Haier HLC32 User manual

Please READ this manual carefully before

operating your TV, and retain it for future

reference.

TFT-LCD TV/DVD Combo

OWNER S MANUAL'

MODEL :

S

HLC26

HLC32

A

2 TV LCD-TFT

THIS SYMBOL INDICATES THAT HIGH VOLTAGE IS PRESENT

INSIDE. IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT

WITH ANY INSIDE PART OF THIS PRODUCT.

WARNING : To reduce the risk of electric shock do not remove cover or back.

No user-serviceable parts inside refer service to qualified service personnel.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, use and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to

try to correct the interference by one or more of the following measures:

*Reorient or relocate the receiving antenna.

*Increase the separation between the equipment and receiver.

*Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

*Consult the dealer or an experienced radio/TV technician for help.

This device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may be not cause harmful interference.

(2) this device must accept any interference received, including interference that may cause undesired

operation.

FCC CAUTION:

To assure continued compliance and possible undesirable interference, the provided ferrite cores must be

used when connecting this display to video equipment; and maintain at least 40cm spacing to other

peripheral device.

CANADIAN NOTICE:

This Class B digital apparatus compiles with Canadian ICES-003.

However there is no

guarantee that interference will not occur in particular installation

LCD

RISK ELECTRIC SHOCK

DO NOT OPEN

WARNING

Operator Safety has been taken into consideration at the design and manufacture phase, but inappropriate operation may

cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the

installation, use and maintenanceof th product. Read the following safety instruction before starting the operation.

The User Manual uses the following symbols to ensure a safe operation and prevent any damage to operators

or properties:

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT

OPERATING AND MAINTENANCE INSTRUCTIONS IN THE

LITERATURE ACCOMPANYING THE APPLIANCE.

FCC STATEMENT

Warning

Owner s Manual 3

IMPORTANT SAFETY INSTRUCTIONS

Read all of the instructions before using this appliance. When using this

appliance, always exercise basic safety precautions, including the following:

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer`s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of

time.

14) Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15) WARNING-To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,

shall be placed on the apparatus.

The apparatus shall not be exposed to dripping or splashing and that no objects filled

with liquids, such as vases, shall be placed on the apparatus.

The mains plug is used as the disconnect device, remain it readily operable during the

apparatus normal use.

S3126A

PORTABLE CART WARNING

(symbol provided by RETAC)

Safety Instructions

SAVE THESE INSTRUCTIONS

Thank you for purchasing the Haier product. This easy-to-use manual will guide you in getting the best use of your

product. Remember to record the model and serial number. They are on label in back of the unit.

Model number

serial number

Date of purchase

Staple your receipt to your manual. You will need it to obtain warranty service.

4 TV LCD-TFT

Safety Instructions

Introduction

Owner s Manual 5

War ning . . . . . . . ..... .... .... . . . . . . . . . . . . . . . . . . . . . .

Safe ty Ins truc tion s . . . . . . . . . . . . . . . . . . . . . . . . . . .

Introduction

Cont rols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... .... .

Conn ecti on Opt ions . . . . . . . . . . . . . . . . . . . . . . .... ....

Universal Remote Control . ............ . . . . . . . . ........

Installation

Acce ssor ies . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .... ..

Antenna Connection . . . . . . . . . . ..........................

VCR Connection. . . . . . . . . . . . . . . . . . . . . ..............

External A/V Source Setup . . . . .. . . . . ..................

DVD Connection . . . . . ...... . . . . . . . . . . . . . ...........

DTV Connection..................................................

Digital Audio Output . . . . . . . . . . . . . . . . . . . . ...........

PC Connection. . . . . . . . . . . . . . . . . . . . . . . .............

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... .... .... ..

Cable sample.....................................................

Connecting Headphones . . . . . . . . . . . . . . . . . . . .....

Power source................ . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . .

Operation

Switching On/Off the TV set . . . . . ... . . . . . . . . . . ....

Choose the Menu Language . . . . ..... ...................

Choose the input source......................................

Channel Menu

Auto mati c Scan . . . . .... ... . . . . . . . . . . . . . . . . . . . . .. .

Add Channel Scan............... . . . . . . . . . . . . . . . . . . .

Rena me ... .... .... ... . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . .. . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Video Menu

Audio Menu

SAP Broadcasts Setup.........................................

Take the table stand off

Select the desired program

Select the desired sound

Mute

How to select picture mode..................................

How to customize your own picture status .............

How to select audio mode.....................................

How to customize your own audio status ...............

Time Menu

Date /Time setting................................................

Time zone setting.................................................

Sleep Timer setting..............................................

Timer on setting...................................................

Timer off setting...................................................

Function Menu

Menu Language...................................................

DTV Caption Style...............................................

OSD Timeout.......................................................

OSD Transparency...............................................

DNR...................................................................

Adjust Menu

Screen Setup for Component or PC mode..............

Lock Menu

Parental Control rating and categories...................

Lock setup...........................................................

Other Functions

Brie f Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... .... ....

Quick program view.............................................

Aspect Ratio Control . . . . . . . . . . . . . . . . . . . . .. . . .. . .

CC (Closed Caption Display) . . . . . . . . . . . . . ... . .. .

Remote Control

Setting up your remote control .............................

Remote Control Codes ........................................

DVD Operation

Basic Playback......................................................

Advanced Playback...............................................

Special Function Playback.....................................

DVD System Setup.................................................

Playable Discs......................................................

Discs Protection and DVD Characteristics..............

Maintenance . . .. .... . . . . . . . . . . . . . . . . . . . . . . . . . .

Product Specifications . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . ..

Warranty ...........................................................

2

3

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

32

33

34

36

40

41

42

43

46

47

48

49

50

51

Contents

Front panel controls

This is a simplified representation of front panel.

Here shown may be somewhat different from your TV.

Introduction

6 TV LCD-TFT

Controls

VIDEO

AUDIO

AV3 AUDIO Input

connect to hear

stereo sound from an

external device.

AV3 VIDEO Input

Connects the video signal

from a video device.

Earphone jack

Earphone audio

output terminal.

R

L

1

INPUT

2

3

4

5

MENU

CH+

VOL+

HLC26 HLC32

POWER

CH-

VOL-

1.INPUT: Press to show the input source mode. In the MENU/INPUT screen,

these buttons serve as OK buttons.

2.CH : Press to scan through channels. To scan quickly through channels,

press and hold down either +/- . In the MENU screen, these buttons

serve as up/down buttons.

3.VOL : Press to adjust the volume .In the MENU screen, these buttons

serve as left/right buttons.

4.MENU: Menu display.

5.POWER: Press to turn on and off the TV.

-/+

A A

Label Towards Back

OPEN/CLOSE

STOP

PLAY/PAUSE

OPEN/CLOSE

PLAY/PAUSE

STOP

The Tray

OPEN/CLOSE:

Press to open the disc tray, and press again to close the tray.

Press to play the DVD program, and press again to pause the DVD program.

STOP

Press to stop the DVD program.

Press to play the previous program.

PLAY/PAUSE

HDMI/DVI IN 1 HDMI/DVI IN 2

PC IN

AC IN

VIDEO

Pr

Pb

Y

Pr

Pb

Y

OPTICAL

PC/DVI

AUDIO IN

L R

AUDIO

S-VIDEO

ANT IN

COMPONENT IN

AV IN

Video

L R

Video

L R

Back panel controls

Introduction

Owner s Manual 7

Connection Options

Power Cord Socket

This TV operates on AC power.

The voltage is indicated on the

Specifications page. Never attempt

to operate the TV on DC power.

Antenna Input

Connect cable or

antenna signals to

the TV, either directly

or through your

cable box.

S-Video Input

Connect S-Video

out from an S-VIDEO

device to the

S-VIDEO input.

Digital Audio Output

Connect digital audio from

various types of equipment.

Note: In standby mode,

these ports will not work.

PC/DVI Audio Input

Connect the audio out from

the external device, used

while linking PC audio

frequency output terminals

or using a DVI to HDMI

connector.

DVD/DTV Input

(Component )

Connect a component

video device to these

jacks.

PC VIDEO Input

Connect the monitor

output connector from

a PC to the jack

HDMI

connect a

signal to

HDMI/DVI.

COMPONENT AUDIO Input

connect to hear

stereo sound from an

external device.

VIDEO Input

Connects the video

signal from a

video device.

AUDIO Input

connect to hear

stereo sound from an

external device.

HLC26 HLC32

A A

TV/DVD

PROGRAM

SLOW

CC

CH.LIST

SETUP

ANGLE

SEARCH

A

U

DIO

SUBTITLE

REPEAT

SUBTITLE

D.MENU

P

.MO

D

E

S.M

OD

E

D

.C

ALL

FREEZE

E

N

U

INFO

E

X

IT

R

A

C

S

A

P

S

L

E

P

VOL+

CH+

10+

Q.VIEW

OK

VO

L

-

CH-

POWER

Press to turn on and off the TV.

The remote control cannot be operated unless the batteries are properly loaded.

When using the remote control, aim it at the remote control sensor on the TV.

Note: For DVD function see page 41.

Function introduction

SAP

Selects MTS sound: Mono, Stereo, and

SAP in Analog mode. Change the audio

language in DTV mode.

Introduction

THUMBSTICK

(Up/Down/Left/Right/OK)

Allows you to navigate the on-screen

menus and adjust the system settings to

your preference.

CHANNEL UP/DOWN

Press to scan through channels. To scan

quickly through channels, press and hold

down either +/- .

P.MODE

Selects the picture mode appropriate

for the program's character.

FREEZE

Freezes the currently-viewed picture, but

audio continues. Press FREEZE button

again to resume the normal picture.

ARC

(Aspect Ratio Control)

Changes the aspect ratio.

S.MODE

Selects the sound mode appropriate

for the program's character.

VOLUME UP/DOWN

Press to adjust the volume.

Numeric buttons

Press to change the channel.

EXIT

Clears all on-screen displays and

returns toTV viewing from any menu.

INPUT

show the input source mode.

MUTE

Switches the sound on or off

CC(closed caption)

Select a closed caption

TIME

Shows time.

INFO

When you watch the TV, press the key,

the information displays on top of

the screen.

MENU

Brings up the main menu to the screen.

SLEEP button

Displays the Sleep Timer option.

Q.VIEW

Switch the current channel to the last

channel you have viewed.

TV/DVD

Press to enter TV/DVD signal

TV DVD VCR SETBOX CABLE AUDIO

Press the SELECT button repeatedly to select

one of the system modes in which the remote

control can be used. When the desired device is

selected, the corresponding LED lights on 5 seconds.

VCR/DVD Functions

Control some video cassette recorders or

DVD players.

Open/close

/ Rewind / Fast

/ backward /Forward

Stop

Play

/ Play/Pause/REC

- button

Press to select additional channels

(digital )

being broadcast by the same station.

For example, to select channel

“54-3”, press “54”, then press

“-” and “3”.

CH.LIST

Open the channel list.

A-B

SELECT

TITLE/PBC

ZOOM

Universal Remote Control

8 TV LCD-TFT

TIME

INPUT

TV/DVD

PROGRAM

SLOW

CC

CH.LIST

SETUP

ANGLE

SEARCH

A

U

D

I

O

SUBTITLE

REPEAT

SUBTITLE

D.MENU

P

.

M

ODE

S

.

M

O

D

E

D

.

C

A

L

FREEZE

EN

U

IN

F

O

E

X

I

T

R

A

C

S

A

P

S

L

E

P

VOL+

CH+

10+

Q.VIEW

OK

VO

L

-

CH-

A-B

SELECT

TITLE/PBC

ZOOM

TIME

INPUT

AV IN

Video

L R

Video

L R

S-VIDEO

ANT IN

Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an

outdoor antenna .

.

Over-the-air TV reception quality will depend on your antenna type, antenna

location and antenna positioning

External Equipment Connections

Antenna Connection

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

Wall Antenna

Socket

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

Outdoor

Antenna

VHF Antenna

UHF Antenna

Turn clockwise to tighten

RF Coaxial Wire (75 ohm)

Bronze Wire

Be careful not to bend the bronze wire

when connecting the antenna.

Bronze Wire

To improve the picture quality in a poor signal area,

please purchase a signal amplifier and install properly.

If the antenna needs to be split for two TV`s, install

a 2-Way Signal Splitter in the connections.

To install the antenna properly please contact a

professional in your area.

Installation

Accessories

Remote control

Owner`s manual

Alkaline battery(AAA) 2

Power cable

Owner s Manual 9

Please READ this manual carefully before

operating your TV, and retain it for future

reference.

TFT-LCD TV/DVD Combo

OWNER S MANUAL'

MODEL :

S

HLC26

HLC32

A

L R

AUDIO

S-VIDEO

ANT IN

AV IN

Video

L R

Video

L R

VCR connection

NOTE: All cables shown are not included with the TV.

There are several ways to connect your television, depending on the components you want to connect

and the quality of the signal you want to achieve. The following are examples of some different ways

to connect your TV with different input sources.

External Equipment Connections

Choose Your Connection

To avoid picture noise (interference), leave an adequate distance between the VCR and TV

Connection Option 1

Set VCR output switch to channel 3 or 4 and

then tune the TV to the same channel number.

Connection Option 2

1. Connect the audio and video cables from the

VCR's output jacks to the TV input jacks, as

shown in the figure.

When connecting the TV to VCR, match the

jack colors (Video = yellow, Audio Left = white,

and Audio Right = red).

If you connect an S-VIDEO output from VCR to

the S-VIDEO input, the picture quality is

improved; compared to connecting a regular

VCR to the Video input.

2. Insert a video tape into the VCR and press

PLAY on the VCR. (Refer to the VCR owner`s

manual.)

3. Select the input source with using the

INPUT button on the remote control, and

then press / button to select the source,

press theOK button to confirm.

Installation

10 TV LCD-TFT

VIDEO

Pr

Pb

Y

Pr

Pb

Y

OPTICAL

PC/DVI

AUDIO IN

L R

AUDIO

S-VIDEO

COMPONENT IN

AV IN

Video

L R

Video

L R

AUDIO

S-VIDEO

ANT IN

AV IN

Video

L R

Video

L R

How to connect

1. Connect the DVD video outputs (COMPONENT) to

the Y Pb Pr jacks on the TV and connect the DVD audio

outputs to the Y Pb Pr Audio IN jacks on the TV, as

shown in the figure.

2. If your DVD only has an S-VIDEO output jack,

connect this to the S-VIDEO input on the TV. as shown

in the figure.

Note

If your DVD player does not have component video

output, use S-Video.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the INPUT button on the remote control to select

Y Pb Pr mode.

3. Press Play button on external equipment for program

play.

4. Refer to the DVD player's manual for operating

instructions.

External Equipment Connections

How to connect

Connect the audio and video cables from the external

equipment's output jacks to the TV input jacks, as shown

in the figure. When connecting the TV to external equipment,

match the jack colors (Video = yellow, Audio Left = white,

and Audio Right = red).

How to use

1. Select the input source with using the INPUT button on

the remote control.

2. Press the / button to select the desired source.

3. Press the OK button to confirm.

4. Operate the corresponding external equipment.

Video Game Set

Camcorder

Component Input ports

To get better picture quality, connect a DVD player to the

component input ports as shown below.

Installation

Component ports

on the TV

Video output ports

on DVD player

Y Pb Pr

Y B-Y R-Y

Y Cb Cr

Y P P

BR

Note

The audio input terminal of AV IN 1 is compared with S-VIDEO.

External A/V Source Setup

DVD connection

Owner s Manual 11

DVD

or

OPTICAL

L R

AUDIO

L R

HDMI/DVI IN 2

PC IN

VIDEO

Pr

Pb

Y

Pr

Pb

Y

OPTICAL

PC/DVI

AUDIO IN

L R

AUDIO

COMPONENT IN

L R

Digital Set-top Box

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do

receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,

1080i).

How to connect

Use the TV`s COMPONENT , PC or HDMI/DVI

jack for video connections, depending on

your set-top box connector. Then, make

the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the

owner`s manual for the digital set-top box.)

2. Use INPUT on the remote control to select

COMPONENT , PC or HDMI/DVI source.

Send the TV`s audio to external audio equipment (stereo system) via

the Digital Audio Output (Optical) port.

How to connect

1. Connect one end of an optical cable to the TV Digital Audio

(Optical) Output port.

2. Connect the other end of the optical cable to the digital audio (optical)

input on the audio equipment.

See the external audio equipment instruction manual for operation.

Note

When connecting with external audio equipments, such as amplifers or

speakers, please turn the TV speakers off.

Digital Audio Output

Caution: Do not look into the optical output port.

Looking at the laser beam may damage

your vision.

External Equipment Connections

DTV connection

Installation

Signal

480i

480p

720p

1080i

COMPONENT

HDMI/DVI

Yes

HDMI

12 TV LCD-TFT

HDMI/DVI IN 1 HDMI/DVI IN 2

PC IN

VIDEO

Pr

Pb

Y

Pr

Pb

Y

PC/DVI

AUDIO IN

How to connect

1. To get the best picture quality, adjust the PC graphics card to 1024

2. Use the TV`s PC or DVI (Digital Visual Interface)Audio IN port for video connections, depending on your PC

connector.

If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either PC

r HDMI/DVI IN to display the PC on the TV.

If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to eithe

DVI; (the other mode is set to Plug and Play automatically by the TV.)

3. Then, make the corresponding audio connection. If using a sound card, adjust the PC sound as required.

How to use

1. Turn on the PC and the TV.

2. Turn on the display by pressing the POWER button on the TV's remote control.

3. Use INPUT on the remote control to select PC or HDMI/DVI source.

4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or

brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC

graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

Note

1.Use a DVI cable.

2.Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently

imprinted on the screen.

3. The synchronization input form for Horizontal and Vertical frequencies is separate.

x768 .

IN o

r PC or

HDMI/

Resolution

Frame

frequency

(Hz)

VGA

SVGA

XGA

640*480

60Hz

800*600 60Hz/75Hz

1024*768

60Hz

Mode

Resolution

External Equipment Connections

Installation

75Hz

PC connection

Owner s Manual 13

When the source device(DVD player or Set Top Box) supports HDMI

How To Connect

1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product).

2. No separated audio connection is necessary.

How To Use

If the source device supports Auto HDMI function, the output resolution of the source device will be automatically

set to 1280x720p.

If the source device does not support Auto HDMI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

Select HDMI input source in input source option of Select Main source menu.

When the source device(DVD player or Set Top Box) supports DVI

How To Connect

1. Connect the source device to HDMI port of this TV with a HDMI-to-DVI cable(not supplied with this product).

2. A separated audio connection is necessary.

3. If the source device has an analog audio output connector, connect the source device audio output to DVI Audio

In port located on the left side of HDMI port.

How To Use

If the source device supports Auto DVI function, the output resolution of the source device will be automatically set

to 1280x720p.

If the source device does not support Auto DVI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

Press the INPUT button to select HDMI input source in input source option of Select Main source menu.

Installation

HDMI

14 TV LCD-TFT

HDMI Cable

(not supplied with the product)

HDMI to DVI Cable

(not supplied with the product)

Analog Audio Cable

(Stereo to RCA type)

(not supplied with the product)

Installation

Cable sample

Owner s Manual 15

VIDEO

AUDIO-R

AUDIO- L

Power source

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for

operation on AC. Insert the AC cord plug into

a standard polarized AC outlet.

Note

Never connect the AC line cord plug to other

than the specified voltage. Use the attached

power cord only.

If the polarized AC cord does not fit into a non-

polarized AC outlet, do not attempt to file or cut

the blade. It is the user`s responsibility to have

an electrician replace the obsolete outlet.

If you cause a static discharge when touching

the unit and the unit fails to function, simply

unplug the unit from the AC outlet and plug it back

in. The unit should return to normal operation.

Polarized AC Cord Plug

AC Outlet

Wider Hole

and Blade

You can connect a set of headphones to your set if you wish to watch a

TV programme without disturbing the other people in the room.

Connecting Headphones

Note

Prolonged use of headphones at a high volume

may damage your hearing.

You will not receive sound from the speakers

when you connect headphones to the system.

Plug a set of headphones into the 3.5mm

mini-jack socket on the side panel of the set.

Installation

External Equipment Connections

16 TV LCD-TFT

Installation

You can take off the table stand if you don`t want to use the table stand.

Take the table stand off

Please release the screws 6XM4,

see the picture.

HLC26 HLC32

A

Owner s Manual 17

Choose the Menu Language

When you start using your set for the first time, you must select the language which will be used for displaying menus

and indications.

In the manual, the OSD (on screen display) may be different from your TV`s, because it is just an example to help

you with the TV operation.

There are several options you might need to set up in order for your TV to work properly. Read the instructions that

follow.

Note

If the TV in power on , the screen show information according the type of input signal . the information will disappear.

If there is no signal , No Signal will display on the screen.

1 Choose the TV Input and then Press the MENU button.

2 Press the / button to select the Function menu.

3 Press the or OK button and then select the Menu

Language.

4 Press the or OK button to select language.

English Spanish or French

5 When you are satisfied with your choice, press the EXIT button

to return to normal viewing or press the MENU button to return to

the previous menu.

1. First, connect power cord correctly.

2. Select the viewing source by using INPUT button on the remote control.

3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.

4. If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

Change the picture source so you can watch your TV, cable TV, VCR, DVD, or any

other devices that are connected to your TV.

1. Press the INPUT button to enter the Select Main picture Source menu

and then use the / button to select the desired items TV, V , V ,

S-Video,Component1, Component2, In DVD ,PC, HDMI/DVI1, HDMI/DVI2 .

2. Press the OK button to confirm .

ideo1 ideo2

Video3,

Operation

Channel

Video

Audio

Time

Lock

Function

Menu Language English

DTV Caption Style

OSD Timeout Middle

OSD Transparency Middle

DNR Off

Move /OK: Select /EXIT/ MENU: Exit

Select Source

TV

Video1

Video2

Video3

S-Video

Component1

Component2

In DVD

PC

HDMI/DVI1

HDMI/DVI2

Operation

Switching On/Off the TV set

Choose the Input source

18 TV LCD-TFT

Move /OK: Select /EXIT/ MENU: Exit

This TV set has two methods to set channels, which are respectively Auto Scan, Add Channel Scan.

In this section, how to use the remote control to set channel is explained. You can also use buttons on the TV

set to set channel.

Automatic Scan

Note

The Channel menu will be only operated in normal TV mode.

Channel menu

Automatically finds all channels available through antenna or cable inputs, and

stores them in memory on the All Channel List.

Operation

Video

Audio

Time

Lock

Function

Channel

Tuner Antenna

Auto Scan

Add Channel Scan

Rename

NTSC Channel 55

Analog channels 19

Digital Channels 0

Progress(%)64

Auto Scan

1 Press the MENU button and then select the Channel menu.

2 Press the or OK button and then use / button to select Tuner.

3 Press the or OK button Select Cable or Antenna mode.

4 Press the / button to select Auto Scan.

5 Press the or OK button to start searching.

6 To cancel searching, press the EXIT /MENU button.

Note

When Antenna is selected, the TV will detect antenna signals

andwill search for antenna TV (NTSC and ATSC) channels

available in your local area.

When Cable is selected, the TV will detect cable company

supplied signals and will search for cable TV (NTSC,QAM

modulated) channels available in your area.

The Auto Scan function search for NTSC program first and then

search for ATSC or QAM program.

Owner s Manual 19

Move /OK: Select /EXIT/ MENU: Exit

Channel menu

Add Channel Scan

Rename

1 Press the MENU button and then select the Channel menu.

2 Press the or OK button and then use / button to select

Rename.

3 Press the or OK button to enter the Submenu.

4 press / button to move the cursor and then use / button

to change.

5 When you are satisfied with your choice, press OK button to

return to the previous menu or Press EXIT button to return to

TV viewing.

Operation

Video

Audio

Time

Lock

Function

Channel

Tuner Antenna

Auto Scan

Add Channel Scan

Rename

Add Channel Scan

NTSC Channel 55

Analog channels 19

Digital Channels 0

Progress(%)64

Video

Audio

Time

Lock

Function

Channel

Tuner Antenna

Auto Scan

Add Channel Scan

Rename

1 Press the MENU button and then select the Channel menu.

2 Press the or OK button and then use / button to select

Tuner.

3 Press the or OK button Select Cable or Antenna mode.

4 Press the / button to select .

5 Press the or OK button to start searching.

6 To cancel searching, press the EXIT/MENU button.

Add Channel Scan

Ch 16-0

Move Change EXIT: Exit

Rename

- - - - - - -

Only search the new channel ,so the old channel will not be cleared.

Note

When Antenna is selected, the TV will detect antenna signals

and will search for antenna TV (NTSC and ATSC) channels

available in your local area.

When Cable is selected, the TV will detect cable company

supplied signals and will search for cable TV (NTSC,QAM

modulated) channels available in your area.

The function search for NTSC program first

and then search for ATSC or QAM program.

Add Channel Scan

20 TV LCD-TFT

Move /OK: Select /EXIT/ MENU: Exit

Page is loading ...

Haier HLC32 User manual

This manual is also suitable for

Haier HLC32 User manual

Related papers

Other documents