STEP SYSTEMS 23050 User manual
- Category
- Measuring, testing & control
- Type
- User manual
Item-no. 23050
Pocket Multi-Tester
User Manual
Pocket Multi-Tester
User Manual
All rights reserved.
Printed in Germany.
STEP Systems GmbH 2017
Duisburger Str. 44
Tel: ++49 (0) 911 96 26 05-0
Fax: ++49 (0) 911 96 26 05-9
D-90451 Nürnberg
e-mail: info@stepsystems.de
www.stepsystems.de
General information
The contents of this manual were carefully verified and have been compiled
to the best of our knowledge. However, the Manufacturer does not accept
liability for possibly contained statements in this manual. In no event will the
manufacturer be liable for direct, indirect, special, incidental or
consequential damages resulting from any defect or omission in this
manual. The manufacturer reserves the right to make changes in this
manual and the products it describes at any time, without notice or
obligation. Revised editions can be found on the manufacturer’s website.
Declaration of Conformity:
This device complies with the EMC Directives 89/336/EEC,
2004/108/EF, 73/23/EEC and 2004/22/EF, EN60065,
EN55022 Class B, EN55024, EN6100-3-2, EN292 and EN 60335.
Legal Obligation for battery disposal: Batteries do not belong in
household waste. As consumer, you are legally obliged to return used
batteries. You can bring your old batteries to public collection points in
your community or anywhere else where batteries of this type are sold.
Note: these characters can be found on batteries containing pollutants:
Pb = battery contains lead - Cd = battery contains cadmium
Hg = battery contains mercury
Pocket Multi-Tester
User Manual
All rights reserved.
Printed in Germany.
STEP Systems GmbH 2017
Duisburger Str. 44
Tel: ++49 (0) 911 96 26 05-0
Fax: ++49 (0) 911 96 26 05-9
D-90451 Nürnberg
e-mail: info@stepsystems.de
www.stepsystems.de
Technical features:
- large LCD display
- measuring parameters: pH / mV / COND / TDS / SALT / °C
- confirmation when a stable measured value is reached with icon
on the display
- automatic temperature compensation
- calibration on 1, 2 or 3 points
Measurement range: рН: -2 - 16; ЕС: 0 - 20 mS; mV: ±1000;
TDS: 0.1 ppm - 10 ppt; S: 0.01...10g/l; t: 0..+50°C
Redox: ± 1000 mV
Resolution: pH: 0.01; t: 0.1°C; ЕС, SALT: automatic
Accuracy: pH: ± 0.01, EC: ±1%; TDS: ±1%; t: ± 0.2 °C
Calibration: рН/ЕС: 1, 2 or 3-point calibration
Temperature
compensation: automatic
Power: 4 batteries x 1.5V AAA, > 200 h
Automatic switch-off: after 8 min
Display: LCD, multi-color backlight
Housing: splash-proof
Protection class: IP 67
Dimensions: 35 x 175 mm: Ø х L (inst.), 29 x 25 x 6 cm (case)
Weight: 130 g (instrument), 0.9 kg (complete case)
Warranty: 2 years for the instrument,
6 months for the electrode
Pocket Multi-Tester
User Manual
All rights reserved.
Printed in Germany.
STEP Systems GmbH 2017
Duisburger Str. 44
Tel: ++49 (0) 911 96 26 05-0
Fax: ++49 (0) 911 96 26 05-9
D-90451 Nürnberg
e-mail: info@stepsystems.de
www.stepsystems.de
Instrument description
1. Battery compartment
2. Battery status indicator
3. Unit
4. Temperature indication
5. Measurement parameter
6. Stability indicator
7. Buffer/calibration solution
8. ON/OFF and Escape
9. MODE
10. Calibration button CAL
11. Replaceable sensor
Pocket Multi-Tester
User Manual
All rights reserved.
Printed in Germany.
STEP Systems GmbH 2017
Duisburger Str. 44
Tel: ++49 (0) 911 96 26 05-0
Fax: ++49 (0) 911 96 26 05-9
D-90451 Nürnberg
e-mail: info@stepsystems.de
www.stepsystems.de
Start-up
Insert the battery
Open the battery compartment. Insert the four AAA 1.5 Volt batteries
with correct polarity. Close the battery compartment.
Switch on
Press the ON / OFF (8) button to turn on the instrument.
Calibration
Calibration of the device is possible by buffer solutions for up to 3
calibration points. We recommend at least 2-points calibration for optimal
measuring results!
Before you start calibration of the Multi-Tester, fill the two measuring cups
with the amount of buffer solution you need.
Now press the CAL button (10) to enter the calibration modes. The display
shows CAL for approx. 2 sec. After that you can immerse the probe in the
first buffer solution pH7 (green). The device automatically detects the
calibration point and stabilizes the measurement.
After a stable value is reached, a Smiley icon appears on the display. Press
the CAL button (10) again and the probe calibrates independently to the
first value.
Pocket Multi-Tester
User Manual
All rights reserved.
Printed in Germany.
STEP Systems GmbH 2017
Duisburger Str. 44
Tel: ++49 (0) 911 96 26 05-0
Fax: ++49 (0) 911 96 26 05-9
D-90451 Nürnberg
e-mail: info@stepsystems.de
www.stepsystems.de
Before proceeding with the pH4 (red) buffer solution, please neutralize the
probe: rinse it with distilled water and wipe it with a piece of cloth.
Repeat as before. After the calibration has been carried out on the second
point, the third point can be calibrated directly, or you can exit the CAL
mode by pressing ESC (8). This takes you directly to the measuring mode.
EC calibration is identical, here only first you should switch to the
measuring range COND using the MODE button (9). Depending on the
use, the Multi-Tester should be calibrated daily before starting a
measurement session, or - when not used frequently - always before a
measurement!
Measurement
Press the ON / OFF button (6) to switch the Multi-Tester on. In the
measurement mode the display is blue. Press MODE (9) to select the
desired measurement value. Insert the sensor then into the solution or
product to be measured and wait until the value is stabilized and
appears. Now you can read the value on the display and select another
measuring value or proceed with the measurement in further liquids or
products.
However, we recommend to neutralize the sensor shortly in water between
measurements in order to avoid falsifying of results.
Clean the sensor after each measurement session with distilled water. Put
a few drops storage solution or buffer solution pH4 in the protective cap
and put on the cap.
Attention: do never store the electrode in distilled water!
Pocket Multi-Tester
User Manual
All rights reserved.
Printed in Germany.
STEP Systems GmbH 2017
Duisburger Str. 44
Tel: ++49 (0) 911 96 26 05-0
Fax: ++49 (0) 911 96 26 05-9
D-90451 Nürnberg
e-mail: info@stepsystems.de
www.stepsystems.de
Measurement parameters
Press the MODE button (9) to choose between the parameters:
pH / mV / COND / TDS / SALT / °C
The mV function helps to prove the pH sensor. A new pH electrode
stabilizes rapidly and shows about 0 mV at pH 7.00, and about 170 mV at
pH 4.00. If the difference between the two values is less than 140 mV and
the electrode reacts very slowly, it must be replaced.
Display light
The display has a backlight in three different colors (blue, green and red)
which change depending on the mode. The light also switches on for about
6 seconds after short pressing of the ON / OFF button (8).
Blue light = normal measurement mode
Green light = calibration mode
Red light = instrument or sensor fault
Switch OFF / Auto Power OFF
Press the ON / OFF button (8) for approx. 5 seconds to switch off the
device.
The meter will automatically turn off 8 minutes after the last press of a key.
Battery replacement / Battery status indication
An indication in the display shows the battery status.
You can also operate the Multi-Meter with rechargeable batteries (see also
“Insert the battery”).
Pocket Multi-Tester
User Manual
All rights reserved.
Printed in Germany.
STEP Systems GmbH 2017
Duisburger Str. 44
Tel: ++49 (0) 911 96 26 05-0
Fax: ++49 (0) 911 96 26 05-9
D-90451 Nürnberg
e-mail: info@stepsystems.de
www.stepsystems.de
Setup mode
Press and hold the CAL button (10). Additionally, press ON/OFF (8). A full-
segment test appears in the display. After releasing the CAL button, "t.u"
appears in the display and °C flashes. Now you can choose between °C &
°F by pressing the MODE button (9).
Press the CAL button (10) again to confirm the desired setting, then the
instrument changes to the RESET mode. The Multi-Tester can be reset to
factory settings by pressing the MODE button (9).
no/rSt = keep the settings
YES/rSt = reset to factory settings
By pressing the CAL button (10) again you save the settings and leave the
setup menu.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
STEP SYSTEMS 23050 User manual
- Category
- Measuring, testing & control
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
ISPRING TDS2 User manual
-
LG PH4R Owner's manual
-
Bante Instruments TDSscan20 Pocket TDS Tester Owner's manual
-
BANTE TDSscan20 User manual
-
Gossen MetraWatt METRAOHM 413 Owner's manual
-
-
-
Oakton WD-35634-12 Owner's manual
-
-
