Eiki LC-WGC500 Owner's manual

Category
Projectors
Type
Owner's manual

This manual is also suitable for

LINK
ACT
WGC500 Series
PjNET-50
Pj-to NetDirector
Network Capture 3
Network Viewer 3
Network Communication
OWNER'S MANUAL
2
Compliance
Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular instal-
lation. If this equipment causes harmful interference to radio or television reception which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC
Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in
the instructions. If such changes or modifications should be made, you could be required
to stop operation of the equipment.
Model Numbers : PjNET-50
Trade Name : EIKI
Responsible party : EIKI International, Inc.
Address : 30251 Esperanza Rancho Santa Margarita CA 92688-2132
Telephone No. : 800-242-3454 (949-457-0200)
3
Pj-to NetDirector
OWNER'S MANUAL [WGC500 Series]
ENGLISH
Compliance and Caution
CAUTION ON USE IN NETWORK
- When you receive an alert e-mail from the projector, you must check the projector
immediately. Fire or accident may result if the projector is used in an abnormal
condition.
- When you install the projector at remote location and use it through the network, you
must perform the safety inspections periodically. In this case you must pay attention to
the change of environment in which you installed the projector. It may cause fire or an
accident depending on the change of environment.
The CE Mark is a Directive conformity mark of the European Community (EC).
NOTES ON Lithium Battery (CALIFORNIA USA ONLY)
This product uses a Lithium Battery which contains Perchlorate Material - special han-
dling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
Notas acerca de pilas de litio (SOLO PARA CALIFORNIA, EE.UU.)
Este producto usa una pila de litio que contiene el material perclorato – puede ser nece-
sario una manipulación especial.
Consulte la página www.dtsc.ca.gov/hazardouswaste/perchlorate
CAUTION
Eiki International, Inc. assumes no responsibility for the loss or damage of data or dam-
age of the computer caused by using this product.
4
Compliance ..........................................................................................................................................................................2
Federal Communication Commission Notice.......................................................................................2
Chapter 1 Preparation ................................................................................................7
Features...................................................................................................................................................................................8
Operating environment of Pj-to NetDirector ...............................................................................................11
Before use ...........................................................................................................................................................................12
Chapter 2 Installation...............................................................................................15
Flow of installation ........................................................................................................................................................16
[1] Name and function of each part................................................................................................................... 17
[2] Installation and network configuration ....................................................................................................18
Mounting .................................................................................................................................................................. 18
Connection of LAN cable ............................................................................................................................... 19
Network configuration .....................................................................................................................................20
Network PIN code setting ..............................................................................................................................22
How to enter the numbers with the remote control 10-key buttons ................................23
Notice about system construction ...........................................................................................................24
[3] Installing the software .........................................................................................................................................25
Network Viewer & Capture 3 installation ..............................................................................................25
File Converter 2 Installation ...........................................................................................................................27
Chapter 3 Basic Setting and Operation ............................................................. 29
Login the setting page of the projector .........................................................................................................30
1 Enter the IP address ........................................................................................................................................30
2 Select a display mode and login ............................................................................................................30
3 Display of main setting page....................................................................................................................31
How to use the setting page .................................................................................................................................32
Initial setting .....................................................................................................................................................................34
Network PIN code setting ..............................................................................................................................35
PJLink and password setting .........................................................................................................................35
Date and time setting .......................................................................................................................................36
Network configuration ...............................................................................................................................................37
E-mail setting ...................................................................................................................................................................38
Examples: Type and contents of alert mail ..........................................................................................40
SNMP setting ....................................................................................................................................................................42
Chapter 4 Controlling the Projector ................................................................... 45
Power control and status check ...........................................................................................................................46
Controls ................................................................................................................................................................................48
Input .............................................................................................................................................................................48
System .........................................................................................................................................................................49
Image adjustment ..............................................................................................................................................50
Sound .........................................................................................................................................................................51
Menu ........................................................................................................................................................................... 51
PC adjustment .................................................................................................................................................................52
Setting up the projector ...........................................................................................................................................53
Save the controls and settings ..............................................................................................................................56
Store/free the settings ......................................................................................................................................56
Check the saved items ......................................................................................................................................57
Load a control set ................................................................................................................................................57
Timer setting ....................................................................................................................................................................58
How to set the timer ..........................................................................................................................................58
Check the timer events ....................................................................................................................................59
Change the event mode .................................................................................................................................59
Projector information .................................................................................................................................................. 61
Multi-control .....................................................................................................................................................................63
Controlling and setting the multi-projectors.....................................................................................63
Contents
5
Pj-to NetDirector
OWNER'S MANUAL [WGC500 Series]
ENGLISH
Contents
Start/stop the multi control ...........................................................................................................................64
Register the projector .......................................................................................................................................65
Confirmation of registered projector ......................................................................................................65
Change the mode of the registered projector .................................................................................66
Status ...........................................................................................................................................................................66
Check & Change page in the light mode .............................................................................................67
Controlling all together ....................................................................................................................................67
Setting all together .............................................................................................................................................67
Viewer auto setting all together .................................................................................................................68
Chapter 5 Network Capture...................................................................................69
About Network Capture function .......................................................................................................................70
Launching the Network Capture 3 ...........................................................................................................70
Commands on the task bar ...........................................................................................................................70
Parameter set up ..................................................................................................................................................71
Using the Real Time Capture ..................................................................................................................................72
Registering the computers ............................................................................................................................72
[1] Control by the computer ..........................................................................................................................73
[2] Control by the web browser ..................................................................................................................74
[3] Control by the projector ...........................................................................................................................75
Advanced using example ...............................................................................................................................76
Using the Network Communication .................................................................................................................77
Settings before using the Network Communication....................................................................78
Description of capture editing window ................................................................................................79
How to use the Network Communication ....................................................................................................81
Start the communication ................................................................................................................................81
Join the communication (only for Sub PC) ..........................................................................................81
Exit from the communication (only for Sub PC) ..............................................................................81
End the communication..................................................................................................................................81
Acquire and release of editing authority ..............................................................................................81
Edit capture image ..............................................................................................................................................82
Network Communication operation and change of state .................................................................84
Executing the forcing mode ..................................................................................................................................85
Error information ............................................................................................................................................................86
Chapter 6 Network Viewer ..................................................................................... 87
Creating the available data [Network Viewer 3] .........................................................................................88
[1] How to use the Network Viewer 3 (File Converter 1)..............................................................88
[2] How to use the Network Viewer 3 (File Converter 2) .............................................................92
Creating a program file [Program Editor] .......................................................................................................93
Procedure of making program ....................................................................................................................93
Setting up the display order and time of the images ...................................................................95
Using the Network Viewer function ..................................................................................................................98
[1] Control by the web browser ..................................................................................................................98
[2] Control by the projector .........................................................................................................................102
Chapter 7 Appendix ..............................................................................................105
Examples of connection ........................................................................................................................................ 106
Web browser setting ................................................................................................................................................ 108
Examples: OS/Browsers ..........................................................................................................................................109
Product specification ................................................................................................................................................113
Port specification .........................................................................................................................................................114
Q&A ......................................................................................................................................................................................115
6
Pj-to NetDirector
OWNER'S MANUAL [WGC500 Series]
ENGLISH
Pj-to NetDirector
OWNER'S MANUAL [WGC500 Series]
7
ENGLISH
1
Chapter 1
Preparation
Describes features and operating environment of this product.
8
Chapter 1 Preparation
Real Time Capture function (+p.72)
To display the screen image of
the computer by the projec-
tor through the network in real
time.
Features
Network Viewer function (+p.88)
To acquire the JPEG image data
from the file servers placed in
the network and project them
by the projector.
PC4PC3 PC6
Capture
PC5
PC1 PC2
PC4PC3 PC6
PC5
PC1 PC2
FTP file server
JPEG
Prog.
JPEG
PJ2
PJ1
Network Communication function (+p.77)
To communicate by sharing the
captured image of a computer
with multiple computers and
a projector. User can draw the
text and figure on the captured
image by using a drawing tool.
PC2
PC6
Capture
PC5
PC1
PJ1
Capture a screen
image of PC5 and
make marking with
a tool.
9
Pj-to NetDirector
OWNER'S MANUAL [WGC500 Series]
ENGLISH
E-Mail Alert function (+p.38)
The projector (Network Unit)
sends messages to the regis-
tered e-mail addresses when
a lamp abnormality or power
failure occurs with the projec-
tor. This message describes
how to solve the cause of the
problems. You can take efficient
action for quick recovery.
PC4PC3 PC6
PC5
PC1 PC2
Y o u’ve got
Mail.
PJ2
PJ1
Web Management function (+p.46)
With this function, you can
monitor projector functions
such as power status, lamp
status, input mode, signal
condition, lamp-use time, etc.
through the network by using
the web browser installed on
your computer.
PC4PC3 PC6
PC5
PC1 PC2
Turn ON PJ 2
PJ2
PJ1
Features
SNMP Agent function (+p.42)
To send the information of
the projector to the SNMP
manager. Enables you to
manage the projector con-
dition with the supplied
SNMP manager software.
PJ1
PC6
PC4
PJ2 PJ3 PJ4
PC5
You received
a Tr ap.
SNMP Manager
Trap
Trap
10
Chapter 1 Preparation
Multi-control function (+p.63)
A single computer can control and set up the multiple projectors at the same time.
PJ1
PC6
PC4
PC5
Select Input2 for
PJ 1 to PJ4.
PJ2 PJ3 PJ4
Automatic On/Off using Clock function (+p.58)
Automatically turn on or off the
projectors at specified date/day
and time by using the clock func-
tion.
Now it’s 11:30
I am ready to turn ON,
and select Input 3 (Video)
SNMP Manager function (refer to the separated booklet)
A function to manage the
condition of projectors in
the network by using the
SNMP protocol. The man-
aging computer needs to
provide an SNMP manag-
ing software. Refer to the
owner's manual of the "PJ
Network Manager" sup-
plied separately for further
details.
PJ1
PC6
PC4
PJ2 PJ3 PJ4
PC5
You received
a Tr ap.
SNMP Manager
Trap
Trap
11
Pj-to NetDirector
OWNER'S MANUAL [WGC500 Series]
ENGLISH
Standard mode
Operating System
Windows 98, Windows Me, Windows NT4.0SP6
Windows 2000, Windows XP, Windows Vista (32bit version)
Computer environment
Recommended CPU
Higher than Pentium III 900MHz
Memory
64MB (Minimum)/ 128MB or more(Recommended)
128MB or more for Windows XP
1GB or more for Windows Vista
HDD free area
100MB or more
Drive equipment
CD-ROM drive
Display setting of
computer
Support one of following resolutions;
VGA (640 x 480), SVGA(800 x 600), XGA(1,024 x 768) Number of col-
ors: Either of 16 bit (65,536 color 24/32 bit (16.77 million colors))
Network card
The computer must provide a 10Base-T or 100Base-TX network
card.
Web Browser*
Internet Explorer version 5.0, 5.5 or 6.0
Netscape Navigator version 6.2, 7.0 or 7.1
* Used to control and set up the projector. The layout of pages in
the browser may slightly differ from each type of application or
operating system you use.
Plug-Ins
Adobe Flash Player version 6,0,79,0(6.0r79) or later
Internet Mailer*
- Microsoft Outlook - Microsoft Outlook Express
- Netscape Mail
* Required the internet e-mail application software to receive an
e-mail alert sent from this product. If you do not use the function
E-mail Alert, this application is not required.
FTP Service *
- FTP server (Windows 2000 Professional or Windows XP
Professional)
* The FTP service provided with the Windows 2000 Professional
or Windows XP Professional is required when using the Network
Viewer function.
Operating environment of Pj-to NetDirector
To perform the managing and setting of the projector by using this product, the environ-
ment described below is required.
*1 The "Light Mode" and "Standard Mode" will be explained on item "Display Mode" (+ p.30-32)
Operating Environment
PDA restriction
The PDA can be used for the Light mode*
1
only. The operating system of the PDA is
PocketPC2002 or higher. The version of the
Adobe
Flash Player is 6,0,81,0 or higher.
12
Chapter 1 Preparation
The limitation
*1
of connection between this product and hub or computer
Suitable LAN cables are limited by length and type as follows;
Connection Type of usable LAN cable Maximum length
Network Unit - Hub UTP Straight Cable with category 3 or 5 *
2
100m
Network Unit - Computer UTP Cross Cable with category 3 or 5*
2
100m
*1 There may be other limitations depending on your network environment or LAN specification.
Please consult your network administrator for further details.
*2 Category of LAN cable indicates the cable quality. Normally, a cable with category 3 or 5 is used
for 10Base-T network, and a cable with category 5 is used for 100Base-TX network.
Before use
Package contains
The package contains following items. Check each item as you unpack the package. If you
have any of the following items missing, contact the sales dealer.
LINK
ACT
Network unit 1 piece
Software CD-ROM 1 piece
Network Viewer & Capture 3 software
PJ Network Manager software
Quick Setup Guide 1 piece
English/Japanese
Document CD-ROM 1 piece
Pj-to NetDirector Owner's Manual
PJ Network Manager Owner's manual
Quick Setup
Guide
13
Pj-to NetDirector
OWNER'S MANUAL [WGC500 Series]
ENGLISH
Notice
Expression/Abbreviation
The word "projector" found in this manual means "projector provided with Network unit"
unless otherwise noted.
The OS of the computer and the Web browser described in this manual is Windows XP
Professional and Internet Explorer 6.0. In case of another OS or Web browser, some instruc-
tion procedures may differ from the actual operation depending on your computer envi-
ronment.
Use of this manual
This manual does not provide the description of basic operation and functions for com-
puter, web browser, projector and network. For instructions about each piece of equip-
ment or application software, please refer to the respective booklet.
Trademarks
Ethernet is a registered trademark of Xerox Corporation. Microsoft, Windows, Windows
NT, Windows XP and Windows Vista are registered trademarks of Microsoft Corporation.
Internet Explorer is a registered trademark of Microsoft Corporation. Netscape Navigator
and Netscape Communicator are trademarks or registered trademarks of Netscape
Communications Corporation. JavaScript is a registered trademark of Sun Microsystems,
Inc. PJLink is a registered trademark of JBMIA (Japan Business Machine and Information
System Industries Association).
Other product or brand names in this manual are registered trademarks or trademarks of
their respective owners.
* Unauthorized use of a part or whole of the contents in this manual is prohibited.
* The contents of this manual are subject to change without notice.
Before use
14
Chapter 1 Preparation
Pj-to NetDirector
OWNER'S MANUAL [WGC500 Series]
ENGLISH
Pj-to NetDirector
OWNER'S MANUAL [WGC500 Series]
15
ENGLISH
Chapter 2
Installation
2
Describes how to install the network unit and software, and config-
ure the network.
16
Chapter 2 Installation
The following are instructions for attaching this product to the projector and connecting it
to the network. Please review the entire procedure to become familiar with it.
Function of the network unit (+ p.17)
1
Installation and network configuration (+ p.18-24)
2
Installation of the software (+ p.25-27)
3
Set up is complete
1 Mount this product onto the projector.
2 Connect the LAN cable and join it to the network.
3 Configure the network of the network unit.
4 Set the Network PIN code.
Explains how to install the software Network Viewer & Capture 3 into your com-
puter.
Flow of installation
The preparation is completed to control the projector connected to the network. At next
step, set up and control the projector via the network by using the web browser installed
on your computer. Please see chapter 3 "Basic setting and operation". (+ p.29)
Explains the name and functions of each part of the network unit.
17
Pj-to NetDirector
OWNER'S MANUAL [WGC500 Series]
ENGLISH
Name and function of each part
[1] Name and function of each part
POWER indicator
This lights up red when the network
function is set ON in the projector
menu.
LAN port
Connecting the LAN cable. (+ p.19)
Connector plug
Connecting to the terminal on the pro-
jector. (+ p.18)
Mounting screws
Mount by using a coin etc. (+ p.18)
LINK indicator
This lights up red when the network unit is
connected to the network correctly.
ACT indicator
This turns on and off with green when
sending or receiving of data
(Top View)
(Bottom View)
18
Chapter 2 Installation
AC cord must be disconnected when mounting or removing this product otherwise it may dam-
age the product.
Do not install multiple network units into a projector otherwise it may damage the product.
Connect the AC cord after connecting the LAN cable and computer.
Caution
!
Mounting
[2] Installation and network configuration
1 Disconnect the AC plug from the projector.
2 Remove the connector cover and screw
covers (2 pieces) from the projector and
insert plug on this product to the option
connector.
3 Tighten two screws by using a coin etc.
Connector cover
Screw cover
19
Pj-to NetDirector
OWNER'S MANUAL [WGC500 Series]
ENGLISH
Connection of LAN cable
To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) straight cable
with RJ-45 plug. There are two different types of cables depending on whether the network is
constructed with 10Base-T or 100Base-TX. Prepare the Hub (10Base-T or 100Base-TX) to distrib-
ute the network cable if required.
Use the UTP cross cable when you connect the computer and projector directly not using the
hub.
When you connect the projector into the 10Base-T network, use cable with category 3 or 5. When
you connect the projector into the 100Base-TX network, use cable with category 5.
The length of cable between hub and projector should be less than 100m.
Installation and network configuration
1 Disconnect the AC plug from the projector.
2 Connect the UTP straight cable to the LAN
port on the network unit.
3 Connect the UTP straight cable to the hub.
Hub
(10Base-T, 100Base-TX)
UTP straight cable
20
Chapter 2 Installation
1 Selection of network menu
Turn on the projector and display the menu on the screen. Select network icon from the
main menu and then press SELECT button once. Check that the mode is "On". If not,
change mode to "On" using the point buttons (7 8).
Network configuration
Confirmation of the network menu
When installing this product to the projector, the network on-screen menu items for this
product are activated automatically. If not activated, the product may not have been
installed correctly. Please check item "Mounting" (+ p.18).
Configure the network
Before performing the network configuration, prepare network address numbers (IP
Address, Subnet Mask, Default Gateway, DNS) assigned to the projector. Ask your network
administrator for the network address.
For example, the case where the following network address is set up is explained.
IP Address : 192.168.1.201
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
DNS : 0.0.0.0
The default network configuration is set as follows.
IP Address : 192.168.0.2
Subnet Mask : 255.255.255.0
Default Gateway : 0.0.0.0
DNS : 0.0.0.0
Network icon
Select "On" or "Off"
with 7 8 button
The network unit begins restarting each time the mode is set "On".
Change the mode to "On" then the "Please wait..." message will appear and after completing the
operation, the message will disappear.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124

Eiki LC-WGC500 Owner's manual

Category
Projectors
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI