CREE LIGHTING OSQ-C Area Light Installation guide

Brand: CREE LIGHTING

Model: OSQ-C Area Light

Category: Motorcycle Accessories

Type: Installation guide

OSQ-C Series

LED Area Light

1 of 2 LPN00877X0010A0_A

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should

always be followed including the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

1. DANGER- Risk of shock- Disconnect power before installation.

DANGER – Risque de choc – Couper l’alimentation avant

l’installation.

2. This luminaire must be installed in accordance with the NEC or

your local electrical code. If you are not familiar with these codes

and requirements, consult a qualied electrician.

Ce produit doit être installé conformément à NEC ou votre code

électrique local. Si vous n’êtes pas familier avec ces codes et ces

exigences, veuillez contacter un électricien qualié.

SAVE THESE INSTRUCTIONS FOR

FUTURE REFERENCE

• Prior to installation, store luminaire in a dry location

protected from rain, dust, and outdoor environment. If

equipped with a photocell receptacle, remove the protective

cover only if immediately replacing with a suitable photocell,

shorting cap, or other compatible device. The protective

socket cover is not intended to remain in place after

installation. Do NOT leave receptacle open to environmental

elements. Luminaires with a top-mounted photocell

receptacle should not be installed in an up-light position or at

a tilt greater than 45 degrees from the down-light position.

****Full Detailed Mechanical Installation Instructions are Shipped in the

Mounting Kit Package.

FIELD ADJUSTABLE DIMMING  (OPTIONAL)

NOTE: This luminaire may be provided with field adjustable

dimming. If so, luminaires leave the factory adjusted to the

maximum setting specified when ordered. Visit www.creelighting.

com/products for product specification sheets.

STEP 1:

The Dimming module is located inside the luminaire. Open the

luminaire door cover by loosening the (7) screws. See Figure 1.

STEP 2:

Establish the desired input power multiplier by referring to the

product dimming spec sheet and turn the switch to the correlating

position

STEP 3:

Adjust the Dimming Module, see Figure 2, to the selected position

and reinstall the cover ensuring no wires are pinched. Torque

screws to

23 in-lbs (2.6 N-m).

Luminaire Cover Door

2 of 2 LPN00877X0010A0_A

www.creelighting.com

subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree® and the Cree Lighting logo are

registered trademarks of Cree, Inc. NEMA® is a registered trademark of the National Electrical Manufacturers Association.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks is

under license. Other trademarks, service marks, and trade names are those of their respective owners. IOS is a registered

trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. Android

is a trademark of Google, Inc.

ELECTRICAL CONNECTIONS

STEP 1:

NOTE: Luminaires with BML sensor will have the dimming leads

capped off. Keep the dimming leads on these luminaires capped

off.

Using Listed 90°C minimum rated wire connectors make the

following electrical connections within the adjustable fitter

wiring compartment:

a. For 120/277/347V connect the black fixture lead to the

voltage supply or Hot 1 (for 208/240/480V wiring).

b. For 120/277/347V connect the white fixture lead to the

neutral supply or Hot 2 (for 208/240/480V wiring).

c. Connect the green or green/yellow ground lead to

ground.

d. If fixture ordered with –F fuse option (Single-Phase

connection only)

• Connect the black fixture lead to the voltage supply.

• Connect the white fixture lead to the neutral supply.

• Connect the green or green/yellow ground lead to

ground.

e. If Dimming is an option; connect the violet dimming

positive fixture lead to the supply dimming positive lead.

If dimming is not being used, cap off the violet lead.

f. If Dimming is an option; connect the grey or pink

dimming negative fixture lead to the supply dimming

negative lead. If dimming is not being used, cap off the

grey or pink lead.

g. Connect orange fixture lead to orange supply lead.

h. Connect red fixture lead to brown supply lead.

LINE

OR HOT 1

GREEN

LINE-BLACK

GROUND-GREEN

NEUTRAL-WHITE

DIM (-) GREY

OR PINK

DIM (+) VIOLET

NEUTRAL

OR HOT 2

DIM (+)

DIM (-)

SUPPLY WIRING

(DIMMING OPTIONAL)

LUMINAIRE

RED

ORANGE

BROWN

(CONTROLS FROM

PHOTOCONTROL

OPTIONAL)

ORANGE

NEMA® RECEPTACLE (OPTIONAL)

PLEASE READ: The method for rotating this NEMA receptacle is

different than other Cree Lighting Products. Rotation of the photocontrol

receptacle after photocontrol installation is not recommended. This may

disengage the electrical contacts, compromise the seal, or damage the

photocontrol.

STEP 1:

Remove protective cap.

STEP 2:

If necessary, rotate photocontrol receptacle so the arrow is pointed in the

north direction. Some photocontrols operate best when aimed between

the north-west and north-east direction. To rotate, lift upwards on the

photocontrol receptacle to disengage the internal lock, rotate, and then

release the photocontrol receptacle to return it to the locked position.

Ensure that the photocontrol receptacle has returned to the fully locked

position.

STEP 3:

Install photocontrol into photocontrol receptacle by inserting the blades

into the receptacle and turning clockwise. Ensure that the photocontrol is

fully locked in place by gently pulling upwards. Less than full engagement

of the photocontrol may result in a compromised seal.

BLUETOOTH® TECHNOLOGY ENABLED MULTILEVEL SENSOR

(OPTIONAL)

The 20’ to 40’ sensor lens comes installed on the sensor on the OSQ

luminaires. An 8’ to 20’ sensor lens and aisle shroud may be found in the

hardware bag. To change the lens, unscrew the existing lens, remove the

shroud from the replacement lens and screw it back on to the sensor.

For Sensor information please visit the Leviton website, www.Leviton.com

and search on ZLDxZ-xxx/OFDxZ-xxx.

Configuration is made using the Leviton Smart Sensor App from a

smartphone or other Bluetooth® enabled Android or iOS device. The

Smart Sensor App can be downloaded from either Goggle Play or Apple

Store.

CREE LIGHTING OSQ-C Area Light Installation guide

Brand: CREE LIGHTING

Model: OSQ-C Area Light

Category: Motorcycle Accessories

Type: Installation guide

Download PDF

report