Alfi Fire Hot Tub Installation guide

Alfi
Brand
Alfi
Model
Fire Hot Tub
Type
Installation guide
ALFIbrand.com
Al Brand All Rights Reserved
Installation Manual
1
1
2
3
4
5
6
7
8
9
10
1
2222
3
4
5
6
7
8
9
1
0
1
1
3
1
1
1
2
8
1
1
Parts Identification
NO
material name
Figure
QTY
NO
material name
Figure
QTY
Outdoor bathtub
The bathtub cover
bar clasp
The heating coil
Seal ring
Outlet pipe
Stainless steel screw
fire basket
Ash plate
wind screen
tool
hexangon wrench
NO PART NAME SKU QTY FIGURE NO PART NAME SKU QTY FIGURE
1 Fire Hot Tub
Fire Hot Tub
1 6 Plastic Pipe
R-FIRE_
PlasticPipe
1
2 Tub Cover
R-FIRE_Cover
1 7 Rubber Ring
R-FIRE_
RubberRing
2
3 Bar Clip
R-FIRE_Clip
3 8 SS Screw
R-FIRE_Screw
8
4 Wind Screen
R-FIRE_Wind-
Screen
1 9 Fire Basket
R-FIRE_Basket
1
5 Heating Coil
R-FIRE_Coil
1 10 Ash Tray
R-FIRE_Ashtray
1
Tool Hex Key
2
Installation of Cover
Installation of Coil
Seal Rubber Ring
Wind Screen & Basket Assembly
Hang fire basket inside coil, then place Ash Tray underneath. Attach Wind
Screen as seen in the image above.
3
Drainage After Use
To drain tub after use, attach plastic pipe to drain and ensure
water drains onto ground or lawn.
4
Attention!
Hot!
Safety & Use
To maximize fun and safety during use of the FireHotTub,
please follow our installation guidelines and ensure that all
safety measures are met.
1. Environment
-Decide in advance where you would like to place your
new tub. Remember that the area must be clear of brush
and debris, on a at solid surface, in the open air (not
underneath a shelter or roof) and ONLY outdoors.
-Consider recycling the water by draining directly into your
garden or on your lawn. (You can connect your garden
hose to the tub.)
3. Fire & Water Temperature
-The FireHotTub burns real wood. Consider the dangers of
an open ame around plants, pets, and children.
-Water temperature should not exceed 100 degrees
Fahreneit (38 degrees Celsius). Given that the tub does not
have a thermal indicator, it is up to you to ensure water
safety before entering the tub. Please wait for water to cool
before draining.
-Drain the FireHotTub after each use in order to prevent
growth of dangerous bacteria.
-To avoid damage to the heating coil, ensure that the
tub is lled with water before igniting a re inside the coils.
Extinguish the re completely before draining the tub.
2. Installation & More
-DO NOT attempt to move the FireHotTub while it is lled
with water.
-Observe the direction of the wind and ensure that heating
coil is installed away from wind.
-Tub should be placed on a solid surface with a minimum
total load-bearing capacity of 2810lbs (1275kg).
-Hot water may spill from the rims when multiple people are
in the tub. Ensure that the surface the tub is on will not melt
if water spills.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Alfi Fire Hot Tub Installation guide

Alfi
Brand
Alfi
Model
Fire Hot Tub
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents