SCE -AC5100B120VSS Air Conditioner User manual

Brand: SCE

Model: -AC5100B120VSS Air Conditioner

Type: User manual

SCE-AC5100B120VSS Air Conditioner is a product designed for use in industrial environments to protect temperature sensitive components in control cabinets and enclosures.

The air conditioner uses the principle of a compression refrigerator and has a cooling capacity of 5100 BTU (1494 Watts) at 95°F / 95°F and a heating capacity of 1000 W. The unit is powered by a 120 V - 50/60 Hz power supply and has a rated current of 9.6 A at 95°F / 95°F. The maximum current draw is 14.2 A and the power consumption is 880 W at 95°F / 95°F, with a maximum power consumption of 1.29 kW.

SCE-AC5100B120VSS Air Conditioner is a product designed for use in industrial environments to protect temperature sensitive components in control cabinets and enclosures.

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

1. User Manual ............................................................................................ p. 2

2. Legal Regulations ................................................................................... p. 2

3. Safety Instructions ................................................................................. p. 3

4. Functional Principle ............................................................................... p. 4

5. Technical Data ......................................................................................... p. 5

6. Performance Graph ................................................................................ p. 6

7. Mounting .................................................................................................. p. 7

8. Mounting Principle ................................................................................. p. 7

9. Cutout Dimensions ................................................................................. p. 8

10. Dimensions (H x W x D) ......................................................................... p. 8

11. Electrical Connection ............................................................................. p. 9

12. Controller Programming ........................................................................ p. 9

13. Wiring Diagram ....................................................................................... p. 13

14. Taking Into Operation ............................................................................. p. 15

15. Repair ....................................................................................................... p. 15

16. Maintenance & Cleaning ........................................................................ p. 16

17. Transport & Storage ............................................................................... p. 16

18. Parts Supplied ......................................................................................... p. 16

19. Warranty / Limits of Liability ................................................................. p. 17

User Manual SCE-AC5100B120V, SCE-AC5100B120VSS & SCE-AC5100B120VSS6

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

1. User Manual

This instruction manual contains information and instructions to enable the user to work safely, correctly and economically

on the unit. Understanding and adhering to the manual can help one:

• Avoid any dangers

• Reduce repair costs and stoppages

• Extend and improve the reliability and working life of the unit

PLEASE ENSURE TO USE THE RIGHT VERSION OF THE INSTRUCTION MANUAL SUITABLE FOR YOUR UNIT

Conditions of Use

The unit is to be used exclusively for the dissipation of heat from control cabinets and enclosures in order to protect

temperature sensitive components in an industrial environment. To meet the conditions of use, all the information and

instructions in the instruction manual must be adhered to.

General Danger

Indicates compulsory safety regulations which are not covered by a specic pictogram such

as one of the following.

High Electric Voltage

Indicates electric shock danger.

Important Safety Instruction

Indicates instructions for safe maintenance and operation of the unit.

Attention

Indicates possible burns from hot components.

Attention

Indicates possible damage to the unit.

Instruction

Indicates possible danger to the environment.

2. Legal Regulations

Liability

The information, data and instructions contained in this instruction manual are current at the time of going to press. We

reserve the right to make technical changes to the unit in the course of its development. Therefore, no claims can be

accepted for previously delivered units based on the information, diagrams or descriptions contained in this manual. No

liability can be accepted for damage and production caused by:

• Disregarding the instruction manual

• Operation error

• Inappropriate work on or with the unit

• The use of non-specied spare parts andaccessories

• Unauthorized modications or changes to the unit by the user or his personnel

Saginaw Control & Engineering is only liable for errors and omissions as outlined in the guarantee conditions contained in

the main contractual agreement. Claims for damages on any grounds are excluded.

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

3. Safety Instructions

Upon delivery the unit is already meeting current technical standards therefore it can be safely taken into operation. Only

trained specialists are allowed to work on the unit. Unauthorized personnel must be prohibited from working on the unit.

Operating personnel must inform their superiors immediately if any malfunction of the unit becomes apparent.

Please note that before starting to work on or with the unit, a procedure must be carried out inside the cabinet on which the

unit is to be mounted.

Before commencing work inside the cabinet, the control cabinet manufacturer’s instruction must be read with regards to:

• Safety instructions

• Instructions on taking the cabinet out of operation

• Instructions on the prevention of unauthorized cabinet reconnection

The electric equipment meets the valid safety regulations. One can nd dangerous voltage (above 50V AC or above 100V

DC):

• Behind the control cabinet doors

• On the power supply in the unit housing

The units have to be fused according to the type plate and the wiring diagram. Switch the unit o immediately if the electric

power supply is interrupted.

Danger Through Incorrect Work on the Unit

Only specialized personnel are allowed to maintain and clean the unit. Regular maintenance

and cleaning must be kept in order to ensure that the unit remains in perfect working condition

and has a long working life.

Danger from Electric Voltage

Only specialized personnel are allowed to maintain and clean the unit. The personnel must

ensure that for the duration of the maintenance and cleaning, the unit is disconnected from

the electrical supply.

Attention

Damage to the unit through the use of inappropriate cleaning materials. Please do not use

aggressive cleaning material.

Instruction

Damage to the environment through unauthorized disposal. All spare parts and associated

material must be disposed of according to the environmental laws.

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

4. Functional Principle

The unit functions on the principle of the compression refrigerator. The main components are: refrigerant compressor,

condenser, choke and evaporator. These four components of the refrigerant plant are connected with each other by pipes

to form a hermetically sealed system in which the refrigerant (R134a) circulates.

1. Air Intake, Cabinet Side

2. Radial Fan, Cabinet Side

3. Evaporator

4. Air Outlet, Cabinet Side

5. Compressor

6. Air Intake, Ambient Side

7. Radial Fan, Ambient Side

8. Condenser

9. Air Outlet, Ambient Side

10. Filter Dryer

11. Expansion Valve

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

5. Technical Data

Part Numbers SCE-AC5100B120V

SCE-AC5100B120VSS

SCE-AC5100B120VSS6

Cooling Capacity @ 95°F / 95°F 5100 BTU (1494 Watts)

Cooling Capacity @ 131°F / 131°F 5120 BTU (1500 Watts)

Heating Capacity 1000 W

Compressor Reciprocating Compressor

Refrigerant R134a

Refrigerant Charge 14.0 oz

Max. Pressure 348 psig

Operating Temperature Range -4°F - 131°F

Max. Air Volume Flow Ambient Air Circuit: 385 cfm

Cabinet Air Circuit: 235 cfm

Mounting External

Housing Material Mild Steel, Powder Coated

SS: Stainless Steel AISI 304

SS6: Stainless Steel AISI 316

Dimensions (H x W x D) 45.28 x 15.55 x 10.63 inch

Weight 113 lbs

Cutout Dimensions 12.40 x 10.40 inch

12.40 x 8.30 inch

Rated Operating Voltage / Frequency 120 V - 50/60 Hz

Rated Current @ 95°F / 95°F 9.6 A

Starting Current 32 A

Max. Current 14.2 A

Power Consumption @ 95°F / 95°F 880 W

Max. Power Consumption 1.29 kW

Fuse Rating 25A (T) - Time Delayed [Slow Acting]

SCCR 5kA

Transformer Inrush 120A 0.01 Sec. on 120V & 460V Unit Class CC fuse / Class C Breaker Not Recommended

Circuit Breaker – MCB Type D or K Slow Acting 16A Slow Acting

Connection Connection Terminal Block

NEMA Protection Class NEMA 3, 3R, 4 & 12

SS: NEMA 3, 3R, 4, 4X & 12

Approvals CE / cURus / UL Listed

Industry Standards IS19

SS: IS20

Sound Level at 1.5 meters 70 db(A)

Max Voltage at Door Switch 5 A DC

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

6. Performance Graph

Enviro-Therm® Air Conditioners 5100 BTU/HR (1494Watts)

Performance Curve

Ambient Temperature (°C)

Cooling Capacity

(BTU)

SCE-AC5100B230V, SCE-AC5100B120V, SCE-AC5100B460V

SCE-AC5100B230VSS, SCE-AC5100B120VSS, SCE-AC5100B460VSS

SCE-AC5100B230VSS6, SCE-AC5100B120VSS6, SCE-AC5100B460VSS6

Enclosure Air Temp

131°F/55°C 122°F/50°C 95°F/35°C 68°F/20°C

Cooling Capacity

(Watt)

Ambient Temperature (°F)

65 75 85 95 105 115 125 135

18 24 29 35 41 46 52 57

8000

7000

6000

5000

4000

3000

2000

2344

2051

1758

1465

1172

879

586

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

7. Mounting

Always disconnect the power supply before opening the unit.

Heat load to be dissipated from enclosure should not exceed specic cooling output of the unit at any condition. When

selecting a cooling unit, always allow for a safety margin of at least 15% extra cooling output in the worst conditions. Air

inlets and outlets must be completely free from obstruction.

Ensure that ows of air leaving and entering the cooling unit, internal and external, are not obstructed. Cooling unit enclosure

air suction hole must be installed at the highest possible point. When installing the unit on a door ensure it can take the

weight.

Before drilling the enclosure, ensure the xing elements and couplings will not interfere with the equipment inside the

enclosure itself. Disconnect power before starting any work inside the enclosure. Following this 1:1 Scale Drilling Template,

drill the holes and make the required cuts on the enclosure. This template may have been aected by storage conditions,

please check this template by verifying values of the largest dimensions before drilling. Fit the sealing strip to the cooling

unit on the side connected to the enclosure and follow the installation diagram.

8. Mounting Principle

1. M6 Bolts

2. M6 Toothed Washers

3. M6 Flat Washers

4. Enclosure

5. Mounting Gasket

6. Cooling Unit

• Do not use within the rst 15 minutes after installation!

• Use only the supplied mounting hardware.

• Tighten fasteners to 40 inch lb.

• Ensure the mounting surface does not warp after assembly

and reinforce it if necessary.

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

9. Cutout Dimensions

15.55

45.28

10.70

4° SLOPE

.312

(x10)

.98

10.83

.98

15.55

13.98

12.40

1.57

10.43

.59

3.94

8.27

21.06

45.28

MOUNTING PATTERN

INTERNAL AIR

OUTLET

INTERNAL AIR

INLET &

ELECTRICAL

CONNECTIONS

10. Dimensions (H x W x D)

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

11. Electrical Connection

The cooling unit is used where heat needs to be dissipated from electrical control cabinets or similar enclosures in order to

protect heat sensitive components. The unit has two completely separate air circuits which ensure that the clean cabinet

air does not come into contact with the ambient air which may well be dirty or polluted. Control cabinet air conditioners can

dissipate large quantities of heat from sealed enclosures, such as control cabinets, into the ambient air and at the same time

reduce the cabinet internal temperature to below that of the ambient air.

The control cabinet air conditioner can function without problems in extreme ambient conditions (e.g. dusty and oily air)

with a standard operating temperature ranging between -4°F and 131°F. The stated cooling capacities are according to DIN

3168.

Door Switch

The unit can be switched on and o via a door contact switch. When delivered the door contact terminals are bridged on the

female connector. To connect the door contact switch remove the bridge and connect door contact switch. The contact must

be closed when the cabinet door is closed.

12. Controller Programming

SET

TEST

BMS PRG

The cooling unit is intended to be used as a complementary accessory to larger industrial

equipment. The unit is used where heat needs to be dissipated from electrical control

cabinets or similar enclosures in order to protect heat sensitive components. It is not

intended for household use. The unit has two completely separate air circuits which

ensure that the clean cabinet air does not come into contact with the ambient air which

may well be dirty or polluted. Enclosure cooling units can dissipate large quantities of

heat from sealed enclosures such as electrical enclosures into the ambient air and at

the same time reduce the cabinet internal temperature to below that of the ambient air.

The unit can function without problems in extreme ambient conditions (e.g. dusty

and oily air) with a standard operating temperature ranging between +10°C and

+55°C. Units can be ordered with an additional electrical cabinet heater. For the

cooling capacities and environmental ratings please refer to the type plate data.

The display shows the temperature in the range of -50°C to +150°C (-58°F to +302°F). The

temperature is displayed with resolution of tenths between -19.9°C and +99.9°C (-3.8°F

to +211.8°F). During programming, it shows the codes and values of the parameters. The

display also shows icons according to occurring events.

Controller

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

The operating parameters can be modied using the front keypad. Access diers

depending on the type of parameter. Access to conguration parameters is protected

by a password that prevents unwanted modications or access by unauthorised persons.

Display icons

Programming

Icon Function Description

Compressor relay active

Alarm relay active

Heater relay active

Ambient blower relay active

Alarm

Heating mode

Cooling mode in progress

Flashes when activation is delayed or inhibited

by protection times, external disabling, or other

procedures in progress

Flashes when alarms are active

Signals operation of unit in heating mode

Activated only by manual procedure

PRG

SET

Setting cooling set point, St1:

Setting heating set point, St2 (only for units supplied with internal heater):

1. Press “SET” twice slowly and display should show St2 and then the pre-set value of St2.

(default: +5°C / +41°F)

2. Reach the desired value by using ▲ or ▼.

3. Press “SET” again to save the new value of St2.

PRG

SET

1. Press and hold “SET” until the display shows St1. Once released the pre-set value of St1 will appear.

(default: +35°C / +95°F)

2. Reach the desired value by using ▲ or ▼.

3. Press “SET” again to save the new value of St1.

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

Setting temperature units (°C / °F), low temperature alarm and high temperature alarm:

PRG

SET

1. Press “PRG” button for 5 seconds to reach the modiable parameter list.

2. Use ▲ or ▼ to reach the desired parameter:

• C18 for temperature unit of measure

• °C = 0

• °F = 1

• P25 for low temperature alarm threshold (default -10°C / +14°F)

• P26 for high temperature alarm threshold (default +55°C / +131°F)

3. Press “SET” on the desired parameter to display the current value.

4. Use ▲ or ▼ to reach the desired value.

5. Pressing “SET” temporarily saves the new value and returns to the parameters list.

6. Repeat steps 2-5 to set other parameters.

7. Press “PRG” for 5 seconds to permanently save the new values.

Test Function

Dierent test functions can be used depending on the combination of keys pressed. Such tests run for

the duration of 4 minutes.

• “SET+▲” tests Compressor and Ambient Blower relays.

• “SET+▼” tests Alarms and Heater relays

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

Alarm Relay Function

Both normally closed (NC) and normally open (NO) alarm contacts are provided. These refer to the alarm

state. Under normal conditions, the NC contact is closed and the NO contact is open. When an alarm

condition is present or the door contact is open, the NC contact will open and the NO contact will close.

System power failure will give an alarm condition.

Notes:

State 2: Additional icons (1,3,4, Reverse, Direct, Test) depending on operation.

State 3: The display shows “OFF” alternating with the standard display.

State 4: The display shows “EXX” alternating with the standard display – at the same time, the alarm

icon ashes.

Typical alarm codes:

Error Code Description

E01 Probe B1 fault

E02 Probe B2 fault

E04 High temperature alarm

E05 Low temperature alarm

• Whilst programming, if no button is pressed for 10 seconds, the display starts ashing, and after 1

minute returns to the main display without saving changes.

• l To increase scrolling speed, press and hold the ▲ or ▼ button for at least 5 seconds.

• When pressing “PRG” for 3 seconds, the rmware revision code is displayed for 2 seconds.

• When cleaning the controller panel, do not use ethanol, hydrocarbons, ammonia or their byproducts.

Use neutral detergents and water.

• In order to protect the unit’s components, minimum relay output on (3 or 7 minutes) and o (4

minutes) times and minimum time (7 or 11 minutes) between activation of the same relay output are

applied.

• In case of digital inputs not congured, probes not tted or congured, or St2 not enabled on the

controller the display shows ‘nO’.

State Alarm Relay Display

1 System powered OFF

2 System powered ON

-NO ALARM

-Door Contact Closed

3 System powered ON

-Door Contact Open

4 System powered ON

-ALARM STATE

13 14 15

SET

TEST

BMS PRG

SET

TEST

BMS PRG

SET

TEST

BMS PRG

SET

TEST

BMS PRG

Important Notes

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

13. Wiring Diagram

Mc Compressor

Ma Ambient Fan

Mi Internal Fan

Cc Compressor Capacitor

Ca Ambient Fan Capacitor

Ci Internal Fan Capacitor

IH Internal Heater

TS Temperature Sensor

CE Condensate Evaporator

CH Compressor Heater

C Controller

AR Alarm Relay

X3 Transformer Connector

X4 Electrical Supply Connections

1 L1 - 120V

2 —

3 L2/N - 120V

4 Earth/Ground

5 P1 High Temp alarm NO

6 P2 High Temp alarm COM

7 P3 High Temp alarm NC

8 T1 Door Switch Contact

9 T2 Door Switch Contact

Notes:

#1 Mi1 not used in SCE-AC5100B120V/SS

#2 X6 is plugged into X5 for units with heater

#3 Ma1 + Ca1 not used in SCE-AC5100B120V/SS

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

14. Taking Into Operation

Attention!

The unit can be damaged by lack of lubricant. To ensure that the compressor is adequately lubricated, the oil, which has

been displaced during transport, must be allowed to ow back into it. The unit must therefore be allowed to stand for at

least 30 minutes before being connected to the mains and taken into operation. Upon connection the internal fan will start

working. If the temperature inside the enclosure is higher than the set value of the controller, both the compressor and

external air fan start working. Once the air inside the enclosure reaches the set temperature, the compressor and external

fan will stop.

The unit is pre-set at 95°F, which is suitable for most of the electronic devices.

If Drainage required, use PVC 10mm (3/8 inch) ID Hose.

15. Repair

Failure Condition Cause Solution

Unit Does

Not Cool

Internal fan does not work Power not connected. Verify power supply

Internal fan works, external fan

and compressor do not work

Enclosure temperature is

below setting temperature (St) Verify values of parameter "St"

Door switch contact is open Verify door switch

Controller does not work Replace controller

Internal fan works, external

fan and compressor do not

work Display shows alternating

"OFF" and temperature

The sequence of the phases

inside the power supply

connector is incorrect

Change phases inside power

supply connector

External and internal fan work,

compressor does not work

Compressor motor electrical

failure

Verify external fan, verify

ambient temperature, clean

condenser

Capacitor for compressor failed Replace capacitor

Compressor works, external

fan does not work

External fan needs to be

replaced Replace external fan

Enclosure

Overheating

Compressor and fans (external

and internal) work all the time Unit cooling undersized Enclosure needs a bigger

cooling unit

Enclosure needs a bigger

cooling unit

Thermal compressor protector

triggered

Verify ambient temperature,

clean condenser

Refrigerant leakage Contact dealer/service center

Excessive

Condensate

Door enclosure open Ambient air gets into the

enclosure

Ensure door is closed, add a

door switch and connect it to

controller

Door enclosure closed

Enclosure IP degree minimum

IP54 Seal openings on enclosure

Damaged/misplaced sealing

strip Repair strip accordingly

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

17. Transportation & Storage

During transport and storage the cooling unit must be kept in the position marked on the box and at a temperature between

-40˚F and 158˚F and a relative humidity of max. 95% (at 77°F). Check that the packaging has not been damaged during

transport.

18. Parts Supplied

1 x Air Conditioner

1 x Instruction Manual with technical information

1 x Mounting Template in 1:1 scale

1 x Installation pack containing:

10 x M6 Bolts

10 x A6.4 Toothed Washers

10 x A6.4 Washers

1 x Female Connector with shorted wired positions for door contact

Saginaw Control and Engineering

95 Midland Road

Saginaw, MI 48638-5770

Phone: (989) 799-6871

Fax: (989) 799-4524

[email protected]

16. Maintenance & Cleaning

Always switch power supply o before starting any maintenance on the unit.

Any repairs that may be needed must only be done by qualied personnel. The cooling unit is a low maintenance type and

for most environments, no lter is required. If an air lter is installed, check it periodically for dirt and clogs. Clean or replace

lter when necessary.

Disposal

The cooling unit contains R134a refrigerant and small quantities of lubricating oil. Replacement, repairs and nal disposal

must be done according to the regulations of each country for these substances.

SAGINAW CONTROL & ENGINEERING • A/C USER MANUAL

19. Warranty / Limits of Liability

All goods manufactured by SCE shall be warranted to be free of defects in material or workmanship for a period of two years

from the date of shipment. Should the product be proven to SCE to be defective, we shall option to repair or replace the

product. At no time will SCE reimburse purchaser for unauthorized rework on any product.

Air Conditioners & Heat Exchangers are warranted on parts and service for a period of two years from the date of shipment

by Saginaw Control and subject to the following conditions and exclusions:

All Goods must be installed and operated according to the following specications: Maximum voltage variation no

greater than plus or minus 10% of nominal rating; Maximum frequency variation no greater than plus or minus 3

Hz. from nominal rating; Must not exceed minimum and maximum rated temperatures; Must not exceed (BTU/Hr)

rating; Filters must be cleaned regularly; Must be installed and grounded in accordance with all relevant electrical

and safety codes, as well as the National Electric Code and OSHA rules and regulations; Must be installed in a

stationery application, free of vibration.

Our warranty does not warranty product that has been modied, subjected to abuse, negligence in operation or

maintenance, or if product is used in a manner that exceeds its designed capabilities and rating.

Warranty related claims will be returned to the factory for evaluation and nal disposition of the claim, any replacement parts

will be invoiced at standard pricing and credit issued for the returned product. If the product has been found to have been

modied, subjected to abuse, negligence in operation or maintenance, or if product has been used in a manner that exceeds

its designed capabilities and rating, credit may be reduced, denied or additional cost may be assessed and passed on to the

purchaser, such as return freight.

SCE -AC5100B120VSS Air Conditioner User manual

Brand: SCE

Model: -AC5100B120VSS Air Conditioner

Type: User manual

SCE-AC5100B120VSS Air Conditioner is a product designed for use in industrial environments to protect temperature sensitive components in control cabinets and enclosures.

Download PDF

report