OJ Electronics WLOC3-19 Operating instructions

OJ Electronics
Brand
OJ Electronics
Model
WLOC3-19
Type
Operating instructions

OJ Electronics WLOC3-19 is an outdoor compensation module that can be used for compensated control of hydronic floor heating and cooling. It is a digital outdoor temperature sensor that connects to a 2-wire, 5V communication bus. The module is maintenance-free and has an IP44 enclosure rating.

Here are some of the key features and possible use cases of the OJ Electronics WLOC3-19:

  • Weather compensation: The module can be used to compensate for changes in outdoor temperature, which can help to improve the efficiency of your heating or cooling system.
  • Easy installation: The module is easy to install and can be mounted directly on a wall.

OJ Electronics WLOC3-19 is an outdoor compensation module that can be used for compensated control of hydronic floor heating and cooling. It is a digital outdoor temperature sensor that connects to a 2-wire, 5V communication bus. The module is maintenance-free and has an IP44 enclosure rating.

Here are some of the key features and possible use cases of the OJ Electronics WLOC3-19:

  • Weather compensation: The module can be used to compensate for changes in outdoor temperature, which can help to improve the efficiency of your heating or cooling system.
  • Easy installation: The module is easy to install and can be mounted directly on a wall.
INSTRUCTIONS
© 2017 OJ Electronics A/S
1
Waterline Outdoor Compensation Module
English
Product programme
WLOC3-19 Outdoor Compensation Module
Introduction
WLM3-1FS and WLM3-3FS masters are supplied pre-prepared for weather
compensation and simply by adding an outdoor compensation module on
the 2-wire bus and using a water temperature sensor on the supply water
side your control system can be weather compensated.
Preset values are factory programmed but can easily be changed adjusted
according to local needs via the display on the master. Please refer to the
section titled "Master with Display Type WLM3" in the User Manual for
instructions on changing the default factory settings. The User Manual is
supplied with the master (WLM3).
Mounting of outdoor compensation module
The unit should be mounted under the eaves of the roof or, alternatively,
2-3 metres above ground level. Direct sunlight or other heat sources, e.g.
ventilation vents, must be avoided. The unit should be mounted vertically
with the cable entry downwards.
Fig. 1
BR939A09A
Outdoor compensation module - bus connection
Only OJ units which are suitable for two-wire communication can be
used. Standard installation cable of minimum 2 x 0.25 mm² can be used.
Units can be connected in conventional star formation or in bus mode
(daisy chain). The master has four sets of terminals marked SENSOR/
CONTROLLER BUS that can be used for connecting the 2-core signal
cable from the unit.
Any unit can be connected to any pair of terminals. The total length of
the 2-wire system can be up to 300 m with a maximum length of 100 m
between any two units. For further information, see the table below.
Remember to connect + to + and – to – .
67342A 03/17 (HKT)
• English
• Polski
• Norsk
• Deutsch
Fig. 2
BR939A10A
Sensors and outdoor compensation module connected in bus mode (daisy
chain)
Fig. 3
BR939A11A
Sensors and outdoor compensation module connected in star formation
Maintenance
The unit is maintenance free.
Certifications
CE marking
OJ Electronics A/S hereby declares that the product conforms with the
following Directives of the European Parliament and of the Council:
• EMC - electromagnetic compatibility
• RoHS - restriction on the use of certain hazardous substances
• WEEE - waste electrical and electronic equipment
Applied standard(s)
EN 61000-6-2, EN 61000-6-3
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

OJ Electronics WLOC3-19 Operating instructions

OJ Electronics
Brand
OJ Electronics
Model
WLOC3-19
Type
Operating instructions

OJ Electronics WLOC3-19 is an outdoor compensation module that can be used for compensated control of hydronic floor heating and cooling. It is a digital outdoor temperature sensor that connects to a 2-wire, 5V communication bus. The module is maintenance-free and has an IP44 enclosure rating.

Here are some of the key features and possible use cases of the OJ Electronics WLOC3-19:

  • Weather compensation: The module can be used to compensate for changes in outdoor temperature, which can help to improve the efficiency of your heating or cooling system.
  • Easy installation: The module is easy to install and can be mounted directly on a wall.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers