COMPANION COMP478 Owner's manual

Brand: COMPANION

Model: COMP478

Type: Owner's manual

Distributed by

PRIMUS AUSTRALIA Pty Ltd

Bundoora Victoria 3083

www.primusaustralia.com.au

10 LITRE PRESSURE SHOWER

Instruction Manual

Part No. COMP478

THIS APPLIANCE

IS NOT INTENDED

FOR THE SUPPLY OF

DRINKING WATER.

THIS APPLIANCE IS

INTENDED FOR THE

SUPPLY OF HEATED

WATER FOR THE

PURPOSE OF WASHING

AND CLEANING ONLY.

CHECK AND

CONFIRM SAFE

WATER TEMPERATURE

BEFORE USING

THIS APPLIANCE.

WATER FROM THIS

APPLIANCE MAY BE

VERY HOT.

IMPORTANT

It is IMPORTANT that you

read these instructions

carefully and understand

the operation and safety

features of this appliance.

Keep these instructions

for future reference.

WARRANTY

This appliance is covered against

faulty workmanship and materials

for a period of 12 months from the

date of original purchase.

PARTS LIST

1. Hand pump

2. Pressure release valve

3. Thermometer

4. Hose

5. Shower head

6. Support base

7. Carry bag

STORAGE

IMPORTANT – DO NOT leave water in

cylinder or hose when storing.

• Ensure the cylinder is cold.

• Release air pressure and remove pump.

• Release hose and hold shower

head and depress lever to allow

water to drain from hose.

• Invert cylinder, drain water and replace pump.

DO NOT lock back in place.

• Wipe down all surfaces to remove dirt and

moisture before placing in storage bag.

COM1950_10L_shower_maual_ED5.indd 1-3 23/05/11 3:12 PM

IMPORTANT

• This appliance is designed for outdoor use only.

• Handle with care even after brief use, always pick

up using the handle not the cylinder.

• Use only in well ventilated areas.

• This appliance shall only be used in an above

ground open air situation with natural ventilation,

without stagnant areas, where gas leakage and

products of combustion are rapidly dispersed by

wind and natural convection.

• When using this appliance, children must be

supervised by an adult at all times.

• Never leave appliance unattended when operating.

• Do not attempt to move or relocate the appliance

when it is operating. Extinguish the burner and

allow to cool then move the appliance.

• When not in use, release air pressure from cylinder.

• Keep out of reach of children and pets at all times.

OUTDOOR USE ONLY

CAUTION: Accessible parts may be very hot.

Keep young children away.

TO OPERATE

1. Assemble support base on a solid, non-combustible

level surface in a well ventilated outdoor area.

Ensure area is clear of ﬂammable materials

and vapors. Position a suitable burner or

heat source underneath.

2. Remove hose and then the hand pump from

cylinder by turning handle counter-clockwise,

do not depress handle, then lift out.

3. IMPORTANT: Open the pressure relief valve and

check that it is locked in the open position.

4. Fill cylinder with cold water to the MAXIMUM

water mark located on the side of the cylinder.

5. Once ﬁlled, insert the hand pump back into

cylinder and turn handle clockwise to tighten.

6. Position the cylinder onto the heating

frame, checking that it is securely

located and the frame is stable.

7. IMPORTANT: Check that the pressure

release valve is still in the open

position before heating.

8. Heat water until desired temperature is

reached. Refer to thermometer on

cylinder for temperature reading.

IMPORTANT - Do not heat over maximum

temperature shown on the thermometer.

9. Remove the cylinder from the support base, take

care as the handle and cylinder may be hot.

10. Move cylinder from side to side to mix warmer water

at the top of the cylinder with cooler water that will

be closer to the bottom. Recheck thermometer to

ensure desired temperature is reached.

11. Attach the hose and shower head to the male outlet

on the cylinder, checking that there are no kinks in

the hose and then close the pressure relief valve.

12. Release the handle by depressing

slightly and turning anti-clockwise

until it is released and springs up.

13. Pull the handle up and commence

pressurising by pumping the

handle before locking the handle

back into position.

14. Hold shower head and depress the

trigger to start the water ﬂow.

IMPORTANT - Check water temperature before

use. If water temperature is too hot, gently release

the pressure relief valve and add cold water as

necessary or leave to cool. Swirl water in the cylinder

and check temperature reading again using

thermometer before use.

15. If all water is not used at once and will be

used again soon without reheating, ensure

that any remaining water is swirled in the

cylinder prior to use in order for thermometer

to show an accurate water temperature

reading. Check temperature again before use.

companionleisure.com.au

COM1950_10L_shower_maual_ED5.indd 4-6 23/05/11 3:12 PM

COMPANION COMP478 Owner's manual

COMPANION COMP478 Owner's manual

COMPANION COMP478 Owner's manual

Related papers

Other documents