Comelit 8461MB Owner's manual

Brand: Comelit

Model: 8461MB

Type: Owner's manual

This manual is also suitable for

8461M

TECHNICAL

MANUAL

Technical manual for single-family KIT

Art. 8461M, 8461MB

Passion.Technology.Design.

Warning

• Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the

standards in force. Do not tamper with the internal elements offering protection against short circuits and overcurrents.

• All the equipment must only be used for the purpose it was designed for. Comelit Group S.p.A. declines any

responsibility for improper use of the apparatus, for any alterations made by others for any reason or for the use of

non-original accessories or materials.

• All the products comply with the requirements of the 2014/30/UE, 2014/35/UE directives, as certified by the CE mark

they carry.

• Do not route the riser wires in proximity to power supply cables (230/400V).

• Do not insert objects or pour liquids into the device.

• Installation, mounting and assistance procedures for electrical devices must only be performed by specialised

electricians.

• Cut off the power supply before carrying out any maintenance work.

• Do not press and hold the audio hook while the handset is lifted.

• The camera must not be installed opposite bright light sources, or in places where the filmed subject is against the

light. To resolve the aforementioned problem, we recommend changing the installation height of the camera.

• Cameras with colour sensor have poorer sensitivity in low light conditions than black/white cameras. We therefore

recommend, in dimly lit environments, to install an additional light source.

• IMPORTANT: to prevent a malfunction of the device, make sure that the metal fascia of Art. 4893 does not rub against

any other metal parts and damage their insulation.

Table of contents

Warning ............................................................................................ 2

Package Contents ........................................................................... 4

Operating distances ........................................................................ 5

Power supply unit Art. 1209 ............................................................ 6

Description ...............................................................................................6

External unit Art. 4893 ..................................................................... 7

Description ...............................................................................................7

Installation ................................................................................................8

External unit settings .............................................................................10

Call address programming for 2-4 users

and additional external unit ................................................................... 11

Programming a generic call address ...................................................12

Riser addresses ......................................................................................13

Description of Monitor Art. 6700W and Art. 6701W.................... 14

Soft-touch keys description .................................................................. 15

Indicator LED description......................................................................15

Installation ...................................................................................... 16

Removing / Fitting the terminal ............................................................17

Fitting upgrade KIT Art. 6733W ............................................................. 17

Monitor conﬁguration ................................................................... 18

Standard conﬁguration for soft-touch keys ........................................18

Advanced monitor conﬁguration ..........................................................19

Warning ............................................................................................. 19

Programming for intercom call ..........................................................19

Programming/deleting intercom address ..................................19

Programming buttons for intercom call .....................................20

Direct programming of intercom call .........................................21

Programming keys for generic or coded actuator ............................22

Programming buttons for other functions ......................................... 23

Programming range ..........................................................................24

Monitor ringtone selection ................................................................24

Programming reset ...........................................................................25

Operation ........................................................................................ 26

To make a call from an external unit ....................................................26

Self-ignition .............................................................................................26

Operation with additional internal units ............................................... 26

Operation with additional external units .............................................. 26

Additional door-entry phones Art. 2638 ...................................... 27

Installation of door-entry phone Art. 2638 ........................................... 28

Programming of door-entry phone Art. 2638.......................................28

Wiring diagrams............................................................................. 29

KIT 8461M-MB: standard single-family system.

Switching on/voltage check with system in standby .........................29

KIT 8461M-MB: expansion for two-family system ..............................30

KIT 8461M-MB: expansion for 4-user system .....................................31

KIT 8461M-MB: expansion with second external unit 4893 and

switching device Art. 1405 ....................................................................32

KIT 8461M-MB: expansion with 3 external units 4893

and switching device Art. 1404 .............................................................33

Wiring diagram for system with 2 single-family KITS

KIT 8461M-MB and main external unit Art. 4893 ................................. 34

KIT 8461M-MB: additional actuator relay Art. 1256 ............................35

KIT 8461M-MB: additional remote camera module Art. 1409 ............36

KIT 8461M-MB: additional 2 secondary monitors in cascade

connection ..............................................................................................37

Connection diagram for two-family system with one main monitor

and 2 secondary monitors (cascade connection) ............................... 37

Connection diagram for system with maximum expansion

in branch connection for single call address ......................................38

Connection diagram for cascade connection from internal video unit

of additional door-entry phones Art. 2610 and Art. 6228(B)(W) .........38

Connection diagram for branch connection from internal video unit

of additional door-entry phones Art. 2610 and Art. 6228(B)(W) .........38

Connection diagram for branch connection from riser of additional

door-entry phones Art. 2628/2638 and Art. 6228(B)(W) ......................39

Door open indication use variant..........................................................39

Variant with security door lock and additional power supply ............ 40

Floor door call connection variant........................................................40

Using the RC network for door lock ﬁlter on relay contacts .............40

Package Contents

The KIT components are supplied preconﬁgured for use with the basic version; this manual also includes information for any

system conﬁguration and customisation perceived as necessary by the installer.

6701W-6700W (/BM) 12094893

8461M-8461MB (/BM)

×1

Replaceable nameplates

for 1 user

for 2 users for 3 users

×1 ×1 ×1 ×3 ×3

4893 External unit

1214-2C

×1 ×1

×4

×1

6701W-6700W (/BM) - Monitor

×1

×2

×1

L2L L1N

1209 - Power supply unit

Technical manual

MANUALE

TECNICO

TECHNICAL

MANUAL

MANUEL

TECHNIQUE

TECHNISCHE

HANDLEIDING

TECHNISCHES

HANDBUCH

MANUAL

TÉCNICO

MANUAL

TÉCNICO

Passion.Technology.Design.

Manuale tecnico kit monofamiliare Art. 8461M, 8461MB

Avvertenze

• Eettuare l’installazione seguendo scrupolosamente le istruzioni fornite dal

costruttore ed in conformità alle norme vigenti. Non manomettere le protezioni

interne contro cortocircuiti e sovracorrenti.

• Tutti gli apparecchi devono essere destinati esclusivamente all’uso per cui sono

stati concepiti. Comelit Group S.p.A. declina ogni responsabilità per un utilizzo

improprio degli apparecchi, per modiﬁche eettuate da altri a qualunque titolo e

scopo, per l’uso di accessori e materiali non originali.

• Tutti i prodotti sono conformi alle prescrizioni delle direttive 2014/30/UE, 2014/35/

UE e ciò è attestato dalla presenza della marcatura CE sugli stessi.

• Evitare di porre i ﬁli di montante in prossimità di cavi di alimentazione (230/400V).

• Non inserire oggetti né versare liquidi all’interno del dispositivo.

• Gli interventi di installazione, montaggio e assistenza agli apparecchi elettrici

devono essere eseguiti esclusivamente da elettricisti specializzati.

• Togliere l’alimentazione prima di eettuare qualsiasi manutenzione.

• .atavellos attenroc al noc acinof oicnag li otumerp erenet noN

• La telecamera non deve essere installata di fronte a grandi sorgenti luminose,

oppure in luoghi dove il soggetto ripreso rimanga molto in controluce. Per risolvere

il problema precedentemente descritto, si consiglia di modiﬁcare l’altezza di

installazione della telecamera.

• Le telecamere con sensore a colori, presentano in condizioni di scarsa luminosità,

una sensibilità inferiore rispetto alle telecamere in bianco e nero. Si consiglia

pertanto, in ambienti poco illuminati di prevedere una fonte di illuminazione

aggiuntiva.

• IMPORTANTE: per non compromettere il funzionamento del dispositivo assicurarsi

che il frontale

in metallo dell'articolo 4893 non sfreghi su altre parti metalliche

danneggiando il proprio rivestimento isolante.

Technical manual for single-family kit Art. 8461M, 8461MB

Warning

• Install the equipment by carefully following the instructions given by the

manufacturer and in compliance with the standards in force. Do not tamper with

the internal elements oering protection against short circuits and overcurrents.

• All the equipment must only be used for the purpose it was designed for. Comelit

Group S.p.A. declines any responsibility for improper use of the apparatus,

for any alterations made by others for any reason or for the use of non-original

accessories or materials.

• All the products comply with the requirements of the 2014/30/UE, 2014/35/UE

directives, as certiﬁed by the CE mark they carry.

• Do not route the riser wires in proximity to power supply cables (230/400V).

• Do not insert objects or pour liquids into the device.

• Installation, mounting and assistance procedures for electrical devices must only

be performed by specialised electricians.

• Cut o the power supply before carrying out any maintenance work.

• Do not press and hold the audio hook while the handset is lifted.

• The camera must not be installed opposite bright light sources, or in places where

the ﬁlmed subject is against the light. To resolve the aforementioned problem, we

recommend changing the installation height of the camera.

• Cameras with colour sensor have poorer sensitivity in low light conditions than

black/white cameras. We therefore recommend, in dimly lit environments, to install

an additional light source.

• IMPORTANT: to prevent a malfunction of the device, make sure that the metal

fascia of Art. 4893 does not rub against any other metal parts and damage their

insulation.

Manuel technique kit un appel Art. 8461M, 8461MB

Avertissements

• Eectuer

l'installation en suivant scrupuleusement les instructions fournies par

le constructeur et conformément aux normes en vigueur. Ne pas toucher les

protections internes contre les courts-circuits et les surcharges.

• Tous les appareils doivent être strictement destinés à l'emploi pour lequel ils ont

été conçus. La société Comelit Group S.p.A. décline toute responsabilité en cas

de mauvais usage des appareils, pour des modiﬁcations eectuées par d’autres

personnes pour n’importe quelle raison et pour l'utilisation d’accessoires et

matériaux non d'origine.

• Tous les produits sont conformes aux prescriptions des directives 2014/30/UE,

2014/35/UE. L'application du marquage CE atteste cette conformité.

• Éviter de placer les ﬁls de montant à proximité des câbles d'alimentation

(230/400V).

• Ne jamais introduire d'objets ni verser de liquides à l'intérieur du dispositif.

• Les interventions d'installation, de montage et d'assistance aux appareils

électriques sont réservées à des électriciens spécialisés.

• Couper l'alimentation avant d'eectuer toute opération d'entretien.

• Ne pas maintenir le crochet phonie enfoncé lorsque le combiné est décroché.

• Installeer de camera niet tegenover felle lichtbronnen of op plaatsen waar de

opgenomen persoon met de rug naar het licht staat. Om het hierboven beschreven

probleem op te lossen, is het raadzaam de installatiehoogte van de camera aan

te passen.

• Camera's met kleurensensor hebben in schaars verlichte omstandigheden een

lagere gevoeligheid dan zwart-witcamera's. Het is daarom raadzaam om in

schaars verlichte omgevingen een extra lichtbron te plaatsen.

• IMPORTANT : pour ne pas compromettre le fonctionnement du dispositif,

s'assurer que la façade en métal de l'article 4893 n'entre pas en contact avec

d'autres parties métalliques, ce qui risquerait d'endommager son revêtement

isolant.

Technische handleiding enkelvoudige installatiekit Art. 8461M, 8461MB

Waarschuwingen

• Voer de installatiewerkzaamheden zorgvuldig uit volgens de door de fabrikant

geleverde instructies en met inachtneming van de geldende normen. De interne

beveiligingen tegen kortsluiting en overstroom niet forceren.

• Alle apparaten mogen alleen gebruikt worden voor het beoogde doel waarvoor

ze zijn ontworpen. Comelit Group S.p.A. is niet verantwoordelijk voor oneigenlijk

gebruik van de apparatuur, voor wijzigingen die om welke reden dan ook door

derden zijn aangebracht, en voor het gebruik van accessoires en materialen die

niet door de fabrikant zijn aangeleverd.

• Alle producten voldoen aan de eisen van de richtlijn 2014/30/UE, 2014/35/UE. Dit

wordt bevestigd door het CE-label op de producten.

• Monteer de draden van de stamleiding niet in de buurt van voedingskabels

(230/400V).

• Voorkom het binnendringen van vreemde voorwerpen of vloeistoen in het toestel.

• De installatie-, montage- en servicewerkzaamheden aan de elektrische apparaten

mogen uitsluitend door gespecialiseerde elektriciens worden verricht.

• Sluit de voeding af voordat u onderhoudswerkzaamheden uitvoert.

• Houd de telefoonhaak niet ingedrukt als de hoorn is opgenomen.

• Installeer de camera niet tegenover felle lichtbronnen of op plaatsen waar de

opgenomen persoon met de rug naar het licht staat. Om het hierboven beschreven

probleem op te lossen, is het raadzaam de installatiehoogte van de camera aan

te passen.

• Camera's met kleurensensor hebben in schaars verlichte omstandigheden een

lagere gevoeligheid dan zwart-witcamera's. Het is daarom raadzaam om in

schaars verlichte omgevingen een extra lichtbron te plaatsen.

• BELANGRIJK: om de werking van het toestel niet in gevaar te brengen, dient

u ervoor te zorgen dat

het metalen frontpaneel, Art. 4893, niet over de andere

metalen onderdelen schuurt en daarmee de isolerende bekleding beschadigt.

Technisches Handbuch Kit Einteilnehmerinstallation Art. 8461M, 8461 MB

Hinweise

• Der Einbau muss strikt nach Herstelleranweisungen und unter Einhaltung

der einschlägigen Vorschriften erfolgen. Nicht den internen Kurzschluss- und

Überlastungsschutz verändern.

• Alle Geräte dürfen nur für den Zweck eingesetzt werden, für den sie entwickelt

worden sind. Comelit Group S.p.A. übernimmt keine Haftung für unsachgemäßen

Gebrauch der Geräte, für durch Dritte vorgenommene Änderungen oder die

Verwendung von Nicht-Original-Zubehör und -Ersatzteilen.

• Alle unsere Produkte erfüllen die Anforderungen der Richtlinie 2014/30/UE,

2014/35/UE, was durch die CE-Kennzeichnung bestätigt wird.

• Die Kabel der Steigleitung nicht in Nähe der Stromkabel (230/400 V) verlegen.

• Keine spitzen Gegenstände in das Gerät einführen und dieses gegen das

Eindringen von Flüssigkeiten schützen.

• Installation, Einbau und Wartung der elektrischen Geräte dürfen nur von einem

Elektrofachmann ausgeführt werden.

• Vor Wartungseingrien immer die Stromversorgung unterbrechen.

• Die Telefongabel bei abgehobenem Hörer nicht gedrückt halten.

• Die Kamera darf nicht vor großen Lichtquellen oder an Stellen installiert werden,

an denen das Motiv zu sehr im Gegenlicht steht. Zur Lösung des Problems ist es

angebracht, die Installationshöhe der Kamera zu ändern.

• Die Kameras mit Farbsensor haben bei schlechten Lichtverhältnissen eine

geringere Empﬁndlichkeit als Schwarz/Weiß-Kameras. In schlecht beleuchteter

Umgebung wird daher empfohlen, für eine zusätzliche Lichtquelle zu sorgen

• WICHTIG: Um die Funktionsweise des Gerätes nicht zu beeinträchtigen,

sicherstellen, dass die Metallfrontblende des Artikels 4893 nicht gegen andere

Metallteile reibt und dadurch die eigene Isolierung beschädigt.

Manual técnico del kit unifamiliar Arts. 8461 M y 8461MB

Manual técnico kit monofamiliar Art. 8461M, 8461MB

Operating distances

1209

4893

6700W

6701W

1209

4893

1214/2C

1216

1214/2C

6700W

6701W

6700W

6701W

The total number of internal units with the same user code and call repetition devices (additional ringtone Art. 1229A)

connected to these internal units cannot exceed 4 (with a maximum of 1 main internal unit and 3 secondary internal units).

Connect only one call repetition device for each internal unit.

A MAX B MAX

Comelit Art. 4577/4579 1 mm2 (Ø 1,2 mm AWG 17)

200 m

(655 feet)

100 m

(330 feet)

UTP5 cat. 5 0,2 mm2 (Ø 0,5 mm AWG 24)

100 m

(330 feet)

60 m

(195 feet)

0,28 mm2 (Ø 0,6 mm AWG 23)

100 m

(330 feet)

60 m

(195 feet)

0,5 mm2 (Ø 0,8 mm AWG 20)

100 m

(330 feet)

60 m

(195 feet)

1 mm2 (Ø 1,2 mm AWG 17)

100 m

(330 feet)

60 m

(195 feet)

1 mm2 (Ø 1,2 mm AWG 17)

80 m

(260 feet)

40 m

(130 feet)

1,5 mm2 (Ø 1,4 mm AWG 15)

100 m

(330 feet)

60 m

(195 feet)

*UTP5 cat. 5 0,2 mm2 (Ø 0,5 mm AWG 24)

MULTI PAIR CABLE

GREEN

ORANGE

BLU

GREEN / WHITE

ORANGE / WHITE

BLU / WHITE

BROWN / WHITE

BROWN

120 m

(390 feet)

70 m

(230 feet)

UTP cable with multi-cable connection: FOLLOW THE COLOURS SHOWN IN THE DIAGRAM!

Power supply unit Art. 1209

Description

31 Vdc power supply unit for 2-wire KIT, for direct connection to the external unit and internal unit.

Equipped with overload and short circuit protection.

Input voltage 110-240 VAC.

Dimensions: 108x90x62 mm (6 DIN modules).

50-60Hz

OUTPUT/SORTIE 31V 0.5A

1.2A 1'on/5'o

ta=40°C

110V-240V

800mA

INPUT/D'ENTREE

C US

Ar 1209

Dopo un cortocircuito,per ripristinare l'apparecchio,

interrompere l'alimentazione per circa 1 minuto.

To reset the operation after a short circuit,cut o mains

voltage for about 1 minute.

Apres un court circuit, pour remettre en fonction l'appareil,

interrompre l'alimentation pendant environs une minute.

257258

1 2 43

1. L N mains power input 110-240 V~

2. Terminal protection

3. L1 L1 main bus line input (31 V

)

4. L2 L2 riser bus line output (31 V

)

The electrical system of the building must be fitted with an (easily accessible) omnipolar mains switch with a

contact opening of at least 3 mm, which is capable of cutting off the power supply of the device.

External unit Art. 4893

Description

Wall-mounted external unit for Quadra series door entry monitor. Die-cast aluminium front panel, wide-angle colour camera

and single LED for lighting at night.

Capacitive buttons with the option of setting 1 to 4 call buttons via dip switch.

Indicator LED for call sent, lock-release activated, audio activated and system busy.

Loudspeaker volume adjustment and audio balancing. Bus line power supply.

External unit dimensions: 95x195x23 mm.

1. Die-cast aluminium cover

2. Camera lighting LED set by default to activate in response

to a call (can be disabled by setting DIP 7 to ON, see

page 10)

3. Wide-angle colour camera

4. Loudspeaker

5. Indicator LED

call sent

lock-release enabled

audio enabled

system engaged

6. Transparent front panel with label-holder in 1 / 2 / 4

button versions (default 1 button)

f To send the call, touch the button corresponding to

the user you want to contact

7. Microphone

JP1

8. Terminal block M1

LL bus line connection

RTE timed local lock-release input

COM common input for RTE and DO contacts

DO door open indication input

9. Terminal block M2

SE- SE+ connection for electric door lock

NC relay normally closed contact

NO relay normally open contact

C relay common contact

10. Loudspeaker volume control

11. Audio balance

12. JP1 enable RC network for door lock ﬁlter on relay

contacts (see page 40)

13. CNF programming conﬁrmation switch

14. PR programming input/output switch

15. DIP SWITCH for function programming

16. Microphone volume control

Installation

OPEN

163 cm

130 cm

CAUTION!

Tighten

properly to

avoid leaks

COM

L L

RTE

6 7

optional

You can download the free software (Art. 1235A) from the website www.comelitgroup.com to print the entrance panel name

tags, using the adhesive pre-cut sheets available in our catalogue (Art. 1217)

REMOVE

Replaceable nameplates

for 1 user for 2 users for 3 users

AVAILABLE NAMEPLATES

MAKE SURE THE

POSITIONING IS

CORRECT

BEFORE GLUEING

THE NAMES IN PLACE

JOHN SMITH

PETER WHIT

8 9

Labels must be made of non-conductive material so as not to compromise the operation of the soft-touch buttons

Before fixing the screw, make sure that you do not need to programme the external unit and make sure that the

metal front panel does not rub against other metal parts, with consequent risk of damage to its insulating coating

CAUTION!: To ensure that the product remains water-tight: make sure that the fixing procedure is carried out

correctly

10 11 12

Leakage

risk

MINIMUM 8

FULL

TURNS

13 14

DIP 1 DIP 2 DIP 3 DIP 4 DIP 5 DIP 6 DIP 7 DIP 8

The lock-

release relay

and the

second relay

are controlled

by 2 separate

buttons (e.g.

lock-release

button and

actuator

button)

lock-release

activation time:

8 sec.

relay activation

time: 8 sec.

reset wait time:

1 sec.

Call

transmission:

triple

confirmation

tones (call,

lock-release,

relay, audio

enabled):

disabled

Camera

lighting LED:

disabled

LED lighting

of nameholder

front panels:

OFF

The lock-

release relay

and the

second relay

are controlled

by a single

button (e.g.

lock-release

button)

OFF

lock-release

activation time:

2 sec.

OFF

relay activation

time: 2 sec.

OFF

reset wait time:

10 sec.

OFF

Call

transmission:

single

OFF

confirmation

tones (call,

lock-release,

relay, audio

enabled):

enabled

OFF

Camera

lighting LED:

enabled

OFF

LED lighting

of nameholder

front panels:

External unit settings

f Set the DIP-switches of S1 corresponding to the function that you want to programme as shown in the table below

Call address programming for 2-4 users and additional external unit

example:

3 4

√ Take note of the DIP-switch settings.

NOTE Fig. 3 - On the DIP-switch, set the code corresponding to the

function you want to program as shown in the table on page 11.

Reset the configuration of the DIP-switches of S1

Code Dip-Switch ON Function

1 1 button 1 enabled with call address 1 (default)

2 2 buttons 1-2 enabled with call addresses 1-2

4 3 buttons 1-2-3-4 enabled with call addresses 1-2-3-4

8 4 Porter with switching (secondary)

16 5 Secondary porter

32 6 Main porter

254 2,3,4,5,6,7,8 Restore default

Programming a generic call address

example:

3 4

√ Take note of the DIP-switch settings.

NOTE Fig. 3 - Set the user code on Dip Switches S1

(see table A on page 13).

Reset the configuration of the DIP-switches of S1

Riser addresses

TAB. A

Code

Dip switch

Code

Dip switch

Code

Dip switch

Code

Dip switch

Code

Dip switch

Code

Dip switch

Code

Dip switch

Code

Dip switch

1 1 31 1,2,3,4,5 61 1,3,4,5,6 91 1,2,4,5,7 121 1,4,5,6,7 151 1,2,3,5,8 181 1,3,5,6,8 211 1,2,5,7,8

2 2 32 6 62 2,3,4,5,6 92 3,4,5,7 122 2,4,5,6,7 152 4,5,8 182 2,3,5,6,8 212 3,5,7,8

3 1,2 33 1,6 63 1,2,3,4,5,6 93 1,3,4,5,7 123 1,2,4,5,6,7 153 1,4,5,8 183 1,2,3,5,6,8 213 1,3,5,7,8

4 3 34 2,6 64 7 94 2,3,4,5,7 124 3,4,5,6,7 154 2,4,5,8 184 4,5,6,8 214 2,3,5,7,8

5 1,3 35 1,2,6 65 1,7 95 1,2,3,4,5,7 125 1,3,4,5,6,7 155 1,2,4,5,8 185 1,4,5,6,8 215 1,2,3,5,7,8

6 2,3 36 3,6 66 2,7 96 6,7 126 2,3,4,5,6,7 156 3,4,5,8 186 2,4,5,6,8 216 4,5,7,8

7 1,2,3 37 1,3,6 67 1,2,7 97 1,6,7 127 1,2,3,4,5,6,7 157 1,3,4,5,8 187 1,2,4,5,6,8 217 1,4,5,7,8

8 4 38 2,3,6 68 3,7 98 2,6,7 128 8 158 2,3,4,5,8 188 3,4,5,6,8 218 2,4,5,7,8

9 1,4 39 1,2,3,6 69 1,3,7 99 1,2,6,7 129 1,8 159 1,2,3,4,5,8 189 1,3,4,5,6,8 219 1,2,4,5,7,8

10 2,4 40 4,6 70 2,3,7 100 3,6,7 130 2,8 160 6,8 190 2,3,4,5,6,8 220 3,4,5,7,8

11 1,2,4 41 1,4,6 71 1,2,3,7 101 1,3,6,7 131 1,2,8 161 1,6,8 191 1,2,3,4,5,6,8 221 1,3,4,5,7,8

12 3,4 42 2,4,6 72 4,7 102 2,3,6,7 132 3,8 162 2,6,8 192 7,8 222 2,3,4,5,7,8

13 1,3,4 43 1,2,4,6 73 1,4,7 103 1,2,3,6,7 133 1,3,8 163 1,2,6,8 193 1,7,8 223 1,2,3,4,5,7,8

14 2,3,4 44 3,4,6 74 2,4,7 104 4,6,7 134 2,3,8 164 3,6,8 194 2,7,8 224 6,7,8

15 1,2,3,4 45 1,3,4,6 75 1,2,4,7 105 1,4,6,7 135 1,2,3,8 165 1,3,6,8 195 1,2,7,8 225 1,6,7,8

16 5 46 2,3,4,6 76 3,4,7 106 2,4,6,7 136 4,8 166 2,3,6,8 196 3,7,8 226 2,6,7,8

17 1,5 47 1,2,3,4,6 77 1,3,4,7 107 1,2,4,6,7 137 1,4,8 167 1,2,3,6,8 197 1,3,7,8 227 1,2,6,7,8

18 2,5 48 5,6 78 2,3,4,7 108 3,4,6,7 138 2,4,8 168 4,6,8 198 2,3,7,8 228 3,6,7,8

19 1,2,5 49 1,5,6 79 1,2,3,4,7 109 1,3,4,6,7 139 1,2,4,8 169 1,4,6,8 199 1,2,3,7,8 229 1,3,6,7,8

20 3,5 50 2,5,6 80 5,7 110 2,3,4,6,7 140 3,4,8 170 2,4,6,8 200 4,7,8 230 2,3,6,7,8

21 1,3,5 51 1,2,5,6 81 1,5,7 111 1,2,3,4,6,7 141 1,3,4,8 171 1,2,4,6,8 201 1,4,7,8 231 1,2,3,6,7,8

22 2,3,5 52 3,5,6 82 2,5,7 112 5,67 142 2,3,4,8 172 3,4,6,8 202 2,4,7,8 232 4,6,7,8

23 1,2,3,5 53 1,3,5,6 83 1,2,5,7 113 1,5,6,7 143 1,2,3,4,8 173 1,3,4,6,8 203 1,2,4,7,8 233 1,4,6,7,8

24 4,5 54 2,3,5,6 84 3,5,7 114

2,5,6,7 144 5,8 174 2,3,4,6,8 204 3,4,7,8 234 2,4,6,7,8

25 1,4,5 55 1,2,3,5,6 85 1,3,5,7 115 1,2,5,6,7 145 1,5,8 175 1,2,3,4,6,8 205 1,3,4,7,8 235 1,2,4,6,7,8

26 2,4,5 56 4,5,6 86 2,3,5,7 116 3,5,6,7 146 2,5,8 176 5,6,8 206 2,3,4,7,8 236 3,4,6,7,8

27 1,2,4,5 57 1,4,5,6 87 1,2,3,5,7 117 1,3,5,6,7 147 1,2,5,8 177 1,5,6,8 207 1,2,3,4,7,8 237 1,3,4,6,7,8

28 3,4,5 58 2,4,5,6 88 4,5,7 118 2,3,5,6,7 148 3,5,8 178 2,5,6,8 208 5,7,8 238 2,3,4,6,7,8

29 1,3,4,5 59 1,2,4,5,6 89 1,4,5,7 119 1,2,3,5,6,7 149 1,3,5,8 179 1,2,5,6,8 209 1,5,7,8 239 1,2,3,4,6,7,8

30 2,3,4,5 60 3,4,5,6 90 2,4,5,7 120 4,5,6,7 150 2,3,5,8 180 3,5,6,8 210 2,5,7,8 240 5,6,7,8

Description of Monitor Art. 6700W and Art. 6701W

L CFP1

CFP2

1. Brightness control

f To increase the value, turn clockwise

2. Colour intensity adjustment for Art. 6701W

Contrast adjustment for B/W monitor Art. 6700W

f To increase the value, turn clockwise

3. 4.3’’ LCD screen (in colour for Art. 6701W, B/W for Art. 6700W)

4. Call volume adjustment (high - medium - low)

5. Soft-touch keys

6. Monitor handset (lift handset to start communication)

7. S1 User code programming microswitches (see table on page. 13)

8. S2 Button and function programming microswitches (marked with a red corner)

DIP 1-2-3-4 for button function programming

DIP 5-6 access to programming

DIP 7 for power supply voltage management (see diagrams and variants on page 29), default = ON

DIP 8:

ON secondary monitor

OFF main monitor (default)

9. Loudspeaker volume adjustment (for setting intercom audio only)

10. CV5 Video closing jumper

11. Pin for securing terminal block

12. Space for housing the operation accessory for keys

(standard on all black monitors, available to purchase

separately for white monitors Art. 6733W)

Terminal block for system connection

LL Bus line connection terminals

CFP1 CFP2 Floor door call input

A maximum of 1 main monitor can be set

Soft-touch keys description

Indicator LED description

f Press the desired key once to activate the function associated with it

Lock-release LED

slow flashing: door open;

1 flash after pressing: door opening conﬁrmation;

continuous flashing: call in progress.

Privacy LED (red)

steady: privacy function enabled

3 flashes (every 5 sec.): doctor function enabled

continuous flashing: device in programming mode

4 flashes: system engaged

Lock-release key

Key 1 Actuator function (programmable)

Key 2 Self-ignition function (programmable)

Privacy key

Keys (programmable) present as standard on all black monitors (for white monitors the KIT with additional buttons Art.

6733W is available to purchase separately)

Wait for approximately 1 sec. before pressing the same key again. Pressing the same key several times in quick

succession will cancel the command.

Installation

optional

fixing

16,0 cm

17,5 cm

1C1B1A

6 7

CLACK!

Removing / Fitting the terminal

L L

(to remove)

CLACK!

8 97

L CFP1

CFP2

Fitting upgrade KIT Art. 6733W

Standard conﬁguration for DIP switches 1-2-3-4

Monitor conﬁguration

Standard conﬁguration for soft-touch keys

DIP S2 Art. (6700W / 6700W/BM / 6701W / 6701W/BM ) + Art. 6733W

DIP 1 DIP 2 DIP 3 DIP 4 P1 P2

P3 P4 P5 P6

0 0 0 0 ACT AI

NULL D NULL K

1 0 0 0 NULL AI INT INTb D ACT

0 1 0 0 INT AI INTb ACT NULL NULL

1 1 0 0 ACT NULL NULL NULL K D

0 0 1 0 ACT ACT ACT ACT ACT ACT ACT

1 0 1 0 INT ACT

NULL NULL INTb NULL

0 1 1 0 AI D K NULL NULL INTb

1 1 1 0 INTb INT AI INT NULL D

0 0 0 1 NULL NULL D AI INT INTb

1 0 0 1 K NULL NULL NULL AI INT

0 1 0 1 NULL K NULL ACT INT AI

1 1 0 1 NULL NULL NULL K ACT D

0 0 1 1 INTb AI INT ACT D NULL

1 0 1 1 INT INT INT INT INT INT

0 1 1 1 NULL NULL NULL NULL NULL NULL NULL

1 1 1 1 PROG

Legend

Lock- release

ACT Actuator

AI Self-ignition

K Guardian door-entry phone call

D Doctor

INT General or selective programmable intercom - singlefamily call standard for KIT 8461

INTb General or selective programmable intercom - two-family call standard for KIT 8461

NULL No function or DO NOT use

PROG

Programmed functions, see pages 19-23.

In this Dip switch setting, the buttons control the programmed functions; the NON-programmed buttons

control functions referred to on line 0000 (default).

If the default settings (see table on page 18) do not reﬂect requirements, the keys can be programmed dierently by carrying

out the steps below.

At the end, set S2 DIP switches 1-2-3-4 to the combination 1111 (PROG setting in the configuration tables on pages

19-23). In this dip switch setting, the keys control the programmed functions; the NON-programmed keys control

functions referred to on line 0000 (see table on page 18). Restore the user code setting on S1, see table A on page 13.

Warning

Programming/deleting intercom address

Selective intercom addresses

You must set the intercom address on all the riser’s internal units.

You can assign the same intercom address to a maximum of 3 internal units.

For group calls, select the desired intercom codes simultaneously (max. 3).

Advanced monitor conﬁguration

Programming for intercom call

General intercom: function allowing calls to one or more internal units identified by the same call address as used

by the external unit.

Selective intercom: function allowing calls to one or more internal units identified by a dedicated call address (see

table B, page 19) which is different from the one used by the external unit.

General and selective intercoms CANNOT be used together on the same riser.

Take note of the S2, S1 setting and restore it when programming is complete

1) 2) 3)

Programming; set code,

TAB. B on page 19

S2 DIP

1 2 3 4 5 6

0 0 0 1 1 1

Cancellation

DIP OFF

DIP ON

S2 DIP

1 2 3 4 5 6

1 1 1 1 1 1

TAB. B

Code Dip switch ON S1 Code Dip switch ON S1

1 1

5 5

2 2 6 6

3 3 7 7

4 4 8 8

DIP S2

Art. (6700W / 6700W/BM / 6701W / 6701W/BM ) +

Art. 6733W

DIP S1

DIP 1 DIP 2 DIP 3 DIP 4 P1 P2

P3 P4 P5 P6

ADDRESS

0 0 0 0

1 0 0 0 INT INTb

0 1 0 0 INT INTb

1 1 0 0

0 0 1 0

1 0 1 0 INT

INTb

0 1 1 0 INTb

1 1 1 0 INTb INT INT

0 0 0 1 INT INTb

1 0 0 1 INT

0 1 0 1 INT

1 1 0 1

0 0 1 1 INTb INT

1 0 1 1 INT INT INT INT INT INT

0 1 1 1

1 1 1 1 PROG

Example 1 - General intercom

on a monitor with user code 5, P3 programming = general internal call, P4 = general intercom with address 9

Example 2 - Selective intercom

on a monitor with user code 1 and intercom address 1, P3 programming = selective intercom with address 2, P4 = selective

intercom with address 3

1. Set S2 DIP switch 6 to the combination 01.

» the privacy LED ﬂashes.

S2 DIP

1 2 3 4 5 6

0 0 0 0 0 1

2. Refer to the table on page 20 and select a combination in which the intercom function (either INT or INTb) is listed for the

keys you wish to program.

E.g. 1: for P3= general internal call, set S2 DIP switches 1-2-3-4 to the combination 1000 or 0011 or 1011 (P3=INT), set S1

with address 5 in accordance with table A on page 13, go to point 3.

E.g. 1: for P4= general intercom, set S2 DIP switches 1-2-3-4 to the combination 1110 or 1011 (P4=INT), set S1 with

address 9 in accordance with table A on page 13, go to point 3.

E.g. 2: for P3= single-family intercom, set S2 DIP switches 1-2-3-4 to the combination 1000 or 0011 or 1011 (P3=INT), set

S1 with address 2 in accordance with table B on page 19, go to point 3.

E.g. 2: for P4= selective intercom, set S2 DIP switches 1-2-3-4 to the combination 1110 or 1011 (P4=INT), set S1 with

address 3 in accordance with table B on page 19, go to point 3.

3. Press and release the key to be associated with the function

» the lock-release LED lights up.

» a conﬁrmation tone will sound.

4. To exit programming mode, set S2 DIP switches 5-6 to the combination 00

f the privacy LED switches o

5. When programming is complete, set S2 DIP switches 1-2-3-4 to the combination 1111. Restore the user code

setting on S1, see table A on page 13.

Programming buttons for intercom call

Page is loading ...

Comelit 8461MB Owner's manual

Brand: Comelit

Model: 8461MB

Type: Owner's manual

This manual is also suitable for

8461M

Download PDF

report

in other languages

italiano: Comelit 8461MB Manuale del proprietario

Comelit 8461MB Owner's manual

This manual is also suitable for

Comelit 8461MB Owner's manual

in other languages

Related papers

Other documents