CERBERUS PYROTRONICS 10 Inch Bell1 Vibrating and Single Stroke Bells Owner's manual

2537

CATALOG NUMBER

Vibrating and Single Stroke Bells

lAC or DC Operation

lVibrating or Single Stroke

Units

lSturdy Metal Construction

lHigh dB Output

lStandard 4" Square

Mounting

lAvailable in 4", 6", 8" and

10" Sizes

lNoise Cancellation

Circuitry

lAvailable in Chime

l Listed

lULC Pending

IntroductionIntroduction

Cerberus Pyrotronics Vibrating and Single Stroke bells

provide high quality construction for maximum reliability

and customer satisfaction. Cerberus Pyrotronics bells

integral bell/chime design combines the bell mechanism

and gong/chime into one unit. Four gong sizes and a

chime are available to provide distinctive tones and to

overcome different ambient noise levels.

ENGINEER AND ARCHITECT SPECIFICATIONS

DescriptionDescription

Cerberus Pyrotronics bells are used in a variety of applica-

tions. Used in schools and other buildings, the Cerberus

Pyrotronics unique design provides a sound all its own.

Offered in chime, 4, 6, 8, and 10 inch gong or additional

strobe plate configurations, the signals can be used for

new installations or existing retrofits. Parallel units are

designed with terminals to insure proper supervision as

well as provide better electrical connections. Parallel

devices also include a blocking network for connection to

a supervised signal circuit. Each unit is provided with noise

cancellation circuitry to prevent the transmission of tran-

sient spikes, typically generated by DC contact type

electromechanical devices.

10” Bell10” Bell

firealarmresources.com

Cerberus Pyrotronics Bells

VIB = Vibrating

S.S. = Single Stroke

L.C. = Low Current

* For (Canada) ULC labeled models, add “-C” to the model number.

Bell / Chime Strobe Plates

Model No. Mounting Nominal

Voltage

Box Nominal Strobe Current Ratings (mA)

15 17 (15/75) 75 110

S( )6060H Horizontal Strobe 24 VDC 4 in. sq. 80 80 NA NA

S( )6090V Vertical Strobe 24 VDC 4 in. sq. 80 80 175 245

Model No. Mounting Nominal

Voltage

Box Nominal Strobe Current Ratings (mA)

15 17 (15/75) 75

S( )S-6060H Horizontal Strobe 24 VDC 4 in. sq. 144 144 328

S( )S-6090V Vertical Strobe 24 VDC 4 in. sq. 144 144 328

Stand alone strobes utilize wire nuts for connection. Terminal strips are available by modifying part number to read -FT (Flush with Terminals) or -ST (Surface with terminals). FS (single

gang) models are not available with terminals.

*Surface mount units are rated weatherproof when used with FWB-1 or FWB-2 surface weatherproof box.

Note ( ) represents strobe model, e.g., 15, 17, 75 or 110.

Stand alone strobes utilize wire nuts for connection. Terminal strips are available by modifying part number to read -FT (Flush with Terminals) or -ST (Surface with terminals). FS (single

gang) models are not available with terminals.

*Surface mount units are rated weatherproof when used with FWB-1 or FWB-2 surface weatherproof box.

Note ( ) represents strobe model, e.g., 15, 17 or 75.

Bell / Chime Sync Strobe Plates

Minimum db calculated from integrated sound power measurements at Underwriter's Laboratories per UL 464. Typical db measurements with conventional sound

level meters will be significantly higher in actual installation.

Model

Number

Part

Number Action Voltage Current

U.L. db @ 10’

4" Bell 6" Bell 8" Bell 10" Bell Chime

BT-F 500-694372 VIB 24 VDC 0.11A 87db

BE-F 500-694373 VIB 24 VDC 0.11A 87db

BS-F 500-694374 VIB 24 VDC 0.11A 84db

BF-F 500-694375 VIB 24 VDC 0.11A 87db

CH-F 500-694376 VIB 24 VDC 0.11A 81db