Gamber-Johnson 7160-0182 Installation guide

Gamber-Johnson
Brand
Gamber-Johnson
Model
7160-0182
Type
Installation guide

This manual is also suitable for

Gamber-Johnson 7160-0182 is a vehicle base compatible with various Dodge RAM and Sterling Bullet models. This product enhances in-vehicle stability and supports mounting additional equipment. It is designed to be installed in front of the passenger seat, utilizing existing seat bolt holes. The base provides a secure platform for attaching support braces for increased stability. By utilizing accessories like the DS-STEP and DSLOWER poles, users can customize the setup based on their vehicle's configuration, whether it has a center console or not.

Gamber-Johnson 7160-0182 is a vehicle base compatible with various Dodge RAM and Sterling Bullet models. This product enhances in-vehicle stability and supports mounting additional equipment. It is designed to be installed in front of the passenger seat, utilizing existing seat bolt holes. The base provides a secure platform for attaching support braces for increased stability. By utilizing accessories like the DS-STEP and DSLOWER poles, users can customize the setup based on their vehicle's configuration, whether it has a center console or not.

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© Copyright 2017 Gamber-Johnson, LLC
7160-0182 VEHICLE BASE
Revision Form
STERLING BULLET 4500/5500 (2007-2009)
PS-001
Printing Spec:
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
DODGE RAM 2500-5500 (2002+)
DODGE RAM 1500 (2002-2018)
DODGE RAM 1500 CLASSIC BODY STYLE (2019+)
Product
INSTALLATION INSTRUCTIONS
Rev F INST-425
Begin by moving the passenger seat as far back as possible.1.
Remove the front seat bolts of the front passenger seat that secure the seat to the vehicle 2.
floor.
WIthout removing the seat, place the vehicle base in front of the bolt holes of the seat legs.3.
Re-install the seat bolts.4.
Slide the base towards the center of the vehicle as far as possible.5.
Tighten the seat bolts.6.
If the vehicle does not have a center console it is recommended to use a DS-STEP and a DS-
LOWER-7 pole. If the vehicle does have a center console it is recommended to use a DS-
LOWER-13 pole.
Attach support brace 7160-0230 for increased stability.
To Install:
IMPORTANT SAFETY INFORMATION
You must read and follow all installation instructions. Failure to follow installation instructions may result in death or serious •
bodily injury.
Keep these installation instructions with the product and readily available in the vehicle for future reference of other users of the •
product.
Additional copies of the installation instructions can be obtained from Gamber Johnson or by scanning the QR code located on •
the product if abailable.
DO NOT postion the equipment in front of an airbag. Equipment positioned in front of an airbag can cause serious injury or •
death when airbag is deployed.
Disconnect vehicle battery before installation. •
  • Page 1 1

Gamber-Johnson 7160-0182 Installation guide

Gamber-Johnson
Brand
Gamber-Johnson
Model
7160-0182
Type
Installation guide
This manual is also suitable for

Gamber-Johnson 7160-0182 is a vehicle base compatible with various Dodge RAM and Sterling Bullet models. This product enhances in-vehicle stability and supports mounting additional equipment. It is designed to be installed in front of the passenger seat, utilizing existing seat bolt holes. The base provides a secure platform for attaching support braces for increased stability. By utilizing accessories like the DS-STEP and DSLOWER poles, users can customize the setup based on their vehicle's configuration, whether it has a center console or not.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI