Nortek Contol WOR User manual

Brand: Nortek Contol

Model: WOR

Type: User manual

This manual is also suitable for

INSTR,INST,WOR

Linear P/N: 212902 C

Material: 20 Lb. Mead Bond

Size: 8.500" x 11.000"

Ink: Black

Side 1 of 2

Scale: 1-1

WOR

Wiegand

Output

Receiver

Installation

Instructions

INTRODUCTION

The Model WOR remote radio receiver is designed for use as an access control interface for Linear’s block coded

digital transmitters. The unit receives signals from transmitters, adds a facility code to the data, and sends the

information to the Wiegand input of the access control panel via a 5-wire connection.

Several transmitter and receiver options can be set using the unit’s dipswitches. Three different Wiegand output

formats (26, 30, & 31-bit) are supported. Three receiver options (lockout, hold, & button offset) can be set.

Transmitter buttons on multi-button units can be selectively disabled. The facility code is set using 16 dipswitches.

Three antenna types can be used with this receiver. The local whip antenna (supplied) screws directly on to the

receiver. The directional (EXA-2000) and omni-directional (EXA-1000) remote antennas attach to the receiver’s

antenna input via RG-59 cable and a type “F” connector.

An on-board RADIO RANGE knob allows adjustment of the receiver’s gain. It can be set to limit the maximum

radio range that the receiver can achieve. Two indicators display the receivers performance and operation. The

red RADIO indicator lights when the receiver detects a radio signal. The two color red/green STATUS indicator

lights green when the receiver is sending Wiegand data and during the 1-second post receiver lockout timer (if

receiver lockout is enabled). The indicator turns red when the receiver’s HOLD input (connected to the access

control panel) is active. Receiver test points are provided for listening to the incoming signals with an audio

amplifier.

Power input to the receiver can be either regulated 5 volts or 8-24 volts DC (jumper selected).

The receiver is housed in a weather-resistant enclosure and can be mounted indoors or outdoors. Gaskets and

a weather-tight wiring strain relief seal the unit from the elements.

1. OPEN CASE 2. LOCATE COMPONENTS

3. SET VOLTAGE INPUT JUMPER 4. SET OUTPUT FORMAT & RECEIVER OPTIONS

(760) 438-7000 • FAX (760) 438-7043

USA & Canada (800) 421-1587 & (800) 392-0123

Toll Free FAX (800) 468-1340

www.linearcorp.com

OPEN CASE FROM

ANTENNA END

REMOVE FOUR

SCREWS AND WASHERS

BOARD SLIDES OUT

FROM 3RD SLOT UP

INSIDE CASE

5. SET TRANSMITTER FACILITY CODE 6. SET TRANSMITTER BUTTON OPTIONS

ANTENNA

CONNECTOR

(HIDDEN)

RADIO RANGE KNOB

(CLOCKWISE FOR

MAXIMUM GAIN)

MAX

RADIO

TEST POINTS

GND

AUDIO

RADIO INDICATOR

STATUS INDICATOR

RED = HOLD, GREEN = DECODE

POWER AND

DATA TERMINALS

OPTION

DIPSWITCHES

INPUT

VOLTAGE

JUMPER

PROGRAM

BUTTON

PLACE VOLTAGE INPUT JUMPER

IN THIS POSITION TO SELECT A

REGULATED 5 VOLT DC INPUT

FROM THE ACCESS CONTROL

PANEL

PLACE VOLTAGE INPUT JUMPER

IN THIS POSITION TO SELECT A

8-24 VOLT DC INPUT FROM THE

ACCESS CONTROL PANEL

SELECT THE WIEGAND OUTPUT FORMAT

THAT MATCHES THE ACCESS CONTROL

SYSTEM BEING USED

SWITCH 1 26-BIT

SWITCH 2 30-BIT

SWITCH 3 31-BIT

RECEIVER OPTIONS

WIEGAND OUTPUT FORMAT

SWITCH 1 - LOCKOUT DISABLE

SWITCH 2 - HOLD ENABLE

SWITCH 3 - BUTTON OFFSET ENABLE

OFF

- (FACTORY SETTING) CAUSES RECEIVER TO IGNORE TRANSMITTER SIGNALS FOR ONE SECOND AFTER A VALIDATED TRANSMISSION.

- ALLOWS RECEIVER TO PASS WIEGAND DATA INSTANTLY WITH EACH VALIDATED TRANSMISSION.

OFF

- (FACTORY SETTING) HOLD INPUT SIGNALS ARE IGNORED.

- WHEN HOLD INPUT IS ACTIVE, ANY WIEGAND DATA WILL BE HELD FOR A MAXIMUM OF ONE SECOND THEN DISCARDED UNLESS THE

HOLD INPUT IS RELEASED DURING THE ONE SECOND TIME.

OFF

- (FACTORY SETTING) TRANSMITTERS PASS THEIR ID NUMBER TO THE WIEGAND OUTPUT WITHOUT ANY CHANGES.

- THE TRANSMITTER ID IS OFFSET TO THE RANGE ABOVE, BASED ON WHICH BUTTON IS PRESSED.

BUTTON OFFSET TABLE

LEFT

RIGHT

TOP

BOTTOM LEFT OR RIGHT

16384 32768 49152

= S W I T C H O N

SET XMTR FACILITY CODE

SWITCHES TO MATCH THE FACILITY

CODE PRE-PROGRAMMED INTO

TRANSMITTER BLOCK

NOTE: THE FACTORY SETTINGS

OF FACILITY CODE "0" WILL

ALLOW VALIDATION OF ANY

TRANSMITTER FACILITY CODE

S W T 0

S W T 1

S W T 2

S W T 3

1 0

1 1

1 2

1 3

1 4

1 5

TRANSMITTER BLOCK

FACILITY CODE 0-15

(ASSIGNED WHEN

TRANSMITTER BLOCK IS

ORDERED FROM LINEAR)

= S W I T C H O F F

XMTR FACILITY

CODE SWITCHES

BOTH

FUNCTION

AS LEFT

BUTTON

LEFT

BUTTON

RIGHT

BUTTON

TOP

BUTTON

TOP

BUTTON

LEFT

BUTTON

RIGHT

BUTTON

BOTTOM-RIGHT

BUTTON

BOTTOM-LEFT

BUTTON

LEFT

BUTTON

LEFT

BUTTON

RIGHT

BUTTON

OPERATE

AS TOP

BUTTON

THE FACTORY SETTING ALLOWS ALL

TRANSMITTER BUTTONS TO OPERATE

SET XMTR BUTTON DISABLE SWITCH(ES) ON TO

PREVENT SELECTED TRANSMITTER BUTTONS

FROM OPERATING

SWITCH 4 - TOP

SWITCH 5 - BOTTOM RIGHT

SWITCH 6 - BOTTOM LEFT

SWITCH 7 - RIGHT OR TOP RIGHT

SWITCH 8 - LEFT OR TOP LEFT

INSTR,INST,WOR

Linear P/N: 212902 C

Material: 20 Lb. Mead Bond

Size: 8.500" x 11.000"

Ink: Black

Side 2 of 2

Scale: 1-1

7. SET OUTPUT FACILITY CODE

8. CONNECT TERMINALS 9. CONNECT ANTENNA

10. PROGRAM AND TEST SYSTEM LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date

is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s

normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling

dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear Corporation

for consequential damages arising out of or in connection with use or performance of this product or other indirect damages

with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties,

including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as

labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied.

All products returned for warranty service require a Return Product Authorization Number (RPA#).

Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need in portable wireless signalling. However, there

are some limitations which must be observed.

✶ For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such,

they have limited transmitter power and therefore limited range.

✶ A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or

near their operating frequencies, regardless of code settings.

✶ Changes or modifications to the device may void FCC compliance.

✶ Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

✶ A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these

facts should be communicated to the ultimate users.

OUTPUT FACILITY CODE 0

WILL PASS THROUGH THE

TRANSMITTER FACILITY CODE

SWITCH SETTINGS FOR OUTPUT FACILITY CODES 0-255

SWT 0

SWT 1

SWT 2

SWT 3

SWT 4

SWT 5

SWT 6

SWT 7

SWT 8

SWT 9

SWT 10

SWT 11

SWT 12

SWT 13

SWT 14

SWT 15

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

SWT 0

SWT 1

SWT 2

SWT 3

SWT 4

SWT 5

SWT 6

SWT 7

SWT 8

SWT 9

SWT 10

SWT 11

SWT 12

SWT 13

SWT 14

SWT 15

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

255

SWT 0

SWT 1

SWT 2

SWT 3

SWT 4

SWT 5

SWT 6

SWT 7

SWT 8

SWT 9

SWT 10

SWT 11

SWT 12

SWT 13

SWT 14

SWT 15

SWT 0

SWT 1

SWT 2

SWT 3

SWT 4

SWT 5

SWT 6

SWT 7

SWT 8

SWT 9

SWT 10

SWT 11

SWT 12

SWT 13

SWT 14

SWT 15

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

= SWITCH OFF = SWITCH ON

OMNI-DIRECTIONAL

EXA-1000 ANTENNA

MOUNTED ON POLE

LOCAL WHIP

ANTENNA

(SUPPLIED)

CONNECTED

DIRECTLY TO

RECEIVER

DIRECTIONAL

EXA-2000 ANTENNA

MOUNTED ON POST

CHOOSE AN ANTENNA TO FIT THE INSTALLATION REQUIREMENTS

FOLLOW EXA ANTENNA

INSTRUCTIONS WHEN

CONSTRUCTING ANTENNA

SCREW CONNECTOR

ONTO RECEIVER

INDICATOR

VIEWING

WINDOW

ROUTE WIRE THROUGH

STRAIN RELIEF BEFORE

WIRING TO TERMINALS

(TIGHTEN LATER)

POWER AND

DATA TERMINALS

PWR (RED)

GND (BLK)

DAT1 (WHT)

DATO (GRN)

HOLD (BLU)

N/C

POWER

DATA

HOLD (OPTIONAL)

TO ACCESS

CONTROL

SYSTEM

WITH POWER APPLIED

TO THE RECEIVER,

PRESS AND RELEASE

THE PROGRAM BUTTON

TEST TRANSMITTERS FROM VARIOUS

LOCATIONS TO DETERMINE RADIO

RANGE

ADJUST THE RECEIVER'S

INTERNAL RADIO RANGE KNOB

TO LIMIT RADIO RECEPTION IF

REQUIRED

RECEPTION PATTERN WILL VARY

DEPENDING ON ANTENNA USED

AND SURROUNDING STRUCTURES

RADIO INDICATOR WILL

FLICKER AS SIGNAL IS

RECEIVED

STATUS INDICATOR LIGHTS

GREEN WHEN SENDING

WIEGAND DATA AND DURING

RECEIVER LOCKOUT

OPERATION, LIGHTS RED

WHEN HOLD INPUT IS

ACTIVE

Nortek Contol WOR User manual

Brand: Nortek Contol

Model: WOR

Type: User manual

This manual is also suitable for

Download PDF

report

Nortek Contol WOR User manual

This manual is also suitable for

Nortek Contol WOR User manual

Related papers

Other documents