LG Electronics LMV1680WW User manual

Website: http://us.lgservice.com

MICROWAVE OVEN

INSTALLATION INSTRUCTIONS

PLEASE READ AND SAVE THESE INSTALLATION INSTRUCTIONS.

P/NO.: 3828W5U0529

– 2 –

Your Safety First

BEFORE YOU START

• Proper installation is the installer's responsibility!

– Read the entire manual before you begin. The model number label is located on the oven front.

See Figure 1. The mounting plate is located on back side of microwave oven. See Figure 2.

NOTE: Vent grille appearance varies by model.

BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS:

• You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled

properly.

• Avoid Electrical Shock!

– Before you drill into the wall, note where electrical outlets are and where electrical wires might be concealed

behind the wall. YOU COULD GET AN ELECTRIC SHOCK if you contact electrical wires with your drill bit.

– Locate and disconnect the power to any electrical circuits that could be affected by installing this oven.

IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.

• ELECTRICAL RATING OF THIS OVEN : 120V AC 60Hz.

– You need a DEDICATED 120V, 60Hz, AC only, 15 or 20A, fused electrical supply (located in the cabinet

above the microwave as close as possible to the microwave) serving only the microwave.

Model Number Plate

Mounting Plate

Figure 1 Figure 2

For Your Safety

WARNING

Label Cooking Guide

• This oven should not be installed or located by anyone except properly qualified service personnel.

– 3 –

Your Safety First

• THIS APPLIANCE MUST BE GROUNDED!

– If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape

wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding

plug.

• Place the plug into a properly installed and grounded outlet. See Figure 3.

• Do not use an extension cord.

• Keep the power cord dry and do not pinch or crush it.

• DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE

POWER SUPPLY CORD GROUNDING PRONG!

This appliance MUST be grounded!

Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do not

completely understand the grounding instructions.

DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.

SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.

• DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY!

– DO NOT try to operate the microwave oven with the door open.

– DO NOT tamper with or defeat the safety interlocks.

– DO NOT place objects between the microwave oven front face and the door.

– DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.

– DO NOT operate the microwave oven if it is damaged.

– The microwave oven door must close properly to operate safely.

– DO NOT USE THE MICROWAVE OVEN:

• If the door is bent.

• If the hinges or latches are broken or loose.

• If the door seals, sealing surfaces or glass is broken.

– DO NOT ATTEMPT TO ADJUST OR REPAIR THE OVEN YOURSELF!

It should be adjusted and repaired by a qualified technician who can check for microwave leakage after

repairing the oven.

PROPERLY POLARIZED AND

GROUNDED OUTLET

Three-Pronged (Grounding) Plug

Figure 3

If you use the grounding plug improperly, you risk electric shock and/or fire!

WARNING

Improper grounding could result in electric shock, fire or other personal injury.

WARNING

If you do not use the microwave oven as instructed,

you could be exposed to excessive microwave energy.

WARNING

– 4 –

Your Safety First

• MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.

– Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed of

minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.

– ATTACH (See note on page 5) the two lag screws supporting the oven to a vertical, 2" x 4" wall stud.

– DO NOT mount the microwave oven to an island or peninsula cabinet.

– BE SURE the upper cabinet and rear wall structures can support 150 lbs., plus the weight of any

items you place inside the oven or upper cabinet.

– Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.

– BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.

CAUTION

• Before you begin installing the oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY

MATERIAL (a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover.

Failure to protect these surfaces could result in property damage.

30" min. cabinet opening width

30" min. clearance from bottom

of cabinet to cooking surface

or countertop before installation.

Grounded Outlet

(inside upper cabinet)

Power Supply Cord Hole

(Use templates included

with installation instructions)

Figure 4

If you do not mount the oven as instructed,

you risk personal injury and/or property damage.

WARNING

– 5 –

Parts, Tools, Materials

THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:

NOTE: Depending on your ventilation requirements, you may not use all of these parts.

Damper/duct connector

(for roof venting or wall venting installation)

Not Actual Size (2 pieces must be assembled as

shown) Not used if venting into kitchen.

One power cord clamp and

One dark-colored mounting screw

(to hold the power cord)

Actual Size

Four 1/4" x 2" lag screws - Actual Size

(for wall stud holes)

Four 1/4" x 3" toggle bolts - Actual Size

(for drywall holes)

Two 1/4" x 3" bolts - Actual Size

(for securing to the upper cabinet

Four 1/4" x 3" bolts - Actual Size

(for securing to the upper cabinet)

Two tapping screws - Actual Size

(for attaching the damper duct connector)

One upper cabinet template- Not Actual Size

REAR WALL TEMPLATE

CAUTION — IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE

RECOMMENDED DIMENSION, GREASE LADEN AIR WILL

DISCHARGE INTO HOUSE STRUCTURE.

LINE UP WITH

PREVIOUSLY

DRILLED HOLE

LINE UP WITH

PREVIOUSLY

DRILLED HOLE

Printed in Korea

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.

This template is for locating the wall venting

cutout. Do not use this template for roof

or room venting.

1.Place the template flat against the rear

wall, aligning circles A and B with the

corresponding holes previously drilled in the

rear wall for holes A and B of the wall plate.

2.With the template aligned to the holes, tape the

template to the rear wall.

3.Use a saber or keyhole saw to cut out the shaded

area F through the rear wall.

4.Remove the template from the rear wall.

RETURN TO AND PROCEED WITH THE

INSTALLATION INSTRUCTIONS.

1/4

P/N. 4922W5A060A

F. CUT OUT FOR WALL

VENTED ONLY

CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR

One rear wall template- Not Actual Size

(3 pieces mounting plate only)

One power cord clamp bushing - Actual Size (for the cord hole in a metal upper cabinet)

NOTE: You need to install at least two lag screws into a 2" x 4" stud and four anchor bolts into the wall.

and the mounting area must meet the 150 lbs. weight requirement.

– 6 –

Parts, Tools, Materials

Clear Tape

(for taping the templates to the wall)

Phillips Screwdriver

(for the screws)

Pencil

Flat Blade Screwdriver

(for the toggle bolts)

Plumb Line

Measuring Tape

(metal preferred)

Duct Tape

Small Side Cutters or Tin Snips

Caulking Gun and Caulk

Stud Finder or Thin Nail

Saber Saw

(for cutting vent holes for roof

or wall vending)

Keyhole Saw (for the power cord hole)

You will need the following tools and materials for the installation:

Carton or other heavy material such as a blanket for covering the counter top.

3/8" and 3/4" wood drill bits

1/2" and 3/16"

drill bits

Electric Drill

●

If you have brick or masonry walls, you will need special hardware and tools.

●

The ductwork you need for the installation is not included. All wall and roof caps must have a back-draft damper.

(Shown on page 5).

– 7 –

STEP 1: Prepare The Electrical Connection

Improper grounding could result in electric shock or other personal injury.

1. Locate the grounded electric outlet for this oven in the

cabinet above the oven, as shown in Figure 5.

NOTE: The outlet should be on a circuit dedicated to the

microwave oven (120V, 60 Hz., AC only) with a 15 or 20A

fused electrical supply.

IMPORTANT: If you do not have the proper wall outlet,

you MUST have one installed by a qualified electrician.

2. You will cut the hole for the power supply cord (shown in

Figure 5) later when you prepare the wall and upper cabinet in

Step 4.

NOTE: Do not use an extension cord.

Keep the power cord dry and do not pinch or crush it.

DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY CORD

GROUNDING PRONG!

This appliance MUST be grounded!

WARNING

AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED!

WARNING

Upper

Cabinet

Power-Supply-Cord Hole

Figure 5

Grounded Outlet

(Inside Cabinet)

– 8 –

STEP 2: Prepare The Venting System

THIS OVEN MUST BE PROPERLY VENTED!

WARNING

NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork

fittings and length are shown in Figure 10, page 9.

You may vent your oven in one of three ways. However, do NOT vent into a wall cavity, an attic, or an unused

area.

Roof-venting If your oven is located on an outside wall near the roof, as in Figures 7 (3 1/4" x 10" duct) and

Figure 9 (6" round duct.)

Wall-venting If your oven is located on an outside wall of your house, as in Figure 6 (3 1/4" x 10" duct) and

Figure 9 (6" round duct.)

Room-venting If your oven is located on an inside wall of your house, as in Figure 8.

NOTE: If you choose the rear exhaust method (roof or wall-venting), be sure there is enough clearance within the

wall for the exhaust duct.

REMEMBER AS YOU INSTALL THE

VENTING:

Keep the length of the ductwork and the number

of elbows to a minimum to ventilate your oven

efficiently. See examples on page 9.

Keep the size of the ductwork the same.

Do not install two elbows together.

Use duct tape to seal all joints in the duct system.

Use caulking to seal the exterior wall or roof

opening around the cap.

Cabinet

Oven

Wall Mounting

Through-the-wall Duct

Wall Cap

3 1/4"x10"

Duct

Cabinet

Oven

Figure 6

Wall Venting

Through-the-roof

3 1/4"x10"

Duct

Roof Cap

Roof Venting

Cabinet

Oven

Figure 7

Roof Venting

Figure 8

Room Venting

6"min diameter

Round Duct

3 1/4" to Round

Duct Transition

3 1/4" to Round

Ductwork Transition

Roof Cap

Wall Cap

Elbow

Figure 9

– 9 –

STEP 2: Prepare The Venting System

Standard Fittings

NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension

duct installed between the damper assembly and the adapter to prevent the exhaust damper’s sticking.

Duct Length

The total length of the duct system, including straight duct, elbows, transitions, and wall or roof caps must not

exceed 140 feet.

For best performance, do not use more than three 90 degree elbows, and keep the length as short as possible.

Below are the standard fittings and their equivalent length in feet.

To calculate the equivalent length of each duct piece used, see the examples below.

Figure 10

6ft.

2ft.

wall cap

6ft.

transition

wall cap

For 3 1/4" x 10" SYSTEMS

1 3 1/4” x 10” 90° elbow = 25 ft.

1 Wall Cap = 40 ft.

8 feet straight duct = 8 ft.

TOTAL LENGTH = 73 ft.

1 transition = 5 ft.

2 90° elbows = 20 ft.

1 Wall Cap = 40 ft.

8 feet straight = 8 ft.

TOTAL LENGTH = 73 ft.

For 6" ROUND SYSTEMS

3 1/4” x 10”

to 6" = 5 ft.

90˚elbow

= 10 ft

45˚elbow

= 5 ft

3 1/4” x 10”

wall cap

= 40 ft

3 1/4” x 10”

flat elbow

= 10 ft

3 1/4” x 10” roof

cap = 24 ft

3 1/4” x 10” 90˚

elbow = 25 ft

1 2 3

4 5 6 7

Examples

– 10 –

STEP 3: Prepare The Venting Blower

Your microwave oven is shipped with the blower assembled for room-vented. You need to adjust the blower if you

want wall-vented or roof-vented installation.

• DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in

electrical shock.

REMOVE THE MOUNTING PLATE:

1. Remove any shipping materials and parts from inside the

microwave oven. Set them aside for later use.

2. Cover the counter top or cooktop with a thick, protective

covering to protect it from damage and dirt. See Figure 11.

NOTE: If you have a free-standing range, disconnect

it, move it onto a piece of cardboard or hardboard and

pull it away from the wall, so that you can get closer to

the upper cabinet and back wall for easier measuring

and drilling.

3. Remove mounting plate screw(s) (1 or 2 screws) from the

mounting plate as shown and discard the screws.

See Figure 12.

4. This plate will be used as the rear mounting plate. (It will be

used to locate and mark the mounting holes on the rear wall.)

5. Locate exhaust adaptor, grease filters and hardware packet.

6. At this point, remove any adhesive tape (if there is any), on the

exhaust adaptor, the grease filters and the power supply cord.

ROOM-VENTED INSTALLATION:

This oven is shipped assembled for room-vented. You need to

go to

STEP 4: PREPARE THE WALL & UPPER CABINET

located

on page 13 .

A thick, protective

covering

Mounting plate

Control Panel Side

Mounting Plate

Screws

Mounting Plate

Control Panel Side

Mounting Plate

Screw(s)

(1 or 2 screws)

Figure 11

Figure 12

ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT.

WARNING

– 11 –

STEP 3: Prepare The Venting Blower

WALL-VENTED INSTALLATION:

1. Remove one blower unit mounting screw and one or

several blower plate mounting screw(s). Remove the

blower plate from cabinet. See Figure 13.

2. Carefully lift the blower unit out of the microwave oven.

3. Use side cutters or tin snips to cut and remove knockouts

B from Back plate. Discard knockouts. Be careful not to

distort the plate. See Figure 14.

4. Reassemble the blower wire. See Figure 15.

5. Rotate the blower unit so that the exhaust ports face the

rear of the cabinet. See Figure 16.

6. Place blower unit back into cabinet. Check that the exhaust

ports face towards the rear of the cabinet. Be sure the

wires are not pinched. See Figure 17.

7. Reattach the blower plate to cabinet so the exhaust ports

and blower plate opening are aligned. Attach with one

blower unit mounting screw and then one or several blower

plate mounting screw(s). See Figure 18.

Figure 13

Blower Plate

Mounting Screw

Blower Plate

Back Plate

Blower Unit

Mounting Screw

Blower Unit

Parts B

Figure 14

Parts B

Knockouts Parts B

Blower

Unit

Exhaust Ports

Figure 15

Figure 16

Figure 18

Blower Plate

Mounting Screw

Blower Plate

Back Plate

Blower Unit

Exhaust Ports

Blower Unit

Mounting Screw

Figure 17

Exhaust

Ports

– 12 –

STEP 3: Prepare The Venting Blower

ROOF-VENTED INSTALLATION:

1. Remove one blower unit mounting screw and

one or several blower plate mounting screw(s).

Remove the blower plate from cabinet. See

Figure 19.

2. Carefully lift the blower unit out of the microwave

oven.

3. Rotate blower unit 90 so the exhaust ports face

the top of the cabinet. See Figure 20.

4. Place blower unit back into microwave oven.

5. Use side cutter or tin snips to cut and remove knockouts

"A" from blower plate. Discard knockouts. Be careful not

to distort the plate. See Figure 21.

6. Reattach blower plate to microwave oven.

Attach with the one blower unit mounting screw and then

the two blower plate mounting screws. See Figure 22.

Figure 19

Figure 20

Blower Unit

blower plate

mounting

screws

blower unit

mounting screw

blower plate

Knockouts "A"

Figure 21

blower unit

mounting screws

blower unit

blower plate

mounting

screws

Figure 22

– 13 –

STEP 4: Prepare The Wall & Upper Cabinet

To avoid personal injury or property damage, do not attempt to install this microwave

oven if you cannot find a wall stud. Consult a carpenter or contractor.

WARNING

Upper Cabinet Template

Mounting Plate

(1-piece Mounting Plate)

(3-piece Mounting Plate)

Upper Cabinet Template

Mounting Plate

Measure And Track/Tape Up The Templates

1. Using a plumb line and (metal) measuring tape, find and

mark the vertical center line on the back wall, as in

Figure 23.

2. Find and mark one or two points where the studs are on

the wall. (Studs are normally 16 inches apart). Then

measure and mark the stud locations. If you cannot find

any wall stud, consult a local building contractor.

3. Line up the plumb line on the wall with the center line

on the mounting plate.

NOTE: Be sure the minimum width is 30 inches and the

distance from the top of the wall template to the

range or counter top is at least 30 inches. See

Figure 23.

4. Center mounting plate in operating by lining up the

plumb line on wall with centerline on mounting plate.

Make sure the minimum width is 30 inches and that the

top of the mounting plate is located a minimum of 30

inches above the cooking surface. See Figure 24.

NOTE: If the cabinets are not plumb, adjust the mounting

plate to the cabinets. If the front edge of the

cabinet is lower than the back edge, adjust the

mounting plate to be level with the cabinet front.

5. Measure the bottom of the upper cabinet frame. Trim

the edges A, B, and C on the upper cabinet template

so that the template will fit on the bottom of the upper

cabinet. If upper cabinet has a recessed frame, trim the

template so it fits inside the recessed area. Align the

centerline of the upper cabinet template with the

centerline of the mounting plate, then securely tape or

tack the upper cabinet template in place. See Figure

24.

DO NOT ATTEMPT TO INSTALL THE MICRO-

WAVE OVEN IF YOU CANNOT FIND A WALL

STUD.

CAUTION

Figure 23

Figure 24

– 14 –

STEP 4: Prepare The Wall & Upper Cabinet

Drill The Holes In The Wall And Upper Cabinet.

1. Drill holes on the circles. If there is a stud, drill a 3/16

hole

for lag screws. If there is no stud, drill a 3/4

hole for toggle

bolts. Make sure to use at least 2 lag screws in a stud, and

4 toggle screws in the drywall or the plaster.

2. Drill a 3/8” hole at points J and K on the upper cabinet

template.

NOTE: If the bottom of the upper cabinet is recessed 3/4

or more, you will need 2

x 2

filler blocks (not

included) to provide additional support for the bolts.

See Figure 25.

Mark the center of each filler block and drill a 3/8”

diameter hole at the marks.

Align filler blocks over the two openings in the top

of the microwave oven cabinet and attach to

cabinet with masking tape. See Figure 26.

3. Cut or drill a 2

diameter hole at the area marked M. Power

supply cord hole on the upper cabinet template. If the upper

cabinet is metal, you will need to cover the edge of the hole

with the power supply cord bushing (supplied) to prevent

damage to the cord from the rough metal edge.

4. Cut out the venting areas (with the saber saw):

Roof-Vented: cut out the shaded area marked L on the

upper cabinet template.

Wall-Vented: Tape the rear wall template to the rear wall,

lining up with the holes previously drilled for holes A and

B in the plate. Cut out the shaded area marked F on the

REAR WALL TEMPLATE.

Room-Vented: go to STEP 5, INSTALL THE MOUNTING

PLATE, located on page 15.

5. Complete whichever venting system you have chosen. Use

caulking compound to seal the exterior wall or roof opening

around the wall cap or roof cap.

Figure 25

Figure 26

Cabinet Front

Cabinet

Bottom Shelf

Filler Block

Filler

Block

To avoid risk of personal injury, electrical shock or death:

Note where electrical outlets and electrical wires are before you drill into the wall.

Locate and disconnect power to any electrical circuits that could be affected by

installing this oven.

WARNING

To avoid risk of personal injury, electrical shock or death, cover the edge of the power

supply cord hole with the power supply cord bushing.

WARNING

– 15 –

STEP 5: Install The Mounting Plate

Center Line

Draw

Center Line

Draw Lines

on Studs

For Wall-

Vented Only

Minimum 66

From the Floor

Support Tab Support Tab

Mounting

Plate

3/16 Hole on Studs

5/8 Hole on Drywall Only

3/16 Hole on Studs

5/8 Hole on Drywall Only

Center Line

Draw

Center Line

Draw Lines

on Studs

For Wall-

Vented Only

Minimum 66

From the Floor

Support Tab Support Tab

Mounting

Plate

(1-piece Mounting Plate)

(3-piece Mounting Plate)

The Oven Must Be Connected To At Least One

Wall Stud.

1. Draw a vertical line on the wall at the center of the 30" wide

space. Use the mounting plate as the template for the rear

wall. Place the mounting plate on the wall, making sure that

the tabs are against the bottom of the cabinet. Line up the

notch and center line on the mounting plate to the center line

on the wall.

2. While holding the mounting plate with one hand, draw circles

on the wall at holes A, B, C, and D. Four holes must be used

for mounting. If the holes are not used, the installation will not

be secure. Installer must use these holes for proper

installation. Use toggle bolts through these holes unless one

of them lines up with a stud. Use a wood screw for studs.

NOTE: Draw a fifth circle inside area E, through one of the

bottom holes to match the location of a stud. For wall-

vented: The oven requires a rear wall cutout opening for

the rear wall duct and the exhaust adaptor must be

attached to the mounting plate. See the next page on

how to prepare the rear wall cutout opening and the

exhaust adaptor/mounting plate for wall-vented.

3. Drill holes on the circles. If there is a stud, drill a 3/16 hole for

lag screws. If there is no stud, drill a 5/8 hole for toggle bolts.

Make sure to use at least 1 lag screw in a stud, and 4 toggle

bolts in the drywall or the plaster.

4. Attach the plate to the wall. To use spring toggle head bolts:

Remove the toggle wings from the bolts. Insert the bolts into

the mounting plate and replace the spring toggle head to 3/4

past the bolt ends. Insert the spring toggle head into the

holes in the wall to mount the plate. You may pull forward on

the plate to help in tightening the toggle bolts. Tighten all

bolts.

Figure 28

Figure 27

Wall

Mounting

Plate

Space More Than Wall Thickness

Bolt

End

Toggle Bolt

Toggle Wings

– 16 –

STEP 5: Install The Mounting Plate

Slide exhaust

adaptor into

guides on

rear panel.

Exhaust Adaptor

Damper

(hinge side up)

Locking

Tabs

Guides

Mounting Plate

Back Plate

(1-piece

Mounting Plate)

(3-piece

Mounting Plate)

For Wall-Vented

Make the box cutout for the rear wall duct.

– 1-piece mounting plate:

Using a pencil, put dots through slots F and G, and

through holes H and I. Remove the mounting plate and

draw lines extending through the points. This will give

the location and size of the box cutout for the rear wall

duct. (Figure 29)

– 3-piece mounting plate:

Use the wall template to determine the location and size

of the box cutout for the rear wall duct.

Attach the exhaust adaptor to the rear mounting plate

(back plate) wall side. Push in securely until it is past the

top locking tabs and in the lower locking tabs. Take care to

assure the damper hinge is installed so that it is at the top

and that the damper swings freely.

Carefully guide the exhaust adaptor, now attached to the

mounting plate, into the house duct. Before using the

screws to attach the plate to the wall. This will assure

proper alignment for installation.

After completing the installation of the mounting plate,

again check the rear damper for free movement to assure

it will operate properly.

Figure 29

Figure 30

– 17 –

STEP 6: Attach The Oven To The Wall

1. Carefully lift microwave oven and hang it on support tabs

(See Figure 27) at the bottom of the mounting

plate.Reaching through upper cabinet, thread

power supply cord through the power supply cord

hole in the bottom of the upper cabinet.

See Figure 31.

2. Rotate the microwave oven upward so the top of

oven is against the bottom of the upper cabinet or cabinet

frame.

3. Then insert a bolt down through each hole in the

upper cabinet bottom.See Figure 32.

Tighten the bolts until the gap between the upper cabinet

and microwave oven is closed.

4. If wall-vented or room-vented installation is used,go to No.

7 on the next page.

Figure 31

Figure 32

Power Cord

Hole

To avoid risk of personal injury or property damage, you will need two people to

install this microwave oven.

WARNING

– 18 –

STEP 6: Attach The Oven To The Wall

Damper

Power

supply

Cord

Clamp

5. Roof venting installation: See Figure 33.

Install ductwork through the vent opening in the

upper cabinet. Complete the venting system through the

roof according to the method needed. See

Prepare The

Venting System

STEP 2.

Use caulking gun to seal the exterior roof opening around

the exhaust cap. See Figure 7 on page 8.

6. Use the power supply cord clamp to bundle the power

supply cord. Install the power supply cord clamp, using a

screw as shown in Figure 34, to inside of the cabinet.

7. Grasp filter screen with one hand holding the ring and the

other hand holding the opposite end. Insert the end of the

filter screen without ring into the opening and slide

towards the side of the microwave oven. Insert ring end of

filter screen into the opening and slide entire screen

towards the center of the microwave until screen is

securely in position. Repeat for other filter screen. See

Figure 35.

8. Plug in the power supply cord.

9. Read your Owner’s Manual, then check the operation of

your microwave oven.

Figure 33

Figure 34

Figure 35

Printed in China

LG Electronics LMV1680WW User manual

Related papers

Other documents