7 / EN
Washing Machine / User’s Manual
2.5 Connecting to the drain
• Theendofthedrainhosemustbedirectlyconnectedto
thewastewaterdrainortothewashbasin.
A WARNING
Donotremovethetransportationlocksbeforetakingoutthe
packaging reinforcement.
• Thehoseshouldbeattachedtoaheightofatleast40cm,
and100cmatmost.
• Incasethehoseiselevatedafterlayingitonthefloorlevel
orclosetotheground(lessthan40cmabovetheground),
waterdischargebecomesmoredifficultandthelaundry
may come out excessively wet. Therefore, follow the
heightsdescribedinthefigure.
100cm
40cm
• Topreventflowingofdirtywaterbackintothemachineand
to allow for easy discharge, do not immerse the hose end
into the dirty water or do not drive it in the drain more than
15cm.Ifitistoolong,cutitshort.
• Theendofthehoseshouldnotbebent,itshouldnotbe
steppedonandthehosemustnotbepinchedbetweenthe
drain and the machine.
• Ifthelengthofthehoseistooshort,useitbyadding
an original extension hose. Length of the hose may not
belongerthan3.2m.Toavoidwaterleakfailures,the
connectionbetweentheextensionhoseandthedrain
hoseoftheproductmustbefittedwellwithanappropriate
clamp as not to come off and leak.
2.6 Adjusting the feet
A WARNING
Inordertoensurethattheproductoperatesmoresilentlyand
vibration-free,itmuststandlevelandbalancedonitsfeet.Balance
themachinebyadjustingthefeet.Otherwise,theproductmay
movefromitsplaceandcausecrushingandvibrationproblems.
Loosenthelocknutsonthefeetbyhand.Adjustthefeetuntil
theproductstandslevelandbalanced.Tightenalllocknuts
againbyhand.
A WARNING
Donotuseanytoolstoloosenthelocknuts.Otherwise,theywill
get damaged.
2.7 Electrical connection
Connecttheproducttoagroundedoutletprotectedbya13
Afuse.Ourcompanyshallnotbeliableforanydamages
that will arise when the product is used without grounding in
accordance with the local regulations.
• Connectionmustcomplywithnationalregulations.
• Powercableplugmustbewithineasyreachafter
installation.
• Ifthecurrentvalueofthefuseorbreakerinthehouseis
lessthan13Amps,haveaqualifiedelectricianinstalla13
Amp fuse.
• Thevoltagespecifiedinthe“Technicalspecifications”
sectionmustbeequaltoyourmainsvoltage.
• Donotmakeconnectionsviaextensioncablesormulti-
plugs.
B
WARNING: Damagedpowercablesmustbe
replacedbytheAuthorizedServiceAgents.
Electrical requirements
Beforeyouinserttheplugintothewallsocketmakesure
thatthevoltageandthefrequencyshownintheratinglabel
corresponds to your electricity supply.
Werecommendthatthisappliancebeconnectedtothemains
supplyviaasuitableswitchedandfusedsocketinareadily
accessibleposition.
Shouldthemainsleadoftheappliancebecomedamagedor
needreplacingatanytime,itmustbereplacedbyaspecial
purposemademainsleadwhichcanonlybeobtainedfroma
Authorised Service Agent.
B
WARNING: Thisappliancemustbeearthed
Ifthefittedmouldedplugisnotsuitableforyoursocket,then
theplugshouldbecutoffandanappropriateplugfitted.
Destroytheoldplug,whichiscutoffasaplugwithabared
cord could cause a shock hazard if inserted into a socket
elsewhere in the house.
Themouldedplugonthisapplianceincorporatesa13A
fuse.ShouldthefuseneedtobereplacedanASTAapproved
BS1362fuseofthesameratingmustbeused.Donotforget
torefitthefusecover.Intheeventoflosingthefusecover,
theplugmustnotbeuseduntilareplacementfusecoverhas
beenfitted.Colourofthereplacementfusecovermustbethe
samecolourasthatvisibleonthepinfaceoftheplug.Fuse
coversareavailablefromanygoodelectricalstore.
Important
Fitting a different plug
As the colours of the wires in the mains lead of this appliance
may not correspond with the coloured markings identifying
the terminals on your plug, proceed as follows:
1 Connectthegreen-yelloworgreen(earth)wiretothe
terminalintheplugmarked‘E’orwiththesymbolfor
coloured green and yellow or green.
2 Connecttheblue(neutral)wiretotheterminalintheplug
marked‘N’orcolouredblack.
3 Connectthebrown(live)wiretotheterminalintheplug
marked ‘L’ or coloured red.
Withthealternativeplugsa13Afusemustbefittedeither
intheplugoradaptororinthemainfusebox.Ifindoubt
contactaqualifiedelectrician.