Renkforce Presenter Owner's manual

Brand: Renkforce

Model: Presenter

Type: Owner's manual

b) Laser

• When operating the laser equipment, always make sure that the laser beam is

directed so that no one is in the projection area and that unintentionally reected

beams (e.g. from reective objects) cannot be directed into areas where people

are present.

• Laser radiation can be dangerous if the laser beam or its reection enters

unprotected eyes. Before using the product, familiarise yourself with the statutory

regulations and instructions for operating this type of laser device.

• Never look into the laser beam or point it at people or animals. Laser radiation can

seriously damage your eyes.

• If laser radiation enters your eyes, close your eyes immediately and move your

head away from the beam.

• If your eyes have been irritated by laser radiation, do not continue to carry out

tasks with safety implications, such as working with machines, working from

heights or working close to high voltages. Do not drive any vehicles until the

irritation has completely subsided.

• Do not point the laser beam at mirrors or other reective surfaces. The uncontrolled,

reected beam may strike people or animals.

• Never open the device. Conguration or maintenance tasks must only be

completed by a trained specialist who is familiar with the potential hazards.

Improper maintenance work may result in dangerous laser radiation.

• The product is equipped with a class 2 laser. Laser signs in different languages

are included in the packaging. If the sign on the laser is not in your local language,

attach the appropriate sign to the laser.

ATTENTION

LASER RADIATON

DO NOT STARE INTO THE BEAM

CLASS 2 LASER PRODUCT

Max Output: <1mW

Wavelength: 650nm

EN 60825-1:2014

• Caution: Using equipment or procedures other than those described in these

instructions could lead to exposure to dangerous radiation.

c) LiPo battery

• The rechargeable battery is permanently built into the product and cannot be

replaced.

• Never damage the rechargeable battery. Damaging the casing of the rechargeable

battery might cause an explosion or a re! Unlike conventional batteries/

rechargeable batteries (e.g. AA or AAA type), the casing of the LiPo rechargeable

battery does not consist of a thin sheet but rather a sensitive plastic lm only.

• Never short-circuit the contacts of the rechargeable battery. Do not throw the

battery or the product into re. There is a danger of re and explosion!

• Charge the rechargeable battery regularly, even if you do are not using the

product. Due to the rechargeable battery technology being used, you do not need

to discharge the rechargeable battery rst.

• Never charge the rechargeable battery of the product unattended.

• When charging, place the product on a surface that is not heat-sensitive. It is

normal that a certain amount of heat is generated during charging.

Overview

1 Laser pointer

2 LED indicator

3 Laser button

4 button (previous page)

5 button (next page)

6 Play/Esc button (long press black

screen)

7 ON / OFF switch

8 USB-C

charging port

9 + button (increase volume)

10 - button (decrease volume)

Operating instructions

Bluetooth Presenter RF-MP-R250BT

Item No. 2144002

Intended use

The presenter is designed to point out details on objects and display boards and connects to

compatible devices via Bluetooth. It is powered by a built-in rechargeable battery and has a

USB type-C

charging port.

This product is intended for indoor use only. Do not use it outdoors. Contact with moisture (e.g.

in bathrooms) must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. Using the

product for purposes other than those described above may damage the product. In addition,

improper use can cause hazards such as a short circuit or re. Read the instructions carefully

and store them in a safe place. Only make this product available to third parties together with

its operating instructions.

This product complies with statutory, national and European regulations. All company and

Package contents

• Bluetooth presenter

• USB-A to USB-C

charging cable (15cm)

• Operating instructions

Up-to-date operating instructions

Download the latest operating instructions at www.conrad.com/downloads or scan the QR code

shown. Follow the instructions on the website.

Explanation of symbols

The symbol with an exclamation mark in a triangle is used to highlight important

information in these operating instructions. Always read this information carefully.

The arrow symbol indicates special information and advice on how to use the

product.

Safety instructions

Read the operating instructions and safety information carefully. If you do

not follow the safety instructions and information on proper handling in

these operating instructions, we will assume no liability for any resulting

personal injury or damage to property. Such cases will invalidate the warranty/

guarantee.

a) General information

• The product is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. It may become a

dangerous toy for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed

if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Handle the product carefully. Jolts, impacts or a fall even from a low height may

damage the product.

• Always observe safety and operating instructions of any other devices which are

connected to the product.

• Consult a technician if you are not sure how to use or connect the product, or if

you have concerns about safety.

• Maintenance, modications and repairs must be done by a technician or an

authorized repair center.

• If you have questions which remain unanswered by these operating instructions,

contact our technical support service or other technical personnel.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method (e.g. photocopying, microlming or capturing in

electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is

prohibited. This publication reects the technical state at the time of printing.

Charging the Battery

Charge the battery before using the product for the rst time.

The LED indicator (2) ashes red when there is insufcient battery power remaining. When this

occurs, follow the steps below to recharge the battery:

• Insert the USB-C

plug on the USB cable into the USB-C

charging port (8) on the product.

• Connect the USB-A connector on the

cable to a USB port on a computer or another suitable

USB power source, such as a USB power adapter.

• The LED indicator (2) will ash red/blue to indicate that the battery is charging. After a few

minutes, the LED indicator (2) will switch to constant blue to indicate that the battery status

is no longer critically low.

Depending on the remaining battery level, the battery takes approximately 1 hour to

charge.

• An overcharging function prevents the battery from overcharging. Charging stops

automatically when the battery voltage is greater than 3.7 V.

• Disconnect the product from the USB power source when the battery is fully charged. The

device is now fully charged and ready for use.

Operation

a) Power ON / OFF

Slide the power switch (7) to the ON position to begin use.

Slide the power switch (7) to the OFF position when nished using.

b) Button functions

Button Function

Press and hold to activate the laser pointer, and release to deactivate. The LED

indicator (2) will turn red when the laser is on.

Press to return to the previous page.

Press to go the next page.

Press to start or stop a “slideshow”.

Press and hold for “black screen”, press to return to presentation.

+ Press to increase the volume.

- Press to decrease the volume.

c) Bluetooth Pairing

• Activate Bluetooth on your host device.

• Press the button (4) and button (5) at the same time. The LED indicator (2) will blink red

to indicate it is ready to be paired.

• On your host device, search for “R250BT”. When the LED indicator (2) stops blinking, pairing

is complete.

• The presenter is now ready for use.

d) Using the presenter with a supported application

The presenter provides full functionality for “MS PowerPoint, Apple

Keynote”. For “Google

Slides” the blackout screen function is not supported.

• Slide the switch (7) to the ON position to turn the power on.

• Launch your presentation software, and open the desired presentation le:

- Press (6) to start a slideshow.

- Press (4) or (5) to change slides.

- Press (6) to exit slideshow.

Care and cleaning

• Always disconnect the product from the power supply before cleaning it.

• Slide the power switch (7) to the OFF position.

• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may

damage the housing or cause the product to malfunction.

• Use a dry, lint-free cloth to clean the product.

Declaration of Conformity (DOC)

Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declares that this

product conforms to Directive 2014/53/EU.

Click on the following link to read the full text of the EU declaration of conformity:

www.conrad.com/downloads

Select a language by clicking on the corresponding ag symbol, and then enter

the product order number in the search box. The EU Declaration of Conformity is

available for download in PDF format.

Disposal

Electronic devices are recyclable waste and must not be placed in household waste.

At the end of its service life, dispose of the product according to the relevant statutory

regulations. You thus full your statutory obligations and contribute to protection of

the environment.

Technical data

Input voltage ................................. 5 V/DC. 500 mA via USB-C

Rechargeable battery ................... LiPo 3.7 V, 300 mAh (built-in)

Charging time ............................... 1 hour

Battery life ..................................... Approx. 30 hours (when fully charged)

Power ........................................... 7 mA

Laser class ................................... 2

Laser wavelength ......................... 650 nm

Laser power .................................. <1 mW

Bluetooth ...................................... 5.1

Bluetooth name ............................ R250BT

Transmission distance .................. Approx. 15 meters

Transmission frequency................ 2.403-2.475 GHz

Transmission power...................... 0 dBm

Supported applications ................. MS PowerPoint, Apple

Keynote, Google Slides

Supported operating systems ....... Windows

98 (and above)

Mac OS 10.4 (and above)

Operating conditions ..................... -10 to +45 °C, 10–85 %

relative humidity (non-condensing)

Storage conditions ........................ -20 to +80 °C, 10–85 %

relative humidity (non-condensing)

Dimensions (W x H x D) .............. 135 x 28 x 12 mm

Weight .......................................... 55 g

Renkforce Presenter Owner's manual

Renkforce Presenter Owner's manual

Renkforce Presenter Owner's manual

Related papers

Other documents