Page is loading ...
Please read these instructions before operating the product
www.StanleyTools.com
Machine Control Receiver
with Remote Display
GB
NL
GR
I
FIN
HU
BG
LV
D
DK
CZ
E
NO
SK
RO
LT
F
SE
RU
PT
PL
SI
EE
TR
HR
79003492
FMHT1-77360
User Manual
GB
2
Contents
• Safety
• Power & Recharging
• Description
• Equipment Setup
• Mounting Receiver
• Using the Receiver
• Using the Remote Display
• Operation
• Using the menu to change settings
• Troubleshooting
• Radio frequency interference
•
• Warranty
User Safety
for that particular instrument)
WARNING!
Carefully read the Safety Instructions and Product
Manual before using this product. The person
responsible for the instrument must ensure that all
users understand and adhere to these instructions.
CAUTION!
expose your eyes to the emitting laser beam (red light
time may be hazardous to your eyes. Retain all
sections of the manual for future reference.
WARNING!
magnets could disrupt normal operation of such devices.
The magnets could damage thinner metal surfaces; use caution when receiver is out of its carrying case.
CAUTION! Risk of injuries!
Level
Indicators
Magnetic
Mounts
Battery
Indicator
LED
Tilt
Indicator
Power Button
Battery recharging
port & cover
Level
Indicators
Plumb
Indicators
Suction
Lever
Suction Cup
Swivel Arm
Power Button
Remote Display
3
battery is low.
•
3. Connect power adapter to AC outlet
Battery indicator will light when the battery is low.
NOTE:
WARNING!
WARNING!
and covered place.
End of Life
DO NOT dispose of this product with household waste.
ALWAYS dispose of batteries per local code.
PLEASE RECYCLE in line with local provisions for the collection and disposal of electrical and electronic waste under
the WEEE Directive.
Declaration of Conformity
For further details please refer to www.stanleytools.com.
Description
accurate grade readings.
User Manual
GB
Equipment Setup
Extended
Excavation
Depth
L
L
A
)
Determine the distance from the height of the laser to the bottom of the excavation (L).
With Magnets
B
)
Optional Mounting: With Clamps
C
)
Coarse accuracy setting. (The last setting used is stored into memory and becomes the default setting.
Yellow
Yellow
Green
Red
Red
FineCoarse
Press and hold the Power button >3 seconds to turn off the unit.
Channel is 2nd LED.
Yellow
Yellow
Green
Red
Red
Channel
Accuracy
B
A
5
Yellow
Yellow
Green
Red
Red
Channel 2
Channel
Yellow
Yellow
Green
Red
Red
Coarse
Fine
Accuracy
Note:
Using the Remote display
Press the Power button momentarily to turn on the unit. The LEDs
plumb LEDs will remain lit.
Press and hold the Power button >3 seconds to turn off the unit.
remote display off.
when your menu choice is lit.
Accuracy Channel Receiver
LEDs off
Plumb
Indicator
off
the remote display will exit menu mode and the setting will be saved as default.
Accuracy
Fine Coarse
the remote display will exit menu mode and the setting will be saved as default.
Channel Channel 2
Note:
Note:
Receiver
LEDs
LEDs OFF
This would usually be done to conserve battery life in the receiver.
Yellow
Yellow
Green
Red
Red
User Manual
GB
saved until unit is turned off.
Plumb
LEDs
LEDs OFF
Operation
Grade Detection
Same for receiver and remote display
Receiver
too high
or lost
beam
Receiver
on grade
Receiver
too low
or lost
beam
9 Channels
(see dots)
7 Channels
(see dots)
Yellow
Yellow
Green
Red
Red
Remote Display
LED
Flashing
Green
LED
Solid
Green
LED
Flashing
Red
Out OutPlumb PlumbIn In
Red Green Red
• Receiver out of range
• Receiver turned off
Note: The remote and receiver must be in communication for the menu to be accessed on the remote.
L
L
7
Range:
Accuracy:
Actual accuracy and range depend on beam diameter and distance to the transmitter.
Reception height:
Reception angle:
IP Rating:
Receiver power:
Receiver Charging time:
Receiver battery life:
Remote display power:
Frequency range:
(Receiver to remote display)
Size
Receiver:
Remote Display:
Weight
Receiver:
Remote Display:
from date of purchase.
Stanley Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
UK
Subject to change without notice
www.stanleytools.com
/