Troy-Bilt 24BL59M5711 User manual

Brand: Troy-Bilt

Model: 24BL59M5711

Type: User manual

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

Printed In USA

Safe Operation Practices • Set-Up • Operation • Maintenance • Troubleshooting • Warranty

WARNING

READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

OperatOr’s Manual

277cc, 357cc & 420cc OHV Horizontal Shaft Engine

Form No. 769-06053E

(September 3, 2014)

This Operator’s Manual is an important part of your new engine. It will help you prepare and maintain the engine for the best

performance. Please read and understand the contents before operating the engine.

Thank You

Customer Support

Please do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department.

If you have difficulty with this product or have any questions regarding the controls, operation, or maintenance of this

engine, you can seek help from the experts. Choose from the options below:

◊ Visit us on the web at www.mtdproducts.com

See How-to Maintenance and Parts Installation Videos at www.mtdparts.com/KnowledgeCenter

◊ Call a Customer Support Representative at (800) 800-7310 or (330) 220-4683

◊ Write us at MTD LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019

Model NuMber/Serial NuMber

Record Product Information

Before operating your new engine, please locate the model plate

on the engine and record the information in the provided area

to the right. This information will be necessary, should you seek

technical support via our web site or with your local dealer.

To The Owner

Safe Operation Practices ........................................ 3

Safety Symbols ........................................................ 5

Set-Up ....................................................................... 6

Controls & Features ................................................. 9

Operation ................................................................10

Maintenance ...........................................................13

Troubleshooting .....................................................19

Replacement Parts ................................................ 20

Emission Statement/Warranty .............................21

Spanish ................................................................... 23

Table of Contents

Important Safe Operation Practices

WARNING! This symbol points out important safety instructions which, if not followed,

could endanger the personal safety and/or property of yourself and others. Read and follow

all instructions in this manual before attempting to operate the equipment. Failure to

comply with these instructions may result in personal injury. When you see this symbol.

HEED ITS WARNING!

DANGER! This machine was built to be operated according to the safe operation practices

in this manual. As with any type of power equipment, carelessness or error on the part of the

operator can result in serious injury. This machine is capable of amputating fingers, hands,

toes and feet and throwing foreign objects. Failure to observe the following safety

instructions could result in serious injury or death.

CALIFORNIA PROPOSITION 65

WARNING! Engine Exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to State of California to cause cancer and birth defects

or other reproductive harm.

Training

1. Read, understand and follow all instructions on the engine

and in the manual(s) before attempting to assemble and

operate. Keep this manual in a safe place for future and

regular reference and for ordering replacement parts.

2. Be familiar with all controls and their proper operation.

Know how to stop the engine and disengage them quickly.

3. Never allow children under 14 years of age to operate the

engine. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and be trained and supervised by an adult.

4. Never allow adults to operate the machine without proper

instruction.

5. Keep the area of operation clear of all persons, particularly

small children and pets. Stop machine if anyone enters the

area.

Preparation

1. Thoroughly inspect the area where the equipment is to

be used. Remove all stones, sticks, wire and other foreign

objects which could be tripped over and cause personal

injury.

2. Wear sturdy, rough-soled work shoes and close fitting

slacks and shirts. Loose fitting clothes or jewelry can be

caught in the moving parts. Never operate the machine in

bare feet or sandals.

3. Disengage clutch levers and shift (if equipped) into neutral

(“N”) before starting the engine.

4. Never leave the engine running while unattended.

5. Never attempt to make any adjustments while the engine

is running, except where specifically recommended in the

operator’s manual.

Safe Handling of Gasoline:

To avoid personal injury or property damage, use extreme care

in handling gasoline. Gasoline is extremely flammable and the

vapors are explosive. Serious personal injury can occur when

gasoline is spilled on yourself and/or your clothes which can

ignite. Wash your skin and change clothes immediately.

1. When adding fuel, turn engine OFF and let engine cool at

least 2 minutes before removing the gas cap.

2. Fill fuel tank outdoors or in well ventilated area.

3. Use only an approved gasoline container.

4. Never fill containers inside a vehicle or on a truck or trailer

bed with a plastic liner. Always place containers on the

ground away from your vehicle before filling.

5. If possible, remove gas-powered equipment from the truck

or trailer and refuel it on the ground. If this is not possible,

then refuel such equipment on a trailer with a portable

container, rather than from a gasoline dispenser nozzle.

6. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

4 Section 2 — important Safe operation practiceS

7. Do not overfill fuel tank. Fill tank to full as indicated by the

fuel level indicator installed inside of the fuel tank. Do not

over-fill to allow space for fuel expansion. On some models,

a fuel level indicator may NOT be present, in this instance,

fill the tank no more than 1/2 inch below the bottom of the

filler neck to allow space for fuel expansion.

8. Replace fuel cap and tighten until the cap ratchets.

9. If gasoline is spilled, wipe it off the engine and the

equipment. Move the machine to another area. Wait five

minutes before starting the engine.

10. To reduce fire hazards, keep the machine free of grass ,

leaves or other debris build up. Clean up oil or fuel spillage

and remove any fuel-soaked debris.

11. Keep gasoline away from sparks, open flames, pilot lights,

heat, and other ignition sources.

12. Never fuel equipment indoors because flammable vapors

will accumulate in the area.

13. Extinguish all cigarettes, cigars, pipes, and other sources of

ignition.

14. Check fuel line, tank, cap, and fittings frequently for cracks

or leaks. Replace if necessary.

Operation

1. When starting the engine, make sure spark plug, muffler,

and fuel cap are in place.

2. Do not crank engine with spark plug removed.

3. If fuel spills, wait until it evaporates before starting engine.

4. Allow muffler, engine cylinder, and fins to cool before

touching.

5. Keep children away from hot or running engines. They can

suffer burns from a hot muffler.

6. Remove accumulated combustibles from muffler and

cylinder area.

7. Operate equipment with all guards in place.

8. Keep hands and feet away from rotating parts.

9. Tie up long hair and remove jewelry.

10. Do not wear loose-fitting clothing, dangling drawstrings or

items that could become caught.

11. When starting the engine, pull cord slowly until resistance

is felt, then pull rapidly (if not electric start).

12. Remove all external equipment/engine loads before

starting engine.

13. Direct coupled equipment components such as, but not

limited to blades, impellers, pulleys, sprockets, etc., must

be securely attached.

Maintenance & Storage

1. Keep the engine in safe working order

2. Allow the engine to cool at least five minutes before

storing. Never tamper with safety devices. Check their

proper operation regularly.

3. Check bolts and screws for proper tightness at frequent

intervals to keep the engine in safe working condition.

Visually inspect the engine for any damage.

4. Before cleaning, repairing or inspecting; stop the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire and ground it against the

engine to prevent unintended starting.

5. Do not change the engine governor settings or over-speed

the engine. The governor controls the maximum safe

operating speed of the engine.

6. Maintain and replace safety and instruction labels as

necessary.

7. Always refer to the operator’s manual for important details

if the machine is to be stored for an extended period of

time.

8. If the fuel tank has to be drained, do this outdoors.

9. Observe proper disposal laws and regulations for gas, oil,

etc. to protect the environment.

Do not modify engine

To avoid serious injury or death, do not modify engine in any

way. Tampering with the governor setting can lead to a runaway

engine and cause it to operate at unsafe speeds. Never tamper

with factory setting of engine governor.

Notice Regarding Emissions

Engines which are certified to comply with California and federal

EPA emission regulations for SORE (Small Off Road Equipment)

are certified to operate on regular unleaded gasoline, and

may include the following emission control systems: Engine

Modification (EM), Oxidizing Catalyst (OC), Secondary Air

Injection (SAI) and Three Way Catalyst (TWC) if so equipped.

Spark Arrestor

WARNING! This machine is equipped with an

internal combustion engine and should not be used

on or near any unimproved forest-covered, brush

covered or grass-covered land unless the engine’s

exhaust system is equipped with a spark arrestor

meeting applicable local or state laws (if any).

If a spark arrestor is used, it should be maintained in effective

working order by the operator. In the State of California the

above is required by law (Section 4442 of the California Public

Resources Code). Other states may have similar laws. Federal laws

apply on federal lands.

A spark arrestor for the muffler is available through your

nearest engine authorized service dealer or contact the service

department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

5Section 2 — important Safe operation practiceS

WARNING! Your Responsibility — Restrict the use of this power machine to persons who read, understand and

follow the warnings and instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

Safety Symbols

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the

machine before attempting to assemble and operate.

Symbol Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before attempting to

assemble and operate

WARNING—GASOLINE IS FLAMMABLE

Allow the engine to cool at least two minutes before refueling.

WARNING— CARBON MONOXIDE

Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon

monoxide, an odorless and deadly gas.

WARNING— ELECTRICAL SHOCK

Do not use the engine’s electric starter in the rain

WARNING— HOT SURFACE

Engine parts, especially the muffler, become extremely hot during operation. Allow engine

and muffler to cool before touching.

Oil & Fuel Specifications

IMPORTANT: The engine is shipped without gasoline in the

engine. See the following instructions for adding gasoline.

IMPORTANT: Some engines are shipped with oil already in

the engine, others without oil already in the engine. It is very

important to check the oil level before operating the engine and

to add oil if necessary. Running the engine with insufficient oil

can cause serious engine damage and void the engine warranty.

Oil Recommendations

Before starting engine, fill with motor oil, capacity is 1100 ml/37.2

oz. Refer to viscosity chart in Figure 3-1 for oil recommendations.

Do not over-fill. Use a 4-stroke, or an equivalent high detergent,

premium quality motor oil certified to meet or exceed

U.S. automobile manufacturer’s requirements for service

classification of a minimum level SJ (higher letter ratings are

acceptable such as SL and SM grades). Motor oil will display this

designation on the container.

NOTE: Do not use non-detergent oil or 2-stroke engine oil. It

could shorten the engine’s service life.

Figure 3-1

Checking Oil Level

Some engines will have a quarter-turn oil fill/dipstick cap, others

may have a threaded oil fill/dipstick cap. Follow the instructions

next that apply to your engine model.

Checking Oil Level on Engines with Quarter-Turn Oil Fill Caps

NOTE: Be sure to check the oil while on a level surface with the

engine stopped.

To avoid engine damage, it is important to:

• Check oil level before each use and every 5 operating

hours when engine is warm. Check oil level more

frequently during engine break-in.

• Keep oil level between “H” and “L” marks on dipstick.

See Figure 3-2.

• Be sure oil fill cap/plug is tightened securely when

checking.

1. Remove the oil filler cap/dipstick and wipe the dipstick

clean. See Figure 3-2.

2. Insert the cap/dipstick into the oil filler neck, and tighten

the cap until seated.

3. Remove the oil filler cap/dipstick. If the level is low, slowly

add oil until oil level registers between high (H) and low (L),

Figure 3-2.

4. Replace and tighten cap/dipstick firmly before starting

engine.

NOTE: Do not overfill. Overfilling with oil may cause smoking,

hard starting, or spark plug fouling.

NOTE: DO NOT allow oil level to fall below the “L” mark on the

dipstick. Doing so may result in equipment malfunctions or

damage.

NOTE: To change the oil on your engine, see the Maintenance

Section of this manual.

Fill

between

high

and low

marks

Figure 3-2

Set-Up

Filling Oil Sump

1. Be sure the engine is upright and level.

2. Remove the oil fill cap dipstick from oil filler tube by

rotating counter-clockwise and lifting the dipstick out of

the engine. Wipe the dipstick clean with a shop rag.

3. Insert oil fill cap dipstick back into oil filler tube. On

quarter-turn oil fill caps, tighten by rotating the cap

clockwise until firmly seated.

NOTE: Some units may have a threaded dipstick. In this

instance, insert the cap/dipstick into the oil filler neck, but

do not screw it in to check.

4. Loosen and remove the oil fill cap dipstick from the oil

filler tube. Note the oil level, if oil reading on the dipstick is

below the “L” mark, slowly add oil to reach the “FULL” level.

See Figure 3-2 or Figure 3-3, whichever is applicable.

5. Insert oil fill cap dipstick back into oil filler tube. Tighten by

rotating the cap clockwise until firmly seated.

6. Wipe away any spilled oil.

NOTE: To change the oil, see Checking and Changing Oil

instructions in the Maintenance Section of this manual.

Checking Oil Level on Engines with Threaded Oil Fill Caps

NOTE: Be sure to check the oil while on a level surface with the

engine stopped.

To avoid engine damage, it is important to:

• Check oil level before each use and every 5 operating

hours when engine is warm. Check oil level more

frequently during engine break-in.

• Keep oil level between “H” and “L” marks on dipstick.

See Figure 3-3.

• Be sure to rest oil fill cap on the threads when

checking. Do not tighten down oil fill cap when

checking the oil on threaded oil fill cap engines.

1. Remove the oil filler cap/dipstick and wipe the dipstick

clean. See Figure 3-3.

2. Insert the cap/dipstick into the oil filler neck, but do not

screw it in.

3. Remove the oil filler cap/dipstick. If the level is low, slowly

add oil until oil level registers between high (H) and low (L),

Figure 3-3.

4. Replace and tighten cap/dipstick firmly before starting

engine.

NOTE: Do not overfill. Overfilling with oil may cause smoking,

hard starting, or spark plug fouling.

NOTE: DO NOT allow oil level to fall below the “L” mark on the

dipstick. Doing so may result in equipment malfunctions or

damage.

NOTE: To change the oil on your engine, see the Maintenance

Section of this manual.

Fill

between

high

and low

marks

Figure 3-3

7Section 2 — Set-Up

Fuel Recommendations

CAUTION: Operating the engine with E15 or E85

fuel, an oil/gasoline mixture, dirty gasoline, or

gasoline over 30 days old that has not been

stabilized using a fuel additive, may result in

damage to your engine’s carburetor. Subsequent

damage would not be covered under the

manufacturer’s warranty.

Use automotive gasoline (unleaded or low leaded to minimize

combustion chamber deposits) with a minimum of 87 octane.

Gasoline with up to 10% ethanol or 15% MTBE (Methyl Tertiary

Butyl Ether) can be used. Never use an oil/gasoline mixture or

dirty gasoline. Avoid getting dirt, dust, or water in the fuel tank.

DO NOT use E15 or E85 gasoline.

WARNING! Gasoline is extremely flammable and is

explosive under certain conditions.

• Refuel in a well-ventilated area with the engine stopped.

Do not smoke or allow flames or sparks in the area where

the engine is refueled or where gasoline is stored.

• Do not overfill the fuel tank. After refueling, make sure the

tank cap is closed properly and securely.

• Be careful not to spill fuel when refueling. Spilled fuel or

fuel vapor may ignite. If any fuel is spilled, make sure the

area is dry before starting the engine.

• Avoid repeated or prolonged contact with skin or

breathing of vapor.

Adding Fuel

WARNING! An adult should fuel this engine. NEVER

allow children to refuel this engine. Gasoline (fuel)

vapors are highly flammable and can explode. Fuel

vapors can spread and be ignited by a spark or flame

many feet away from engine. To prevent injury or

death from fuel fires, follow these instructions:

• DO NOT use leaded fuel.

• Fuel must be fresh and clean. NEVER use fuel left over

from last season or stored for long periods.

• NEVER mix oil with fuel.

• DO NOT use fuel containing Methanol (Wood

Alcohol)

1. Before refueling, allow the engine to cool for two minutes.

2. Be sure engine is outdoors and in a well-ventilated area.

3. Clean area around the fuel fill cap and remove the fuel fill cap.

4. Using an approved red GASOLINE container, add fuel

slowly, being careful to avoid spilling.

NOTE: On tanks with a fuel level indicator, fill the tank until

the fuel reaches the “fuel full” indicator mark. See Figure

3-4. All other tanks, fill tank until the fuel reaches a ⁄ inch

below the bottom of the filler neck to allow space for fuel

expansion. Be careful not to overfill.

5. Replace the fuel cap and tighten securely. Wipe up spilled

fuel before starting engine. If fuel is spilled DO NOT start

engine. Move machine away from area of spillage. Avoid

creating any source of ignition until fuel vapors are gone.

6. Be sure fuel valve, if present, is open.

Fuel Level Indicator

Top View

Figure 3-4

Electrical Power

WARNING! DO NOT pull starter rope with engine

running. Doing so may VOID YOUR WARRANTY.

CAUTION: The extension cord can be any length,

but must be rated for 15 amps at 125 volts, grounded

and rated for outdoor use.

NOTES: When connecting power cord always

connect power cord to switch box on engine first;

then into outlet. See Figure 3-5

Determine what type of power source outlet you will be

connecting the power cord to, before you start your engine.

See Engines with Electric Starters instructions in the Operation

Section of this manual.

Figure 3-5

8 Section 2— Set-Up

Controls and Features

Throttle

The throttle control is located on the rear of the engine. It

regulates the speed of the engine and will shut off the engine

when moved into the STOP position.

Choke

Activating the choke closes the choke plate on the carburetor

and aids in starting the engine.

Fuel Shut-Off Control

If equipped, is used for controlling the flow of fuel between

usage and transport/storage.

Primer Bulb

Pressing the primer bulb forces fuel directly into the engine’s

carburetor to aid in starting a “Cold” engine.

Oil Drain

Removing the oil drain plug will drain the oil from the engine.

Oil Filler Cap & Dipstick

Remove the oil cap to check the oil level and add oil.

Fuel Fill

Remove the cap to add fuel.

Electric Starter Inlet

Requires the use of a three-prong outdoor extension cord and a

120V power source/wall outlet.

Recoil Starter Handle

This handle is used to manually start the engine.

Electric Start Button

Pressing the button on the top of the electric starter switch

engages the engine’s electric starter when plugged into a 120V

power source.

Key

The key is a safety device. It must be fully inserted in order for the

engine to start. Remove the key when the snow thrower is not in

use.

Important: Do not turn the key in an attempt to start the

engine. Doing so may cause it to break.

Starter Handle

Primer

Bulb

Muffler

Oil Drain

Air Filter Cover

Electric Inlet &

Starter Button

Air Filter

Thumb Screws

Oil Drain

Fuel Fill

Oil Fill/Dipstick

Fuel Shut-Off

Control

Choke

Key

Throttle

Figure 4-1

Operation

Pre-Operation Check

IMPORTANT: The engine is shipped without gasoline or oil in

the engine. See the Set-Up Section of this manual for instructions

on adding oil and gasoline.

For your safety, and in order to maximize the service life of this

equipment, it is very important to check its condition before you

operate this engine. Make certain to service, correct or fix any

problem that might be identified before attempting to operate

this engine.

WARNING! Improperly maintaining this engine, or

failure to correct any problem before operation can

cause a malfunction which could result in serious

injury or even death.

Always perform a pre-operation inspection before

each operation, and correct any problem.

Before you start the engine, always check the following items:

1. Fuel Recommendations (See Set Up Section)

2. Checking Oil Level (See Set Up Section)

3. Air filter (if equipped) (See Maintenance Section)

4. General Overall Inspection. Check for any fluid leaks or

discharges, and loose or damaged parts.

5. Check the owner’s manual provided with the equipment

that is powered by this engine. Review the owner’s manual

for any precautions and procedures that should be

followed before starting the engine.

Starting the Engine

WARNING! Always keep hands and feet clear of

moving parts. Do not use a pressurized starting

fluid. Vapors are flammable.

WARNING! An adult should start the engine. Only

allow children to start the engine if an adult has

determined they are experienced and capable of

such operation.

WARNING! If you are unable to start this engine

after following instructions in this manual, contact

you authorized MTD Service Dealer. To avoid serious

burn injuries or damage to your engine, DO NOT

attempt to start or troubleshoot this engine in any

other way. for example:

• DO NOT use starting fluid.

• DO NOT spray flammable vapors into the

carburetor.

• DO NOT put flammable liquids into carburetor.

• DO NOT operate engine or pull on starter rope

with spark plug removed. Fuel can spray from

spark plug hole and ignite.

NOTE: Allow the engine to warm up for a few minutes after

starting. The engine will not develop full power until it reaches

operating temperatures.

Familiarize yourself with the engine symbols shown in Figure 5-1

before attempting to start this engine. If this engine is remotely

controlled by the equipment it is powering, be sure to familiarize

yourself with the equipment Operator’s Manual as well.

ChokeRun

Fast Slow/Idle Engine Off

Primer

Figure 5-1

NOTE: The following starting instructions are for several different

types of engines. In order to locate the instructions that apply to

your engine, first determine what type of starter you have. If you

have an electric starter, see Engines With Electric Starters. If you

have a manual recoil starter, see Engines with Recoil Starters later

in this section.

Engines With Electric Starters

If you have a manual recoil starter, see Engines with Recoil

Starters later in this section.

WARNING! DO NOT pull the starter handle while

the engine is running.

WARNING! The electric starter is equipped with

a 120V A.C. Power Plug designed to operated

with a grounded extension cord and on 120V A.C.

household current. It must be properly grounded

at all times to avoid the possibility of injury or death

from electrical shock.

a. Determine if your house wiring has a Ground Fault

Interrupted (G.F.I.) Three-Wire Grounded System; if

you are not sure, ask a Licensed Electrician.

b. If your house wiring does not have a G.F.I. Three-

Wire Grounded System, DO NOT USE THIS ELECTRIC

STARTER UNDER ANY CONDITION.

11Section 5 — operation

c. If your house wiring is grounded and a G.F.I.

three-Prong Wall Receptacle is not available at the

location where your starter will be used, one must

be installed by a Licensed Electrician BEFORE USING

THE ELECTRIC STARTER!

1. To avoid carbon monoxide poisoning, be sure engine is

outdoors in a well-ventilated area.

2. Be sure fuel valve, if present (see equipment Operator’s

Manual instructions) is open and all switches are on.

NOTE: If your engine is equipped with a 12V battery-

operated electric starter, proceed Step 5.

3. Plug an extension cord into the outlet located on the

engine’s surface. Plug the other end of extension cord

into a three-prong 120-volt, grounded, AC outlet in a well-

ventilated area.

CAUTION: The extension cord can be any length,

but must be rated for 15 amps at 125 volts, grounded

and rated for outdoor use.

IMPORTANT: When connecting the power cord, always

connect the power cord to the switch box on the engine first;

then into the outlet.

4. Move engine speed control, if equipped, in the “Fast”

position.

5. If equipped, set the choke control to “FULL CHOKE”

position.

6. Hold the primer bulb in for one full second each time you

press it.

• Make sure you cover the vent hole with your

thumb.

• Prime between 3 and 5 times.

IMPORTANT: DO NOT operate an electric starter for more than

5 seconds during each attempt.

NOTE: DO NOT use the primer bulb to restart a warm

engine after a short shutdown. Doing so will flood the

engine and may result in equipment malfunction.

NOTE: If restarting a warm engine after a short shutdown,

move the engine speed control (if equipped) the “FAST”

position and move the choke control to the “NO CHOKE”

position.

7. Push the starter button to start the engine.

NOTE: If the engine fails to start after 3 attempts, repeat

steps 1 through 8.

8. When the engine starts:

• Release the starter button.

• Move the choke control to 1/2 “CHOKE” position

until the engine runs smoothly.

• Next, move the choke control to the NO CHOKE

position.

9. Move the engine speed control (if equipped) to the desired

speed in the “RUN” range.

NOTE: If the engine starts but falters when the choke

control is moved to the “NO CHOKE” position:

• Momentarily move choke control back to “FULL

CHOKE” position.

• Next, move the choke control to “1/2 CHOKE”

position until engine runs smoothly.

• Finally, move the choke control to the NO

CHOKE position.

If the engine dies after choke control is moved to “NO CHOKE”

position, repeat steps 5 through 10 to restart engine.

10. If the engine fails to start after 3 attempts in the “NO

CHOKE” position, move the choke control to “FULL CHOKE”

position and start engine.

NOTE: When disconnecting the power cord, always

disconnect the power cord from the outlet first; then

disconnect the power cord from the switch box on the

engine.

11. Disconnect the power cord form the outlet.

12. Disconnect the power cord form the switch box on the

engine.

13. If engine does not start after following steps 1 through

12, contact your Authorized MTD Service Dealer. DO NOT

attempt to troubleshoot this engine in any other way.

Engines with Recoil Starters

If you have an electric starter, see Engines with Electric Starters

earlier in this section.

WARNING! DO NOT pull starter rope with engine

running. Doing so may VOID YOUR WARRANTY.

1. To avoid carbon monoxide poisoning, be sure engine is

outdoors in a well-ventilated area.

2. Be sure fuel valve, if present (see equipment Operator’s

Manual instructions) is open and all switches are on.

3. Move the engine speed control, if equipped, to the “FAST”

position.

4. If equipped, set the choke control to “FULL CHOKE”

position.

5. Hold the primer bulb in for one full second each time you

press it.

• Make sure you cover the vent hole with your

thumb.

• Prime between 3 and 5 times.

NOTE: DO NOT use the primer bulb to restart a warm

engine after a short shutdown. Doing so will flood the

engine and may result in equipment malfunction.

NOTE: If restarting a warm engine after a short shutdown,

move the engine speed control (if equipped) the “FAST”

position and move the choke control to the “NO CHOKE”

position.

6. Operate equipment control to release engine brake or

clutch, if equipped (see equipment Operator’s Manual).

WARNING! When pulling the starter rope, the

rope can unexpectedly jerk back toward the engine

causing serious injury. To avoid this risk, carefully

12 Section 5— operation

follow these instructions:

7. Grasp the starter cord handle.

• Pull rope out slowly until you feel drag.

• Without allowing the rope to retract, continue

pulling the rope with one rapid full arm stroke.

• Return the rope slowly to the original position.

NOTE: Following the instructions listed in the steps above avoids

potential damage to the recoil mechanism.

If the recoil starter handle is frozen and will not operate the

engine, proceed as follows:

• Pull as much rope out of the starter as possible.

• Release the starer handle and let it snap back

against the starter to break up ice’; these two

steps should only be done when the starter is

frozen.

8. If the engine fails to start after 3 attempts repeat steps 1

through 7 and try again.

9. When the engine starts:

• Move the choke control to 1/2 “CHOKE” position

until the engine runs smoothly.

• Next, move the choke control to the NO CHOKE

position.

10. Move the engine speed control (if equipped) to the desired

speed in the “RUN” range.

NOTE: If the engine starts but falters when the choke

control is moved to the “NO CHOKE” position:

• Momentarily move choke control back to “FULL

CHOKE” position.

• Next, move the choke control to “!/2 CHOKE”

position until engine runs smoothly.

• Finally, move the choke control to the NO

CHOKE position.

If the engine dies after choke control is moved to “NO CHOKE”

position, repeat steps 3 through 10 to restart engine.

11. If the engine fails to start after 3 attempts in the “NO

CHOKE” position, move the choke control to “FULL CHOKE”

position and start engine.

12. If engine does not start after following steps 1 through

11, contact your Authorized MTD Service Dealer. DO NOT

attempt to troubleshoot this engine in any other way.

Stopping the Engine & Short Term Storage

Stop engine in accordance with the equipment Operator’s

Manual.

WARNING! To avoid unsupervised engine

operation, especially by children, NEVER leave the

engine unattended while running. Always turn off

the engine after use and remove the ignition key, if

equipped.

WARNING! NEVER store the engine with fuel in the

fuel tank inside a building with potential sources of

ignition such as hot water tank and space heaters,

clothes drivers, electric motors, etc.

Stopping The Engine

1. If operating the engine in the snow or rain, run the engine

for a few minutes to help dry off any moisture.

2. Move the equipment control, if present (see Equipment

Owner’s Manual), engine control lever or ignition switch to

“STOP” or “OFF” position.

3. Remove ignition key, if provided (see equipment Operator’s

Manual).

NOTE: Removing the key will reduce the possibility of

unauthorized starting of the engine while equipment is not

in use.

WARNING! NEVER store the engine with fuel in the

fuel tank inside a building with potential sources of

ignition such as hot water tank and space heaters,

clothes dryers, electric motors, etc.

After the Engine is Stopped

WARNING! To prevent the possible freeze-up of

engine controls, follow instructions with engine

STOPPED, listed below:

1. Wipe all snow and moisture from the engine control lever

and choke areas.

2. Move the equipment control, if present, (see equipment

Operator’s Manual), engine control lever or ignition switch

back and forth several times and leave the control in the

“STOP” or “OFF” position.

3. Move the engine choke back and forth several times and

leave in the “FULL CHOKE” position.

4. Be sure the Fuel Shut-Off Valve, , if present, is off.

Maintenance

Periodic inspection and adjustment of the engine is essential if

high level performance is to be maintained. Regular maintenance

will also ensure a long service life. The required service intervals

and the kind of maintenance to be performed are described

in the table above. Follow the hourly or calendar intervals,

whichever occur first. More frequent service is required when

operating in adverse conditions.

WARNING! Shut off the engine before performing

any maintenance. To prevent accidental start-up,

disconnect the spark plug boot.

NOTE: If engine must be tipped to transport equipment or to

inspect or remove grass, keep spark plug side of engine up.

Transporting or tipping engine spark plug down may cause

smoking, hard starting, spark plug fouling, or oil saturation of air

cleaner.

WARNING! If the engine has been running, the

muffler will be very hot. Be careful not to touch the

muffler.

Oil Recommendations

Refer to viscosity chart in Figure 6-1 for oil recommendations.

Do not over-fill. Use a 4-stroke, or an equivalent high detergent,

premium quality motor oil certified to meet or exceed

U.S. automobile manufacturer’s requirements for service

classification of a minimum level SF or SG (higher letter ratings

are acceptable such as SJ, SL and SM grades). Motor oil will

display this designation on the container.

NOTE: Do not use non-detergent oil or 2-stroke engine oil. It

could shorten the engine’s service life.

Figure 6-1

Maintenance Schedule

First 5 Hours

Each Use or

Every 5 Hrs.

Every Season

or 25 Hours

Every Season

or 50 Hours

Every Season

or 100 Hours

Service Dates

Check Engine Oil Level

Change Engine Oil

P P

Check Air Cleaner (If so equipped)

Service Air Cleaner (If so equipped)

Check Spark Plug

Replace Spark Plug

Clean Engine Shroud (If so equipped)

Clean around muer

Replace Fuel Filter (If equipped)

14 Section 6— Maintenance

Checking and Changing the Oil

To avoid engine damage, it is important to:

• Check oil level before each use and every 5 operating hours

when the engine is warm.

• Change the oil after the first 5 operating hours and every

50 operating hours thereafter. Engine should still be warm

but NOT hot from recent use.

Oil Fill Cap and Dipstick

WARNING! Before tipping engine or equipment to

drain oil, drain fuel from tank by running engine

until fuel tank is empty.

1. Carefully disconnect the spark plug wire and keep it away

from the spark plug. Refer to Figure 6-2 for spark plug

location.

• Keep the disconnected spark plug wire securely

away from the metal parts where arcing could

occur.

• Carefully attach the spark plug wire to the

grounding post, if provided.

Spark Plug

Boot

Figure 6-2

2. Be sure that the fuel fill cap is on and securely tightened.

3. Be sure to find correct oil drain plug location, if present

(see the equipment Operator’s Manual instructions for

additional information).

4. Clean area around the oil drain plug.

5. Place an approved recyclable oil container under the oil

drain plug.

6. Remove the Oil drain plug. See Figure 6-3.

WARNING! Used motor oil may cause skin cancer if

repeatedly left in contact with the skin for prolonged

periods. Although this is unlikely unless you handle

used oil on a daily basis, it is still advisable to

thoroughly wash your hands with soap and water as

soon as possible after handling used oil.

Oil

Drain

Figure 6-3

7. Tip engine to position the oil flow, so it will drain from the

lowest point on the engine.

8. Drain the oil into an approved recyclable oil container.

NOTE: Please dispose of used motor oil in a manner that is

compatible with the environment. We suggest you take it in a

sealed container to your local service station for reclamation.

Do not throw it in the trash or pour it on the ground.

9. Install the oil drain plug and tighten securely.

10. Clean area around the oil drain plug.

11. Remove the oil fill cap dipstick.

12. Fill with the recommended Oil. See Figure 6-1.

NOTE: DO NOT overfill oil filler. Doing so may result in oil

carry-over to the equipment and cause malfunction or

damage.

NOTE: DO NOT allow oil level to fall below and “L” mark on

dipstick. Doing so may result in equipment malfunction or

damage.

13. Wipe away any spilled oil.

14. Check the oil level by installing the Oil Fill Cap/Dipstick.

• For threaded Oil Fill Cap/Dipstick models, rest

the cap on the threads, do not tighten down the

cap to check the oil level.

• For quarter-turn Oil Fill Cap/Dipstick models,

tighten down the cap to check the oil level.

NOTE: See the Set-Up section earlier in this manual for

detailed instructions on identifying and checking the oil on

each of these specific engine models.

15. Remove the oil filler cap/dipstick. If the level is low, slowly

add oil until oil level registers between high (H) and low (L),

Fig. 3-2 and 3-3 in the Set-Up section.

16. Repeat Steps 14 & 15 to be sure that the correct oil level has

been achieved.

17. Once the proper oil level has been confirmed, install the Oil

Fill Cap/Dipstick. Tighten securely.

15Section 6 — Maintenance

18. Carefully disconnect spark plug wire from grounding post,

if present.

19. Carefully reconnect the spark plug wire to the spark plug.

NOTE: It is advisable to recheck the oil level after you have

operated the engine for a short while, and the normal engine

operating temperature has been achieved.

WARNING! If the engine has been running, the

muffler, engine head and spark plug will be very hot.

Be careful not to touch any of these components

until they have cooled.

Spark Plug Service

WARNING! DO NOT check for spark with spark

plug removed. DO NOT crank engine with spark

plug removed.

Check the spark plug yearly or every 100 operating hours. To

ensure proper engine operation, the spark plug must be properly

gapped and free of deposits.

1. Remove the spark plug boot.

2. Clean the area around the spark plug.

3. Use a spark plug wrench to remove the plug.

WARNING! If the engine has been running, the

muffler, engine head and spark plug will be very hot.

Be careful not to touch any of these components

until they have cooled.

4. Visually inspect the spark plug. Discard the spark plug

if there is apparent wear, or if the insulator is cracked or

chipped. Replace the plug if the electrodes are pitted,

burned or fouled with deposits.

5. Clean the spark plug with a wire brush if it is to be reused.

6. Measure the plug gap with a feeler gauge. Correct as

necessary by bending side electrode. See Figure 6-4. The

gap should be set to 0.030 in. (0.76mm).

7. Check that the spark plug washer is in good condition

8. Thread the spark plug in by hand to prevent cross-

threading.

0.06-0.03 in.

0.60-0.80 mm

Electrode

Figure 6-4

9. After the spark plug is seated, tighten with a spark plug

wrench to compress the washer.

NOTE: When installing a new spark plug, tighten ⁄ turn

after the spark plug seats to compress the washer. When

reinstalling a used spark plug, tighten ⁄-⁄ turn after the

spark plug seats to compress the washer.

NOTE: The spark plug must be securely tightened. An

improperly tightened spark plug can become very hot and

may damage the engine.

Air Filter

NOTE: Not all engines have air filters, such as engines used for

snow throwers. Service the air filter if one is present.

Paper filters cannot be cleaned and must be replaced once a

year or every 10 operating hours; more often if used in extremely

dusty conditions.

WARNING! Never use gasoline or low flash point

solvents for cleaning the air cleaner element. A fire

or explosion could result.

NOTE: Never run the engines that have air filters without them.

Rapid engine wear can result.

1. Press the tab on the air filter cover and lift the cover, or

un-thread the thumbscrews, depending on the model of

engine you have. See Figure 6-5.

Figure 6-5

2. Replace paper element when dirty or damaged. Clean

foam element or replace when damaged.

3. To clean foam element, separate it from the paper element

and wash in liquid detergent and water. Allow to dry

thoroughly before using. Do not oil the foam element.

Adjustments

DO NOT make any engine adjustments. Factory settings are

satisfactory for most conditions. If adjustments are needed,

contact your Authorized MTD Servicing Dealer.

16 Section 6— Maintenance

Carburetor

If you think you carburetor needs adjusting, see your nearest

Authorized MTD Servicing Dealer. Engine performance should

NOT be affected at altitudes up to 7,000 feet (2,134 meters). For

operation at higher elevations, contact your Authorized MTD

Servicing Dealer

Alternator (if equipped)

Contact your Authorized MTD Servicing Dealer for alternator

Troy-Bilt 24BL59M5711 User manual

Brand: Troy-Bilt

Model: 24BL59M5711

Type: User manual

Download PDF

report

in other languages

español: Troy-Bilt 24BL59M5711 Manual de usuario

Troy-Bilt 24BL59M5711 User manual

Troy-Bilt 24BL59M5711 User manual

in other languages

Related papers

Other documents