Inventum NB560R Owner's manual

blender drinkﬂes to-go

BLENDER TO

-

GO BOTTLE

•

BLENDER TRINKFLASCHE TO GO

NB560R

• gebruiksaanwijzing

• instruction manual

• gebrauchsanleitung

• mode d’emploi

•

MIXEUR BIDON TO

-

GO

1. veiligheidsvoorschriften pagina 3

2. product omschrijving pagina 5

3. voor het eerste gebruik pagina 5

4. het gebruik van de blender met de glazen mengbeker pagina 6

5. het gebruik van de blender met de drinkﬂes to-go pagina 6

6. tips pagina 6

7. reiniging & onderhoud pagina 7

Algemene service- en garantievoorwaarden pagina 24

1. safety instructions page 8

2. appliance description page 10

3. before ﬁrst use page 10

4. using the blender with the glass blender jug page 11

5. using the blender with the to-go bottle page 11

6. tips page 11

7. cleaning & maintenance page 12

General terms and conditions of service and warranty page 25

Nederlands

English

1. Sicherheitshinweise Seite 13

2. Beschreibung des Geräts Seite 15

3. vor der Inbetriebnahme Seite 15

4. der Gebrauch des Blenders mit Gläserner Mischbecher Seite 16

5. der Gebrauch des Blenders mit Trinkﬂasche to go Seite 16

6. Tips Seite 16

7. Reinigung & Pﬂege Seite 17

Allgemeine Service- und Garantiebedingungen Seite 26

1. consignes de sécurité page 18

2. déﬁnition de l’appareil page 21

3. pour la première utilisation page 21

4. l’utilisation du mixeur avec le bol mélangeur page 22

5. l’utilisation du mixeur avec le bidon to-go page 22

6. conseils importants page 22

7. nettoyage & entretrien page 23

Conditions générales de garantie et de service après-vente page 27

Deutsch

Français

2 •

Page is loading ...

English

safety instructions

1

• Please read these instructions before operating the appliance

and retain for future use.

• The appliance is intended solely for domestic use within the home.

• The appliance is not intended to be operated by means of an external

timer or seperate remote-control system.

• Before cleaning and storing allow the appliance and the cooking plates

to cool completely.

• Before plugging into a socket, check whether the voltage in your home

corresponds with the voltage printed at the bottom of the appliance.

• Never let the power cord of the appliance hang over the edge of a

table or counter, touch hot surfaces or become knotted.

• Never place this appliance on or near a hot gas or electric burner or in

such a place where it could touch a heated oven or microwave. Do not

allow this appliance to come in contact with curtains, wall coverings,

clothing, dishtowels or other ﬂammable materials during use.

• Always use the appliance on a secure, dry, level surface.

• Never leave the appliance unattended when in use.

• Always carry out regular checks of the power cord to ensure no

damage is evident. Should there be any signs of damage to the power

cord in the slightest degree, the entire appliance should be returned to

the Customer Service Department.

• For your own safety, only use the accessories and spare parts from the

manufacturer which are suitable for the appliance.

• Always return the appliance after a malfunction, or if it has been

damaged in any manner to the Customer Service Department for

examination, repair or adjustment as special purpose tools are

required.

• Never unplug it from the socket by pulling the cable.

• Always ensure that your hands are dry before handling the plug or

power cord.

• An electrical appliance is not a toy and should therefore always be

placed outside of the reach of children. Children are not always able

to understand potential risks. Keep the appliance and its cord out of

reach of children less than 8 years.

• This appliance may be used by children over the age of 8 and by

people with reduced physical, sensory or mental skills or a lack of

experience or knowledge, provided that they are supervised or have

been instructed on how to use the appliance safely, and are fully aware

8 • English

English • 9

of the consequent risks of use.

• Children must not play with the appliance.

• Cleaning and user maintenance must not be performed by children

unless supervised.

• Unplug the appliance as soon as you have ﬁnished using it and when

you are cleaning it.

• If an extension cord is used, compare the marked electrical rating

of the extension cord with the electrical rating on the appliance.

Make sure that it can not be pulled by children or tripped over

unintentionally.

• Should you decide not to use the appliance anymore, make it

inoperative by cutting the power cord after removing the plug from

the socket. We also recommend making all potentially dangerous

parts of the appliance harmless, particularly for children who might be

tempted to play with them.

• Never use the appliance if it is not working properly, or if it has

been damaged. Any intervention other than cleaning and normal

maintenance by the customer must be carried out by an approved

Service Centre.

• Never immerse any part of the main body, power cord and

plug into water or any other liquid to protect yourself against

electrical hazards.

• When the appliance is used for other purposes than intended, or is

when it is not handled in accordance with the instruction manual,

the full responsibility for any consequences will rest with the user.

Any damages to the product or other things are not covered by the

warranty.

• Legislation requires that all electrical and electronic equipment

must be collected for reuse and recycling. Electrical and

electronic equipment marked with the symbol indicating

separate collection of such equipment must be returned to a

municipal waste collection point.

appliance description

2

before ﬁrst use

3

Before you use the appliance for the ﬁrst time, please do as follows: Carefully unpack the appliance and remove all the packaging

material. Keep the material (plastic bags and cardboard) out of reach of children. Check the appliance after unpacking for any

damage, possible from transportation. Place the blender on a ﬂat and stable surface. Rinse all the accessories - glass blender jug,

to-go bottle, blade sets and both lids - with warm soapy water and dry them thoroughly. Wipe the base with a damp cloth. Always roll

out the cord completely.

When the blender is in use, the ingredients will be transported along the sides of the jug to the top and will come down through the

middle. This system guarantees that even ice cubes will be completely crushed in the glass blender jug.

• Place the blender on a ﬂat and stable surface as soon as you have rolled out the cord. Practice a few times to disassemble and

assemble the blender without any ingredients.

• The middle of the lid of the glass jug has a cap which can be used as a measuringcup and for adding ingredients. Through the

opening in the lid you can gradually add ingredients.

• The base contains the motor. Because of it’s size, the housing is very stable.

• The control knob regulates the speed of the blender. The blender has 2 speeds and a pulse (ice crush) setting.

- setting P = pulse

- setting O = off

- setting 1 = lowest speed

- setting 2 = highest speed

• The blender can crush ice cubes with the pulse setting in the glass blender jug. This means that the blender is only activated when

you turn the knob to the pulse setting. As soon as you let go of the button the blender will be deactivated.

10 • English

1. Filler cap

2. Lid

3. Glass blender jug (capacity 1 litre)

4. Control knob with speed settings

5. Base

6. Blade set

4

2

1

3

5

NB560R

7. Lid with drinking spout

8. Bottle (capacity 600 ml)

9. Blade set

7

8

9

6

using the blender with the glass blender jug

4

English • 11

Before plugging into a socket, check that the voltage in your home corresponds with the voltage printed on the bottom of the

appliance.

1. Place the blender on a ﬂat, clean and dry surface.

2. Make sure that the blender is not activated.

3. Put the ingredients in the glass jug and lock it with the lid.

4. Switch the blender on by selecting a position with the position button.

Attention: Do not activate the mixer constantly, this can cause engine problems. Do not use the mixer for more then 1 minute

continuously, wait 1 minute before you operate it again.

5. When the blender has ﬁnished mixing switch the button to off (0) and wait until the blades have stopped turning., before you

remove the glass blender jug.

tips

6

• When the glass blender jug is cracked, do not use the mixer anymore. This could lead to damage while using the mixer.

• To avoid splashes always place the lid on the blender jug.

• Always add liquid ingredients before adding solid ingredients in the mixer.

• The mixer mixes best when you do not add pieces which are too large.

• Always add a half a cup of liquids when you crush ice cubes. Attention: Only crush ice cubes in the glass blender jug.

• To add ingredients while the mixer is activated, take the cap out of the lid and add the ingredients through the opening.

• When the ingredients stick to the sides of the glass jug or are not mixed properly, shut off the engine: wait until the knives have

stopped turning and push the ingredients with a spatula towards the knives.

• To prevent the ingredients from being blend to small, take into account that the mixer mixes in seconds, not minutes!

• Working with warm ingredients can cause a build-up of pressure in the jug and that can cause hot liquids to escape when you take

the lid of the glass jug. Therefore always remove the cap from the lid when you are processing warm ingredients.

using the blender with the to-go bottle

5

Before plugging into a socket, check that the voltage in your home corresponds with the voltage printed on the bottom of the

appliance.

1. Place the blender on a ﬂat, clean and dry surface.

2. Make sure that the blender is not activated.

3. Put the ingredients in the bottle and lock it by ﬁrmly turning on the blade set. Turn the drinks bottle around and place it upright on

the motor base unit. Make sure that the  indications are in line and click the bottle tight by turning it slightly to the left.

4. Switch the blender on by selecting a position with the position button. Attention: Do not activate the mixer constantly, this can

cause engine problems. Do not use the mixer for more then 1 minute continuously, wait 1 minute before you operate it again.

5. When the blender has ﬁnished mixing switch the button to off (0) and wait until the blades have stopped turning.

6. Click the bottle loose - do not turn too far - and lift it from the motor base unit. Attention: if you turn the bottle too far you turn

the bottle off the blade set and the contents will ﬂow out of the bottle.

7. Turn the drinks bottle around, remove the blade set and ﬁrmly turn the lid with drinking spout onto the drinks bottle. You’re ready to

go!

Attention: you cannot crush ice cubes or make warm dishes in the to-go drinks bottle.

12 • English

cleaning & maintenance

7

Always unplug the cord from the socket before cleaning the appliance.

• Wipe the base with a damp cloth. Do not use any abrasive or strong detergents.

• Never place the appliance, the power cable or the plug in water or any other liquid.

• Remove the blade set according to the instructions below. Be careful, the blade sets are extremely sharp. Clean the blade sets as a

whole do not try to take them apart. Attention: do not use any abrasive or strong detergents.

For placing and removing the blade set you need the glass blender jug and the blade set. Place the glass blender jug, without the lid,

upside down on a ﬂat stable surface. You are now able to remove the blade set.

To replace the blade set follow the instructions in the reverse order.

• The parts described below may be washed:

- glass blender jug

- to-go bottle

- blade sets

- lid with ﬁller cap

- lid with drinking spout

Page is loading ...

English • 25

We do not need to remind you of the importance of service. After all, we develop our products to a standard so that you

can enjoy them for many years, without any concerns. If, nevertheless, there is a problem, we believe you are entitled to a

solution straight away. Hence our products come with an exchange service, on top of the rights and claims you are entitled to

by law. By exchanging a product or part, we save you time, effort and costs.

2-year full manufacturer’s warranty

1. Customers enjoy a 2-year full manufacturer’s warranty on all Inventum products. Within this period, a faulty product or part will

always be exchanged for a new model, free of charge. In order to claim under the 2-year full manufacturer’s warranty, you can either

return the product to the shop you bought it from or contact the Inventum costumer service department via the form at www.

inventum.eu/service-aanvraag.

2. The 2-year warranty period starts from the date the product is bought.

3. In order to claim under the warranty, you must produce a copy of the original receipt.

4. The warranty applies only to normal domestic use of Inventum products within the Netherlands.

Breakdowns or faults outside the warranty period

1. Breakdowns or faults in small or large domestic appliances outside the warranty period, can be reported to the costumer services

department via the form at www.inventum.eu/service-aanvraag or by calling the costumer services department.

2. The costumer services department may ask you to send the product for inspection or repair. The costs of dispatch will be at your

expense.

3. The inspection to establish whether repair is possible involves a charge. You need to grant your permission for this, in advance.

4. In the event of a large domestic appliance, Inventum, at your request, can send out a service engineer. In that case, you will be

charged the call-out costs, as well as parts and labour.

5. In the event of an instruction to repair, the repair costs must be paid in advance. In the event of a repair by a service engineer, the

costs of the repair must be settled with the engineer onsite, preferably by means of PIN payment.

Warranty exclusions

1. The following is excluded from the aforesaid warranties:

• normal wear and tear;

• improper use or misuse;

• insufﬁcient maintenance;

• failure to comply with the operating and maintenance instructions;

• unprofessional installation or repairs by third parties or the customer himself;

• non-original parts used by the customer;

• use for commercial or business purposes;

• removal of the serial number and/or rating label.

2. In addition, the warranty does not apply to normal consumer goods, such as:

• dough hooks, baking tins, (carbon) ﬁlters, etc.;

• batteries, bulbs, carbon ﬁlters, fat ﬁlters etc.;

• external connection cables;

• glass accessories and glass parts such as oven doors;

• and similar items.

3. Transport damage not caused by Inventum is also excluded. Therefore, inspect your new device before starting to use it. If you

detect any damage, you must report this to the store where you purchased the product within 5 working days, or to the Inventum

customer service department via the form at www.inventum.eu/service-aanvraag. If transport damage is not reported within this

period, Inventum does not accept any liability in this respect.

4. The following are excluded from warranty and/or replacement: faults, loss of and damage to the device as a result of an event that

is normally insured under the home contents insurance.

Important to know

1. The replacement or repair of a faulty product, or a part thereof, does not lead to an extension of the original warranty period.

2. If a complaint is unfounded, all costs arising from it will be at the customer’s expense.

3. Following expiry of the warranty period, all costs of repair or replacement, including administration costs, dispatch and call-out

charges, will be charged to the customer.

4. Inventum cannot be held liable for damage caused by external events, unless this liability arises from mandatory statutory

provisions.

5. These warranty and service provisions are governed by Dutch law. Disputes will be settled exclusively by the competent Dutch

court.

general terms and conditions of service and warranty

Page is loading ...

NB560R/01.0516V

Wijzigingen en drukfouten voorbehouden/ Änderungen und Druckfehler vorbehalten/

Sous réserve de modiﬁcation / Modiﬁcations and printing errors reserved

Inventum Huishoudelijke

Apparaten B.V.

Meander 861

6825 MH Arnhem

T 0800 -4583688

info@inventum.eu

www.inventum.eu

twitter.com/inventum1908

facebook.com/inventum1908

youtube.com/inventum1908

persoonlijke verzorgingklein huishoudelijk witgoed inbouwwitgoed vrijstaand

Inventum NB560R Owner's manual

Inventum NB560R Owner's manual

in other languages

Related papers

Other documents