Page is loading ...
Distributed by
PRIMUS AUSTRALIA Pty Ltd
Bundoora Victoria 3083
www.primusaustralia.com.au
10 LITRE PRESSURE SHOWER
Instruction Manual
Part No. COMP478
THIS APPLIANCE
IS NOT INTENDED
FOR THE SUPPLY OF
DRINKING WATER.
THIS APPLIANCE IS
INTENDED FOR THE
SUPPLY OF HEATED
WATER FOR THE
PURPOSE OF WASHING
AND CLEANING ONLY.
CHECK AND
CONFIRM SAFE
WATER TEMPERATURE
BEFORE USING
THIS APPLIANCE.
WATER FROM THIS
APPLIANCE MAY BE
VERY HOT.
IMPORTANT
It is IMPORTANT that you
read these instructions
carefully and understand
the operation and safety
features of this appliance.
Keep these instructions
for future reference.
WARRANTY
This appliance is covered against
faulty workmanship and materials
for a period of 12 months from the
date of original purchase.
PARTS LIST
1. Hand pump
2. Pressure release valve
3. Thermometer
4. Hose
5. Shower head
6. Support base
7. Carry bag
STORAGE
IMPORTANT – DO NOT leave water in
cylinder or hose when storing.
• Ensure the cylinder is cold.
• Release air pressure and remove pump.
• Release hose and hold shower
head and depress lever to allow
water to drain from hose.
• Invert cylinder, drain water and replace pump.
DO NOT lock back in place.
• Wipe down all surfaces to remove dirt and
moisture before placing in storage bag.
3
6
7
1
2
3
4
5
6
COM1950_10L_shower_maual_ED5.indd 1-3 23/05/11 3:12 PM
IMPORTANT
• This appliance is designed for outdoor use only.
• Handle with care even after brief use, always pick
up using the handle not the cylinder.
• Use only in well ventilated areas.
• This appliance shall only be used in an above
ground open air situation with natural ventilation,
without stagnant areas, where gas leakage and
products of combustion are rapidly dispersed by
wind and natural convection.
• When using this appliance, children must be
supervised by an adult at all times.
• Never leave appliance unattended when operating.
• Do not attempt to move or relocate the appliance
when it is operating. Extinguish the burner and
allow to cool then move the appliance.
• When not in use, release air pressure from cylinder.
• Keep out of reach of children and pets at all times.
OUTDOOR USE ONLY
CAUTION: Accessible parts may be very hot.
Keep young children away.
TO OPERATE
1. Assemble support base on a solid, non-combustible
level surface in a well ventilated outdoor area.
Ensure area is clear of flammable materials
and vapors. Position a suitable burner or
heat source underneath.
2. Remove hose and then the hand pump from
cylinder by turning handle counter-clockwise,
do not depress handle, then lift out.
3. IMPORTANT: Open the pressure relief valve and
check that it is locked in the open position.
4. Fill cylinder with cold water to the MAXIMUM
water mark located on the side of the cylinder.
5. Once filled, insert the hand pump back into
cylinder and turn handle clockwise to tighten.
6. Position the cylinder onto the heating
frame, checking that it is securely
located and the frame is stable.
7. IMPORTANT: Check that the pressure
release valve is still in the open
position before heating.
8. Heat water until desired temperature is
reached. Refer to thermometer on
cylinder for temperature reading.
IMPORTANT - Do not heat over maximum
temperature shown on the thermometer.
9. Remove the cylinder from the support base, take
care as the handle and cylinder may be hot.
10. Move cylinder from side to side to mix warmer water
at the top of the cylinder with cooler water that will
be closer to the bottom. Recheck thermometer to
ensure desired temperature is reached.
11. Attach the hose and shower head to the male outlet
on the cylinder, checking that there are no kinks in
the hose and then close the pressure relief valve.
12. Release the handle by depressing
slightly and turning anti-clockwise
until it is released and springs up.
13. Pull the handle up and commence
pressurising by pumping the
handle before locking the handle
back into position.
14. Hold shower head and depress the
trigger to start the water flow.
IMPORTANT - Check water temperature before
use. If water temperature is too hot, gently release
the pressure relief valve and add cold water as
necessary or leave to cool. Swirl water in the cylinder
and check temperature reading again using
thermometer before use.
15. If all water is not used at once and will be
used again soon without reheating, ensure
that any remaining water is swirled in the
cylinder prior to use in order for thermometer
to show an accurate water temperature
reading. Check temperature again before use.
companionleisure.com.au
COM1950_10L_shower_maual_ED5.indd 4-6 23/05/11 3:12 PM
/
