OWNER/OPERATOR’S
MANUAL & PARTS LIST
Revised 10/22/08
09.10047
SNOW BLOWER
KX522
ii
TO THE OWNER
Venture Products Inc. reserves the right to make changes
in design or specifications without obligation to make like
changes on previously manufactured products.
Orrville, OH
www.ventrac.com
Model # (A): _______________________
Serial # (B): ________________________
Affix Part/Serial Number label here
Product Identification
If you need to contact an Authorized Ventrac Dealer for information on servicing your product,
always provide the Product Model and Serial numbers.
Please fill in the following information for future reference. See picture below to find the loca
-
tion of the identification number. Record them in the spaces provided below.
Date of Purchase: Month _________________ Day ___________ Year ___________________
Dealer: _______________________________________________________________________
Dealer Address: ________________________________________________________________
________________________________________________________________
Dealer Phone Number: __________________________________________________________
Dealer FAX Number: ____________________________________________________________
INTRODUCTION SECTION A
Description & Specifications ..................................A-1
SAFETY SECTION B
Safety Symbols ........................................B-1
Decals .............................................B-2
General Safety Procedures ..................................B-3
Safety Operation & Techniques ................................B-4
OPERATION SECTION C
Attaching ...........................................C-1
Detaching ...........................................C-1
Operating Techniques & Tips .................................C-1
MAINTENANCE/ADJUSTMENTS SECTION D
Bearing Lubrication ......................................D-1
Gearbox Lubrication ......................................D-1
Belt Replacement .......................................D-1
Chute Adjustment .......................................D-2
Skid Shoe Adjustment .....................................D-2
Auger Housing Wear Edge Adjustment ............................D-2
PARTS & ILLUSTRATED DRAWINGS SECTION E
Main Frame & Auger Drive ................................E-1&2
Main Drive & Fan Drive ..................................E-3&4
Chute & Hydraulics ....................................E-5&6
Shields, Decals, & Cutting Edge .............................E-7&8
PARTS/OPTIONS SECTION F
12 Volt Actuator Deflector Control .............................F-1&2
Top Auger .........................................F-3&4
WARRANTY
TABLE OF CONTENTS
iii
Product Description
KX522 Snow Blower
The Ventrac Model KX522 Snow Blower is a powerful, high capacity, two-stage snow blower. It
combines an aggressive sixteen inch auger with a heavy duty, high speed fan to make a powerful and
efficient snow removing attachment for the Ventrac 4000 series tractors.
The KX522 Snow Blower features:
a hydraulic motor that rotates the discharge chute 220 degrees.
a reversible, hardened cutting edge.
a shock absorbing belt drive to protect the gearbox.
quick attach mounting to the tractor.
adjustable skid shoes
adjustable auger housing side wear edges.
For areas with heavy snowfall, an optional second auger (Kit # 70.8072) is available. This second
auger mounts above the 16" auger for effective removal of deeper snow.
An optional 12 volt actuator (Kit # 70.8025) can be added to control the chute deflector angle from the
tractor seat.The 12 volt actuator is designed for use along with one of the following switch and plug
kits, based on your tractor model.
If you have a Model 4100 or 4200 tractor, a KT 12v Switch & Plug Kit (# 70.4039) is required.
If you have a Model 4000 tractor, an HT 12v Switch & Plug Kit (# 70.4046) is required.
A-1
INTRODUCTION
Ventrac KX522 Specifications
Overall Height....................................58-1/2 inches
Overall Length ...................................43-3/4 inches
Overall Width ......................................52inches
Weight ........................................440pounds
Auger Opening Width ..................................48inches
Auger Diameter .....................................16inches
Fan Diameter ....................................19-1/2 inches
Venture Products, Inc. reserves the right to change these specifications without notice.
SAFETY
B-1
ATTENTION:
This symbol identifies potential health and
safety hazards. It marks safety precau
-
tions. Your safety and the safety of others
is involved.
SIGNAL WORD DEFINITIONS
Indicates a potentially hazardous situation
which, if not avoided, may result in minor
or moderate injury and/or property dam
-
age. It may also be used to alert against
unsafe practices.
Indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury.
Indicates an imminently hazardous situa-
tion which, if not avoided, will result in
death or serious injury. This signal word is
limited to the most extreme cases.
The following decals must be maintained on your Ventrac Attachment. If any decals
are faded or missing, contact your dealer promptly for replacements.
B-2
SAFETY
A
F
G
Decal Page & Location Description Part Number
A
E-7, #5
F-3, #29
Danger - Shield Missing 00.0062
B
E-7, #18 Hazard - Moving Part 00.0101
C
E-7, #17 Thrown Object Hazard 00.0122
D
E-5, #34 (2) Keep Hands & Feet Away 00.0123
E
E-7, #23 (2)
F-3, #27
Danger - Auger Hazard 00.0208
F
E-7, Warning - Read Owner's Manual 00.0217
G
E-7, General Safety 00.0220
B C
D
E
General Safety Procedures
for Ventrac Tractors, Attachments, & Accessories
Read and understand the operator’s manual before operating this equipment.
Observe and follow all safety decals.
DO NOT let children or any untrained person operate the tractor or attachment. Make sure that all
operators of this equipment are thoroughly trained in using it safely.
Never allow additional riders on the tractor or attachments.
DO NOT operate tractor or attachments if you are under the influence of alcohol, drugs, or medication
that may impair judgment or cause drowsiness, or if you are not feeling well.
Operate all controls from the operator’s seat only.
Before operating equipment, make sure all shields are in place and fastened.
Ensure the attachment or accessory is locked or fastened securely to the tractor before operating.
See tractor manual for locking procedure.
Ensure that all bystanders are clear of the tractor and attachment before operating. Be especially
careful and observant if other people are present. Never assume that bystanders will remain where
you last saw them.
Always look in the direction the tractor is moving.
Never direct the discharge of any attachment in the direction of people, animals, buildings, vehicles,
or objects of value.
Stop operation immediately at any sign of equipment failure and correct the problem before
continuing to operate. An unusual noise can be a warning of equipment failure or a sign that
maintenance is required.
Before adjusting, cleaning, lubricating, or changing parts on the tractor or attachment, engage the
parking brake, lower the attachment to the ground, stop the engine, and remove the ignition key.
To prevent the risk of uncontrolled equipment movement on tractors equipped with 2 speed axles,
always shift the transaxle range with the tractor stationary on level ground and with the parking brake
engaged.
If equipment is to be left unattended, engage the parking brake, lower the attachment to the ground,
stop the engine, and remove the ignition key.
B-3
SAFETY
KX522 Safety Procedures
The design and power used to move snow must be effective to break up snow and to blow it for
relocation. This could make the snow blower a lethal “weapon” when misused. Operators should be
extremely careful never to direct the snow blower or its discharge chute toward people or anything of
value. Even snow discharged from the machine can be solid enough to cause serious injury. Frozen
snow, ice, gravel, and other objects can be thrown at deadly speeds.
Operators should know the area being cleared and make preparations ahead of time. Place guide
stakes appropriately, remove stones or markers of any kind that may be covered after a snowfall.
Curbs, offsets, steps, manholes, broken pavement, etc. should be noted. Operators are encouraged
to map the area(s) to be cleared before the winter season to remind the operator of potential
hazards. If an area is to be cleared that is unfamiliar to the operator, travel slowly and use EXTREME
CAUTION. Inquire of anyone who might know of potential hazards.
The operator should never proceed if visibility is poor. If the tractor is equipped with a cab, the
windshield must be kept clean. Wait for blinding snowstorms and squalls to subside, and discharge
snow with the wind direction as much as possible. Discharging snow against the wind reduces the
blowing distance and generally reduces visibility by creating a snowstorm effect.
Use extra care when you come to shrubs, trees, or other objects that may block your vision.
Shut off the PTO when you are not blowing snow.
Always stop the snow blower and engage the parking brake before dismounting to change the angle
of the chute deflector. Never attempt to clean out the snow blower, or adjust, repair, or maintain any
part with the tractor running.
Always choose caution and safety over speed. Snow removal can be very important, even urgent, but
one careless move can be far more serious.
SAFETY
B-4
Before making any repairs or adjustments, engage
the parking brake, lower attachment to the ground,
shut the engine off, and remove the key.
Read and understand the operator’s manual before
operating this equipment.
Attaching
1. Drive the tractor slowly forward into the hitch arms on the snow blower. Align the lift arms of the
tractor with the snow blower hitch arms by raising or lowering the front hitch and complete the
engagement.
2. Once completely engaged, close the front hitch locking lever
.*
3. Engage the parking brake* and shut off engine.
4. Place the attachment belt over the outside groove of the PTO drive pulley on the tractor. Ensure
the belt is properly seated in each pulley.
5. Engage the PTO spring tension lever.*
6. Wipe the quick couplers clean, and connect to the tractor. If equipped, connect the hoses and quick
couplers so the red indicators are paired together and the yellow indicators are paired together.
7. Connect the electric plug. (If equipped)
8. Engage the weight transfer system*. (If equipped)
Detaching
1. Park the tractor on a level surface and set the parking brake.*
2. Lower the snow blower to the ground.
3. Shut off tractor engine.
4. Disengage the PTO spring tension lever.*
5. Remove the attachment belt from the PTO drive pulley of the tractor.
6. Disconnect the hydraulic quick couplers from the tractor. Do not allow hoses and couplers to lay in
the dirt and snow.
7. Disconnect the electric plug. (If equipped)
8. Disengage the hitch locking lever.*
9. Restart tractor and slowly back away from the snow blower.
* Refer to tractor manual for operation of controls.
Operating Techniques & Tips
Always shift the tractor transaxle to low range when operating the snow blower.
Always direct the discharge chute toward open areas. Whenever possible, blow snow with the wind
direction and not against it. Rotate the chute to the desired direction using the auxiliary control. Adjust
the discharge deflector to the desired angle. Refer to chute adjustment on page D-2.
Lower the snow blower to the ground and place the S.D.L.A. lever in the float position by moving it
outward to the second position until the detent engages. The lever will stay in this position after
engagment. For proper skid shoe height adjustment, refer to page D-2.
With the tractor running at approximately 2000-2500 RPM, engage the PTO. Drive forward slowly,
keeping a close watch for potential hazards. Adjust the discharge chute rotation as necessary to keep
the discharged snow directed to open areas.
OPERATION
C-1
Lubrication
Grease the auger, jack-shaft, & blower shaft bearings every 25 hours. Do not over grease. Usually,
one or two pumps is sufficient. Additional lubrication may be required in extremely harsh or dirty
conditions.
Check the gearbox every 100 hours or seasonally. If necessary, add 80-90 weight gear oil. Gearbox
should be approximately half full.
Belt Replacement Venture Part #
PTO belt from the 4000 series tractor to the snow blower B50 81.B050
Auger drive belt (2) B50 81.B050
Gearbox drive belt B35 81.B035
Fan drive belt B55 81.B055
Optional top auger drive belt B40 81.B040
Fan Drive Belt Replacement
1. Remove the main drive cover form the snow blower.
2. Release the belt tension springs for the gearbox drive and the fan drive belts.
3. Remove the four bolts (See Figure 1) from the bracket that holds the rear blower shaft bearing.
4. Rotate the bracket as shown in Figure 2.
5. Remove the gearbox drive belt. Remove the old fan drive belt and install a new belt. Reinstall the
gearbox drive belt.
6. Rotate the bracket back into place and instal the four bolts.
7. Apply the belt tension springs for the gearbox drive and fan drive belts.
8. Reinstall the main drive cover.
D-1
MAINTENANCE/ADJUSTMENTS
Figure 1 Figure 2
Gearbox Drive, Auger Drive, & Top Auger Drive Belt Replacement
1. Remove the belt drive cover.
2. Release the belt tension spring and remove the old belt(s).
3. Install the new belt(s) and apply the belt tension spring.
4. Reinstall the belt drive cover.
Spring Tension Adjustment
The spring tension is adjustable for all the belts. This is to allow some belt slippage to protect the
gearbox and drive components in the event an immovable object stops the auger or fan. At the
factory, the spring is installed with a limited amount of tension. If required, the spring tension can be
increased.
Chute Adjustment
The discharge deflector can be hand adjusted to several different settings. Release the chute
adjustment link by pulling to the side and move the deflector to the desired angle. Re-engage the link.
With an optional electric actuator installed, the discharge deflector can be adjusted with a switch on
the dash of the tractor.
Skid Shoe Adjustment
Skid shoes are provided to keep the cutting edge off
the surface to be cleaned, especially when clearing
snow on gravel drives and roadways. To adjust the
skid shoes, park the tractor and snow blower on a
level surface. Raise the blower and set blocks of the
desired height under the cutting edge. (See Figure 3)
Lower the snow blower until it is resting on the
blocks. Loosen the skid shoe mounting bolts and
slide the skid shoes until they touch the ground.
Re-tighten the mounting bolts. Both the right and the
left skid shoes should be set at the same height.
Auger Housing Wear Edge Adjustment
After the skid shoes are adjusted to the correct
height, park the tractor and snow blower on a level surface. Lower the snow blower until the skid
shoes are resting on the ground. Set the auger housing wear edges approximately 1/4" above the
ground.
Vertical Cutting Edge Adjustment
The vertical cutting edges can be adjusted to provide either a 52" or 54" cutting width. If the shorter
flanges (2-7/8 - 3") are bolted to the snow blower, the cutting width is 52". If the longer flanges are
bolted to the snow blower, the cutting width is 54". To switch from one cutting width to the other,
rotate the cutting edges 180 degrees. Do not switch the cutting edges to opposite sides of the snow
blower. The left cutting edge has 15 degrees greater bend than the right.
MAINTENANCE/ADJUSTMENTS
D-2
Figure 3
ILLUSTRATED DRAWING
MAIN FRAME & AUGER DRIVE
PARTS
E-1
MAIN FRAME & AUGER DRIVE
E-2
PARTS
REF. PART NO. DESCRIPTION QTY.
1......80.0369 .............AUGER, ASM KX522.................................1
2......90.0612 .............BOLT,3/8-16 USSX11/2..............................4
3......64.1088 .............PLATE,AUGER PADDLE RETAINER ........................2
4......44.0181 .............PADDLE, 1/2" 3 PLY 3/8 X 1/16 ...........................2
5......99.A06N ............LOCKNUT, NYLON 3/8-16 ..............................4
6......85.K0610 ............KEY,3/8X11/4...................................1
7......99.SF08 ............NUT,SF1/2-13 USS ................................10
8......55.FB22023 ..........BEARING, FLANGE BLOCK 1-7/16" .........................2
9......95.08 ..............WASHER, FLAT 1/2 SAE...............................9
10......90.0812 .............BOLT,1/2-13 USSX11/2..............................4
11......83.SK23 ............BUSHING, 1 7/16" SK ................................1
12......83.2B110SK ..........PULLEY,2B11"2-GROOVE ............................1
13......90.0516 .............BOLT,5/16-18 USS X 2 ...............................3
14......81.B050.............BELT,B50 ......................................2
15......90.0824 .............BOLT,1/2-13 USS X 3 ................................1
16......41.0066 .............SPRING, SINGLE TORSION LH ...........................1
17......85.B0027 ............BUSHING, 1/2 ID X 5/8 OD X 5/8 ..........................2
18......40.0314 .............IDLER ARM, AUGER DRIVE.............................1
19......99.SF06 ............NUT,SF3/8-16 USS .................................1
20......95.06 ..............WASHER, FLAT 3/8 SAE ..............................12
21......83.0040 .............PULLEY, IDLER FLAT 5" PLAIN ...........................1
22......90.0616 .............BOLT,3/8-16 USS X 2 ................................1
23......90.0418 .............BOLT,1/4-20 USSX21/4..............................3
24......99.SF04 ............NUT,SF1/4-20 USS .................................6
25......62.1274 .............FRAME, MAIN KX522 ................................1
26......29.0093 .............PIPE, BREATHER PLUG 1/4.............................1
27......85.K0408 ............KEY,1/4X1.....................................2
28......83.SH16 ............BUSHING, 1" SH...................................1
29......83.2B36SH ...........PULLEY, 2 B 3.6" 2-GROOVE ............................1
30......90.0416 .............BOLT,1/4-20 USS X 2 ................................3
31......87.0219 .............GEARBOX, CW/CCW 1" SHAFT 2:1 ........................1
32......83.BK80H............PULLEY, 8" H-BUSH .................................1
33......83.H16S ............BUSHING, 1" SPLIT 1/4" KEY ............................1
34......90.0406 .............BOLT,1/4-20 USS X 3/4 ...............................2
35......96.06 ..............WASHER, LOCK 3/8 .................................4
36......90.0608 .............BOLT,3/8-16 USS X 1 ................................4
37......99.SF0506 ...........BOLT,SF5/16-18 USS X 3/4 ............................6
38......60.0873 .............GUIDE, THROAT ...................................1
39......99.SF05 ............NUT,SF5/16-18 USS ................................8
40......90.0814 .............BOLT,1/2-13 USSX13/4..............................4
41......60.0982 .............SHIELD, STUB SHAFT................................1
42......99.SF0504 ...........BOLT,SF5/16-18USS X 1/2 .............................2
43......64.1283 .............BRACKET, AUGER INSTALL ACCESS .......................1
44......29.B0204G ...........PIPE, BUSHING 1/8 X 1/4 GALV...........................1
ILLUSTRATED DRAWING
MAIN DRIVE & FAN DRIVE
PARTS
E-3
MAIN DRIVE & FAN DRIVE
E-4
PARTS
REF. PART NO. DESCRIPTION QTY.
1......90.0610 .............BOLT,3/8-16 USSX11/4..............................3
2......83.Q123 ............BUSHING, 1 7/16" Q1 ................................2
3......80.0344 .............BLOWER, SNOWBLOWER .............................1
4......99.SF04 ............NUT,SF1/4-20 USS .................................8
5......99.SF08 ............NUT,SF1/2-13 USS .................................8
6......95.08 ..............WASHER, FLAT 1/2 SAE...............................8
7......41.0066 .............SPRING, SINGLE TORSION LH ...........................2
8......85.B0027 ............BUSHING, 1/2 ID X 5/8 OD X 5/8 ..........................4
9......40.0312 .............IDLER ARM, GEAR BOX KX.............................1
10......90.0824 .............BOLT,1/2-13 USS X 3 ................................2
11......90.0612 .............BOLT,3/8-16 USSX11/2..............................5
12......83.0037 .............PULLEY, IDLER FLAT 4" X 3/8............................2
13......95.06 ..............WASHER, FLAT 3/8 SAE...............................2
14......99.SF05 ............NUT,SF5/16-18 USS ................................4
15......90.0406 .............BOLT,1/4-20 USS X 3/4 ...............................4
16......83.H16S ............BUSHING, 1" SPLIT 1/4" KEY ............................2
17......83.2BK32H ...........PULLEY, 2BK 3.2" H-BUSH .............................1
18......55.FB16016-1 .........BEARING, FLANGE BLOCK 1" ...........................2
19......90.0410 .............BOLT,1/4-20 USSX11/4..............................3
20......85.K0408 ............KEY,1/4X1.....................................2
21......80.0345 .............JACKSHAFT, 1" TGP X 13-1/4 KX ..........................1
22......81.B035.............BELT,B35 ......................................1
23......99.SF0508 ...........BOLT,SF5/16-18 USS X 1..............................4
24......83.BK75H............PULLEY, 7.5" .....................................1
25......81.B050.............BELT,B50 ......................................1
26......40.0313 .............IDLER ARM, FAN DRIVE KX.............................1
27......90.0414 .............BOLT,1/4-20 USSX13/4..............................1
28......81.B055.............BELT,B55 ......................................1
29......90.0816 .............BOLT,1/2-13 USS X 2 ................................4
30......90.0606 .............BOLT,3/8-16 USS X 3/4 ...............................4
31......95.06 ..............WASHER, FLAT 3/8 SAE...............................4
32......64.1085 .............SUPPORT, BLOWER BEARING KX .........................1
33......99.SF06 ............NUT,SF3/8-16 USS .................................6
34......55.PB22023 ..........BEARING, PILLOW BLOCK 1 7/16 .........................2
35......83.TB124 ............PULLEY .......................................1
36......80.0346 .............SHAFT, THROWER FAN ...............................1
37......85.K0610 ............KEY,3/8X11/4...................................2
38......64.1099 .............PLATE,BEARING REINFORCEMENT .......................2
39......64.1100 .............BUSHING, 1-1/2X2X7/8 ..............................1
40......99.B0031 ............WASHER, MACH 1 1/2 14GA ..........................A/R*
41......99.B0054 ............WASHER, MACH 1 1/2 10GA ..........................A/R*
42......64.1249 .............SHIM, BEARING KX//LX .............................A/R*
* as required.
ILLUSTRATED DRAWING
CHUTE & HYDRAULICS
PARTS
E-5
CHUTE & HYDRAULICS
E-6
PARTS
REF. PART NO. DESCRIPTION QTY.
1......62.0992 .............CHUTE, FINAL EXT. SNOWBLOWER ........................1
2......90.0506 .............BOLT,5/16-18 USS X 3/4 ..............................17
3......95.05 ..............WASHER, FLAT 5/16 SAE .............................17
4......05.0055 .............WASHER, NYLON .34 X .74 X .062 .........................8
5......99.A05 .............LOCKNUT, STOVER 5/16-18 USS ..........................8
6......62.0991 .............CHUTE, MIDDLE SNOWBLOWER .........................1
7......99.SF05 ............NUT,SF5/16-18 USS ................................9
8......42.0461 .............LINK, CHUTE CONTROL ..............................2
9......99.A06 .............LOCKNUT, STOVER 3/8-16 USS ..........................1
10......95.06 ..............WASHER, FLAT 3/8 SAE...............................2
11......41.0039 .............SPRING, COMP. 9/16 OD X 5/8 ...........................1
12......42.0462 .............LINK, CHUTE ADJUSTMENT ............................1
13......62.0990 .............CHUTE, MAIN SNOWBLOWER KX520 .......................1
14......90.0816 .............BOLT,1/2-13 USS X 2 ................................1
15......90.0612 .............BOLT,3/8-16 USSX11/2..............................1
16......60.0872 .............SHIELD, ROTATOR CHAIN COVER .........................1
17......99.SF0404-1 ..........BOLT,SF1/4-20 X 1/2 W/RUBBER .........................4
18......99.SF04 ............NUT,SF1/4-20 USS .................................4
19......83.H409 ............SPROCKET, #40 9-T HRD 5/8 BORE ........................1
20......85.K0307 ............KEY,3/16X5/8....................................1
21......91.0404 .............BOLT,1/4-28 SAE X 1/2 ...............................3
22......05.0040 .............GROMMET,1 1/2ID,2-3/8OD,3/32T .........................1
23......62.1000 .............MOUNT, MOTOR HYD. ...............................1
24......85.B0027 ............BUSHING, 1/2 ID X 5/8 OD X 5/8 ..........................1
25......99.SF08 ............NUT,SF1/2-13 USS .................................2
26......21.0113 .............MOTOR,HYDPEERLESS 1.93 CU.IN .......................1
27......23.0104 .............COUPLER, HYD. QUICK MALE 1/4 .........................2
28......29.0092 .............FITTING, .025 ORIFICE 1/4 PIPE ..........................1
29......20.0210 .............HOSE, ASM C 1/4 X 78"-2750 ............................2
30......62.0993 .............POST, CHUTE MOUNT ...............................1
31......99.A04 .............LOCKNUT, STOVER 1/4-20 USS ..........................1
32......64.0673 .............CLAMP, HYD. HOSE 3/8-1/4 .............................1
33......90.0410 .............BOLT,1/4-20 USSX11/4..............................1
34......00.0123 .............DECAL, KEEP HAND AND FEET AWAY ......................2
35......81.0147 .............CHAIN, ROLLER #40 X 30-7/8 SS .........................1
36......81.0056-1............LINK, CONN. #40 SS ................................1
37......95.04 ..............WASHER, FLAT 1/4 SAE...............................1
38......05.0117 .............WASHER, .544ID x .817 x.14 YEL ..........................1
39......05.0116 .............WASHER, .544ID x .817 x.14 RED..........................1
ILLUSTRATED DRAWING
SHIELDS, DECALS, & CUTTING EDGE
PARTS
E-7
SHIELDS, DECALS, & CUTTING EDGE
E-8
PARTS
REF. PART NO. DESCRIPTION QTY.
1......97.0608 .............BOLT,CARRIAGE 3/8 X 1 .............................14
2......78.0054 .............CUTTING EDGE, 47" THRU HARD .........................1
3......99.SF06 ............NUT,SF3/8-16 USS ................................18
4......00.0189 .............DECAL, VENTRAC ORBITAL ............................1
5......00.0062 .............DECAL, DANGER SHIELD MISSING ........................2
6......60.0868 .............SHIELD, AUGER DRIVE BELT ...........................1
7......90.0406 .............BOLT,1/4-20 USS X 3/4 ...............................8
8......95.04 ..............WASHER, FLAT 1/4 SAE...............................8
9......00.0100 .............DECAL, MADE IN USA................................1
10......99.SF04 ............NUT,SF1/4-20 USS .................................5
11......99.E0046 ............NUT,“U”1/4-20 EXTRUDED .............................4
12......60.0870 .............SHIELD, GEARBOX DRIVE .............................1
13......95.06 ..............WASHER, FLAT 3/8 SAE...............................2
14......90.0606 .............BOLT,3/8-16 USS X 3/4 ...............................2
15......47.0167 .............KNOB, 1/4-20 X 1-1/4 DIA BLK ...........................1
16......60.0869 .............COVER, DRIVE PULLEY KX.............................1
17......00.0122 .............DECAL, THROWN OBJECT HAZARD........................1
18......00.0101 .............DECAL, HAZARD-MOVING PART ..........................1
19......60.0871 .............COVER, GEAR BOX/FAN BELT KX .........................1
20......94.05 ..............WASHER, FLAT 5/16 USS ..............................4
21......64.1087 .............SHOE, SKID KX/LX .................................2
22......00.0220 .............DECAL, GENERAL SAFETY .............................1
23......00.0208 .............DECAL, DANGER AUGER HAZARD ........................2
24......99.SF0506 ...........BOLT,SF5/16-18 USS X 3/4 ............................8
25......60.0983 .............CUTTING EDGE, VERTICAL RIGHT ........................1
26......99.SF05 ............NUT,SF5/16-18 USS................................12
27......60.0878 .............CUTTING EDGE, VERTICAL LEFT .........................1
28......99.SF0606 ...........BOLT,SF3/8-16 USS X 3/4 .............................4
29......60.0981 .............WEAR EDGE, AUGER HOUSING KX522 ......................1
30......90.0506 .............BOLT,5/16-18 USS X 3/4 ..............................4
31......95.05 ..............WASHER, FLAT 5/16 SAE ..............................4
32......60.0885 .............GUARD, SNOWBLOWER CHUTE..........................1
33......60.0984 .............WEAR EDGE, AUGER HOUSING LEFT.......................1
34......00.0217 .............DECAL, WARNING READ OWNERS MAN .....................1
ILLUSTRATED DRAWING
12 VOLT ACTUATOR DEFLECTOR CONTROL
PARTS/OPTIONS
F-1
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Walker Combined Decks User manual
-
-
Frontier SB1174 User manual
-
Bercomac Berco 700255-1 Owner's manual
-
Gravely ma211 User manual
-
John Deere SB1148 User manual
-
Woods SB64S User manual
-
Woods Equipment SB74S User manual
-
-
Walker Rider Lawnmowers SB36 User manual
