VOLTCRAFT BS-25HR Operating Instructions Manual

Page is loading ...

OPERATING INSTRUCTIONS

VERSION 05/14

BS-25HR ENDOSCOPE

ITEM NO.: 1086332

INTENDED USE

The endoscope is a visual aid for troubleshooting or inspection of voltage-free systems and

installations. The camera image is displayed on the built-in monitor. The light on the camera

head can be adjusted. The permanently installed gooseneck camera is waterproof (IP67)

and suited for use in watery liquids (no acidic or basic solutions). The main unit may not be

exposed to or submerged in moisture. Power supply is via four AA batteries (not included).

Operationinpotentiallyexplosiveareasand/oruseonpersonsoranimalsisnotpermitted.

For safety and approval purposes (CE), you must not rebuild and/or modify this product. If

you use the product for purposes other than those described above, the product may be

damaged.Inaddition,improperusecancausehazardssuchasshortcircuiting,re,electric

shock etc. Read the instructions carefully and keep them. Make this product available to third

parties only together with its operating instructions.

This product complies with the statutory national and European requirements. All company

DELIVERY CONTENT

• Endoscope

• 3 x attachments (magnet, hook, mirror)

• Storage case

• Operatinginstructions

SAFETY INSTRUCTIONS

Read the operating instructions carefully and especially observe the safety

information. If you do not follow the safety instructions and information

on proper handling in this manual, we assume no liability for any resulting

personal injury or damage to property. Such cases will invalidate the

warranty/guarantee.

a) Persons / Product

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. These may become

dangerous playing material for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity,moisture,ammablegases,vapoursandsolvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed if

the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height

can damage the product.

• The main unit is not waterproof and may therefore not be used under water.

• The endoscope is suited for inspection only in voltage-free systems. The camera

head is made of metal and can cause short-circuiting.

• For safety reasons, make sure all system components are voltage-free before

inspection.

• Always store the endoscope and all accessories in the case for periods of disuse.

Sensitive surfaces (with furniture polish, etc.) may react chemically when exposed

to the housing.

• Never use the product immediately after it has been brought from a cold room into

a warm one. The condensation generated could destroy the product. Always allow

the product to reach room temperature before use. This may take several hours.

• The use of electrical devices must be supervised by trained staff in schools,

training centers, hobby and do-it-yourself workshops.

• In industrial facilities, heed all applicable accident prevention regulations for

electrical installations and equipment.

b) Batteries / Rechargeable batteries

• Correct polarity must be observed while inserting the batteries.

• Batteries should be removed from the device if it is not used for a long period of

time to avoid damage through leaking. Leaking or damaged batteries might cause

acid burns when in contact with skin, therefore use suitable protective gloves to

handle corrupted batteries.

• Batteries must be kept out of reach of children. Do not leave the battery lying

around, as there is risk, that children or pets swallow it.

• All the batteries should be replaced at the same time. Mixing old and new

batteries in the device can lead to battery leakage and device damage.

• Batteriesmustnotbedismantled,short-circuitedorthrownintore.Never

recharge non-rechargeable batteries. There is a risk of explosion.

c) Miscellaneous

• Consult an expert when in doubt about operation, safety or connection of the

device.

• Maintenance,modicationsandrepairsaretobeperformedexclusivelybyan

expertorataqualiedshop.

If you are not sure about the correct connection or use, or if questions arise which are not

covered by these operating instructions, please do not hesitate to contact our technical

supportoranotherqualiedspecialist.

OPERATING ELEMENTS

7 8 9

1 Goose neck

2 Camera head

3 Monitor

4 ↓button

5 (on/off) button

6 ↑button

7 Mirror attachment

8 Magnet attachment

9 Hook attachment

Legal notice

These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

Allrightsincludingtranslationreserved.Reproductionbyanymethod,e.g.photocopy,microlming,orthecaptureinelectronicdataprocessing

systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.

These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.

INSERTING / REPLACING BATTERIES

1. Remove the battery compartment cover from the back of the device.

2. Insert four AA batteries into the battery compartment, observing correct polarity. Heed

correct polarity as indicated in the battery compartment.

3. Close the battery compartment.

Change the batteries as soon as the battery symbol appears at the top right of the

monitor (3) or if the product no longer turns on.

OPERATION

Hold the camera neck and head only in voltage-free liquids. Do not submerge

the camera neck past the marking “MAX Water Level”.

The endoscope is suited for inspection only in voltage-free systems.

The camera head is made of metal and can cause short-circuiting. For

safety reasons, make sure all system components are voltage-free before

inspection.

Avoid heavy mechanical loads and/or vibrations. Do not exceed the minimum

bending radius of 45 mm.

a) Turning on/off

• Press the button (5) to turn on the product. The camera image is shown on the

monitor (3).

• Press the button again to turn off the product. The monitor goes out.

b) Camera light

Attention, LED light:

• Do not look directly into the LED light!

• Do not look into the beam directly or with optical instruments!

• Four white LEDs with 6 adjustable lighting levels are built into the camera head (2).

• Repeatedlypressthe↑button(6)toincreasetheLEDlightinglevel.

• Repeatedlypressthe↓button(4)todecreasetheLEDlightinglevelortoturnoffthelight.

• While adjusting the lighting level, a bar graph appears at the bottom middle of the

monitor (3) to indicate the set lighting level.

Set the light so that the image is neither over- nor underexposed.

c) Monitor backlight

• Simultaneouslypressandholdthe↑(6)und↓(4)buttonstoadjustthemonitor(3)backlight

in 3 levels.

• Release both buttons when the desired level is reached.

d) Zoom

• Theimagecanbemagniedin2levels:

- 1.5xmagnication

- 2xmagnication

• Pressandholdthe↓(4)button.Themonitor(3)showsoneofthreeindicators:

- 1.5x (1.5x magnification)

- 2.0x (2x magnification)

- 1.0x(nomagnication)

e) Rotating the image

Pressandholdthe↑(6)buttontorotatetheimage180°.

f) Attachments

• Carefully open the attachment’s fastening ring. Fasten the attachment to the narrow

indentation beneath the camera head. Do not bend the fastening ring too much to open it to

prevent it from breaking.

• Makesurethattheattachment’sfasteningringisclosedbeforeuse.Otherwiseyourunthe

risk of losing the attachment.

• Themirrorattachment(7)canextendtheendoscope’seldofviewintoareasthatare

difculttoaccessforthecamerahead.

• The magnet attachment (8) can be used to locate lost metallic objects.

• The hook attachment (9) can be used to take hold of small objects.

MAINTENANCE AND CLEANING

• Besides occasional cleaning, the device is maintenance-free. To clean the device, use a

soft, anti-static and lint-free cloth.

• Do not use any abrasive or chemical cleaners.

• After use in liquids, always thoroughly rinse the camera neck with clean water and dry

before storing the product in the case.

• To clean the camera lens, use a small brush or cotton swabs.

DISPOSAL

a) Product

Electronic devices are recyclable waste and must not be disposed of in the

household waste.

At the end of its service life, dispose of the product according to the relevant

statutory regulations.

Remove any inserted (rechargeable) batteries and dispose of them separately from

the product.

b) (Rechargeable) batteries

Youastheenduserarerequiredbylaw(BatteryOrdinance)toreturnallusedbatteries/

rechargeable batteries. Disposing of them in the household waste is prohibited.

Contaminated (rechargeable) batteries are labelled with this symbol to indicate that

disposal in the domestic waste is forbidden. The designations for the heavy metals

involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable)

batteries, e.g. below the trash icon on the left).

Used (rechargeable) batteries can be returned to collection points in your

municipality, our stores or wherever (rechargeable) batteries are sold.

Youthusfullyourstatutoryobligationsandcontributetotheprotectionoftheenvironment.

TECHNICAL DATA

Power supply ................................ 4 x 1.5 V battery type AA (not included)

Monitor ..........................................5.8 cm (2.3”) TFT

Resolution .....................................960 x 240 pixels (monitor)

640 x 480 pixels (camera)

Camera light .................................4 white LEDs

White balance ...............................automatic

Exposure ......................................automatic

Field of view ..................................54º

Focus depth ..................................≥3cm

Operatingconditions .....................0to+45ºC,15–85%RH

Storage conditions ........................-10to+50ºC,15–85%RH

Bending radius ..............................min. 45 mm

Gooseneck length .........................88 cm ±2 cm

Gooseneck Ø ................................6.5 mm

Camera head Ø ............................ 8 mm

Dimensions (W x H x D) ...............86 x 1105 x 60 mm

Weight ..........................................approx. 313 g

Page is loading ...

VOLTCRAFT BS-25HR Operating Instructions Manual

Related papers

Other documents