MIMAKI TPC-1000 Operating instructions
- Category
- Inkjet printers
- Type
- Operating instructions
Supplement for the Basic Operation manual
補足説明書
MIMAKI ENGINEERING CO., LTD.
From the firmware Ver. 3.20, the function below were added.
Please read this manual and fully understand it before using the device.
If you have any question, contact your local distributor.
ファームウェア Ver.3.20 より、次の機能が追加になりました。
本書をお読みになり、十分理解してからご使用ください。
ご不明な点は、販売店または弊社営業所までご連絡ください。
This manual correspond to the models as firmware version 3.20 or later.
When turning on the power, you can confirm the firmware version.
本書は、ファームウェア Ver.3.20 以降の機種に対応しています。
ファームウェアのバージョンは、電源をオンにした際に確認できます。
D202674-10
Perform setting to reduce stripes between passes ........................................................... 2
To customer using sublimation transfer ink Sb53 ............................................................. 3
Changed contents common to all machine types .............................................................. 3
パス間のシマを軽減する設定をする ....................................................................................... 4
昇華転写インク Sb53 をお使いのお客様へ ............................................................................ 5
機種共通変更内容 ................................................................................................................... 5
ENGLISH
日本語
2
Perform setting to reduce stripes between passes
In case that feeding stripes cannot be resolved even though media correction is performed, make “MAPS
(Mimaki Advanced Pass System) valid. Feeding stripes become less visible by distributing the pass boundary.
1
Press the key in LOCAL.
2
Press the key.
3
Press the key.
4
Press to select [MAPS].
5
Press the key.
6
Press to set ON/OFF.
• Set Value : OFF, ON
7
Press the key.
• When you select OFF, proceed to the Step 9.
• MAPS effect differs depending on the set value of the printing speed. Use it after checking effect in
advance.
• When you speed up the printing speed, it takes shorter time to print. However, MAPS effect becomes
weak.
• When you slow down the printing speed, it takes longer time to print. However, MAPS effect becomes
strong and feeding stripes become less visible.
• The resolutions and passes for which MAPS is enabled are shown in the following table.
• For conditions when MAPS is disabled, the printer operates with MAPS-OFF and print speed settings
disabled (±0%).
• MAPS may not be effective depending on image to be printed.
• Slight color change may be found.
Resolution
(dpi)
Pass
4 colors 6/ 7/ 8 colors
△○◎△○◎
540x720 2 4 8, 16 816, 32
540x1080
6 12, 24 12 24, 48
720x720
4 8, 16 816, 32
720x1080 6 12, 24 12 24, 48
720x1440
8 16, 32 16 32, 64
◎ : MAPS can be used when the print speed setting is within a range of ±50%, for both high speed and
standard speed.
○ : At high speed, print speed is within the range of -50% to -1%. At standard speed, MAPS can be used
when the print speed is within a range of ±50%.
△ : MAPS can be used when the print speed setting is within the range of -50% to -1% at standard speed
only.
FUNCT I ON
SETUP <ENT>
SETUP
SELECT : TYPE . 1
[1]
MED I A COMP . < e n t >
[1]
MA P S < e n t >
[ 1 ] MAPS
SETUP : OFF
[ 1 ] MAPS
SETUP : ON
[ 1 ] MAPS
PR I NT SPEED : 0%
To customer using sublimation transfer ink Sb53
3
8
Press to change print speed.
• Set Value : -50 ~ +50%
(If +20% is entered, the print speed increases by
approximately 20%. If -20% is entered, the print speed
decreases by approximately 20%.)
9
Press the key.
10
Press the key several times to end the setting.
To customer using sublimation transfer ink Sb53
“Deep black” was newly added to ink colors of sublimation transfer ink Sb53.
With this, we made it can be recognize at the machine side. At initial filling, determine whether you use black or
deep black. You cannot change on the way.
Deep black product No. : SB53-DK-44-1(440m cartridge)
: SB53-DK-2L-1(2000ml ink pack)
Changed contents common to all machine types
Stop timer setting of deodorize fan/ drier fan
In the machine setting, we changed stop timer setting of deodorize fan/ drier fan from setting by 10 min. to by 1
min. The range of 0 to 240 has not been changed.
Cleaning intervals setting when AUTO CLEANING/ Print CLEANING is “ON”
In the user type setting, we changed max. value of cleaning intervals setting range when AUTO CLEANING/
Print CLEANING is “ON” from 10000mm to 30000mm. The default value (1000mm) has not been changed.
Item Set value Outline
Machine Setup
DEODORIZE
FAN
STOP TIME
0 ~ 120
~ 240min/
CONTINUE
Setting the time until the rotation of the exhaust
fan is interrupted after the completion of printing.
RENEW ON / OFF
Switching the current operation of the exhaust
fan.
Function name Set value Outline
AUTO
CLEANING
ON
INTERVAL 10 ~ 1000
~ 30000 mm
Sets the auto cleaning of the
print head every completion
of printing.
TYPE NORMAL
/ SOFT / HARD
OFF
Print.
CLEANING
ON
INTERVAL 10 ~ 1000
~ 30000 mm
Sets the auto cleaning of the
print head in printing.
TYPE NORMAL
/ SOFT / HARD
OFF
[1]MAPS
PR I NT SPEED : 1 0%
[1]
MAP S < e n t >
Page is loading ...
Page is loading ...
D202674-10-24012014
All Rights Reserved.
© MIMAKI ENGINEERING CO., LTD. NH
-
1
-
2
-
3
-
4
-
5
-
6
MIMAKI TPC-1000 Operating instructions
- Category
- Inkjet printers
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
MIMAKI CJV30BS Operating instructions
-
-
-
-
-
-
-
-
-
