MULTIMEDIA PROJECTOR
MODEL LC-X71
LC-X71L (Lensless)
OWNER’S MANUAL
2
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNER’S MANUAL WITH
THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Before operating this projector, read this manual thoroughly
and operate the projector properly.
This projector provides many convenient features and
functions. Operating the projector properly enables you to
manage those features and maintain it in better condition for a
considerable time.
Improper operation may result in not only shortening the
product life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this
manual again, check operations and cable connections and try
the solutions in the “Troubleshooting” section in the end of this
booklet. If the problem still persists, contact the dealer where
you purchased the projector or the service center.
Safety Precaution
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
– This projector produces intense light from the projection
lens. Do not stare directly into the lens as much as
possible. Eye damage could result. Be especially careful
that children do not stare directly into the beam.
– Install the projector in a proper position. If not, it may result
in a fire hazard.
– Provide appropriate space on the top, sides and rear of the
projector cabinet for allowing air circulation and cooling the
projector. Minimum clearances must be maintained. If the
projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained. Do
not cover the ventilation slots on the projector. Heat build-
up can reduce the service life of your projector, and can
also be dangerous.
– If the projector is not to be used for an extended time,
unplug the projector from the power outlet.
CAUTION
Not for use in a computer room as defined in the Standard for
the Protection of Electronic Computer/Data Processing
Equipment, ANSI/NFPA 75.
Ne peut être utilisé dans une salle d’ordinateurs telle que
définie dans la norme ANSI/NFPA 75 Standard for Protection
of Electronic Computer/Data Processing Equipment.
CAUTION ON HANGING FROM THE CEILING
When hanging the projector from the ceiling,
clean the air intake vents, air filters, and top
of the projector periodically with a vacuum
cleaner. If you leave the projector unclean
for a long time, the dust will block the
operation of the cooling function, and it may
cause a breakdown or a disaster.
DO NOT SET THE PROJECTOR IN GREASY, WET, OR
SMOKY CONDITIONS SUCH AS IN A KITCHEN TO
PREVENT A BREAKDOWN OR A DISASTER. IF THE
PROJECTOR COMES IN CONTACT WITH OIL OR
CHEMICALS, IT MAY BECOME DETERIORATED.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER
USE.
TO THE OWNER
SIDE and TOP REAR
NOTE: This symbol and recycle system are applied only to EU countries
and not applied to the countries in the other area of the world.
Your EIKI product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from
your household waste.
Please dispose of this equipment at your local community
waste collection/recycling centre.
In the European Union there are separate collection
systems for used electrical and electronic products.
Please help us to conserve the environment we live in!
3
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not install the projector near the ventilation duct of air-
conditioning equipment.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
4
COMPLIANCE
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable
to insert the plug into the outlet, contact your electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
AC POWER CORD REQUIREMENT
Federal Communication Commission Notice
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
Model Numbers : LC-X71/LC-X71L
Trade Name : EIKI
Responsible party : EIKI International, Inc.
Address : 30251 Esperanza Rancho Santa Margarita CA 92688-2132, U.S.A.
Telephone No. : 800-242-3454 (949-457-0200)
5
TABLE OF CONTENTS
NAME OF EACH PART OF PROJECTOR 7
SETTING-UP PROJECTOR 8
CONNECTING AC POWER CORD 8
POSITIONING PROJECTOR 9
LENS INSTALLATION 9
ADJUSTABLE FEET 10
INSTALLING PROJECTOR IN PROPER POSITION 10
MOVING PROJECTOR 11
TERMINALS OF PROJECTOR 12
CONNECTING TO COMPUTERS 13
CONNECTING TO VIDEO EQUIPMENT 14
REMOTE CONTROL OPERATION 15
LASER POINTER FUNCTION 15
REMOTE CONTROL BATTERIES INSTALLATION 16
TOP CONTROLS AND INDICATORS 17
ON-SCREEN MENU 18
HOW TO OPERATE ON-SCREEN MENU 18
FLOW OF ON-SCREEN MENU OPERATION 18
MENU BAR 19
TURNING ON/OFF PROJECTOR 20
TURNING ON THE PROJECTOR 20
TURNING OFF THE PROJECTOR 21
ADJUSTING SCREEN 22
ZOOM ADJUSTMENT 22
FOCUS ADJUSTMENT 22
LENS SHIFT ADJUSTMENT 22
KEYSTONE ADJUSTMENT 22
PICTURE FREEZE FUNCTION 23
NO SHOW FUNCTION 23
P-TIMER FUNCTION 23
SOUND ADJUSTMENT 23
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.
SELECTING INPUT SOURCE 24
SELECTING COMPUTER SYSTEM 25
PC ADJUSTMENT 26
AUTO PC ADJUSTMENT 26
MANUAL PC ADJUSTMENT 27
PICTURE IMAGE SELECT 29
IMAGE LEVEL SELECT 29
PICTURE SCREEN ADJUSTMENT 30
PICTURE SCREEN SELECT 30
SELECTING INPUT SOURCE 31
SELECTING VIDEO SYSTEM 32
PICTURE IMAGE SELECT 33
IMAGE LEVEL SELECT 33
PICTURE SCREEN ADJUSTMENT 34
PICTURE SCREEN SELECT 34
SETTING MENU 38
WIRELESS MOUSE 45
MAINTENANCE 46
WARNING TEMP. INDICATOR 46
AIR FILTERS CARE AND CLEANING 47
CLEANING PROJECTION LENS 47
LAMP REPLACEMENT 48
LAMP REPLACE COUNTER 49
TROUBLESHOOTING 50
MENU TREE 52
COMPATIBLE COMPUTER SPECIFICATIONS 54
INDICATORS AND PROJECTOR CONDITION 55
TECHNICAL SPECIFICATIONS 57
CONFIGURATIONS OF TERMINALS 58
OPTIONAL PARTS 59
LENS REPLACEMENT 59
PJ LINK NOTICE 59
PIN CODE NUMBER MEMO 60
DIMENSIONS 61
PICTURE IMAGE ADJUSTMENTS 35
FEATURES AND DESIGN 6
PREPARATION 7
CONNECTING PROJECTOR 12
BEFORE OPERATION 15
BASIC OPERATION 20
COMPUTER INPUT 24
VIDEO INPUT 31
PICTURE IMAGE 35
SETTING 38
APPENDIX 45
6
FEATURES AND DESIGN
This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 1.07 billion colors, and matrix liquid crystal display (LCD)
technology.
◆ Compatibility
This projector widely accepts various video and
computer input signals such as:
● Computers
IBM-compatible or Macintosh computer up to 1600
x 1200 resolution.
● 6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M, or PAL-
N color system can be connected.
● Component Video
Component video signal, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i, or 1080i, can be
connected.
● S-Video
S-Video signal, such as a S-VHS VCR output
signal, can be connected.
◆ High Resolution Image
This projector provides 1024 x 768 dots resolution for
computer input and 800 horizontal TV lines. Resolution
from a computer between XGA (1024 x 768) and UXGA
(1600 x 1200) is compressed into 1024 x 768 dots. This
projector cannot display image of over 1600 x 1200 dots.
When resolution of your computer is over 1600 x 1200,
lower the resolution for a computer output.
◆ Multi-Scan System
This projector has the Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for a troublesome manual adjustment of frequency
and other settings.
◆ Keystone Correction
Positioning of the projector may result in distorted image
being displayed in a trapezoid shape. Keystone function
solves this problem by digitally altering the projection to
produce undistorted images.
◆ Multilanguage Menu Display
Operation menu is available in 12 languages: English,
German, French, Italian, Spanish, Portuguese, Dutch,
Swedish, Russian, Chinese, Korean, or Japanese.
◆ One-Touch Auto PC Adjustment
Incoming computer video signals are recognized and
best adjustment is automatically set by the Auto PC
Adjustment function. No complicated setup is necessary
and the projection is always precise.
◆ Digital Zoom (for Computer)
Digital Zoom function adjusts image size to approx. 1/4 ~
49 times of an original image size, allowing you to focus
on a crucial information at the presentation.
◆ Compact Design
This projector is extremely compact in size and weight.
It is designed to carry and work anywhere you wish to
use.
◆ Power Management
Power management function is provided to reduce power
consumption when the projector is not in use.
The Power management function operates to turn the
projection lamp off when the projector detects a signal
interruption or when no button is pressed for a certain
period. The projection lamp is automatically turned on
again when the projector detects a signal or any
operation button is pressed.
This projector is shipped with this function ON.
◆ Digital Visual Interface
This projector is equipped with the DVI 24-pin terminal
for connecting DVI output from a computer.
◆ Motor-driven Lens Shift
Projection lens can be moved up and down with the
motor-driven lens shift function. This function makes it
easy to provide projected image where you want.
Zoom and focus can also be adjusted with a motor-
driven operation.
◆ Pj-to NetDirector (Optional)
Pj-to NetDirector enables the projector to display the
image of the computer screen and the image data stored
in the computer via a network. The projector can also be
controlled and maintained through a web browser.
◆ Wireless Mouse
Remote control supplied with this projector has the
Wireless Mouse function for a connected computer. This
function enables you to operate both projector and
computer with the remote control only.
◆ Laser Pointer Function
Remote control supplied with this projector includes the
Laser Pointer function. This function helps you to make a
smart presentation on a projected screen.
7
PREPARATION
NAME OF EACH PART OF PROJECTOR
BOTTOM OF CABINET
BACK OF CABINET
HOT AIR EXHAUSTED !
Air blown from the exhaust vent is hot.
When using or installing the projector, the
following precautions should be taken.
● Do not put a flammable object near this vent.
● Keep the rear grills at least 3.3’ (1 m) away
from any object, especially from heat-
sensitive objects.
● Do not touch this area, especially screws
and metallic parts. This area will become hot
when the projector is in use.
This projector detects internal temperature
and automatically controls operating power
of the cooling fans.
FRONT OF CABINET
LAMP COVER
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
This projector is equipped with the cooling fans for protecting from
overheating. Pay attention to the following matters to ensure
proper ventilation and avoid a possible risk of fire and malfunction.
● Do not cover the vent slots.
● Keep this side clear of any objects. Obstructions may block
cooling air.
AIR INTAKE VENTS
PROJECTION LENS
SPEAKERS
INFRARED
REMOTE RECEIVER
LENS CAP
POWER CORD
CONNECTOR
EXHAUST VENT
TERMINALS
AND CONNECTORS
TOP CONTROLS
AND INDICATORS
INFRARED
REMOTE RECEIVER
CARRYING
HANDLE
AIR INTAKE
VENT
When attaching the Pj-to NetDirector
(optional) to the projector, remove these
parts. Refer to the owner’s manual of the
optional Pj-to NetDirector.
Do not turn on the projector with
the lens cap attached. High
temperature from light beam
may damage the lens cap and
result in fire hazard.
CAUTION
✽ Optional: LC-X71L
✽ Optional: LC-X71L
NOTE ON POWER CORD
AC power cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below and a proper AC power cord must be used.
If the supplied AC power cord does not match your AC outlet, contact your sales dealer.
SETTING-UP PROJECTOR
8
PREPARATION
To POWER CORD
CONNECTOR on your
projector.
Projector side AC Outlet side
Ground
To the AC Outlet.
(120 V AC)
For Continental Europe
For the U.S.A. and Canada
This projector uses nominal input voltages of 100-120 V or 200-
240 V AC and it automatically selects correct input voltage. It is
designed to work with single-phase power systems having a
grounded neutral conductor. To reduce risk of electrical shock, do
not plug into any other type of power system.
If you are not sure of the type of power being supplied, consult
your authorized dealer or service station.
Connect the projector with all peripheral equipment before turning
it on. (See pages 12-14 for connection.)
CAUTION
For safety, unplug the AC power cord when the projector is not
in use. When the projector is connected to an outlet with AC
power cord, an appliance is in stand-by mode and consumes a
little electric power.
CONNECTING AC POWER CORD
Connect AC power cord (supplied) to the
projector.
The AC outlet must be near this equipment and
must be easily accessible.
To the AC Outlet.
(200 - 240 V AC)
9
PREPARATION
Before setting up the projector, install a projection lens on
the projector.
1. Before installation, check the area where the projector is
used and prepare a suitable lens. For the specifications of
a projection lens, contact sales dealer where you
purchased the projector.
2. For installation, refer to the installation manual of the
optional lens.
LENS INSTALLATION
NOTE:
• When installing the lens, remove the cover cap of the projector.
COVER CAP
POSITIONING PROJECTOR
● This projector is designed to project on a flat projection surface.
● Projector can be focused from 4.6’ (1.4 m) ~ 48.3’ (14.7 m).
● Refer to the figure below to adjust the screen size.
Screen
Size
Distance
40”
31”
4.6’ (1.4 m)
40”
4.6’(1.4m)
11.8’(3.6m)
23.6’(7.2m)
35.4’(10.8m)
Max. Zoom
Min. Zoom
47.3’(14.4m)
100”
200”
300”
400”
308”
231”
154”
77”
31”
A ROOM LIGHT
Brightness in a room has a great
influence on the picture quality. It is
recommended to limit ambient lighting
in order to provide the best image.
Min. Zoom
Max. Zoom
100”
77”
11.8’ (3.6 m)
150”
115”
17.7’ (5.4 m)
200”
154”
23.6’ (7.2m)
250”
192”
29.5’ (9.0 m)
300”
231”
35.4’ (10.8 m)
400”
308”
47.3’ (14.4 m)
LENS SHIFT ADJUSTMENT
Projection lens can be moved up and down with the motor-driven Lens shift function. This function makes it easy
to provide projected image where you want. The U/D ratio can be adjusted 10:0 ~ 1:1 (see Figure below). See
page 22 for operation.
Highest (10 : 0) Lowest (1 : 1)
NOTE: The figures below are only for the Model LC-X71.
The projection lens is not provided with the Model LC-X71L.
10
PREPARATION
ADJUSTABLE FEET
Projection angle can be adjusted up to 10.5 degrees with the
ADJUSTABLE FEET.
Lift the front of the projector and pull the FEET LOCK
LATCHES in each side of the projector.
1
Release the FEET LOCK LATCHES to lock the
ADJUSTABLE FEET and rotate the ADJUSTABLE FEET to a
proper height, and tilt.
2
To retract the ADJUSTABLE FEET, lift the front of the
projector and pull and undo the FEET LOCK LATCHES.
Keystone distortion of the projected image can be adjusted by
the Menu Operation. (See pages 22 and 38.)
3
INSTALLING PROJECTOR IN PROPER POSITION
Install the projector properly. Improper installation may reduce the lamp life and cause a fire hazard.
Do not tilt the projector more than 10 degrees from side to side.
Do not put the projector on either side to project an image.
NO SIDEWAYS
10˚
10˚
ADJUSTABLE FEET FEET LOCK
LATCHES
11
PREPARATION
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR
● Do not drop or bump the projector, otherwise damages or malfunctions may result.
● When carrying the projector, use a suitable carrying case.
● Do not transport the projector by courier or any other transport service in an unsuitable transport case.
This may cause damage to the projector. To transport the projector by courier or any other transport
service, consult your dealer for the best way.
MOVING PROJECTOR
Use the Carrying Handle when moving the projector.
Replace the lens cap and retract the ADJUSTABLE FEET
when moving the projector to prevent damages to the lens
and cabinet.
When this projector is not in use for an extended period, put
it into a suitable case (not supplied with this projector).
12
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector has input and output terminals on its back for connecting computers and video equipment. Refer
to the figures on pages 12 to 14 and connect properly.
Connect external speakers to
these terminals. (See pages 13
and 14.)
EXTERNAL SPEAKER TERMINALS
When controlling a computer
with the remote control of this
projector, connect the mouse
port of your personal computer
to this connector. (See page
13.)
Connect S-VIDEO
output from video
equipment to this
jack. (See page 14.)
Connect an audio output
from video equipment to
these jacks. (See page
14.)
CONTROL PORT CONNECTOR
COMPUTER AUDIO INPUT 1/
AUDIO MONITOR OUTPUT
JACK
AUDIO INPUT JACKS
VIDEO INPUT JACKS
S-VIDEO INPUT JACK
Connect composite video
output from video equipment
to VIDEO/Y jack or connect
component video outputs to
VIDEO/Y, Cb/Pb and Cr/Pr
jacks. (See page 14.)
This terminal is switchable and
can be used as Computer Input
or Monitor Output. Set up the
terminal as either Computer Input
or Monitor Output properly before
using this terminal.
(See pages 13-14 and 24.)
Note: This terminal outputs from the 5
BNC type computer input on INPUT 2
jacks only.
COMPUTER INPUT/MONITOR
OUTPUT TERMINAL (ANALOG)
This projector uses a micro
processor to control the unit, and
only occasionally, this micro
processor may malfunction and
need to be reset. This can be done
by pressing the RESET button with
a pen, which will shut down and
restart the unit. Do not use the
RESET function excessively.
RESET BUTTON
When controlling a computer
with the remote control of this
projector, connect USB terminal
of your personal computer to
this terminal. (See page 13.)
USB CONNECTOR (Series B)
Connect component video
output (Y, Cb, Cr or Y, Pb, Pr)
from video equipment to
VIDEO/Y, Cb/Pb and Cr/Pr
jacks or connect computer
output {5 BNC Type (Green,
Blue, Red, Horiz. Sync, and
Vert. Sync.)} from computer to
G, B, R, H/V, and V jacks.
(See pages 13 and 14.)
5 BNC INPUT JACKS
When using the Wired/
Wireless remote control as
wired, connect the Wired
remote control to this jack with
a remote control cable
(optional).
R/C JACK
Connect an audio
output (stereo) from a
computer to this jack.
(See page 13.)
COMPUTER AUDIO
INPUT 2 JACK
Connect a computer output
(Digital DVI-D type) to this
terminal.
The HD (HDCP Compatible)
signal can also be connected.
(See page 13.)
COMPUTER INPUT
TERMINAL (DIGITAL)
This terminal is switchable and
can be used as Computer
Audio Input 1 or Audio Monitor
Output (variable).
Set up the terminal as either
Computer Audio Input 1 or
Audio Monitor Output properly
before using this terminal.
(See pages 13 and 24.)
13
CONNECTING PROJECTOR
S–VIDEO
R–AUDIO–L
VIDEO/Y Cb/Pb Cr/Pr
VIDEO/Y Cb/Pb Cr/Pr
RESET
CONTROL PORT
USB
AUDIO 1
AUDIO 2
ANALOG IN/OUT
DIGITAL(DVI-D)
INPUT 1
INPUT 2
INPUT 3
R/C JACK
G B R H/V V
(
MONO
)
IN/OUT
CONNECTING TO COMPUTERS
IBM-compatible computer or Macintosh computer (VGA/SVGA/XGA/SXGA/SXGA+/WXGA/UXGA )
VGA Cable
Monitor Output
Desktop type Laptop type
Control Cable
for Serial Port
Terminal
Serial port PS/2 portAudio Output
CONTROL
PORT
COMPUTER
AUDIO IN 1 or 2
COMPUTER IN ANALOG
Use one of these Control
Cables corresponding with
terminal of your computer.
ADB port
Cables used for connection (✽ = Cables or adapters not supplied with this projector.)
Control Cable
for PS/2 Port ✽
Control Cable
for ADB Port ✽
Audio
Cable
✽
(stereo)
NOTE:
Unplug the power cords of both the projector and
external equipment from the AC outlet before
connecting cables. Turn a projector and peripheral
equipment on before computer is switched on.
USB port
• VGA Cable (HDB 15 pin)
• DVI-Digital Cable (for Single Link T.M.D.S.)
✽
• BNC Cable ✽
• Control Cable for Serial Port
• Control Cable for PS2 Port ✽, or ADB Port ✽
• USB Cable
• Audio Cables (Mini Plug (stereo) x 2)
✽
Terminals
of the Projector
Terminal
Terminal
DVI
Cable
✽
Monitor Output
USB
COMPUTER IN DIGITAL
USB
Cable
BNC
Cable
✽
Audio Speakers
(stereo)
Audio Amplifier
Audio Cable
(stereo) ✽
Audio Input
AUDIO OUT
External Audio Equipment
Monitor Output
or
Monitor Input
NOTE:
This terminal is switchable.
Set up the terminal as either
Computer input or Monitor
output before using this
terminal.(See page 24.)
NOTE:
This terminal is switchable.
Set up the terminal as
either Computer Audio
Input 1 or Audio Monitor
Output (variable) before
using this terminal. (See
page 24.)
External Speaker Terminals
(Front of the projector)
Audio Speakers
(stereo)
14
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
Video Source (Example)
Video Cassette Recorder Video Disc Player
S-VIDEO
Cable ✽
Terminals
of the Projector
S-VIDEO
Output
Cables used for connection (✽ = Cables not supplied with this projector.)
Audio Cable
(RCA x 2) ✽
AUDIO IN S-VIDEO
Y - Cb/Pb - Cr/Pr
VIDEO
Component video output equipment.
(such as DVD players or high-definition TV sources.)
Composite
Video Output
Component Video
Output
(Y, Cb/Pb, Cr/Pr)
Component Video
Output
(Y, Cb/Pb, Cr/Pr)
Y - Cb/Pb - Cr/Pr
Video Cables
(RCA x 1 or
RCA x 3) ✽
BNC Cable ✽
Audio Output
Composite
Video Output
VIDEO
• Video Cable (RCA x 1 or RCA x 3) ✽
• BNC Cable ✽
• S-VIDEO Cable ✽
• Audio Cable (RCA x 2) ✽
• Audio Cable {Mini Plug (stereo)} ✽
• Scart Cable ✽
Audio Speakers
(stereo)
Audio Amplifier
Audio Cable
(stereo) ✽
Audio Input
AUDIO OUT
External Audio Equipment
RGB Scart
21-pin Output
Scart Cable ✽
COMPUTER IN ANALOG
NOTE:
This terminal is switchable.
Set up the terminal as either
Computer input or Monitor
output before using this
terminal.(See page 24.)
NOTE:
Unplug the power cords of both the projector
and external equipment from the AC outlet
before connecting cables.
External Speaker Terminals
(Front of the projector)
Audio Speakers (stereo)
Audio
Cable
✽
(stereo)
Audio Output
AUDIO IN
15
BEFORE OPERATION
FOCUS BUTTON
Used to adjust focus. (p.22)
AUTO PC ADJ. BUTTON
Use to operate the AUTO PC
Adjustment function. (p.26)
KEYSTONE BUTTON
Used to correct keystone
distortion. (p.22, 38)
IMAGE BUTTON
Used to select the image
level. (p.29, 33)
FREEZE
FREEZE
SELECT
D.ZOOM
D.ZOOM
MUTE
MUTE
VOLUME
-
MENU
MENU
NO S
OS
HOW
HOW
IMAGE
IMAGE
VOLUME
+
KEYSTONE
TONE
LASER
LASER
P-TIMER
P-TIMER
ZOOM
INPUT 1
INPUT 1
INPUT 2
INPUT 2
INPUT 3
INPUT 3
FOCUS
FOCUS
LENS
AUT
AUT
O P
OP
C
ON-OFF
ON-OFF
LOCK
LOCK
COLOR.M
COLOR.M
REMOTE CONTROL OPERATION
ALL OFF SWITCH
Left Side
When using the remote control, turn
this switch to “ON.” And turn it to
“ALL OFF” when it is not in use.
This remote control emits laser beam from the Laser Light Window when used as a Laser Pointer. When the
LASER button is pressed, the laser light goes on. When the LASER button is being pressed for more than one
minute or when it is released, the light goes off. The LASER POINTER INDICATOR lights RED and the LASER
is emitted with RED light to indicate the laser beam is being emitted.
The Laser emitted is the Cass II laser. Do not look into the Laser Light Window or shine laser beam onto yourself
or other people. The three marks shown below are caution labels for the laser beam.
CAUTION: Use of controls, adjustments, or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
LASER LIGHT WINDOW
These caution labels are put on the remote control.
LASER POINTER FUNCTION
POWER ON-OFF BUTTON
Used to turn the projector on
or off. (p.20, 21)
LASER BUTTON
Used to operate the Laser
Pointer function. The laser
beam is emitted when
pressing this button for one
minute.
When using the Laser Pointer
for more than one minute,
release this button and press
it again.
Used as a PC mouse in
Wireless Mouse Operation.
(p.45)
MOUSE POINTER
Used as a PC mouse in
Wireless Mouse Operation.
(p.45)
RIGHT CLICK BUTTON
Lights red while the laser
beam is emitted from the
Laser Light Window.
Lights green when dragged
to the “ON” position. (p.45)
LASER POINTER
(DRAG ON) INDICATOR
LASER POINTER INDICATOR
LENS SHIFT BUTTON
Used to select the Lens Shift
function. (p.22)
MUTE BUTTON
Used to mute the sound.
(p.23)
DRAG ON/OFF BUTTON
Used to select the DRAG
ON/OFF position. (p.45)
Used as a PC mouse in
Wireless Mouse Operation.
Press this button and the
mouse pointer button to drag
the selected screen object.
(p.45)
LEFT CLICK BUTTON
SW1 SW2 SW3 Code No.
DIP SWITCH SETTING
SW4 ........ LASER ON/OFF
4
ON
321
Code 1ON ON Code 1ON
Code 4ON OFF
Code 2ON OFF
Code 3ON ON
Code 5OFF ON
Code 6OFF OFF
Code 7OFF ON
Code 8OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF OFF
INSIDE THE BATTERY
COMPARTMENT BOX
This Remote Control provides the DIP
switches into the battery compartment
box.
Slide the SW4 (LASER ON/OFF
switch) to the “OFF” position. The
Laser Pointer function is not operated.
Set the Switches 1-3 as shown in table
below depending on the Code No. that
you want to select as the remote
control code. (See page 41.)
WIRED REMOTE JACK
When using as a Wired
Remote Control, connect a
remote control cable (optional)
to this jack.
Battery installation is required
when using as a Wired
Remote Control.
16
BEFORE OPERATION
To insure safe operation, please observe following precautions:
● Use two (2) AA or LR6 type alkaline batteries.
● Always replace batteries in sets.
● Do not use a new battery with an used battery.
● Avoid contact with water or liquid.
● Do not expose the remote control to moisture, or heat.
● Do not drop the remote control.
● If a battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
● Danger of explosion if battery is incorrectly replaced.
● Dispose of used batteries according to batteries manufacturers instructions and local rules.
Press the lid downward
and slide it.
Open the battery
compartment lid.
Install new batteries into
the compartment.
Replace the compartment lid.
Two AA size batteries
For correct polarity (+ and
–), be sure battery terminals
are in contact with pins in
the compartment.
REMOTE CONTROL BATTERIES INSTALLATION
1 2 3
Used to operate the P-
TIMER function. (p.23)
FREEZE
FREEZE
SELECT
D.ZOOM
D.ZOOM
MUTE
MUTE
VOLUME
-
MENU
MENU
NO S
OS
HOW
HOW
IMAGE
IMAGE
VOLUME
+
KEYSTONE
TONE
LASER
LASER
P-TIMER
P-TIMER
ZOOM
INPUT 1
INPUT 1
INPUT 2
INPUT 2
INPUT 3
INPUT 3
FOCUS
FOCUS
LENS
AUT
AUT
O P
OP
C
ON-OFF
ON-OFF
LOCK
LOCK
COLOR.M
COLOR.M
P-TIMER BUTTON
Used to adjust zoom.
(p.22)
ZOOM BUTTON
NO SHOW BUTTON
Used to turn the picture
into a black image. (p.23)
D.ZOOM BUTTON
Used to select the
DIGITAL ZOOM +/– mode
and resize the image.
(p.30)
FREEZE BUTTON
Used to freeze the picture.
(p.23)
MENU BUTTON
Used to select the MENU
Operation. (p.18, 19)
INPUT 1 BUTTON
Used to select an input
source (INPUT 1). (p.24)
SELECT BUTTON
Used to execute the
selected item, or expand/
compress the image in the
DIGITAL ZOOM +/- mode.
(p.30)
POINT (VOLUME +/-)
BUTTONS
Used to select an item or
adjust a value in On-Screen
Menu. They are also used to
pan the image in the
DIGITAL ZOOM +/- mode.
(p.30)
The POINT LEFT/RIGHT
buttons are also used as
VOLUME +/- buttons. (p.23)
INPUT 2 BUTTON
Used to select an input
source (INPUT 2).
(p.25, 31)
INPUT 3 BUTTON
Used to select an input
source (INPUT 3). (p.31)
Operating Range
Point the remote control toward
the projector (a Receiver
Window) when pressing any
button. Maximum operating
range for the remote control is
about 16.4’ (5 m) and 60° in front
and rear of the projector.
16.4’
(5 m)
60°
16.4’
(5 m)
60°
COLOR MANAGEMENT
BUTTON
Used to operate the Color
management function.
(p.35-36)
17
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
Used to open or
close the On-Screen
Menu. (p.18, 19)
MENU BUTTON
IMAGE BUTTON
READY INDICATOR
SELECT BUTTON
POWER ON–OFF BUTTON
INPUT BUTTON
WARNING TEMP. INDICATOR
LAMP INDICATOR
POINT (VOLUME + / – ) BUTTONS
LAMP REPLACE INDICATOR
Used to select the
image level. (p.29, 33)
Lights green when the
projector is ready to be
turned on. And it blinks
green in the Power
management mode.
(p.40, 46, 55-56)
Becomes dim when the
projector is turned on.
And it becomes bright
when the projector is in
stand-by mode. (p.20,
21, 55-56)
Turns to yellow when the
projection lamp reaches its
end of life.
Blinks yellow when the
lamp cannot light up. (p.48,
55-56)
Blinks red when the internal
temperature of the projector
is too high. (p.46, 55-56)
Used to select an input
source. (p.24, 31)
Used to select an item or adjust a
value in On-Screen Menu. They are
also used to pan the image in the
DIGITAL ZOOM +/– mode. (p.30)
The POINT LEFT/RIGHT buttons are
also used as VOLUME +/– buttons.
(p.23)
Used to execute the
selected item. It is also
used to expand/compress
the image in the DIGITAL
ZOOM mode. (p.30)
Used to turn the projector
on or off. (p.20, 21)
Used to adjust zoom.
(p.22)
FOCUS BUTTON
Used to adjust focus.
(p.22)
ZOOM BUTTON
This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.
LENS SHIFT BUTTON
Used to select the Lens
Shift function. (p.22)
AUTO PC ADJ. BUTTON
Used to operate the Auto
PC Adjustment function.
(p.26)
KEYSTONE BUTTON
Used to correct
keystone distortion.
(p.21, 37)
Used to select speakers.
(Internal or External)
EXT. SP SWITCH
TOP CONTROLS AND
INDICATORS
18
BEFORE OPERATION
HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector with the On-
Screen Menu. Refer to the relevant pages to operate
each adjustment.
2. MOVING POINTER
3. SELECT ITEMS
Move the pointer (✽ see below) or adjust a value of an item by
pressing the POINT buttons on the top control or on the remote
control.
Select an item or set the selected function by pressing the
SELECT button.
ON-SCREEN MENU
✽ The Pointer is an icon in the On-Screen Menu for selecting
an item. See figures in “FLOW OF ON-SCREEN MENU
OPERATION” below.
Used to select the item.
SELECT BUTTON
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
POINT BUTTONS
TOP CONTROL
MENU BAR MENU ICON
SELECT
BUTTON
1. DISPLAY MENU
Press the MENU button to display the On-Screen Menu.
FLOW OF ON-SCREEN MENU OPERATION
Display ON-SCREEN MENU
Press the MENU button to display the On-Screen Menu
(a MENU BAR). A red frame is a POINTER.
Move the POINTER (red frame) to a MENU ICON that
you want to select by pressing the POINT RIGHT/LEFT
buttons.
Adjust the ITEM DATA by pressing the POINT
RIGHT/LEFT buttons.
Refer to the relevant pages for details of respective
adjustments.
Press the POINT UP/DOWN buttons and move the
POINTER (red frame or red arrow) to an ITEM that you
want to adjust, and then press the SELECT button to
show the ITEM DATA.
Select Menu to be adjusted
Control or adjust items through ON-SCREEN MENU
1
2
4
3
POINTER (red frame)
Press the POINT UP/DOWN
buttons to move the POINTER.
POINTER
(red frame)
ITEM
ITEM DATA
Press the POINT LEFT/RIGHT
buttons to adjust a value or set a
function.
MENU BUTTON
Used to select the item.
SELECT BUTTON
Used to move the
Pointer UP/DOWN/
RIGHT/LEFT.
POINT BUTTONS
REMOTE CONTROL
FREEZE
FREEZE
SELECT
D.ZOOM
D.ZOOM
MUTE
MUTE
VOLUME
-
MENU
MENU
NO S
OS
HOW
HOW
IMAGE
IMAGE
VOLUME
+
KEYSTONE
TONE
AUT
AUT
O P
OP
C
ON-OFF
ON-OFF
LOCK
LOCK
MENU BUTTON
19
BEFORE OPERATION
MENU BAR
FOR PC SOURCE
Press the MENU button when connecting to the PC input source.
FOR VIDEO SOURCE
Press the MENU button when connecting to the VIDEO input source.
Same function as
menu for PC source.
Same function as
menu for PC source.
GUIDE WINDOW
Shows the
selected item of
On-Screen Menu.
PC SYSTEM MENU
Used to select a
computer system.
(See pages 24
and 25.)
IMAGE SELECT MENU
Used to select an
image level among
Standard, Real, and
Image 1 ~ 10.
(See page 29.)
SCREEN MENU
Used to adjust the
size of an image.
[Normal/True/Wide/
Full/Digital zoom
+/–] (See page 30.)
SETTING MENU
Used to change
settings of the projector
or reset the Lamp
replacement counter.
(See pages 38-44.)
SOUND MENU
Used to adjust
the volume or
mute the sound.
(See page 23.)
IMAGE ADJUST MENU
Used to adjust the computer
image. [Contrast/
Brightness/Color/Tint/Color
management/Auto picture
control/Color temp./White
balance (R/G/B)/Sharpness/
Gamma/Noise reduction/
Progressive] (See pages
35-37.)
PC ADJUST MENU
Used to adjust
the parameters
to match with the
input signal
format. (See
pages 26-28.)
INPUT MENU
Used to select an
input source (Input 1,
Input 2, or Input 3).
(See page 24.)
INPUT MENU
Used to select an
input source
(Input 1, Input 2,
or Input 3). (See
page 31.)
IMAGE SELECT MENU
Used to select an
image level among
Standard, Cinema,
and Image 1 ~ 10.
(See page 33.)
SCREEN MENU
Used to adjust the size
of image to Normal or
Wide. (See page 34.)
IMAGE ADJUST MENU
Used to adjust the picture
image. [Contrast/Brightness/
Color/Tint/Color management/
Auto picture control/Color
temp./White balance (R/G/B)/
Sharpness/Gamma/Noise
reduction/Progressive] (See
pages 35-37.)
AV SYSTEM MENU
Used to select the
system of selected
video source. (See
page 32.)
20
BASIC OPERATION
TURNING ON THE PROJECTOR
TURNING ON / OFF PROJECTOR
Connect the projector’s AC power cord into an AC outlet. The
LAMP indicator lights RED, and the READY indicator lights
GREEN.
Press the POWER ON-OFF button on the top control or on
the remote control. The LAMP indicator dims, and the cooling
fans start to operate. The preparation display appears on the
screen and the countdown starts.
2
3
1
4
After the countdown, the input source that was selected the
last time and the Lamp control status icon (see page 41)
appear on the screen.
If the projector is locked with a PIN code, a PIN code Input
Dialog Box appears. Enter a PIN code as instructed below.
Complete peripheral connections (with a computer, VCR, etc.)
before turning on the projector.
What is PIN code?
PIN (Personal Identification Number) code is a security code that
allows the person who knows it to operate the projector. Setting a
PIN code prevents unauthorized use of the projector.
A PIN code consists of a four-digit number. Refer to the PIN code
lock function in SETTING Menu on page 43 for locking operation
of the projector with your PIN code.
To Enter a PIN code
Select a number by pressing the POINT LEFT/RIGHT button and
fix the number with the SELECT button. The number changes to
“✳.” If you fixed a wrong number, move the pointer to “Set” or
“Clear” once by pressing the POINT DOWN button, then return to
“PIN code.” Enter the correct number.
Repeat this step to complete entering a four-digit number.
When the four-digit number is fixed, the pointer automatically
moves to “Set.” Press the SELECT button so that you can start to
operate the projector.
If you entered a wrong PIN code, “PIN code” and the number
(✳✳✳✳) turn red and disappear. Enter a PIN code all over again.
CAUTION ON HANDLING PIN CODE
If you forget your PIN code, the projector can no
longer be started. Take special care in setting a new
PIN code; write down the number in a column on
page 60 of this manual and keep it at hand. Should
the PIN code be missing or forgotten, consult your
dealer or service center.
16
The preparation display disappears after 30 seconds.
Selected Input Source and Lamp control
Pointer
PIN code Input Dialog Box
After the OK icon
disappears, you can
operate the projector.
Lamp control status
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
