Electrolux WT830M240U User manual

DOC. NO. 5956.446.06 P. 1 / 11 4

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

SERVICE MANUAL

CONTENTS: This document contains the instruction to change parameter settings of electronic

board by means of user interface.

EDITION: 03.2010

TANK

BOILER

3.__

TANK

BOILER

3...__

TANK

BOILER

3.__

DOC. NO. 5956.446.06 P. 2 / 11 4

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

INDICE

1 KEYBOARDS Pag. 3

1.1 HOOD TYPE Style Pag. 3

1.2 UNDERCOUNTER Style Pag. 4

2 MANUAL ACTIVATION OF DETERGENT AND RINSE AID DISPENSERS Pag. 5

2.1 Detergent Dispenser Activation Pag. 5

2.2 Rinse Aid Dispenser Activation Pag. 5

3 RINSE PUMP MANUAL ACTIVATION Pag. 5

4 DETERGENT AND RINSE AID DOSAGE Pag. 6

4.1 GEn General Parameters Pag. 6

5COUNTERS Pag. 8

5.1 Cnt Counters Pag. 8

6 TEMPERATURE SETTING Pag. 10

6.1 FAC Factory Parameters Pag. 10

7 CYCLE SETTING Pag. 12

7.1 CYCLE DIAGRAM Pag. 13

7.2 CY1 Cycle 1 Parameters Pag. 14

7.3 CY2 Cycle 2 Parameters Pag. 14

7.4 CY3 Cycle 3 Parameters Pag. 14

7.5 drn Drain/Cleaning Cycle Parameters Pag. 14

8 OTHER PARAMETERS Pag. 15

8.1 dPA Dishwashing Parameters Pag. 15

8.2 ron Read Only Parameters Pag. 16

8.3 HCP Communication and HACCP Parameters Pag. 16

8.4 CFG Configuration Parameters Pag. 17

8.5 dbG Parameters for automatic hood type dishwashers Pag. 18

9 SPECIAL FEATURES Pag. 19

9.1 RESIN REGENERATION CYCLE Pag. 19

9.2 MEDICAL LINE DISHWASHER WITH DOOR/HOOD LOCK DEVICE Pag. 19

9.3 DETERGENT AND RINSE AID LEVEL SENSORS ACTIVATION Pag. 19

9.4 DISHWASHER WITH INCORPORATED CONTINUOUS WATER SOFTENER Pag. 20

10 MAIN BOARD CONFIGURATION Pag. 22

10.1 CODE -> Prog. TABLE Pag. 22

10.2 PROGRAMMING SHEETS Pag. 27

11 DEFAULT VALUES Pag. 91

12 USER INTERFACE AND MAIN BOARD CONNECTORS Pag. 94

12.1 Main malfunctions not due to the main board Pag. 94

12.2 CONNECTORS LAYOUT Pag. 94

13 ALARM MESSAGES AND TROUBLESHOOTING Pag. 107

13.1 ALARMS THAT STOP THE DISHWASHER Pag. 107

13.2 ALARMS THAT DON'T STOP THE DISHWASHER Pag. 111

13.3 ALARMS THAT DON’T STOP THE DISHWASHER FOR MODELS WITH

INCORPORATED CONTINUOUS WATER SOFTENER Pag. 113

14 LIST OF PARAMETERS FOR SUBSEQUENT VERSIONS Pag. 114

DOC. NO. 5956.446.06 P. 3 / 11 4

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

1 KEYBOARDS

1.1 HOOD TYPE Style

SETTING MODES:

To enter into one setting mode (Figure 4),(Figure 5) the appliance should be in stand-by: switch on the appli-

ance, no cycles selected. Is useful keep door open to avoid start cycle in case of not simultaneously pressure

of the two keys.

Fig.1 Detergent dispenser Manual

Activation.

Fig.2 Rinse Aid Dispenser Manual

Activation

Fig.3 Rinse Pump Manual

Activation (used to EMPTY

BOILER)

Fig.4 Enter into General

Parameters (Hold down buttons for

at least five seconds).

Fig.5 Enter into Factory

Parameters (Hold down buttons for

at least five seconds)..

Fig.6 Next Parameter Family OR

Increase Parameter Value(In setting

mode only)

Fig.7 Decrease Parameter

Value(In setting mode only)

Fig.8 Confirm Value and go to

next Parameter (In setting mode

only).

dEt

rAi

---

GEn

FAC

888

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

DOC. NO. 5956.446.06 P. 4 / 11 4

1.2 UNDERCOUNTER Style

SETTING MODES:

To enter into one setting mode (Figure 12), (Figure 13) the appliance should be in stand-by: switch on the

appliance, no cycles selected. Is useful keep door open to avoid start cycle in case of not simultaneously

pressure of the two keys.

Fig.9 Detergent dispenser Manual

Activation

Fig.10 Rinse Aid Dispenser

Manual Activation

Fig.11 Rinse Pump Manual

Activation (used to EMPTY BOILER)

Fig.12 Enter into General

Parameters (Hold down buttons for

at least five seconds).

Fig.13 Enter into Factory

Parameters (Hold down buttons for

at least five seconds).

Fig.14 Next Parameter Family OR

Increase Parameter Value (in

setting mode only)

Fig.15 Decrease Parameter Value

(In setting mode only)

Fig.16 Confirm Value and go to

next Parameter (in setting mode

only).

TANK

BOILER

dEt

TANK

BOILER

rAi

TANK

BOILER

---

TANK

BOILER

GEn

TANK

BOILER

FAC

TANK

BOILER

888

TANK

BOILER

888

TANK

BOILER

888

DOC. NO. 5956.446.06 P. 5 / 11 4

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

2 MANUAL ACTIVATION OF DETERGENT AND RINSE AID

DISPENSERS

When replacing detergents may be necessary activate the dispensers to fill hoses.

2.1 Detergent Dispenser Activation

2.2 Rinse Aid Dispenser Activation

3 RINSE PUMP MANUAL ACTIVATION

Use this function to empty the boiler (if the dishwasher is not to be used for a long time, for maintenance oper-

ation: ex. before replacing main board).

Switch on the dishwasher.

Press and hold down CYCLE_2 and CYCLE INFINITE keys, after two

'beep' the detergent dispenser starts work for 20 sec.

Switch on the dishwasher.

Press and hold down CYCLE_1 and CYCLE INFINITE keys, after two

'beep' the rinse aid dispenser starts work for 40 sec.

Switch on the dishwasher.

Close the door and press and hold down DRAIN and CYCLE INFINITE

keys. A buzzer signal indicates the rinse pump activation and the dis

-

play shows three blinking lines. Three beeps indicate the cycle end.

dEt

rAi

---

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

DOC. NO. 5956.446.06 P. 6 / 11 4

4 DETERGENT AND RINSE AID DOSAGE

In this paragraph is explained how to set the working time for the detergent and rinse aid dispensers.

For each dispenser there are two parameters: the initial time and the time during cycle execution.

4.1 General Parameters

How change the duration:

• Switch OFF and switch ON the dishwasher;

• Enter into the USER SETTING mode by pressing and hold down ON/OFF and CYCLE_1 keys for at least five sec-

onds the display shows  (Figure 17);

• Press CYCLE_INFINITE. The display shows alternatively the symbol dIn and the duration in seconds (Figure 18) and

(Figure 19) ;

• NOTE: If User Interface v.3.00 tank led is on if value correspond to factory default ( Default 1 - HOOD TYPE).

• Use CYCLE_1 key to decrease the duration and CYCLE_2 key to increase (Figure 19);

• After settled the duration press CYCLE_INFINITE key to store value. The display shows the next parameter (Fig-

ure 20) and the corresponding value (Figure 21);

• In the same way is possible to change the other duration; when finished switch OFF and switch ON.

Sym. Parameter Description Unit Min Max Factory Default



Initial Detergent Dosage (during filling tank) [s] 0 240 90



Initial Rinse Aid Dosage (starts when tank filled) [s] 0 180 10



Detergent Dosage During Cycle Execution (during wash

phase)

[s] 0 182 (*) 8



Rinse Aid Dosage During Cycle Execution (when refill-

ing boiler)

[s] 0 62 (*) 4

Fig.17 Enter into User Mode (press for 5 sec)..

Fig.18 Initial detergent

dosage.

Fig.19 Change duration.

(Tank LED indicates default).

Fig.20 Initial rinse aid

dosage

Fig.21 Change duration

Fig.22 Cycle detergent

dosage.

Fig.23 Change time

activation (Tank LED

indicates default)

Fig.24 Cycle rinse aid

dosage.

Fig.25 Change time

activation.

GEn

dIn 90 rIn 24

Val.Fabbr.

dEt 8 rAi 7

Val.Fabbr.

DOC. NO. 5956.446.06 P. 7 / 11 4

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

(*) Note for external dispensers:

•if the detergent dispenser works when WASHING PUMP is being activated; at the

same time voltage is supplied between connectors L1

7

–L1

9

(main terminal box);

•if the detergent dispenser works when LOADING EV is being activated to re-fill

boiler level; at the same time voltage is supplied between connectors L1

7

–L1

9

(main terminal box);

•if the rinse aid dispenser works when LOADING EV is being activated to re-fill boiler

level; at the same time voltage is supplied between connectors L1

8

–L1

9

(main ter-

minal box);

•if the rinse aid dispenser works when WASHING PUMP is being activated; at the

same time voltage is supplied between connectors L1

8

–L1

9

(main terminal box);

- For electrical connections refer to electric diagram -

Example

Suppose there is connected an external detergent dispenser with a probe into the tank. A typical setting

could be:

 the dispenser is not activated during filling tank.

 the dispenser is supplied during washing phase and the probe automatically dose the right

detergent amount.

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

DOC. NO. 5956.446.06 P. 8 / 11 4

5 COUNTERS

This Parameter Family collects cycle counters and water consumption counters.

For water consumption counters a flow meter must be installed. See (calibration parameter) into 

section (

8 OTHER PARAMETERS).

5.1 Counters

Sym. Parameter Description Unit Min Max

Factory

Default



Cycles performed counter.

 symbol and two numbers blink consecutively. The cycle number

is obtained by joining the two numbers.

Ex.      means 10042 cycles executed.

-



Cycle counter (resettable).

This counter is similar to  but is resettable by user (see 

parameter below).

-



Water Consumption (only for dishwashers with incorporated continuous

water softener).

Counts m

3

of water consumption.

[m

3

]



Water Consumption (only for dishwashers with incorporated continu-

ous water softener).

Counts litres of water consumption.

The total consumption is given by adding [m

3

] and [l] values.

[l]



Water Consumption: resettable counter. [present up to software version

3.12]

Counts the litres of water and is resettable by user (see  parame-

ter below).

[l]



Reset resettable counters:  and 

To reset put 1 this parameter, switch off and then on again:  and

 will show zero. Note that  is used to count cycles for

 message (see next parameter, ).

-



Store thousand of cycles after that  message appears on dis-

play.

Ex. If this parameter is settled to 20, message appears when

 reach 20.000 cycles.

-



Drain/Cleaning cycles performed.

Similar to  but counts Cleaning Cycles.

-



Numbers of cycles that can be made after a regeneration cycle (only for

dishwashers with non-continuous water softener) [See paragraph

9.1

RESIN REGENERATION CYCLE.].

- 20



Regeneration cycle counter (only for water softener dishwasher)

[See paragraph 9.4 DISHWASHER WITH INCORPORATED CONTI-

NUOUS WATER SOFTENER].  only counts efficient regenera-

tion cycles, i.e. those carried out with salt in the special container (only

for dishwashers with incorporated continuous water softener)

-



Counter of regeneration cycles done without salt in the special con-

tainer. (only for dishwashers with incorporated continuous water sof-

tener) [See paragraph 9.4 DISHWASHER WITH INCORPORATED

CONTINUOUS WATER SOFTENER].

-

DOC. NO. 5956.446.06 P. 9 / 11 4

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

Fig.26 USER setting mode

(press for 5s).

Fig.27 Next Family Fig.28 Counters Fam.:

ENTER

Fig.29 CYCLES Fig.30 Thousand. Fig.31 Units. Fig.32 Next counter.

GEn GEn

Cnt

CYC 010

042 cYc

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

DOC. NO. 5956.446.06 P. 10 / 114

6 TEMPERATURE SETTING

In this paragraph is explained how to change temperature thresholds and all parameters related to boiler and

tank

.

6.1  Factory Parameters

Sym. Parameter Description Unit Min Max

Factory

Default



Boiler Temperature: THRESHOLD.

When boiler temperature reaches this value, heaters switch off.

[°C] 45 95 78



Boiler Temperature HISTERESIS, (represent dead band).

Heater switch on if boiler temperature is below:  - 

[°C] 2 10 2



Boiler Temperature: HIGH LIMIT.

When boiler temperature reaches this value  alarm appears.

Put 0 to disable  alarm.

[°C] 0 98 96



Boiler Temperature: LOW LIMIT.

During boiler warm-up, temperature must increase at least  °C

otherwise  warning appears.

Put 0 to disable  warning.

[°C] 0 10 1



Boiler Filling Timeout.

If filling time is longer than , alarm appears.

Put 0 to disable  alarm.

[min] 0 42 5



Boiler Temperature Adjust.

[°C] 0 7 4



Boiler Priority (enable boiler wait function)

0=disabled

1=enabled

- 0 1 1



Booster Function

Overheat gap over Boiler Temperature Threshold

[°C] 0 15 2



Boiler temperature negative differential: when the dishwasher is in

standby, boiler threshold becomes:

 - 

(Used to save energy during machine inactivity by keeping boiler

water at a lower temperature).

[°C] 0 20 0



Tub Temperature: THRESHOLD

When tank temperature reaches this value, heater switch off.

[°C] 40 85 63



Tub Temperature: HISTERESIS, (represent dead band).

Heater switch on if tank temperature is below:  - 

[°C] 2 30 5



Tank Temperature: HIGH LIMIT.

When tank temperature reaches this value  alarm appears.

Put 0 to disable  alarm.

[°C] 0 95 75



Tank Temperature: LOW LIMIT.

During tank warm-up, temperature must increase at least  °C

otherwise

 warning appears.

Put 0 to disable  warning.

[°C] 0 10 1



Tank Filling Timeout.

If filling time is longer than ,  alarm appears.

Put 0 to disable  alarm.

[min] 0 42 20

DOC. NO. 5956.446.06 P. 11 / 114

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

To modify thresholds do the following:

• Switch OFF and switch ON the dishwasher;

• Enter into the FACTORY SETTING mode by pressing and hold down ON/OFF and CYCLE_2 keys for at

least five seconds

(Figure 33);

• Press CYCLE INFINITE. The display shows alternatively the symbol  (Figure 34) and the corre-

sponding value (Figure 35);

• Use CYCLE_1 key to decrease the value and CYCLE_2 key to increase (Figure 35);

• Press CYCLE INFITE key to confirm. The display shows the next parameter (Figure 36) and the corre-

sponding value (Figure 37);

• In the same way is possible to change the other parameters; when finished switch OFF and switch ON.

At the end the display will show again  and by pressing CYCLE_2 key (Fig. 41) is possible to change

cycle duration (see paragraph 7 CYCLE SETTING).

).

Fig.33 Factory setting

mode.

Fig.34 Boiler temp.

threshold

Fig.35 Change value &

Store

Fig.36 Boiler Temp

Hysteresis

Fig.37 Change value &

Store

Fig.38 Tank temp. High

limit.

Fig.39 Change value &

Store.

Fig.40 Factory setting

mode

Fig.41 Next Family Fig.42 Cycle 1 Family:

ENTER.

FAC btC

btH 76

°

2 bHi

bLo 96

FAC FAC

Cy1

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

DOC. NO. 5956.446.06 P. 12 / 114

7 CYCLE SETTING

IIn this paragraph is explained how to change cycle phases duration (see paragraph 7.1 CYCLE DIAGRAM).

• Switch on the dishwasher;

• Enter into the FACTORY SETTING mode: press and hold down ON/OFF and CYCLE_2 keys for at least 5

seconds

(Figure 43);

• Press CYCLE_2 key to select CYCLE_1 parameters.

• Press CYCLE_INFINITE. The display shows alternatively the symbol  (Figure 46) and the corre-

sponding value  (Figure 47);

• Use CYCLE_1 key to increase the value and CYCLE_2 key to decrease (Figure 47);

• Press CYCLE_INFINITE key to confirm. The display shows the next parameter (Figure 48) and the corre-

sponding value (Figure 49);

• In the same way is possible to change the other parameters;.

After settled all parameters referring Cycle 1, by pressing CYCLE_2 key is possible to change the Cycle 2

parameters

(Figure 50), (Figure 51) and so on.

Fig.43 Factory setting

mode.

Fig.44 Select next class. Fig.45 Cycle 1 Family:

ENTER.

Fig.46 Wash duration [min].

Fig.47 Change value &

Store

Fig.48 Wash duration [sec]. Fig.49 Wash duration

[min]..

Fig.50 Cycle 1 Parameters. Fig.51 Cycle 2 Parameters:

ENTER.

Fig.52 Wash duration [min].

Fig.53 Cycle 2 Parameters:

next Family

Fig.54 Cycle 3 Parameters:

ENTER

Fig.55 Wash duration [min].

FAC FAC

Cy1 Ln1

0 5h1

35

Cy1 Cy2

Ln2

…

Cy2 Cy3

Ln3

…

DOC. NO. 5956.446.06 P. 13 / 114

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

7.1 CYCLE DIAGRAM

CYCLE TYME

LEGENDA:

 = drain

 = wash  = rinse pause

 = pre rinse  = final pause

 = rrinse  = detergent

 = cold rinse  = rinse aid

IPA

Ln Sh

PA

Pr

ri

cr

FP

dr

rPA

dEt

rAi

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

DOC. NO. 5956.446.06 P. 14 / 114

7.2  Cycle 1 Parameters

7.3  Cycle 2 Parameters

7.4  Cycle 3 Parameters

7.5  Drain/Cleaning Cycle Parameters

Sym. Parameter Description Unit Min Max

Factory

Default



Wash Phase Long

[min] 0 20

0



Wash Phase Short

[s] 1 60

35



Pause

[s] 0 20

4



Pre-rinse Duration

[s] 0 30

0



Rinse Phase Duration

[s] 10 45

16



Cold Rinse Phase Duration

[s] 0 50

0



Drain

[s] 0 40

16



Final Pause at End of Cycle

[s] 0 60

0

Sym. Parameter Description Unit Min Max

Factory

Default



Wash Phase Long

[min] 0 20

0



Wash Phase Short

[s] 1 60

45



Pause

[s] 0 20

4



Pre-rinse Duration

[s] 0 30

0



Rinse Phase Duration

[s] 10 45

16



Cold Rinse Phase Duration

[s] 0 50

0



Drain

[s] 0 40

16



Final Pause at End of Cycle

[s] 0 60

0

Sym. Parameter Description Unit Min Max

Factory

Default



Wash Phase Long

[min] 0 20

1



Wash Phase Short

[s] 1 60

40



Pause

[s] 0 20

4



Pre-rinse Duration

[s] 0 30

0



Rinse Phase Duration

[s] 10 45

16



Cold Rinse Phase Duration

[s] 0 50

0



Drain

[s] 0 40

16



Final Pause at End of Cycle

[s] 0 60

0



Boiler Temperature Threshold: only for Cycle 3.

This parameter allows having a different rinsing temperature for

the third cycle. Only values above 45°C are allowed.

[°C] 0 95

0

Sym. Parameter Description Unit Min Max

Factory

Default



Initial Drain Phase Duration

[s] 0 240

40



Final Drain Phase Duration

[s] 0 240

60



Drain without cleaning cycle

- 0 1

0

DOC. NO. 5956.446.06 P. 15 / 114

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

8 OTHER PARAMETERS

8.1  Dishwashing Parameters

Note: ,, ,  parameters emulates a two levels pressure switch, keep in mind that value

doesn’t correspond to a physical quantity.

Sym. Parameter Description Unit Min Max

Factory

Default



Initial Pause before start washing (for ALL cycles)

[s] 0 10

0



Delay for the 2

nd

wash pump (PW only)

[s] 0 10

3



Active a drain phase at the end of washing phase.

[s] 0 40

0



Duration of pause after rinse cycle (valid for dishwashers with

door/hood lock device) [See par.

9.2 MEDICAL LINE

DISHWASHER WITH DOOR/HOOD LOCK DEVICE].

[s] 0 60

0



Celsius/Fahrenheit selection

0 = Celsius

1 = Fahrenheit

- 0 1

0



Rinse Temperature Display.

Enable rinse temperature probe (if installed).

0 = during rinse phase the display shows boiler temperature;

1 = during rinse phase the display shows rinse temperature;

- 0 1

0



Pulse Per Litre.

This parameter must be settled in according to flow meter

installed [present up to software version 3.12].

[p/l] 0 255

0



Number of wash cycles performable without detergent (only for

dishwashers with external detergent level sensor – par.

9.3

DETERGENT AND RINSE AID LEVEL SENSORS ACTIVATION)

[]

- 0 5

5



Pressure sensor threshold 1 [present up to software version 2.11].

- 0 255

140



Pressure sensor histeresis 1 [present up to software version 2.11].

- 0 255

50



Pressure sensor threshold 2 [present up to software version 2.11].

- 0 255

140



Pressure sensor histeresis 2 [present up to software version 2.11].

- 0 255

50

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

DOC. NO. 5956.446.06 P. 16 / 114

8.2  Read Only Parameters

8.3  Communication and HACCP Parameters

Sym. Parameter Description Unit Min Max

Factory

Default



Main Board Firmware Release

- - - -



Water softener board software version. (only for dishwashers with

incorporated continuous water softener).

- - - -



Active column: indicates through which of the two continuous

water softener columns boiler filling is being carried out: 0 = col

-

umn A and 1 = column B (only for dishwashers with incorporated

continuous water softener).

- - - -



When



message appears, the parameter value becomes 3.

After maintenance, to clear  message, insert 0.

- - - -



When   alarm appears, the machine is frozen and this

parameter is 3.

After maintenance (see alarm codes document), insert 0 to ena-

ble the machine.

- - - -



This alarm appears in case of malfunctioning in the continuous

water softener. To facilitate fault-finding, see par.

13.3 ALARMS

THAT DON’T STOP THE DISHWASHER FOR MODELS WITH

INCORPORATED CONTINUOUS WATER SOFTENER.

- - - -

Sym. Parameter Description Unit Min Max

Factory

Default



Serial Device

0 = 8N1

1 = PC connection (DAAS 8E1)

7 = HACCP network (ECAP 8E1+LK485) (LK485 board is nec-

essary)

9 = Dishwashers with incorporated continuous water softener

11 = Machines with incorporated continuous water softener that

communicate with LK485 board

16 = HACCP printer (8N1)

32 = MODEM GSM (DAAS 8N1)

33 = MODEM GSM (DAAS 8E1)

48 = Hyper Terminal (8N1)

- 0 63

1



Address.

This parameter specifies the address of the appliance into the

‘HACCP_network’.

Works only if ‘HACCP network’ is selected (see above parameter).

- 0 255

1



Print parameter table.

- 0 1

1



HACCP ‘Basic’ (printer)

Boiler temperature: high limit.

[°C] 45 95

90



HACCP ‘Basic’ (printer)

Boiler temperature: gap below high limit.

[°C] 0 20

10



HACCP ‘Basic’ (printer)

Tank temperature: high limit.

[°C] 35 75

68



HACCP ‘Basic’ (printer)

Tank temperature: gap below high limit.

[°C] 0 20

10

DOC. NO. 5956.446.06 P. 17 / 114

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

8.4  Configuration Parameters

Sym. Parameter Description Unit Min Max

Factory

Default



Dishwasher Model:

0 = HOOD TYPE & UNDERCOUNTER

1 = POT WASHER

2 = AUTOMATIC POT WASHER

3 = MEDICAL LINE DISHWASHER WITH LOCK DOOR/HOOD

DEVICE

- 0 3

0



Boiler type:

0 = ATMOSPHERIC BOILER

1 = PRESSURE BOILER

2 = EXTERNAL BOILER

- 0 2

0



Door type:

0 = AUTOMATIC HOOD

1 = MANUAL HOOD

2 = FRONT LOADING

3 = POT WASHER

0 3

1



Default model (see Default tables):

1 = HOOD TYPE

2 = POT WASHER

3 = UNDERCOUNTER

- 0 3

-



Solid State Relay (TRIAC).

0 = not enabled;

1 = SOFT START enabled;

3 = SLOW SOFT START enabled

(works only on boards with Solid State Relay).

- 0 3

0



Boiler/Tank heating swap:

0 = boiler heaters and tank heater can work simultaneously;

1 = swap enabled: tank heating starts only boiler temperature is

reached;

(Note: disabling this function changes the global electrical power

of appliance; before enabling this function check available power,

supply cable section, fuses in according to User Manual).

- 0 1

1



Tank Filling Mode

Enable filling tank by means of rinsing cycles.

Ex:  = 75 means that boiler water is heated at 75°C, then

follows a rinse phase and so on until tank is full.

If  = 0 the tank is filled by solenoid valve in the traditional

way (On machines with incorporated continuous water softener,

even if

 is set to 0, filling occurs through subsequent rinses).

[°C] 0 85

75



Detergent Level Switches

0 = level switches not enabled;

1 = enable detergent level switches;

- 0 1

0



USER INTERFACE MODEL

8 = ACTIVE function disabled (up to version 3.11 [up to serial

nr. 42100099] set to 0)

9 = hood type, under counter (up to version 3.11 [up to serial

nr. 42100099] set to 1)

13 = LS5 with atmospheric boiler(up to version 3.11 [up to

serial nr. 42100099] set to 5)

15 = LS5 with pressure boiler (user interface without display); (up

to version 3.11 [up to serial nr. 42100099] set to 7)

24 = LS5 with atmospheric boiler (From Ser. Nr.: 821).

See parameter (family ) to check the software ver-

sion installed in the board.

- 0 15

9

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

DOC. NO. 5956.446.06 P. 18 / 114

8.5  Parameters for automatic hood type dishwashers



Enable “regeneration cycle” key (only for dishwashers with non-

continuous water softener) [See paragraph

9.1 RESIN REGENE-

RATION CYCLE].

- 0 1

0



ALARMS ENABLE

0 = alarms disabled (to disable also warnings see  and

);

1 = alarms enabled;

If this function is disabled, faults can be detected so display do

not shows any alarm code.

- 0 1

1



Air gap with float level sensor normally closed (the level sensor is

closed when the boiler is empty). E.g. the boiler level sensor for

machines with incorporated continuous water softener.

- 0 1

0



Forced start of a resin regeneration cycle (only for dishwashers

with incorporated continuous water softener). [See paragraph

9.4

DISHWASHER WITH INCORPORATED CONTINUOUS WATER

SOFTENER].

- 0 2

0



Max. rinse water hardness (only for dishwashers with incorpo-

rated continuous water softener). After modifying, disconnect and

reconnect the machine's main power supply by means of the

main switch. [See paragraph

9.4 DISHWASHER WITH INCOR-

PORATED CONTINUOUS WATER SOFTENER].

°fH 4 14

10



Boiler heating control.

Defines the max. permissible temperature difference during boiler

heating in a time interval of 2 minutes and 30 seconds.

°C 25 80

50

Sym. Parameter Description Unit Min Max

Factory

Default



DELAY_K1

Time (during hood lifting) within which S3” must return to the rest

position.

0.1 s 0.0 s. 20.0 s

15



HOOD_TOUT

TIMEOUT – max. time allowed for complete hood opening/clos-

ing.

0.1 s 0.0 s 20.0 s

200



DELAY_K1_S3

During hood lowering, firstly S3” must cut in and then after a time

 .the bottom limit switch S3.

0.1 s 0.0 s. 20.0 s 15



DELAY_K

Time within which K and K’ must be both closed or both open.

0.1 s 0.0 s. 20.0 s 10



DELAY_S3

Time during hood lifting within which the bottom limit switch must

return to the rest position..

0.1 s 0.0 s. 20.0 s 20



DELAY_S5

Time during hood lowering within which the top limit switch must

return to the rest position.

0.1 s 0.0 s. 20.0 s 20



Displays the last alarm code relative to automatic hood type dish-

washers.

- - - 0



Parameter only valid for hood type models.

Hood lifting motor absorption threshold.

(50 units correspond to a current of approx. 1 ampere).

- 0 250 100

DOC. NO. 5956.446.06 P. 19 / 114

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

9 SPECIAL FEATURES

9.1 RESIN REGENERATION CYCLE

The regeneration cycle is activated by pressing the button shown in the figure, for at least 5 seconds.

For this key to be enabled parameter (in family ) must be set to 1.

At this point you can enter the number of wash cycles that can be performed after each regeneration: param-

eter  in the counters family . If  is set to zero the counter is disabled, otherwise after the pre-

set number of cycles the message  is displayed to confirm that regeneration is possible (this is an

information-only message with no effect on operation of the appliance, so you can continue to use the dish

-

washer). The message is cleared when the regeneration cycle is terminated.

The number of regeneration cycles performed can be checked by consulting the parameter  in the 

family of counters.

When there are just 15 cycles remaining before the next regeneration cycle, at the end of the wash cycle the

display shows the message

 followed by , at the end of the next wash cycle the display shows 

and , and so forth, i.e. the display informs the user of the number of wash cycles still available before resin

regeneration is required.

Before starting the regeneration cycle remove the siphon spillway.

WARNING:

If the regeneration cycle is accidentally started, it can be switched off by pressing the button shown in

the figure, for at least 5 seconds

The hardness of the water exiting the softener can vary between 3°fH - 10 °fH / 1.7 °dH - 5.6 °dH / 2.1 °cH - 7

°cH.

9.2 MEDICAL LINE DISHWASHER WITH DOOR/HOOD LOCK DEVICE

The medical line dishwasher with door/hood lock device has a device that prevents door/hood opening for the

entire duration of the work cycle.

For the door/hood lock to be active, the parameter (in the  family) must be set to .

The dishwasher door/hood is locked at the start of a wash cycle and is released at the end of the final pause

after rinse. The wash compartment can be accessed by stopping the work cycle in progress, as the locking

device is thus disabled. .

A pause at the end of rinse can be set by means of the parameter  (in the  family). This parameter

is common to all 3 wash cycles. The rinse water temperature is displayed during this pause. Another final

pause in the cycle can be set by setting the parameters

, , . During the final pause the display

shows the time remaining for completion of the cycle. The door/hood lock device will be deactivated at the end

of the final pause (

, , ).

For correct performance of the wash cycle the pause at the end of rinse and the final pause must assume the

default values (see Prog 032 – 034 - 035).

9.3 DETERGENT AND RINSE AID LEVEL SENSORS ACTIVATION

By setting the parameter (in the  family) to 1, management of the level sensors located inside the

external detergent and rinse aid tanks is enabled. During the rinse phase, when the rinse aid inside the tank

has finished, the message

appears on the display.

TANK

BOILER

Electrolux

EFS - Dishwashing Systems Platform

Electrolux Professional

DOC. NO. 5956.446.06 P. 20 / 114

When the detergent inside the tank is finished, the message   is displayed and after a number of

wash cycles equal to

 (in the  family) the dishwasher inhibits the activation of other wash cycles.

Therefore the detergent level in the tank must be restored.

9.4 DISHWASHER WITH INCORPORATED CONTINUOUS WATER SOFTENER

Dishwashers with incorporated continuous water softener have a continuous softener in the water circuit. By

means of special resins, this device removes the calcareous substances from the feed water, supplying decal

-

cified water for washing.

To activate the continuous water softener, set the parameter  (in the  family) to the value  or the

value

 if the water softener board is connected to the LK485 board.

For the continuous softener to work properly the resins must be regenerated periodically with a frequency

depending on the hardness of the inlet water, the number of wash cycles carried out and the max. hardness

set with the parameter

 (in the  family).

Unlike conventional water softeners, this continuous softener does not require machine stops for regenerating

the resins.

To regenerate the resins it is necessary to put coarse salt in the special container located in the dishwasher.

In particular, the salt container must be filled when the dishwasher is used for the first time and whenever the

messages

 or  are displayed at the start or end of a wash cycle. The salt container holds

up to 1.5 kg of salt

WARNING:

Use only coarse salt with a NaCl purity grade of 99.8 %. The use of salt with a lower purity grade may

cause the sale container filter to clog and the water softener to malfunction.

WARNING:

The messages  or may appear for several wash cycles even after topping-up the

salt, as the salt must circulate in the entire system. Correct operation of the dishwasher is not, how

-

ever, affected

The number of regeneration cycles performed can be checked by consulting the parameter  in the 

family of counters.

 only counts regeneration cycles carried out with the salt container adequately filled; there is another

counter,

(in the  family) that indicates the number of regeneration cycles done without salt.

If the parameter SrU is set to the value10, according to the factory setting, the water softener outlet water

hardness can vary between 3°fH - 10 °fH/ 1.7 °dH - 5.6 °dH / 2.1 °cH - 7 ° cH.

AUTONOMY OF A COLUMN OF RESINS ACCORDING TO THE CHANGE IN INLET WATER HARDNESS,

WITH OUTLET WATER HARDNESS OF 10 °fH / 5.6 °dH /7 °cH (

according to the factory

setting).

Maximum outlet water hardness can be modified by setting the  value. The outlet water hardness can be

modified from the value of 4° fH to 14° fH.

°fH °dH °cH Number of cycles

15 8,4 10,5 14

20 11,2 14 10

25 14 17,5 7

30 16,8 21,1 6

35 19,6 24,6 5

40 22,4 28,1 4

Page is loading ...

Electrolux WT830M240U User manual

Electrolux WT830M240U User manual

Related papers

Other documents