2. Interlogix
  3. D1300 Series IFS RS-485 Point to Point Data Transceiver

Interlogix D1300 Series IFS RS-485 Point to Point Data Transceiver Owner's manual

  • Hello! I've reviewed the datasheet for the GE D1300 series data transceivers. This document specifies devices for point-to-point signal transmission over fiber. I am familiar with its features, including RS-485 compliance, data re-clocking, and hot-swappable modules. Feel free to ask me any questions about the D1300, D1300WDMA, D1300WDMB, D1320 and D1325 models.
  • What type of data signals do these transceivers transmit?
    What is the maximum data rate supported by these transceivers?
    Are these transceivers compatible with other IFS series devices?
GE
Security
D1300 Series
IFS RS-485 (2-wire)
Point-to-Point Data Transceivers
• Meets EIA RS-485 Specifications
• Tested and Certified by an Independent Testing
Laboratory for Full Compliance with the Environmental
Requirements (Ambient Operating Temperature,
Mechanical Shock, Vibration, Humidity with Condensation,
High-Line/Low-Line Voltage Conditions and Transient
Voltage Protection) of NEMA TS-1/TS-2 and the Caltrans
Specification for Traffic Signal Control Equipment.
• Automatic Resettable Solid-State Current Limiters
• Power, Transmit and Receive Data Status LED Indicators
• No In-field Electrical or Optical Adjustments Required
• Data rates up to 400 kbps NRZ
• Data Re-clocking
• Transparent to Data Encoding / Compatible with
Major Data Protocols
• Point-to-Point Network Architecture
• 2-Wire (Half-Duplex)
• True Tri-State Output
• Hot-Swappable Rack Modules
• Distances up to 20 Miles (33 km)
• Comprehensive Lifetime Warranty
Standard Features
• Access Control Systems
• Building Automation and Environmental Control Systems
• Computer/Data Equipment
• Fire & Alarm Systems
• ITS Traffic Signalization Networks
Application Examples
Overview
The IFS D1300 series data transceivers provide point-to-
point transmission of half-duplex (2-wire) EIA RS-485
tri-state data signals over one or two optical fibers. The
transceivers are transparent to data encoding allowing for
broad-range compatibility. When used as a line-terminating
device, these modules are also compatible with the IFS
D2300 series drop and repeat data transceivers. Models
within this series are available for use with multimode or
single mode optical fiber. Plug-and-play design ensures
ease of installation requiring no electrical or optical
adjustments. Each transceiver incorporates power and
transmit/receive data status indicating LED’s for monitoring
proper system operation. The modules are available in
either stand-alone or rack mount versions.
RS-485 (2-wire)
Point-to-Point
Data Transceivers
For implementing point-to-point
transmission of half-duplex (2-wire)
EIA RS-485 tri-state data signals
over one or two optical fibers.
firealarmresources.com
D1300
Control
Data
Control
Data
Host
2 Fibers
62.5/125µm MM
D1300
up to 1.9 miles
(3 km)
ifs International
Fiber
Systems
Incorporated
203.426.1180
ifs International
Fiber
Systems
Incorporated
203.426.1180
Specifications
Data
Data Interface: RS-485 (2-wire)
Data Rate: DC - 150 Kbps*
Total Network Pulse Distortion: <1µs
*-HS Option Data Rate: DC - 400 Kbps
Wavelength D1300 and D1300WDMB: 850 nm, Multimode
All others: 1310 nm, Multimode or Single Mode
Number Of Fibers 2
Connectors
Data and Power: Terminal Block with Screw Clamps
Optical: ST
Electrical & Mechanical
Power:
Surface Mount: 12 VDC @ 200 mA to 24 VDC @ 100 mA
Rack: From Rack
Number of Rack Slots: 1
Current Protection: Automatic Resettable Solid-State Current Limiters
Circuit Board: Meets IPC Standard
Size (in./cm.) (LxWxH)
Surface Mount: 7.0 x 4.9 x 1.0 in., 17.8 x 12.5 x 2.5 cm
Rack Mount: 7.0 x 4.9 x 1.0 in., 17.8 x 12.5 x 2.5 cm
Shipping Weight: < 2 lbs./0.9 kg
Environmental
MTBF: > 100,000 hours
Operating Temp: -40° C to +74° C
Storage Temp: -40° C to +85° C
Relative Humidity: 0% to 95% (non-condensing)†
†May be extended to condensation conditions by adding suffix ‘–C’ to
model number for conformal coating.
System Design
Part Number Opt. Pwr. Budget Max. Distance*
Multimode
62.5/125µm**
Single Mode
9/125µm
1.9 miles (3 km)
1.9 miles (3 km)
1.9 miles (3 km)
6 miles (10 km)
20 miles (33 km)
PS-12VDC 12 Volt DC Plug-in Power Supply (Included)
PS-12VDC-230 12 Volt DC Plug-in Power Supply, 230 VAC Input (Included if specified at time of order)
Add ‘-24’ for 24 VDC Power (Extra charge, consult factory)
Add ‘-R3’ to Model Number for R3 Rack Mount - No Charge (Requires R3 Rack purchased separately)
Add ‘-C’ for Conformally Coated Printed Circuit Boards (Extra charge, consult factory)
Add ‘-HS’ for High Speed Data Rates up to 400 Kbps (Extra charge, consult factory)
D1300
D1300WDMA
D1300WDMB
D1320
D1325
2
1
1
2
1
11 dB
11 dB
11 dB
10 dB
11 dB
Fibers Required
RS-485 Data Transceiver (850 nm)
RS-485 Data Transceiver (850 nm)
RS-485 Data Transceiver (1310 nm)
RS-485 Data Transceiver (1310 nm)
Data Transceiver (1310 nm)
Description
Ordering Information
Made in the USA
Complies with FDA Performance
Standard for Laser Products, Title 21,
Code of Federal Regulations, Subchapter J
*Optical transmission distance is limited to optical loss of the fiber and any additional loss introduced by connectors, splices and patch panels.
Distance can also be limited by fiber bandwidth. **For 50/125 Fiber, subtract 4 dB from Optical Power Budget. ♦All accessories are third party manufactured.
Accessories♦
Options
GE
Security
North America
T 888-GE-SECURITY
888-437-3287
F 503-691-7566
E [email protected]
Asia
T 852-2907-8108
F 852-2142-5063
Australia and New Zealand
T 613-9239-1200
F 613-9239-1299
Europe
T 44-113-238-1668
F 44-113-253-8121
Latin America
T 305-593-4301
F 305-593-4300
gesecurity.com/ifs
Specifications subject to
change without notice
© 2008 General Electric Company
All Rights Reserved
Agency compliance
firealarmresources.com
/