CONTROL CENTER
(Model Type Setup)
Perform the following procedure after inserting batteries for
the first time and every time after changing them.
Preparation
÷ Press the (ON/STANDBY) key
of the main unit to the ON mode.
Model Type Setup (GRC setup procedure)
Loading batteries
1 Remove the cover. 2 Insert batteries. 3 Close the cover.
The “Model Type Setup” screen ap-
pears.
Check the display.
Select "Model 2."
Move the cursor.
It can be moved in 8 directions depend-
ing on how you press the joystick key.
Enter the selection.
Press the ENTER key.
1 Select Set Up.
2 Press the ENTER key.
4 Press the ENTER key.
3 Select Reset.
5 Perform the setup procedure from step ”2 Check the display”.
To reset GRC setting
GRC
“Model Type Setup” icon
Main operation menu
C-V301 ............................................... Model 2
C-V351 ............................................... Model 2
AV CONTROL CENTER
Model
For C-V351
The icon on which the cursor is moved blinks in reverse
video.
Caution in battery replacement
÷ Insert four AA-size (R6/AA) batteries
as indicated by the polarity marking.
÷ To maintain the memory of the settings you
made before, complete the battery replace-
ment operation within 30 seconds.
÷ The procedure on the left should also be per-
formed when resetting the GRC (as a measure
against its malfunction). However, in this case,
wait for about five minutes after removing the
batteries and before re-inserting them.
÷ The above operation clears all of the previously made settings and
resets the unit to the initial condition.
13
C-V351/C-V301 (EN)
Set Up
Set Up
Set Up
C D
Sin
g
le
Dual
L D
System Control
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
Tape1
Setting up the GRC according to the option components
(Set Up)
The following procedures prepare the GRC for operating the
components connected through system control cords. Make
sure that these components are connected through system
control cords. 7
÷ If you proceed to the following “Set Up” operations immediately after steps 1 to 4 of “Model Type
Setup (GRC setup procedure)” on page @, start operation with step “3 Select the CD icon” in
the “Set Up CD” procedure.
Set Up CD Set Up Tape 1 Set Up LD
Main operation menu
÷ Select “Single”, “Dual”, “Carrousel” or
“Changer” according to the connected
CD player type.
1 Select the ”Set Up“ icon.
2 Press the ”ENTER“ key to enter the
selection.
3 Select the ”CD“ icon.
4 Press the ”ENTER“ key to enter the
selection.
5 Select the ”Single“ icon.
6 Press the ”ENTER“ key to enter the
selection.
7 Select the ”Main Menu“ icon.
8 Press the ”ENTER“ key to enter the
selection.
÷ Select “Dual” or “Single” according to
the connected cassette deck type.
1 Select the ”Set Up“ icon.
2 Press the ”ENTER“ key to enter the
selection.
3 Select the ”Tape 1“ icon.
4 Press the ”ENTER“ key to enter the
selection.
5 Select the ”Dual“ icon.
6 Press the ”ENTER“ key to enter the
selection.
7 Select the ”Main Menu“ icon.
8 Press the ”ENTER“ key to enter the
selection.
÷ Select “System Control” or “IR” ac-
cording to the connected LD player type.
1 Select the ”Set Up“ icon.
2 Press the ”ENTER“ key to enter the
selection.
3 Select the ”LD“ icon.
4 Press the ”ENTER“ key to enter the
selection.
5 Select the ”System Control“ icon.
6 Press the ”ENTER“ key to enter the
selection.
÷ Icon
appears at the moment the setup
has completed.
÷ Icons
/ or icon appear at the
moment the setup has completed.
÷ Icon
appears at the moment the setup
has completed.
In the operations of the GRC (Graphical Remote
Control unit), proceed to each step within 10
seconds after the previous step.
The display disappears in 10 seconds.
To resume GRC display, move the Joy-
stick key in any directions.
Setup of GRC according to the
CD player in use
Setup of GRC according to the
cassette deck in use
Setup of GRC according to the
LD player in use
Setup of the Graphical Remote Control (GRC) unit
For C-V351
ON/STANDBY
MUTE
VOLUME
ENTER
Setup
DVD
Sound
C D
Sat.
Tape1
Cable
Reset
VCR1
VCR2
L D
M D
T V
Confirm
Set Up
Return
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1
TV
Sat.Cable
MD
Main
Menu
DVD
Main
Menu
Main
Menu
ENTER
7 Select the ”Main Menu“ icon.
8 Press the ”ENTER“ key to enter the
selection.
Main
Menu
14
C-V351/C-V301 (EN)
Set Up
Set Up
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
Set Up MD Set Up DVD
÷ Select “System Control” or “IR” ac-
cording to the connected MD recorder
type.
1 Select the ”Set Up“ icon.
2 Press the ”ENTER“ key to enter the
selection.
3 Select the ”MD“ icon.
4 Press the ”ENTER“ key to enter the
selection.
5 Select the ”System Control“ icon.
6 Press the ”ENTER“ key to enter the
selection.
7 Select the ”Main Menu“ icon.
8 Press the ”ENTER“ key to enter the
selection.
1 Select the ”Set Up“ icon.
2 Press the ”ENTER“ key to enter the
selection.
3 Select the ”DVD“ icon.
4 Press the ”ENTER“ key to enter the
selection.
5 Select the ”Main Menu“ icon.
6 Press the ”ENTER“ key to enter the
selection.
÷ Icon
appears at the moment the setup has
completed.
÷ Icons
appear at the moment the setup has
completed.
Setup of GRC according to the
MD recorder in use
Setup of GRC according to the
DVD player in use
Setup of the Graphical Remote Control (GRC) unit
System Control
Main operation menu
For C-V351
ON/STANDBY
MUTE
VOLUME
ENTER
Setup
DVD
Sound
C D
Sat.
Tape1
Cable
Reset
VCR1
VCR2
L D
M D
T V
Confirm
Set Up
Return
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1
TV
Sat.Cable
MD
Main
Menu
DVD
Main
Menu
Main
Menu
DVD
M D
15
C-V351/C-V301 (EN)
1
2
VCR1
1
2
3
4
5
6
7
8
9
0
Set
000
Set Up
ENTER
ENTER
ENTER
Set
431
Setting up the GRC according to other components
(Set Up)
The GRC can also be used to remote control other compo-
nents which are not connected through system control
cords. To control another component, it is required to regis-
ter the setup code corresponding to it beforehand. p
Registering setup codes for VCR 1
Find the setup code of the component to be registered by referring to the Setup code chart in this manual.
Enter the setup code.
1 Select the ”Set Up“ icon.
2 Enter the selection
(by pressing the ”ENTER“ key).
3 Select the ”VCR 1“ icon.
4 Enter the selection
(by pressing the ”ENTER“ key).
5 Enter the setup code.
6 Select the ”Set“ icon.
7 Enter the selection
(by pressing the ”ENTER“ key).
Use the numeric keys as shown below.
Entry examples:
431 .....4
ENTER
3
ENTER
1
ENTER
400 .....4
ENTER
)
ENTER
)
ENTER
Registering setup codes of other components
Registering setup code for VCR 2
Registering setup code for TV
Registering setup code for CABLE
Registering setup code for SATELLITE
Registering setup code for LD player (IR)
The procedure of steps 1 and 2-1 to 7 of “Registering
setup code for VCR 1” also allows to register the compo-
nents listed below to remote control them from the GRC.
Main operation menu
Setup of the Graphical Remote Control (GRC) unit
For C-V351
Check the operation of the component.
1 Display the operation screen of the component to be checked.
2 Turn on the component from the GRC and confirm the
actual component.
÷ If there is more than one setup code, input each code to see
which one turns the power on. That will be the correct code for
your component.
Although each setup code is designed to work with a
number of different models, certain codes may not work
with some models. (Also, certain codes may only operate
some of the functions available on a given model.)
With some models, be sure to keep the ENTER key
pressed for a while.
÷ When a code which is not shown in the setup code chart is entered,
the entered code disappears automatically.
ON/STANDBY
MUTE
VOLUME
ENTER
Setup
DVD
Sound
C D
Sat.
Tape1
Cable
Reset
VCR1
VCR2
L D
M D
T V
Confirm
Set Up
Return
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1
TV
Sat.Cable
MD
Main
Menu
DVD
Note
Note
16
C-V351/C-V301 (EN)
Sound
STEREO
PRO LOGIC
3 STEREO
Source
Direct
Main Menu 1
C D
Tuner
Tape1 / MD
6ch Input
LD / DVD
VCR
AUX
1
1
3
3
Main Menu 2
Display
Tape2 Monitor
Sleep
ENTER
ENTER ENTER
ENTER
ENTER
ENTER
ENTER
Remote control of components from the GRC (For C-V351)
Controlling the AV CONTROL CENTER
The operations required to remote control the AV CONTROL
CENTER includes the INPUT SELECTOR selection, display
mode selection, stereo selection and so on.
The following procedures show how to remote control the
basic operations of the GRC.
Operation examples
Switching the INPUT SELEC-
TOR
(Selecting the CD input)
Switching the display mode
of the AV CONTROL CENTER
Selecting the stereo mode
4 Press the ”ENTER“ key to enter the
selection.
3 Select the ”CD“ icon with the joy-
stick.
1 Select the ”Main Menu“ icon in the
fixed segment screen by operating
the joystick.
2 Press the ”ENTER“ key to enter the
selection.
5 The input source is switched to ”CD“.
÷ Other input than CD can be selected in
step 3.
4 Press the ”ENTER“ key to enter the
selection.
3 Select the ”Main Menu“ icon again.
1 Select the ”Main Menu“ icon in the
fixed segment screen by operating
the joystick.
2 Press the ”ENTER“ key to enter the
selection.
5 Select the ”Display“ icon.
6 Press the ”ENTER“ key to enter the
selection.
÷ It is also possible to select the Tape 2
Monitor or Sleep icon in step 5.
7 Each press of the ”ENTER“ key
switches the display mode.
4 Press the ”ENTER“ key to enter the
selection.
3 Select the ”STEREO“ icon with the
joystick.
1 Select the ”Sound“ icon in the fixed
segment screen by operating the joy-
stick.
2 Press the ”ENTER“ key to enter the
selection.
÷ It is also possible to select the Pro Logic,
3 STEREO or Source Direct icon in step
3.
Main operation menu
For C-V351
ON/STANDBY
MUTE
VOLUME
ENTER
Main Menu 1
C D
Tuner
Tape1 / MD
VCR
AUX
Confirm
Set Up
Return
Input
Source
Main Menu
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1TVSat.Cable
LD / DVD
6ch Input
Confirm
Set Up
Return
Main
Menu
Confirm
Set Up
Return
Main
Menu
Confirm
Set Up
Return
Main
Menu
Confirm
Set Up
Return
Main
Menu
1
17
C-V351/C-V301 (EN)
ENTER
ENTER
C D
CD
ENTER
ENTER
Tuner
ENTER
ENTER
ENTER
Tuner
ENTER
Tuner
Memory /
10key Pad
Auto Band
RDS
01ch
100.00
fm MHz
P.Call
Remote control of components from the GRC
Controlling the components connected through system control cords
When a CD player, cassette deck and/or LD player are
connected with the AV CONTROL CENTER through system
control cords, their system control operations are possible
from the GRC.
Preparations
÷ System control connection 7
÷ Model Type Setup @
÷ Setup of source components #
Main operation menu
Operating the tuner
1 Select the ”Tuner“ input.
2 Display the tuner operation
menu.
3 Select the icon to be operated.
4 Enter the selection
(by pressing the ”ENTER“
key).
÷ Any of the keys which can control the tuner can be selected.
Operating the CD player
1 Select the ”CD“ input.
2 Display the CD operation menu.
3 Select the icon to be operated.
4 Enter the selection
(by pressing the ”ENTER“
key).
÷ Any of the CD player operation keys can be selected.
÷ The menu display shown on the left is an example which appears with
a single CD player.
÷ For the operation of the CD player, also read the instruction manual of
the CD player.
For C-V351
CD
Track 01
10key
Pad
Mode
ON/STANDBY
MUTE
VOLUME
ENTER
Main Menu 1
C D
Tuner
Tape1 / MD
VCR
AUX
Confirm
Set Up
Return
Input
Source
Main Menu
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1TVSat.Cable
LD / DVD
6ch Input
Main
Menu
Main
Menu
18
C-V351/C-V301 (EN)
ENTER
ENTER
ENTER
p
Tape B
CCRS
O.T.E.
ENTER
Tape1 / MD
TapeB
ENTER
ENTER
LD
ENTER
ENTER
Remote control of components from the GRC
Main operation menu
Operating the cassette deck
1 Select the ”Tape 1“ input.
2 Display the cassette deck opera-
tion menu.
3 Select the icon to be operated.
4 Enter the selection
(by pressing the ”ENTER“
key).
Operating the LD player
1 Select the ”LD“ input.
2 Display the LD player operation
menu.
3 Select the icon to be oper-
ated.
4 Enter the selection
(by pressing the
”ENTER“ key).
÷ The procedure on the left is an example assuming that “Dual” has been
selected in the ”Setup“ operation.
÷ In case “Single” was selected in the Setup operation, the ”Tape 1“
icon is displayed.
÷ Any of the cassette deck operation keys can be selected.
÷ For the operation of the cassette deck, also read the instruction manual
of the cassette deck.
÷ Any of the LD player operation keys can be selected.
÷ The procedure on the left is an example assuming that “System
Control” has been selected in the ”Setup“ operation.
÷ For the operation of the LD player, also read the instruction manual of
the LD player.
For C-V351
LD
Track 01
Mode
10key
Pad
Video
CD
ON/STANDBY
MUTE
VOLUME
ENTER
Main Menu 1
C D
Tuner
Tape1 / MD
VCR
AUX
Confirm
Set Up
Return
Input
Source
Main Menu
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1TVSat.Cable
LD / DVD
6ch Input
Main
Menu
Main
Menu
LD / DVD
19
C-V351/C-V301 (EN)
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
Remote control of components from the GRC
Main operation menu
Operating the MD recorder
1 Select the ”MD“ input.
2 Display the MD operation menu.
3 Select the icon to be operated.
4 Enter the selection
(by pressing the ”ENTER“
key).
÷ Any of the keys which can control the MD recorder can be selected.
Operating the DVD player
1 Select the ”DVD“ input.
2 Display the DVD operation menu.
3 Select the icon to be operated.
4 Enter the selection
(by pressing the ”ENTER“
key).
÷ Any of the DVD player operation keys can be selected.
÷ For the operation of the DVD player, also read the instruction manual
of the DVD player.
For C-V351
÷ For the operation of the MD recorder, also read the instruction manual
of the MD recorder.
Main
Menu
MD
MD
10key
PGMPGM
ModeMode
EditEdit
Title SearchTitle Search
Main
Menu
DVD
ON/STANDBY
MUTE
VOLUME
ENTER
Main Menu 1
C D
Tuner
Tape1 / MD
VCR
AUX
Confirm
Set Up
Return
Input
Source
Main Menu
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1TVSat.Cable
LD / DVD
6ch Input
Tape1 / MD
LD / DVD
DVD
(
Scan
)
10key
Mode
SkipSkip
F1
F3
F2
F4
Ret.
20
C-V351/C-V301 (EN)
Remote control with the “RC” unit (For C-V301)
Names and functions of the keys
The “RC” remote control unit provided with the AV CONTROL CENTER can also control KENWOOD cassette decks, CD player
and LD player connected to the AV CONTROL CENTER through system control cords. For details of the controllable functions,
refer to the instruction manuals of these components.
Infrared system
RC-S0506
The RC keys with the same names as the corresponding keys
on the main unit have the same function as the main unit
keys.
3
1
2
9
8
0
7
4
6
5
REMOTE CONTROL UNIT
A B
+10
54321
09876
6
7
8
%
fi
¢4¡
1
¡372
2
1
ALL INFO.TEXT DISP.
TITLE
SEARCH
MEMO
TUNER
BAND
e STILL STEP
E
A.MONI.
AUTO
MEMORY
RDS
DISPLAY
PTY
SEARCH
DISPLAY
SLEEP
NEXTPREV.
POWER
TIME
P.B.C SELECT RETURN FREEZE PAL/NTSC
CLEAR
P.MODE
CHECK
STEREO
MUTE
SOURCE
DIRECTDSP
LEVEL VOLUME
PRO LOGIC 3 STEREO
MULTI
CONTROL
TEST
TONE
MODE
INPUT
TAPE 2
(MONITOR)
TAPE
MD / LD
REC/ARMO.T.E.
LD
AUTO DIGITAL
CD/VIDEO CD/LD
REPEAT
FRAME/
TIME
PTY
TA/NEWS/INFO.
DISC SKIPEDIT MODE
ALL TEXT
SEARCH
P.CALL
fi%
7
¢48
3
°
1 (POWER) key
Press to switch the AV CONTROL CENTER
and the components connected to it through
system control cords between ON and
STANDBY.
2 A j B switch
Some of the RC keys function in two ways.
The key functions indicated inside ( ) are
usable when this switch is set to B.
Usually set this switch to A. In this manual,
the description of a function which re-
quires this switch to be set to B is accom-
panied with the illustration of
.
3 Numeric keys
Use these keys as the numeric key of the
currently selected input source component.
4 TUNER operation keys
BAND key
(RDS DISPLAY key)
MEMO key
(AUTO MEMORY key)
P.CALL fi:down key
(PTY key)
P.CALL %:up key
(TA/NEWS/INFO. key)
5 LD player operation key
Read the instruction manual of the LD player.
° :CX key
AUTO DIGITAL key
6 AV CONTROL CENTER operation keys
PRO LOGIC key
3 STEREO key
DSP key
STEREO key
SOURCE DIRECT key
TEST TONE key
MODE key
Use this key to select the setting modes.
MULTI CONTROL LEVEL
: up key, : down key
Use these keys to adjust the tone or set the
surround play.
TAPE 2 (MONITOR) key
INPUT key
Use this key as the input selector key.
MUTE key
Use this key to mute the sound temporarily.
VOLUME %: up key, fi: down key
Use these keys to adjust the volume.
7 Key
SLEEP key
Press when setting the sleep timer.
DISPLAY key (LD DISPLAY key)
Press to switch the displayed information.
8 CD/VIDEO CD/LD player operation
keys
Read the instruction manuals of the CD player,
VIDEO CD player and/or LD player.
TITLE SEARCH key
(A.MONI key)
TEXT DISP. key
(STILL STEP e key)
ALL INFO. key
(STILL STEP E key)
ALL TEXT SEARCH key
(FRAME/TIME key)
EDIT MODE key
DISC SKIP key
(REPEAT key)
1 key
¡ key
4 key (PREV.)
¢ key (NEXT)
6 key
P.MODE key
CHECK key
CLEAR key
TIME key
7 key
9 MD/LD player-specific operation keys
Read the instruction manual of the MD re-
corder and LD player.
4 key (P.B.C. key)
¢ key (SELECT key)
7 key (RETURN key)
8 key (FREEZE key)
3 key (PAL/NTSC key)
Loading batteries
0 Cassette deck operation keys
Read the instruction manual of the cassette
deck.
( REC/ARM key)
8 key
1 key
2 key
7 key
3 key
¡ key
(O.T.E. key)
÷ Insert two AA-size (R6/SUM-3) batteries as indicated by the polarity marking.
1 Slide open the cover. 2 Insert batteries. 3 Close the cover.
For C-V301
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Kenwood C-V301 User manual

Kenwood
Brand
Kenwood
Model
C-V301
Category
AV receivers
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents