Rust-Oleum Automotive 304611 User manual

Brand: Rust-Oleum Automotive

Model: 304611

Type: User manual

TECHNICAL DATA PCG-06

PEEL COAT

™

PEELABLE PRIMER

Form: GDH-1222

Rev.: 053017

.DESCRIPTION AND USES .

Rust-Oleum

Peel Coat

Peelable Primer with Peel Coat

technology makes any Rust-Oleum spray paint a peelable

coating. Peelable Primer creates an endless selection of unique

colors and finishes to temporarily customize your vehicle. Spray

Peelable Primer on a clean surface then top coat it with any

Rust-Oleum spray paint from high gloss colors to pearl metallics

to hammered finishes and more. The coating is gasoline

resistant, simple to remove and safe to wash. It is also easy to

apply on OEM painted surfaces, metal, plastic, glass and more.

Peelable Primer has been formulated for temporary use and is

recommended to be removed within 6 months

.FEATURES .

•

Easily removable

•

Quick and easy application

•

Excellent coverage and adhesion

.PRODUCTS .

SKU Description

304611 White

..PRODUCT APPLICATION .

PAINTING CONDITIONS

Use outdoors or in a well ventilated area. Use when

temperature is between 50-90°F (10-32°C) and humidity is

below 65% to ensure proper drying. Do not apply to

galvanized metals or to surfaces that exceed 300°F

(148°C). Avoid spraying in very windy, dusty conditions.

Cover surrounding area to protect from spray mist. If

applying outside, ensure no rain is forecast for at least 24

hours.

SURFACE PREPARATION

Thoroughly wash the surface with soap and water prior to

the application. Make sure no oil, wax or grease remains

on the surface. Mask off around areas you do not wish to

paint. Make sure the surface is completely dry before

spraying.

..PRODUCT APPLICATION (cont.) .

APPLICATION

It is recommended to test in any inconspicuous area prior

to full application.

Shake can vigorously for one minute after mixing ball

begins to rattle. If mixing ball fails to rattle, DO NOT

STRIKE. Contact Rust-Oleum. Shake can often during use.

Apply 3 or more coats, waiting 2-5 minutes between coats.

A coat is defined as covering the entire area once. Hold

the can 8-12” from the surface and spray in a steady back

and forth motion, slightly overlapping each stroke until the

entire area is covered. If peelable Primer has dried for

more than 20 minutes between coats, allow it to fully dry,

peel off and start over.

DRY & RECOAT

Dry and recoat times are based on 70°F (21°C) and 50%

relative humidity. Allow more time at cooler temperatures.

Allow Peelable Primer to dry for 4 hours before applying a

topcoat of a Rust-Oleum branded spray paint.

UN-MASKING

Immediately after applying the final coat of Peelable

Primer, begin removing tape and masking to ensure clean

edges.

TOP COATING

Once the Peelable Primer coating has dried for at least 4

hours, you can top coat with any Rust-Oleum spray paint.

Thoroughly mask off the areas you do not want to paint.

Follow label directions when using Rust-Oleum spray paint

and refer to each label for appropriate dry times and

instructions. Note: Do not use with water-based spray

paints.

CLOGGING

VERY IMPORTANT! Clear spray valve by turning can

upside down and pushing the spray button for 5 seconds.

CLEAN-UP

For any overspray, allow Peelable Primer to dry. Once dry;

peel away. Throw empty cans in trash pickup. Do not burn

or place in home compactor.

REMOVAL

When you are ready to peel off and start your next design,

peel off starting at an edge and work it back with your

finger tip. Once removed, the top coat will be removed

with the original Peelable Primer coat. To ensure easy

removal, peel off within 6 months of application. A

microfiber cloth can assist in the removal of film in intricate

areas.

TECHNICAL DATA

PEEL COAT

™

PEELABLE PRIMER

Rust-Oleum Corporation Form: GDH-1222

11 Hawthorn Parkway Phone: 877•385•8155 Rev.: 053017

Vernon Hills, Illinois 60061 www.rustoleum.com

An RPM Company

PHYSICAL PROPERTIES .

PEELABLE PRIMER

Resin Type

Polyurethane

Pigment Type

Titanium Dioxide

Solvents

Water, Glycol Ethers

MIR

1.60 Max

Fill Weight

12 ounces

Recommended Dry Film

Thickness (DFT) Per Coat

4.0 mils

(100µ)

Practical Coverage

at Recommended DFT

6-7 sq.ft./can

(0.6-0.65 m

/can)

Dry Times at 70-80°F

(21-27°C) and 50%

Relative Humidity

Touch

3-4 hours

Handle

4 hours

Full Cure

24 hours

Dry Heat Resistance

300°F (148°C)

Shelf Life

2 years

Flash Point

-42°F (-41°C)

Safety Information

For additional information, see SDS

The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature

do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we

can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All

technical information is subject to change without notice.