Sears 010 User manual

dFgO 3T_EmbroiderylSewing Mach ine

Owner's Manual

Model 385,19010200

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com

851-81%004 Sears Canada Inc., Toronto, Ont., i5S 288 www.sears.ca

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be followed, including the followings:

Read all instructions before using this appliance.

DANGER- To reduce the risk of electric shock:

1. An appliance should never be left unattended when plugged in. Always unplug this sewing machine from the

electric outlet immediately after using and before cleaning.

2. Always unplug before replacing a sewing machine bulb. Replace bulb with same type rated 13.2 V, 3 Watts.

WARN ING- To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children.

2. Use this appliance only for its intended use as described in this owner's manual.

Use only attachments recommended by the manufacturer as contained in this owner's manual.

3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped

or damaged, or dropped into water.

Return this sewing machine to the nearest Sears store or service center for examination, repair, electrical or

mechanical adjustment.

4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this sewing machine and foot

controller free from accumulation of lint, dust and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8. To disconnect, turn all controls to the off ("O") position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10. Keep fingers away from all moving parts. Special care is required around the sewing machine needle.

11.Always use the proper needle plate. The wrong plate can cause the needle to break.

12. Do not use bent needles.

13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

14. Switch this sewing machine off ("O") when making any adjustment in the needle area, such as threading the needle,

changing the needle, threading the bobbin or changing the presser foot, and the like.

15.Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or when making any

other adjustments mentioned in this owner's manual.

16. Hold plug when rewinding into cord reel. Do not allow plug to whip when rewinding.

SAVE THESE INSTRUCTIONS

I

Before using your sewing machine for the first time, place a waste fabric under the presser foot

and run the machine with thread for a few minutes. Wipe away any oil which may appear.

PROTECTION AGREEMENTS

In the U.S.A.

Master Protection Agreements

Congratulations on making a smart purchase. Your new

Kenmore ®appliance is designed and manufactured for

years of dependable operation. But like all products, it may

require preventive maintenance or repair from time to time.

That's when having a Master Protection Agreement can

save you money and aggravation.

Purchase a Master Protection Agreement now and protect

yourself from unexpected hassle and expense.

The Master Protection Agreement also helps extend the

life of your new appliance. Here's what's included in the

Agreement:

[] Expert service by our 12,000 professional repair

specialists

[] Unlimited service and no charge for parts and labor

on all covered repairs

[] "No-lemon" guarantee - replacement of your covered

product if more than three product failures occur within

twelve months

[] Product replacement if your covered product can't be

fixed

[] Annual Preventive Maintenance Check at your request

- no extra charge

[] Fast help by phone - non-technical and instructional

assistance on products repaired in your home, plus

convenient repair scheduling

[] Power surge protection against electrical damage due

to power fluctuations

[] Rental reimbursement if repair of your covered product

takes longer than promised

In Canada

Maintenance Agreements

Your purchase has added value because you can depend

on Sears HomeCentral ®for service. With over 2400

Service Technicians and access to over 900,000 parts and

accessories, we have the tools, parts, knowledge and skills

to ensure our pledge: We Service What We Sell.

Your Kenmore ®appliance is designed, manufactured and

tested to provide years of dependable operation. Yet any

major appliance may require service from time to time. The

Sears Maintenance Agreement offers you an outstanding

service program, affordabiy priced.

The Sears Maintenance Agreement

• Is your way to buy tomorrow's service at today's price.

• Eliminates repair bills resulting from normal wear and

tear.

• Provides for non-technical and instructional assistance.

• Even if you don't need repairs, provides an annual

Preventive Maintenance Check, at your request, to

ensure that your appliance is in proper running condition.

Some limitations apply. For information concerning

Sears Canada Maintenance Agreements, call

1-800-361-6665.

Once you purchase the Agreement, a simple phone call is

all that it takes for you to schedule service. You can call

anytime day or night, or schedule a service appointment

online.

Sears has over 12,000 professional repair specialists, who

have access to over 4.5 million quality parts and

accessories. That's the kind of professionalism you can

count on to help prolong the life of your new purchase for

years to come. Purchase your Master Protection

Agreement today!

Some limitations and exclusions apply.

For prices and additional information, call

1-800-827-6655.

Sears Installation Service

For Sears guaranteed professional installation of home

appliances and items like garage door openers and water

heaters, in the U.S.A. call 1-800-4-MY-HOME ®

S

Machine Specifications

Item

Sewing speed (Maximum):

Stitch length:

Stitch width:

Stitch package (Stitch functions):

(Built-in stitches):

Buttonhole:

Machine dimensions:

Weight (Net):

Specification

Over 820 s.p.m.

5 mm (Maximum)

7 mm (Maximum)

1160

Conventional 673 built-in stitches with 447 built-in embroidery

design

1 step built-in buttonhole

W 18.9" (481.1 mm) x D 9.2" (234.5 mm) x H 12.8" (326.2 mm)

23.9 Ibs (1 lkg)

Kenmore Sewing Machine Warranty

Full 25 Year Warranty on Internal Mechanical Components

For 25 years from the date of purchase, Sears willprovide free repair for the internal mechanical components of

this sewing machine if they are defective in material orworkmanship.

Full TwoYearWarranty on Electrical Equipment

For two years from the date of purchase, Sears will provide free repair for the electrical equipment of this sewing

machine, if any part of it, including motor, wiring, electronic circuitry,switch and speed control, is defective in

material or workmanship. This two-year warranty does not include light bulbs, which are expendable parts only

included in the 90 day warranty described below.

Full 90 Day Warranty on All Parts and Mechanical Adjustments

For 90 days from the date of purchase, Sears wilt provide free parts replacement and mechanical service

necessary for the proper operation of this sewing machine, except for normal maintenance as described in the

owner's manual.

Warranty service is available by returning this sewing machine to the nearest Sears Service Center in

the United States. If this sewing machine is used for commercial or rental purposes, warranty service is

available for only 90 days from the date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D/817WA, Hoffman Estates, IL 60179

Kenmore Sewing Machine Warranty

Full 25 Year Warranty on Internal Mechanical Components

For 25 years from the date of purchase, Sears willprovide free repair for the internal mechanical components of

this sewing machine if they are defective in material orworkmanship.

Full TwoYearWarranty on Electrical Equipment

For two years from the date of purchase, Sears will provide free repair for the electrical equipment of this sewing

machine, if any part of it, including motor, wiring, electronic circuitry,switch and speed control, is defective in

material or workmanship. This two-year warranty does not include light bulbs, which are expendable parts only

included in the 90 day warranty described below.

Full 90 Day Warranty on All Parts and Mechanical Adjustments

For 90 days from the date of purchase, Sears wilt provide free parts replacement and mechanical service

necessary for the proper operation of this sewing machine, except for normal maintenance as described in the

owner's manual.

Warranty service is available by returning this sewing machine to the nearest Sears Service Center in

Canada. If this sewing machine is used for commercial or rental purposes, warranty service is available for only 90

days from the date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from province to

province.

Sears Canada,Toronto, Ont., M5B 2B8

Ill

TABLE OF CONTENTS

SECTION I. NAME OF PARTS

Names of Parts ............................................................... 2

Available Accessories and Attachments ......................... 3

SECTION I1. GETTING READYTO SEW

Connecting Machine to Power Supply ............................ 4

Before Using Your Sewing Machine ................................ 4

For Your Safety ................................................................ 4

Polarized Plug ................................................................. 4

Machine Operating Buttons............................................. 5

Start/stop Button ............................................................. 5

Reverse Button................................................................ 5

• Patterns 1,2, 6 and 7: ................................................ 5

• All other patterns: ....................................................... 5

Auto-lock Button .............................................................. 5

• Patterns 1,2, 6 and 7: ................................................ 5

• All the other patterns: ................................................. 5

Up/down Needle Button .................................................. 5

Speed Control Lever ....................................................... 5

Foot Control .................................................................... 6

Operation Instructions: ................................................. 6

Pressure Dial ................................................................... 6

To Drop or Raise the Feed Dogs ..................................... 6

Extension Table ............................................................... 7

• Detaching the Table .................................................... 7

• Attaching the Table ..................................................... 7

Presser Foot Lifter ........................................................... 7

Thread Cutter .................................................................. 8

Changing Needle ............................................................ 8

Changing Presser Foot ................................................... 8

• To remove ................................................................... 8

• To attach ..................................................................... 8

Correcting Distorted Stitch Patterns ................................ 9

Presser Foot Types ....................................................... 10

• Zigzag foot (Foot A) .................................................. 10

• Straight stitch foot (Foot H) ....................................... 10

• Automatic buttonhole foot (Foot R) ........................... 10

• Zipper foot (Foot E) .................................................. 10

• Overedge foot (Foot C) ............................................. 10

• Satin stitch foot (Foot F) ........................................... 10

• Blind hem stitch foot (Foot G) ................................... 10

• 1/4"Seam foot (Foot O) ............................................ 11

• Embroidery foot (Foot P) .......................................... 11

• Walking foot .............................................................. 11

Selecting Needle and Fabric ......................................... 12

Bobbin Winding ............................................................. 13

• Removing the hook cover plate ................................ 13

• Horizontal spool pin .................................................. 13

• Additional spool pin .................................................. 13

Bobbin Winding ....................................................... 14-15

• Inserting the bobbin .................................................. 15

Threading the Machine ........................................... 16-17

• Threading the machine ............................................. 16

• Built-in needle threader ............................................ 16

• Drawing up bobbin thread ........................................ 17

SECTION III. CONVENTIONAL SEWING

Visual Touch Screen ...................................................... 18

Mode Selection Keys ..................................................... 18

Pattern Selection ........................................................... 19

Utility Stitches ................................................................ 19

Machine Settings ........................................................... 20

Common Set Mode ....................................................... 20

Embroidery Set Mode ................................................... 21

Flag Mode-Language Selection .................................... 21

Straight Stitch .......................................................... 22-23

•To sew ...................................................................... 22

•Securing seam ......................................................... 22

•Changing sewing direction ....................................... 22

• Needle plate guide line ............................................. 23

•To sew from the edge of thick fabric ......................... 23

Quilting .......................................................................... 23

Quilting with Walking Foot ............................................. 24

•To attach the walking foot ......................................... 24

Manual Adjustment of Straight Stitches .................. 24-25

•Changing needle drop position ................................. 25

•Changing stitch length .............................................. 25

Adjust the Needle Thread Tension for Straight Stitch .... 26

•Correct tension ......................................................... 26

•Tension is too tight .................................................... 26

•Tension is too loose .................................................. 26

Variety of Straight Stitches ...................................... 27-28

Lock-a-matic Stitch ........................................................ 27

Locking Stitch ................................................................ 27

Triple Stretch Stitch ....................................................... 27

Stretch Stitch ................................................................. 28

Basting Stitch ................................................................ 28

Zipper Sewing ............................................................... 28

•To snap on the zipper foot ........................................ 28

• Fabric preparation ..................................................... 29

•To sew ...................................................................... 29

Zigzag Stitch ................................................................. 30

Manual Adjustment of Zigzag Stitch Width and Length 30

•Changing stitch width ............................................... 31

•Changing stitch length .............................................. 31

Adjust the Needle Thread Tension for Zigzag Stitch ..... 32

•Correct tension ......................................................... 32

•Tension is too tight .................................................... 32

•Tension is too loose .................................................. 32

Variety of Overcasting Stitches ..................................... 33

Overedge Stitch ............................................................ 33

Overedge Stitch (using zigzag stitch) ............................ 33

Multiple Zigzag Stitch .................................................... 33

•Seam finishing .......................................................... 33

• Mending .................................................................... 33

Serging .......................................................................... 34

Double Overedge Stitch ................................................ 34

Blind Hem Stitch ............................................................ 35

•To sew ...................................................................... 35

Shell Tuck ...................................................................... 35

SECTION IV. BUTTONHOLE

Various kinds of buttonholes and their uses .................. 36

Square BH ..................................................................... 37

• Preparation for sewing .............................................. 37

•To sew ................................................................ 37-38

IV

TABLE OF CONTENTS

• To repeat buttonhole sewing ..................................... 38

• Changing buttonhole width ....................................... 39

• Changing buttonhole stitch density ........................... 39

Corded Buttonhole ........................................................ 40

• To sew ...................................................................... 40

Darning ......................................................................... 41

• To sew ...................................................................... 41

• To sew a shorter darning .......................................... 41

• To sew the same size darning .................................. 41

• To adjust the evenness of darning ............................ 41

Tacking .......................................................................... 42

• To sew a shorter tack ................................................ 42

• To sew the same size tack ........................................ 42

Eyelet ............................................................................ 43

• To sew ...................................................................... 43

• To adjust the size of an eyelet .................................. 43

SECTION V. SATIN, DECORATIVE STITCHES AND

MONOGRAMMING

Key Functions .......................................................... 44-45

One Cycle Pattern Sewing

Example: pattern 28, L.S ............................................... 46

• To sew ...................................................................... 46

Elongation Sewing

Example: pattern 28 ...................................................... 46

• To sew ...................................................................... 46

Programming Pattern Combination

Example: pattern 28 and 31 .......................................... 47

• To sew ...................................................................... 47

Programming Pattern Combination with Mirror Image

Example: pattern 30 ...................................................... 47

• To sew ...................................................................... 47

Programming French Knot

Example: pattern 51, 39, 40 .......................................... 48

• To sew ...................................................................... 48

Combination of Satin Stitch and Decorative Stitch

Example: pattern 28, 70 ................................................ 48

• To sew ...................................................................... 48

To Sew from the Beginning of a Combination Pattern with

Beginning Key

Example: pattern 30 ...................................................... 49

• To sew ...................................................................... 49

Twin Needle Sewing ...................................................... 49

• To sew ...................................................................... 49

Individual Pattern Adjustment

Example:patterns 28, 30 and 32 ................................... 50

Editing Programmed Patterns ....................................... 50

• Example:

To delete pattern 30 from the combination with patterns

28, 30 and 32 ............................................................ 50

• Example:

To insert pattern 38 between pattern 28 and 30 in the.

combination of patterns 28, 30 and 32 ..................... 50

Program Check ............................................................. 51

• Example:

To check the patterns when patterns 64, 70, 30, 26,

31 and 38 ................................................................. 51

Saving and Opening a File ............................................ 52

• Saving a file .............................................................. 52

•Assigning a file name ............................................... 52

Opening a Saved File .................................................... 53

Deleting a Saved File .................................................... 53

MONOGRAMMING ................................................. 54-55

Programming a Monogram

Example: Programming in Block Type ........................... 55

Editing a Monogram ...................................................... 55

Deleting a Letter ............................................................ 55

Inserting a Letter (Character) ........................................ 55

SECTION VI. EMBROIDERY

Getting Ready to Sew Embroidery ................................ 56

• Embroidery Hoop F .................................................. 56

• Instruction for Template ............................................ 56

Stabilizer ....................................................................... 57

Types of Stabilizer ......................................................... 57

•Tear-away Stabilizer ................................................. 57

• Iron-on Stabilizer ...................................................... 57

• Cut-away Stabilizer ................................................... 57

•Water Soluble Stabilizer ........................................... 57

• Sticky Stabilizer ........................................................ 57

Usage: ........................................................................... 57

Adhesive (iron-on) Stabilizer ......................................... 57

To Attach the Stabilizer ................................................. 58

To Set the Fabric in the Embroidery Hoop .................... 58

To Attach the Embroidery Hoop to the Machine ........... 59

To Attach Embroidery Foot P ........................................ 59

Thread Holder ............................................................... 59

Built-in Embroidery Designs .......................................... 60

Pattern Selection Window ............................................. 60

Embroidery Mode Set ................................................... 61

Embroidery Screen ................................................. 62-63

Starting to Sew Embroidery .......................................... 64

Sewing Results ............................................................. 64

Monogram Embroidery ................................................. 65

Monogram Selection Screen ................................... 65-66

2-tetter Monogram ......................................................... 67

Example: 2-Letters with a crest ..................................... 67

Example: 2-Letters without a crest ................................ 67

• Making Corrections ................................................... 67

ATA PC Card ................................................................. 68

•To insert the ATA PC card ......................................... 68

•To eject the ATA PC card .......................................... 68

Selecting the Card Designs ........................................... 68

Reader/writer 19000 ..................................................... 69

• Connecting Reader/writer 19000 ............................. 69

Pattern Selection Screen .............................................. 69

Edit Mode ...................................................................... 70

Pattern Selection Windows in the Edit Mode ................ 70

Selecting the Pattern on the Edit Screen ...................... 70

Moving the Selected Design ......................................... 70

Cancel Key .................................................................... 71

Resizing the Selected Pattern ....................................... 71

Flipping the Selected Pattern ........................................ 71

Rotating the Selected Pattern ....................................... 71

Delete Key ..................................................................... 72

Changing the Fabric and Thread Colors ....................... 72

V

TABLE OF CONTENTS

• Fabric color change .................................................. 72

• Thread color change ................................................. 73

Pattern Combination (example 1) ................................. 74

Sewing Results ............................................................. 74

Pattern Combination (example 2) ................................. 75

Sewing Results ............................................................. 76

SECTION VII. NORMAL MAINTENANCE

Replacing the Light Bulbs ............................................. 78

• To replace the light bulb behind the face cover ........ 78

• To replace the light bulb on the underside of the

sewing arm ............................................................... 78

Cleaning the Hook Area ................................................ 79

Assemble the Hook Race .............................................. 79

STITCH/DESIGN CHART ....................................... 80-81

Conventional Sewing ..................................................... 80

Monogram ..................................................................... 80

Built-in Embroidery Designs .......................................... 81

Built-in Embroidery Monogram ..................................... 81

Troubleshootin ....................................................... 82-83

VI

SECTION I. NAME OF PARTS s

Names of Parts

Flip-top quick reference chart

Bobbin winder spindle

Bobbin thread cutter

Spool holder (Large)

Spool pin

Upper thread guide

Pressure dial

Thread take-up lever

Thread tension dial

Face cover

@ Thread cutter/holder

Built-in needle threader

Needle plate

Hook cover plate

Hook cover plate release button

Extension table

@ Feed balancing dial

@ Start/stop button

@ Reverse button

Auto-lock button

@ Up/down needle button

@ Speed control lever

@ Visual touch screen

@ Presser foot lifter

Carrying handle

Hand wheel

@ PC card slot

@ ATA PC Card (optional)

Card eject button

RS-232C port

@ Power supply plug (cord reel)

@ Machine socket

@ Power switch

@ Carriage (for embroidery)

Drop feed dog lever

Buttonhole lever

@ Thumb screw

@ Foot holder

@ Presser foot

Needle

@ Needle clamp screw

®

J

Available Accessories and Attachments

To order parts and accessories listed below, call:

1-800-366-PART (1-800-366-7278)

6 am - 11 pm, CST, 7 days a week

When ordering parts and accessories, provide the following

information:

1. Part Number

2. Part Name

3. Model Number of Machine

Ref. No.

39

Pad No.

*102869107

102403109

850807101

*993010900

*993001100

*993011100

*993011400

*993011600

*993011800

826815000

823801015

832523007

822804118

829801002

822801001

820817015

200008004

830810031

830823118

214508002

214015007

802422002

000009907

560406104

822814007

820832005

*741814003

802424004

625031500

822020514

822019509

829803004

851801104

851801403

*200002008

*200003009

*200005001

*200013105

*941620000

043271155

*851401007

851813006

851821007

851816009

851820006

Description

10 x Bobbin

Spool pin felt

Assorted needle set

5 x No. 9 needle (BROWN)

5 x No.11 stretch fabric needle (BLUE)

5 x No.11 needle (ORANGE)

5 x No.14 needle (RED)

5 x No.16 needle (PURPLE)

5 x No.18 needle (GREEN)

Twin needle

H:Straight stitch foot

A:Zigzag foot

F: Satin stitch foot

E:Zipper foot

C:Overedge foot

G:Blind hem foot

O:1/4" seam foot

P:Embroidery foot

R:Automatic buttonhole foot

Walking foot

Quilter bar (for walking foot)

Quilter

Light bulb

Seam ripper/Buttonhole opener

Scissors

Large screwdriver

Oil

Lint brush

Additional spool pin

Large spool holder

Small spool holder

Spool stand

P:Embroidery hoop

Template

Piping foot

Gathering foot

Pin-tuck foot

Hemmer foot (2mm)

Ruffler

Foot control

Clothsetter

Dust cover

Starter kit

Video

Template sheet

* These items are not furnished with the machine, but may be

ordered per instructions above.

S

"1 2

8

3 4 5 6

10 11 12

13 14 15 16 18

19

25

*29

34

39

17

20 '21 22 23 24

26 27 28

*30 "31 *32

*35 36 37 38

J

SECTION II. GETTING READY TO SEW

Connecting Machine to Power Supply

(_ Power supply plug

Power switch

Outlet

Red marker

(_ Foot control

(_ Foot control plug

Machine socket

1. Turn off the power switch @. Insert the foot control plug

into the machine socket (_.

2. Insert the power supply plug _ into the outlet _.

3. Turn the power switch @ to turn on the power and

sewing lights.

Notes:

• Do not pull the cords beyond the red marker _ on the

cords.

• If you turn off the power switch, wait 5 seconds before

turing it on again.

• Hold plug when rewinding into cord reel. Do not allow

plug to whip when rewinding.

Before UsingYour Sewing Machine

Before using your sewing machine for the first time, place a

waste fabric under the presser foot and run the machine

with thread for a few minutes. Wipe away any oil which may

appear.

ForYour Safety

* While in operation, always keep your eyes on the sewing

area. Do not touch any moving parts such as the thread

take-up lever, handwheel or needle.

* Always turn offthe power switch and unplug from the

power supply:

• When leaving the machine unattended.

• When attaching or removing any parts.

• When cleaning the machine.

* Do not place anything on the foot control, when not

sewing.

Polarized Plug

This appliance has a polarized plug (one blade wider than

the other). To reduce the risk of electric shock, this plug is

intended to fit in a polarized outlet only one way. If the plug

does not fit in the outlet, reverse the plug. If itstill does not

fit, contact a qualified electrician to install the proper outlet.

Do not modify the plug in any way.

S

\

J

Machine Operating Buttons

Start/stop Button

Start/stop button

Press the button to start or stop the machine. This button

can be used either in conventional sewing mode or Embroi-

dery mode. In conventional sewing mode, the machine

starts running slowly for the first few stitches; it then runs at

the speed set by the speed control lever.

Note:

The Start/stop button cannot be used when the foot

control is connected to the machine.

Reverse Button

Reverse button ii i _ ._. -..

• Patterns 1, 2,6and7: _i,j ' ::; :_:

The machine will sew =nreverse while the reverse button

is pressed.

• All other patterns:

When the reverse button is pressed, the machine will sew

locking stitches immediately and automatically stop.

Auto-lock Button

Auto-lock button

• Patterns 1, 2, 6 and 7:

When the auto-lock button is pressed, the machine will

immediately sew locking stitches and automatically stop.

• All other patterns:

When the auto-lock button is pressed, the machine will

sew locking stitches at the end of the current pattern and

automatically stop.

Up/down Needle Button

Up/down needle button

Press this button to bring the needle up or down.

Speed Control Lever

Sewing speed can be varied by the speed control lever

according to your sewing needs.

To increase sewing speed, slide the lever to the right.

To decrease sewing speed, slide the lever tothe left.

S

@

®

J

,,,.,,maIIII _'_

J

Foot Control

Sewing speed can be varied by the foot control.

The harder you press on the foot control, the faster the

machine runs.

Note:

The machine runs atthe maximum speed set bythe

speed controllever when the footcontrolis being fully

depressed.

Operation Instructions:

Foot Controller Model 21371 is used with Sewing Machine

Model 385.19010XXX (XXX represents numbers 000

through 999).

Note: 1

The Kenmore Elite sewing machine model 19010 is

equipped with an automatic shutdown safety feature to

prevent overheating. Follow safety instructions that appear

on the visual touch screen.

Pressure Dial

The pressure dial should be set at "3" for regular sewing.

Reduce the pressure to "2" for applique, cut work, drawn

work, basting and embroidery.

Set the pressure to "1" when sewing chiffon, lace, organdy

and other fine fabrics.

Velour and knits with a lot of stretch may also require a "1"

setting.

Turn the pressure dial (_ and set the desired number at the

setting _.

(_ Pressure dial

Setting mark

To Drop or Raise the Feed Dogs

The drop feed dogs lever is located underneath the free

arm bed on the back side of the machine.

To drop the feed dogs, push the lever in the direction

ofthe arrow, as illustrated.

To raise the feed dogs, push the lever in the direction

ofthe arrow, as illustrated, and turn the handwheet

toward you. Feed dogs must be up for normal sewing.

S

Illllll

J

Extension Table

• Detaching the table

Close the accessory box, and lift out the extension

table (_ toward you, as illustrated, for "_ree-arm" sewing.

(_ Extension table

• Attaching the table

Push the extension table (_ until it snaps intothe

machine.

(_ Extension table

Tabs

Holes

Free-arm sewing can be used for:

• Stitching sleeves, waistbands, pant legs or any tubular

garment area.

• Darning socks or mending knees, elbow or children's

wear.

In Conventional sewing set mode, you can adjust the free-

arm length. To adjust the free-arm length, please refer to

page 20.

Open the lid of the extension table and you can

conveniently store feet and accessories in the handy

compartments.

S

J

Presser Foot Lifter

(_ Presser foot lifter

The presser foot lifter raises and lowers the presser foot.

You can raise it higher than the normal up position for easy

removal of the presser foot or to help you place heavy fabric

under the foot.

f

J

Thread Cu_er s

(_Thread cuter

You do not need a pair of scissors to cut threads after

sewing. Just use the built-in thread cutter (_.

Changing Needle

Flat side

Needle clamp screw

Needle clamp

Turn offthe power switch.

Raise the needle to its highest position by turning the

handwheet counterclockwise, toward you, and lowering

the presser foot. Loosen the needle clamp screw _ by

turning it counterclockwise. Remove the needle from the

needle clamp _.

Insert a new needle into the needle clamp _ with the

fiat side (_ to the rear. When inserting the needle into

the needle clamp _, push it up as far as it goes. Tighten

the needle clamp screw _ firmly by turning it clockwise.

To check for a good needle, place the fiat side of the

needle onto something flat (needle plate, glass, etc.).

The gap between the needle and the fiat surface should

be consistent. Never use a bent or blunt needle.

A damaged needle can cause permanent snags or runs

in knits, fine silks and silk-like fabrics.

Changing Presser Foot

Snap-on button (red button)

Groove

• To remove

Raise the needle to its highest position by turning the

handwheel counterclockwise. Raise the presser foot, and

press the red button _ on the back of the foot holder.

• To attach

Place a selected presser foot so the pin _ on the foot lies

just under the groove _ on the foot holder. Lower the

presser bar to lock the foot in place.

J

S

Correcting Distorted Stitch Patterns

The sewing results of the stretch stitch patterns may vary

depending upon the sewing conditions, such as sewing

speed, type of the fabric, number of layers etc.

Always make test sewing on a scrap piece of the fabric that

you wish to use.

if decorative stitch patterns, letters, or numbers are

distorted, correct it with the feed balancing dial.

Notes:

• In normal sewing, set the feed balancing dial (_ to the

neutral position, i.e., the groove on the dial @ is

centered with the standard setting mark _.

• Turn the feed balancing dial (_ with a coin.

(_ Feed balancing dial

Groove on the dial

Standard setting mark

• Ifthe pattern is compressed, turn the dial in the direction

of "+".

• Ifthe pattern is drawn out, turn the dial in the direction

(_ Correct shape

Note:

Return the feed balancing dial (_ to its neutral position

when the sewing is finished.

S

V

+ -

J

Presser Foot Types

• zigzag foot (Foot A)

Use this foot for both straight and zigzag stitching.

• Straight stitch foot (Foot H)

Use this foot for exclusively for straight stitching with

center needle position.

• Automatic buttonhole foot (Foot R)

Use this foot for one step automatic buttonhole sewing.

Simply set a button on the guide of this foot and depress

the foot control. You can sew exactly the same length of

buttonhole as the button.

• Zipper foot (Foot E)

This foot can be set to sew on each side of the zipper.

The edge of the foot guides the zipper and keeps the

seam straight.

• Overedge foot (Foot C)

This foot is specially constructed for stitching and/or

overcasting seams. The small brush and wire guides help

control the fabric, hold the raw edge in place and keep it

from puckering, especially when sewing on knit fabrics.

• Satin stitch foot (Foot F)

Use this foot for satin stitch and outlining applique.

• Blind hem stitch foot (Foot G)

Use this foot for perfect blind hemming and topstitching.

The foot has ridges on the bottom to keep the fabric from

slipping and a screw on top to guide the folded edge of

your hem.

S

10

f

J

• 1/4"Seam foot (Foot O)

This foot is useful for patchwork quilt. The guide on the

foot maintains an exact 1/4" (0.7 cm) seam allowance.

S

• Embroidery foot (Foot P)

This foot is a special attachment for professional-style

embroidery.

J

•Walking foot

This is special attachment for hard-to-feed materials. This

foot effectively prevents fabrics from shifting and

puckering. It is great for quilting and matching plaids.

11

Selecting Needle and Fabric

For general sewing, use needle sizes 11 or 14. A fine thread and needle should be

used for sewing lightweight fabrics, so the fabric will not be marred. Heavy fabrics

require a needle large enough to pierce the fabric without fraying the needle thread.

In the needle set, there is one each of sizes 11, 14, 16, and 18, and a blue needle.

Use the blue needle to eliminate skipped stitches when sewing knits and synthetic

fabrics.

Special needles should be used on certain fabrics. A denim needle with a sharp tip

effectively pierces dense fabrics such as denim and canvas. For topstitching, a

special topstitching needle with a larger eye, accommodates heavier weight thread.

Leather needles punch small holes in leather and suede, allowing the thread to

follow through the hole.

Check your needles frequently for rough or blunt tips. Snags and runs in knits, fine

silks and silk-like fabrics are permanent, and are often caused by damaged

needles.

Always purchase a good quality thread. It should be strong, smooth and consistent

in thickness.

WEIGHT FABRIC TYPE OF NEEDLE NEEDLE SIZE

Chiffon, Georgette, Fine Lace, Organdy, Organdy Universal 9 (65)

Very Light Net, Tulle Ball Point 9 (65)

Batiste, Voile, Lawn, Pure Silk, Crepe de Chine, Orange 11 (75)

Sheer Crepe, Chambray, Handkerchief Linen, Blue 11 (75)

Gingham, Challis, Percale, Wool Crepe, Peau de Soie, 12 (80)

Taffeta, Satin, Silk Surah, Satin-backed Crepe,

Light Qiana

Blue 11 (75)

Single Knits, Jersey, Swimwear, Tricot

Ball Point 11 (75)

Leather, Suede Wedge Point Leather 11 (75)

Flannel, Velour, Velvet, Muslin, Velveteen, Poplin,

Corduroy, Broadcloth, Linen, Chintz, Gabardine, Felt, Red 14 (90)

Terry, Burlap, Quilted Fabrics

Medium Double Knits, (synthetic and natural) Stretch

Velour,

Stretch Terry, Ball Point 14 (90)

Sweater Knits

Leather, Vinyl, Suede Wedge Point Leather 14 (90)

Denim, Sailcloth, Ticking Denim 16 (100)

Double Faced Wool, Heavy Coating, Fake Fur, Purple 16 (100)

Heavy Drapery Fabrics

Leather, Suede Wedge Point Leather 16 (100)

Canvas, Duck, Upholstery Fabrics Green 18 (110)

11 (75)

All Topstitching for Special Finish Topstitching 14 (90)

12

Bobbin Winding

• Removing the hook cover plate

Hook cover plate release button

Hook cover plate

Bobbin

Slide the hook cover plate release button _ to the right,

and remove the cover plate _.

Lift out the bobbin _ from the bobbin holder.

• Horizontal spool pin

Spool pin

Large spool holder

Small spool holder

Lift up the spool pin _. Place a spool of thread on the

spool pin with the thread coming off the spool as shown.

Attach the large spool holder _, and press it firmly

against the spool of thread.

The small spool holder _ is used with narrow or small

spools of thread.

• Additional spool pin

Additional spool pin

Spool pin hole

Spool pin felt

Spool stand

The additional spool pin _ is for bobbin winding, without

unthreading the machine, and for twin needle sewing.

insert the additional spool pin _ into spool stand _ and

the hole _.

Place the felt _ and a spool on the pin as illustrated.

S

\

J

®

J

13

Bobbin Winding

Note:

Set the speed control lever at its fastest position for

bobbin winding.

_) Upper thread guide

Bobbin

Bobbin winder spindle

Guide the thread around the upper thread guide _).

Insert the thread through the hole on the bobbin _,

threading from the inside to the outside. Put the

bobbin on the bobbin winder spindle _.

Push the bobbin winder spindle _ to the right. The

visual touch screen shows "Bobbin Winding".

With the free end of the thread held in your hand,

depress the foot control. Stop the machine when

the bobbin has made a few turns, and cut the

thread close to the hole on the bobbin.

Depress the foot control again. When the bobbin is

fully wound, it wilt stop automatically. Return the

bobbin to its original position by moving the spindle

to the left, and cut the thread as shown.

S

,,.mditil

J

14

Page is loading ...

Sears 010 User manual

Sears 010 User manual

Related papers

Other documents