Trinamic TMCM-1260-CANopen Owner's manual

Brand: Trinamic

Model: TMCM-1260-CANopen

Type: Owner's manual

This manual is also suitable for

TMCM-1260-TMCL

Module for Stepper MODULE

TMCM-1260 Hardware Manual

Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18

The TMCM-1260 is a single axis motor controller/driver board for 2-phase bipolar stepper motors

with up-to 6A RMS motor current and 48V DC supply. It supports 6-point ramps in addition to linear

ramps.

Features

•Single axis controller/driver for 2-phase

bipolar stepper motor

•Linear and sixPoint™ramps

•+24V and +48V DC supply voltage

•Up to 6A RMS motor current

•RS485, CAN & USB interface

•integrated sensOstep encoder and

support for external encoder

•S/D interface

•multi-purpose inputs and outputs

Applications

•Laboratory Automation

•Manufacturing

•Semiconductor Handling

•Robotics

•Factory Automation

•Test & Measurement

•Life Science

•Biotechnology

•Liquid Handling

Simpliﬁed Block Diagram

Terms of delivery and rights to technical change reserved.

Download newest version at: www.trinamic.com

Read entire documentation.

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 2 / 30

Contents

1 Features 3

2 Order Codes 5

3 Mechanical and Electrical Interfacing 7

3.1 Size of board ................................................ 7

3.2 Board mounting considerations .................................... 7

4 Connectors 8

4.1 Power Supply Input Connector ..................................... 9

4.2 Motor Connector ............................................. 10

4.3 RS485 + CAN Connector ......................................... 10

4.4 USB Connector .............................................. 11

4.5 I/O Connector ............................................... 11

5 On-Board LEDs 12

6 Reset to Factory Defaults 13

7 I/Os 14

7.1 Analog input IN0 ............................................. 14

7.2 Digital inputs IN1 and IN2 ........................................ 14

7.3 HOME/STOP_L/STOP_R switch inputs ................................. 15

7.4 External incremental encoder input .................................. 15

7.5 Step/Direction inputs ........................................... 16

8 Communication 17

8.1 RS485 .................................................... 17

8.2 CAN ..................................................... 18

9 Motor driver current 20

10 Functional Description 22

11 Operational Ratings and Characteristics 23

12 Abbreviations used in this Manual 25

13 Figures Index 26

14 Tables Index 27

15 Supplemental Directives 28

15.1 Producer Information .......................................... 28

15.2 Copyright .................................................. 28

15.3 Trademark Designations and Symbols ................................. 28

15.4 Target User ................................................ 28

15.5 Disclaimer: Life Support Systems .................................... 28

15.6 Disclaimer: Intended Use ........................................ 28

15.7 Collateral Documents & Tools ...................................... 29

16 Revision History 30

16.1 Hardware Revision ............................................ 30

16.2 Document Revision ............................................ 30

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 3 / 30

1 Features

The TMCM-1260 is a single axis motor controller/driver board for 2-phase bipolar stepper motors with up-

to 6A RMS (8.4A peak) motor coil current. It supports linear ramps and unique sixPoint™ramps. It oﬀers

on-board sensOstep encoder and in addition, support for connection of external (incremental A/B) en-

coder. For driver-only applications, the TMCM-1260 oﬀers optically isolated Step/Direction inputs. When

using the on-board motion controller the optically isolated inputs are used for connection of end-switches.

The standard version of the TMCM-1260 oﬀers one analog input (0..10V range), two digital inputs and

one open-drain output (100mA load max.) For communication in addition to USB (Micro-USB connector),

RS485 and CAN serial interfaces are available. USB is intended mainly for ﬁrmware updates and param-

eter settings - supporting USB-powered operation (just the digital part) for easy data tranfer between PC

and TMCM-1260 module. With CANopen ﬁrmware CANopen protocol is supported via the CAN interface.

Motion Controller

•Motion proﬁle calculation in real-time

•On the ﬂy alteration of motor parameters (e.g. position, velocity, acceleration)

•Linear and unique sixPoint™ramp in hardware

•Encoder interface and Reference / Stop switch inputs

Driver

•Motor current: up to 6A RMS / 8.4A peak, (programmable in software)

•Supply voltage: +24V and +48V DC (+12. . . +54V DC)

•256 microsteps per fullstep

•spreadCycle™highly dynamic current control chopper

•stealthChop™for quiet operation and smooth motion

•programmable Step/Dir interface for driver-only applications with microstep interpolation

Encoder

•integrated sensOstep absolut position magnetic encoder (resolution: 1024 increments per rotation)

for step-loss detection under all operating conditions and positioning supervision (accuracy: +/- 5

encoder steps)

•support for external A/B incremental encoder in addition / as an alternative for the integrated en-

coder

•programmable encoder scaling and support for motor stop on encoder deviation

Interfaces

•RS485 interface (up-to 1Mbit/s)

•CAN interface (up-to 1Mbit/s)

•USB 2.0 full speed (12Mbit/s) device interface (micro-USB connector)

•Step/Dir input (optically isolated)

•Left and Right STOP switch inputs (optically isolated, shared with Step/Dir inputs)

•2 general purpose digital inputs

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 4 / 30

•Encoder input for incremental A/B encoder signals (shared with general purpose digital inputs)

•1 analog input (0..10V nom. input range)

•HOME switch input (shared with analog input)

Mechanical data

•Board size: 60mm x 60mm, height 26mm max. without mating connectors

•2 mounting holes for M3 screws

Software

•TMCL™remote (direct mode) and standalone operation (memory for up to 1024 TMCL™commands),

fully supported by TMCL-IDE (PC based integrated development environment). Please see TMCM-

1260 TMCL ﬁrmware manual for more details

•CANopen ﬁrmware with CANopen standard protocol stack for the CAN interface. Please see TMCM-

1260 CANopen ﬁrmware manual for more details.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 5 / 30

2 Order Codes

The standard version of the TMCM-1260 is pre-programmed with either TRINAMIC TMCL™ﬁrmware or

CANopen ﬁrmware.

On request a version with 3 analog inputs (0..10V) is available instead of one analog and two digital in-

puts on the I/O connector of the TMCM-1260. As this is an assembly version with diﬀerent components

concerning these inputs, all mechanical data and all other electrical data will be the same.

Order Code Description Size (LxWxH)

TMCM-1260-TMCL 1-axis bipolar stepper motor controller/driver, up-

to 6A RMS motor current, 48V nom. supply, in-

tegrated sensOstep encoder, S/D input, ext. En-

coder input, 1 analog input, 4 digital inputs, 1 OD

output, CAN, RS485 and USB interfaces

60mm x 60mm x 26mm

TMCM-1260-CANopen 1-axis bipolar stepper motor controller/driver, up-

to 6A RMS motor current, 48V nom. supply, in-

tegrated sensOstep encoder, S/D input, ext. En-

coder input, 1 analog input, 4 digital inputs, 1 OD

output, CAN, RS485 and USB interfaces

60mm x 60mm x 26mm

TMCM-1260-3A-TMCL 1-axis bipolar stepper motor controller/driver, up-

to 6A RMS motor current, 48V nom. supply, in-

tegrated sensOstep encoder, S/D input, 3 analog

inputs, 2 digital inputs, 1 OD output, CAN, RS485

and USB interfaces

60mm x 60mm x 26mm

Table 1: TMCM-1260 Order Code

A cable loom set is available for this module:

Order Code Description

TMCM-1260-CABLE Cable loom for TMCM-1260:

•1x cable loom for power supply connector (cable length 200mm, 4pin

JST VH connector at one end, open wires at other end)

•1x cable loom for RS485 + CAN connector (cable length 200mm, 5pin

JST PH connector at one end, open wires at other end)

•1x cable loom for motor connector (cable length 200mm, 4pin JST EH

connector at one end, open wires at other end)

•1x cable loom for (alternate high power) motor connector (cable

length 200mm, 4pin JST VH connector at one end, open wires at other

end)

•1x cable loom for I/O connector (cable length 200mm, 8pin JST PH

connector at one end, open wires at other end)

•1x Micro-USB cable

Table 2: TMCM-1260 Cable Loom

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 6 / 30

The TMCM-1260 is also available as motor mounted version together with a selection of NEMA23 / NEMA24

ﬂange size stepper motor. Please refer to PD57/60-x-1260 PANdrive hardware manual for further details.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 7 / 30

3 Mechanical and Electrical Interfacing

3.1 Size of board

The board with the controller/driver electronics has an overall size of 60mm x 60mm x 26mm without

mating connectors. Maximum component height without mating connectors is around 21mm above and

3mm below PCB level. There are four mounting holes for M3 screws for mounting the board either to a

NEMA23 (two mounting holes at opposite corners) or a NEMA24 (other two mounting holes at opposite

corners) stepper motor.

Power

RS485 + CAN USB

Motor

I/O

(0/0)

(3.25/13.75)

3.2

(4.6/45.95)

3.2

(56.75/46.25)

3.2

(55.4/14.05)

3.2

(26/58.25)

(3.75/24.05)

(33.75/1.65)

(35.95/8.5)

(58.25/37)

Figure 1: Board dimensions, position of mounting holes and position (pin 1) of connectors (all values in mm)

3.2 Board mounting considerations

The TMCM-1260oﬀers four metal plated mounting holes. All mounting holes are connected to system

and signal ground (same as power supply ground). In order to minimize distortion of signals and radia-

tion of HF signals (improve EMC compatibility) especially in sensitive / noisy environments it is important

to ensure a solid ground connection within the system. In order to support this, it is recommended to

connect mounting holes used for mounting the board to the supply ground connection (in addition to the

ground connection of the power supply connector). Nevertheless, this might not always be an option e.g.

in case the metal system chassis / TMCM-1260mounting plate is already connected to earth and a direct

connection between supply ground (secondary side) and mains supply earth (primary side) is not desired

/ not an option. In this case plastic (e.g. made of nylon) spacers / distance bolts and screws should be

used.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 8 / 30

4 Connectors

The TMCM-1260 oﬀers six connectors altogehter. There is one power supply connector and two interface

connectors - one with ﬁve pins for RS485 and CAN and a dedicated micro-USB connector. All other inputs

and outputs are concentrated on one 8 pin connector. Furthermore, there is one connection for the

stepper motor with four pins with a choice between two connectors with diﬀerent size, pitch and current

rating. While the smaller one supports motor currents up-to 3A RMS (half the max. current of the module)

the larger supports the full current (6A RMS).

NOTICE Start with power supply OFF and do not connect or disconnect motor dur-

ing operation! Motor cable and motor inductivity might lead to voltage spikes

when the motor is (dis)connected while energized. These voltage spikes might ex-

ceed voltage limits of the driver MOSFETs and might permanently damage them.

Therefore, always switch oﬀ / disconnect power supply or at least disable driver

stage before connecting / disconnecting motor.

I/O

RS485 + CAN

1 5

USB

Motor

Power

Figure 2: TMCM-1260 connectors

Connector Types and Mating Connectors

Connector Connector type on-board Mating connector type

Power JST B4P-VH

(JST VH series, 4pins, 3.96mm pitch)

Connector housing: JST VHR-4N

Contacts: JST SVH-21T-P1.1

Wire: 0.83mm2, AWG 18

Motor JST JST B4P-VH

(JST VH series, 4pins, 3.96mm pitch)

JST JST B4B-EH-A

(JST EH series, 4pins, 2.5mm pitch)

Connector housing: JST VHR-4N

Contacts: JST SVH-21T-P1.1

Wire: 0.83mm2, AWG 18

Connector housing: JST EHR-4

Contacts: JST SEH-001T-P0.6

Wire: 0.33mm2, AWG 22

RS485+CAN JST B5B-PH-K-S

(JST PH series, 5pins, 2mm pitch)

Connector housing: JST PHR-5

Contacts: JST SPH-002T-P0.5S

Wire: 0.22mm2, AWG 24

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 9 / 30

Connector Connector type on-board Mating connector type

USB USB-micro B female connector USB-micro B male connector

I/O JST B8B-PH-K-S

(JST PH series, 8pins, 2mm pitch)

Connector housing: JST PHR-8

Contacts: JST SPH-002T-P0.5S

Wire: 0.22mm2, AWG 24

Table 3: Connector Types and Mating Connectors of the TMCM-1260

4.1 Power Supply Input Connector

The TMCM-1260 oﬀers one 4pin JST VH series power supply input connector. In addition to main power

supply input and related ground connection this connector oﬀers a separate logic supply input with the

option to keep the on-board logic alive while the driver stage is switched oﬀ. It is not necesary to connect

the logic supply input in case separate supplies are not required as the main power supply input will

always supply power to the driver stage and the logic part.

The power supply input connector oﬀers a driver enable input. This input has to be connected to any

voltage above 3.5V up-to max. supply voltage of 54V in order to enable the driver stage. Leaving this pin

unconnected or connected to ground (voltage below 2.4V) will disable the driver stage regardless of any

settings in software. This input may be connected to main power supply input permanently in case an

enable input in hardware is not required.

Power Supply Connector Pin Assigment

Pin Label Direction Description

1 GND Power (GND) Common system supply and signal ground

2 VMAIN Power (input) Main power supply input for the driver and on-board logic

12. . . 54V

3 Enable Digital input Driver enable input. A voltage above 3.5V is required here in

order to enable the on-board stepper motor driver. This in-

put maybe connected to main power supply input in order to

enable the driver stage.

4 VLOGIC Power (input) Optional separate power supply input for the on-board logic

12. . . 54V

Table 4: Power Supply Connector Pin Assignment

NOTICE Do not connect or disconnect motor during operation! Motor cable and mo-

tor inductivity might lead to voltage spikes when the motor is (dis)connected

while energized. These voltage spikes might exceed voltage limits of the driver

MOSFETs and might permanently damage them. Therefore, always switch oﬀ

/ disconnect power supply or at least disable driver stage before connecting /

disconnecting motor.

NOTICE Take care of polarity, wrong polarity can destroy the board!

NOTICE Connect Enable pin to voltage >3.5V in order to enable motor movements!

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 10 / 30

4.2 Motor Connector

Two four pin motor connectors are available. Either of them can be used for connecting a bipolar stepper

motor. Both connectors are connected to the same driver stage therefore, just one connector should

be used at the same time. While the more compact 4pin JST EH series connector is suitable for motor

currents up-to 3A RMS the larger JST VH series connector is able to support all motor current up-to 6A

RMS (limit of the unit).

Motor Connector Pin Assignment

Pin Label Direction Description

1 B1 out Pin 1 of motor coil B

2 B2 out Pin 2 of motor coil B

3 A1 out Pin 1 of motor coil A

4 A2 out Pin 2 of motor coil A

Table 5: Motor Connector Pin Assignment

NOTICE Connect just one motor connector at the same time! Both connectors are

connected to the same driver stage.

NOTICE Do not connect or disconnect motor during operation! Motor cable and mo-

tor inductivity might lead to voltage spikes when the motor is (dis)connected

while energized. These voltage spikes might exceed voltage limits of the driver

MOSFETs and might permanently damage them. Therefore, always switch oﬀ

/ disconnect power supply or at least disable driver stage before connecting /

disconnecting motor.

NOTICE Do not mix-up power supply connector and the larger motor connector!

4.3 RS485 + CAN Connector

For serial communication the TMCM-1260 oﬀers selection between RS485, CAN and USB interfaces. While

the USB interface is available for conﬁguration and service of the board, mainly (e.g. parameter settings,

ﬁrmware updates) a 5-pin JST PH series connector oﬀers 2-wire RS485 and CAN interfaces for in system

communication.

NOTICE Due to hardware ressource sharing USB and CAN communication interfaces are

not available at the same time. As soon as USB is physically attached to a host or

hub the CAN interface will be switched oﬀ.

RS485 + CAN Connector Pin Assignment

Pin Label Direction Description

1 GND Power (GND) Common system supply and signal ground

2 RS485+ Bidirectional RS485 interface, diﬀ. signal (non-inverting)

3 RS485- Bidirectional RS485 interface, diﬀ. signal (inverting)

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 11 / 30

Pin Label Direction Description

4 CAN_H Bidirectional CAN interface, diﬀ. signal (non-inverting)

5 CAN_L Bidirectional CAN interface, diﬀ. signal (inverting)

Table 6: RS485 + CAN Connector Pin Assignment

4.4 USB Connector

For serial communication the TMCM-1260 oﬀers selection between RS485, CAN and USB interfaces. The

USB interface via on-board micro-USB connector (type B) is available for conﬁguration and service of the

board, mainly (e.g. parameter settings, ﬁrmware updates). The USB device interface supports full speed

(12Mbit/s) communication and supports bus powered and self-powered operation. During bus-powered

operation the low voltage logic part of the board will be powered, only. This includes the microcontroller

and the non-volatile memory and therefore allows parameter settings and ﬁrmware updates of the board

using a standard USB cable, only. Of course, for any motor movement main supply via supply input

connector is required.

NOTICE Due to hardware ressource sharing USB and CAN communication interfaces are

not available at the same time. As soon as USB is physically attached to a host or

hub the CAN interface will be switched oﬀ.

USB Connector Pin Assignment

Pin Label Direction Description

1 VBUS Power (+5V) USB +5V nom. power supply input

2 D- Bidirectional USB interface, diﬀ. signal (inverting)

3 D+ Bidirectional USB interface, diﬀ. signal (inverting)

4 ID Input connected to GND (via 100k resistor)

5 GND Power (GND) Common system supply and signal ground

Table 7: USB Connector Pin Assignment

4.5 I/O Connector

The TMCM-1260 oﬀers several inputs (two of them optically isolated) and one digital (open-drain) output.

The inputs include support for stop switches (left and right), home switch, step/direction, incremental A/B

channel encoder and analog (0. .. +10V) input. All this functionality is available via one 8pin JST PH series

I/O connector.

USB Connector Pin Assignment

Pin Label Direction Description

1 GND Power (GND) Common system supply and signal ground

2 IN0/HOME Input Analog input (0. . . +10V)

HOME switch input

+24V tolerant, programmable (separate) pull-up to +5V

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 12 / 30

Pin Label Direction Description

3 IN1/ENC_A Input General purpose digital input

Incremental encoder input channel A

+24V tolerant, programmable pull-up (for IN1/IN2 together) to

+5V

4 IN2/ENC_B Input General purpose digital input

Incremental encoder input channel B

+24V tolerant, programmable pull-up (for IN1/IN2 together) to

+5V

5 STOP_L/STEP Input STOP left switch input

STEP pulse input

input optically isolated, +24V compatible

6 STOP_R/DIR Input STOP right switch input

DIR input

input optically isolated, +24V compatible

7 ISO_COM Power Common positive (+24V_ISO) or negative (GND_ISO) isolated

supply input for optically isolated inputs

8 OUT0 Output (OD) Open-Drain output. Output will be pulled low when activated.

Voltages up-to logic supply input level (or main supply input in

case separate logic supply is not used) are supported here. Max.

continuous pull-down current: 100mA

Table 8: I/O Connector Pin Assignment

All pins marked light green oﬀer functional isolation towards main supply input. In case this is not required

ISO_COM may be connected to main ground or supply input, of course. The opto-couppler used are AC

types. This way, either high side switches or low side switches for both inputs are supported.

5 On-Board LEDs

The board oﬀers two LEDs in order to indicate board status. The function of both LEDs is dependent on the

ﬁrmware version. With standard TMCL ﬁrmware the green LED should be ﬂashing slowly during operation

and the red LED should be oﬀ. When there is no valid ﬁrmware programmed into the board or during

ﬁrmware update the red and green LEDs are permanently switched on. During reset to factory default

values the green LED will be ﬂashing fast. With CANopen ﬁrmware both LEDs are switched on/oﬀ/ﬂashing

according to standard deﬁntion.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 13 / 30

Green LEDRed LED

Figure 3: TMCM-1260 LEDs

6 Reset to Factory Defaults

It is possible to reset all settings in ﬁrmware for the TMCM-1260 to factory defaults without establishing

a working communication connection. This might be helpful in case communication parameters of the

preferred interface have been set to unknown values or got lost.

For this procedure two pads on the bottom side of the module have to be shorted (electrically connected

with each other) during power-on.

Please perform the following steps:

1. Switch power supply OFF (and disconnect USB cable if applicable)

2. Short CLK and DIO pads of programming pads on bottom of pcb (see ﬁgure 4)

3. Switch power supply ON again (or connect USB again if applicable)

4. Wait until the on-board red and green LEDs start ﬂashing fast (this might take a while)

5. Switch power supply OFF again (and disconnect USB cable if applicable)

6. Remove short between pads

7. After switching power supply ON again (and / or connecting USB cable) all permanent settings have

been restored to factroy defaults

Short these two pads

Figure 4: Reset to factory default settings

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 14 / 30

7 I/Os

The I/O connector (8pin JST PH series) oﬀers one analog input, two non-isolated digital inputs with inte-

grated pull-ups (programmable) and two optically isolated inputs. All inputs can be used for diﬀerent

purposes explained in more detail in the following subsections.

7.1 Analog input IN0

The TMCM-1260 oﬀers one analog input. The analog input voltage range is approx. 0..+10V. For volt-

ages above +10V saturation takes place but, up-to 30V higher voltages are tolerated without destroying

the input. For analog to digital conversion the integrated ADC of the on-board microcontroller is used.

Resolution of this converter is 12bit (0..4095).

100nF

10k

22k

2k2

+3V3

microcontroller

IN0

+5V

TMCM-1260

pull-up

disabled

0..10V

Figure 5: Analog input IN0

The analog input can be used as digital input, also. There is an integrated pull-up to +5V which can be

switched on of oﬀ in software. When using this input as anlog input the pull-up should be usually switched

oﬀ.

7.2 Digital inputs IN1 and IN2

The TMCM-1260 oﬀers two digital inputs IN1 and IN2 which accept signals between 0 and 30V with volt-

ages above approx. 2.9V recognized as logical ’1’ and below 1V as logical ’0’. Both inputs oﬀer intergated

pull-ups to +5V which can be switched on or oﬀ in software (always together). When using the inputs with

low-side switches (connected to GND), pull-ups usually should be switched on (default). In case high-side

switches are used the pull-ups must be switched oﬀ. For push-pull signals the pull-ups may be either

switched on or oﬀ.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 15 / 30

33pF

22k

10k

2k2

+3V3

microcontroller

IN1

IN2

+5V

TMCM-1260

pull-up

enabled

pull-up

disabled

+5V...24V

+5V

Figure 6: Digital inputs IN1 and IN2

7.3 HOME/STOP_L/STOP_R switch inputs

The TMCM-1260 oﬀers two optically isolated inputs which can be used as left (STOP_L) and right (STOP_R)

stop switch inputs. When enabled in software the STOP_L switch input will stop motor movement in

negative direction (step counter decreasing) while activated. Likewise the STOP_R switch input will stop

motor movement in positive direction (step counter increasing) while activated.

680

6k8

2k2

+3V3

microcontroller

TMCM-1260

STOP_L,

STOP_R

ISO_COM

+24V_ISO

GND_ISO

+24V_ISO

GND_ISO

Figure 7: Stop switch inputs

A separated / isolated supply may be used for the switches - as indicated in the drawing (+24V_ISO and

related GND_ISO) - but, same supply as for the TMCM-1260 can be used, also, of course.

7.4 External incremental encoder input

The TMCM-1260 oﬀers an integrated hall-sensor based magnet encoder. In addition, an external incre-

mental A/B encoder may be connected to the two digital inputs IN1 and IN2. Encoder with push-pull

signals (e.g. +5V TTL) and open-drain output signals are supported (single-ended). For open-drain out-

puts the internal pull-ups should be activated in software (default mode).

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 16 / 30

33pF

22k

10k

2k2

+3V3

microcontroller

ENC_A,

ENC_B

+5V

TMCM-1260

+5V

pull-up

enabled

Figure 8: External encoder input

7.5 Step/Direction inputs

The TMCM-1260 may be used as driver with an external motion controller. In this case the Step/Direction

output signals of the external motion controller may be connected to the optically isolated Step/Dir inputs

of the TMCM-1260. Please note that these signals should be 24V signals. For lower voltage signals a simple

small signal transistor maybe inserted as level converter.

680

6k8

2k2

+3V3

microcontroller

TMCM-1260

STEP,

DIR

ISO_COM

+24V_ISO

GND_ISO

Figure 9: Step/Direction input

Due to limitations of the opto-isolators the maximum step frequency of these inputs is limited to around

20kHz. For higher motor speed the step interpolator of the driver stage should be activated or the mi-

crostep resolution reduced (default 256 microsteps per fullstep).

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 17 / 30

8 Communication

8.1 RS485

For remote control and communication with a host system the TMCM-1260 provides a two wire RS485

bus interface. For proper operation the following items should be taken into account when setting up an

RS485 network:

1. BUS STRUCTURE:

The network topology should follow a bus structure as closely as possible. That is, the connection

between each node and the bus itself should be as short as possible. Basically, it should be short

compared to the length of the bus.

c:> node

node

n- 1

node

Host Slave Slave Slave

RS485

termination

resistor

(120 Ohm)

termination

resistor

(120 Ohm)

}

keep distance as

short as possible

Figure 10: RS485 bus structure with termination resistors

2. BUS TERMINATION:

Especially for longer busses and/or multiple nodes connected to the bus and/or high communication

speeds, the bus should be properly terminated at both ends. The TMCM-1260 does not integrate

any termination resistor. Therefore, 120 Ohm termination resistors at both ends of the bus have to

be added externally.

3. NUMBER OF NODES:

The RS485 electrical interface stadard (EIA-485) allows up to 32 nodes to be connected to a single bus.

The bus transceiver used on the TMCM-1260 units (SN65HVD1781D) oﬀers a signiﬁcantly reduced

bus load compared to the standard and allows a maximum of 255 units to be connected to a single

RS485 bus using standard TMCL ﬁrmware. Please note: usually it cannot be expected to get reliable

communication with the maximum number of nodes connected to one bus and maximum supported

communication speed at the same time. Instead, a compromise has to be found between bus cable length,

communication speed and number of nodes.

4. COMMUNICATION SPEED:

The maximum RS485 communication speed supported by the TMCM-1260 hardware is 1Mbit/s. Fac-

tory default is 9600 bit/s. Please see separate TMCM-1260 TMCL ﬁrmware manual for information

regarding other possible communication speeds below the upper hardware limit.

5. NO FLOATING BUS LINES:

Avoid ﬂoating bus lines while neither the host/master nor one of the slaves along the bus line is

transmitting data (all bus nodes switched to receive mode). Floating bus lines may lead to communi-

cation errors. In order to ensure valid signals on the bus it is recommended to use a resistor network

connecting both bus lines to well deﬁned logic levels.

There are actually two options which can be recommended: Add resistor (bias) network on one side

of the bus, only (120R termination resistor still at both ends):

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 18 / 30

node

n- 1

node

Slave Slave

termination

resistor

(120R)

+5V

GND

pull-up (680R)

pull-down (680R)

RS485- / RS485B

termination

resistor

(120R)

RS485+ / RS485A

Figure 11: RS485 bus lines with resistor (bias) network on one side, only

Or add resistor network at both ends of the bus (like Proﬁbus™termination):

node

n- 1

node

Slave Slave

termination

resistor

(220R)

+5V

GND

pull-up (390R)

pull-down (390R)

RS485- / RS485B

RS485+ / RS485A

termination

resistor

(220R)

+5V

GND

pull-up (390R)

pull-down (390R)

Figure 12: RS485 bus lines with Proﬁbus™recommended line termination

8.2 CAN

For remote control and communication with a host system the TMCM-1260 provides a CAN bus interface.

Please note that the CAN interface is not available in case USB is connected. For proper operation the

following items should be taken into account when setting up a CAN network:

1. BUS STRUCTURE:

The network topology should follow a bus structure as closely as possible. That is, the connection

between each node and the bus itself should be as short as possible. Basically, it should be short

compared to the length of the bus.

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 19 / 30

c:> node

node

n- 1

node

Host Slave Slave Slave

CAN

termination

resistor

(120 Ohm)

termination

resistor

(120 Ohm)

}

keep distance as

short as possible

Figure 13: CAN bus structure with termination resistors

2. BUS TERMINATION:

Especially for longer busses and/or multiple nodes connected to the bus and/or high communication

speeds, the bus should be properly terminated at both ends. The TMCM-1260 does not integrate

any termination resistor. Therefore, 120 Ohm termination resistors at both ends of the bus have to

be added externally.

3. BUS TERMINATION:

The bus transceiver used on the TMCM-1260 units (TJA1051T) supports at least 110 nodes under

optimum conditions. Practically achievable number of nodes per CAN bus highly depend on bus

length (longer bus -> less nodes) and communication speed (higher speed -> less nodes).

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

TMCM-1260 Hardware Manual •Hardware Version V1.10 | Document Revision V1.31 •2021-AUG-18 20 / 30

9 Motor driver current

The on-board stepper motor driver operates current controlled. The driver current may be programmed

in software with 32 eﬀective scaling steps in hardware.

Explanation of diﬀerent columns in table below:

Motor current set-

ting in software

(TMCL)

These are the values for TMCL axis parameter 6 (motor run current) and

7 (motor standby current). They are used to set the run / standby current

using the following TMCL commands:

(read-out value with GAP instead of SAP. Please see separate TMCM-1260

ﬁrmware manual for further information)

Motor current IRMS

[A] Resulting motor current based on motor current setting

Available motor current settings

Motor current setting

in software (TMCL)

Current scaling step

(CS)

Motor current ICOIL[A]

peak

Motor current ICOIL[A]

RMS

0. . . 7 0 0.254 0.180

8. . . 15 1 0.508 0.359

16. . . 23 2 0.762 0.539

24. . . 31 3 1.016 0.718

32. . . 39 4 1.270 0.898

40. . . 47 5 1.523 1.077

48. . . 55 6 1.777 1.257

56. . . 63 7 2.031 1.436

64. . . 71 8 2.285 1.616

72. . . 79 9 2.539 1.795

80. . . 87 10 2.793 1.975

88. . . 95 11 3.047 2.154

96. . . 103 12 3.301 2.334

104. . . 111 13 3.555 2.514

112. . . 119 14 3.809 2.693

120. . . 127 15 4.063 2.873

128. . . 135 16 4.316 3.052

136. . . 143 17 4.570 3.232

144. . . 151 18 4.824 3.411

152. . . 159 19 5.078 3.591

Terms of delivery and rights to technical change reserved.

Download newest version at www.trinamic.com

Page is loading ...

Trinamic TMCM-1260-CANopen Owner's manual

Brand: Trinamic

Model: TMCM-1260-CANopen

Type: Owner's manual

This manual is also suitable for

TMCM-1260-TMCL

Download PDF

report

Trinamic TMCM-1260-CANopen Owner's manual

This manual is also suitable for

Trinamic TMCM-1260-CANopen Owner's manual

Related papers

Other documents