Owner’s Manual
MOON
Series
320
S
Power Supply
320 S Power Supply
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or another apparatus that produces
heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one
wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third
prong is provided for safety. If the provided plug does not fit into the outlet, consult an electrician for replacement of
the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus. Unplug mains cord during transportation.
11. Only use attachments and accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as when the power cord or plug has been damaged; liquid has been spilled or objects have fallen into the
apparatus; or the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. No naked flame sources, such as candles, should be placed on the apparatus.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
____________________________________________________________________________________
320 S Power Supply
Important Safety Instructions (cont’d)
The lightning flash with the arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
Marking by the “CE” symbol (shown left) indicates compliance of this device with the
EMC (Electromagnetic Compatibility) and LVD (Low Voltage Directive) standards of the
European Community
Please read all instructions and precautions carefully and completely before
operating your Simaudio MOON 320S Power Supply.
1. ALWAYS disconnect your entire system from the AC mains before connecting or disconnecting any cables,
or when cleaning any component. To completely disconnect this apparatus from the AC mains, disconnect
the power supply cord plug from the AC receptacle.
2. The MOON 320S must be terminated with a three-conductor AC mains power cord which includes an earth
ground connection. To prevent shock hazard, all three connections must ALWAYS be used. Connect the
MOON 320S only to an AC source of the proper voltage; Both the shipping box and rear panel serial number
label will indicate the correct voltage. Use of any other voltage will likely damage the unit and void the
warranty
3. AC extension cords are NOT recommended for use with this product. The mains plug of the power supply
cord shall remain readily accessible.
4. NEVER use flammable or combustible chemicals for cleaning audio components.
5. NEVER operate the MOON 320S with any covers removed. There are no user-serviceable parts inside. An
open unit, especially if it is still connected to an AC source, presents a potentially lethal shock hazard. Refer
all questions to authorized service personnel only.
6. NEVER wet the inside of the MOON 320S with any liquid. If a liquid substance does enter your MOON 320S,
immediately disconnect it from the AC mains and take it to your MOON dealer for a complete check-up.
7. NEVER spill or pour liquids directly onto the MOON 320S.
8. NEVER block air flow through ventilation slots or heatsinks.
9. NEVER bypass any fuse.
10. NEVER replace any fuse with a value or type other than those specified
11. NEVER attempt to repair the MOON 320S. If a problem occurs contact your MOON dealer.
12. NEVER expose the MOON 320S to extremely high or low temperatures.
13. NEVER operate the MOON 320S in an explosive atmosphere.
14. ALWAYS keep electrical equipment out of reach of children.
15. ALWAYS unplug sensitive electronic equipment during lightning storms.
16. WARNING: Do not expose batteries or battery pack to excessive heat such as sunshine, or fire or the like.
____________________________________________________________________________________
320 S Power Supply
Table of Contents
Introduction .................................................... 6
Unpacking ....................................................... 7
Installation & Placement ................................... 7
310LP Internal Settings ..................................... 8
Rear Panel Connections ..................................... 9
Operating the 320S .........................................10
Specifications .................................................11
www.simaudio.com
Simaudio Ltd., 1345 Newton Road
Boucherville, Quebec J4B 5H2 CANADA
Date Code: 20141001
____________________________________________________________________________________
320 S Power Supply
____________________________________________________________________________________
6
Introduction
Thank you for selecting the MOON 320S Power
Supply as a part of your music system. This
component has been designed to offer state-of-the-
art high-end performance in an elegant package,
while retaining all the sonic hallmarks on which
Simaudio has made its reputation. We have spared
no effort to ensure that it is provides a significant
improvement to the sonic performance of your
MOON 310LP Phono Preamplifier. We have
been building high-performance audio equipment for
almost 30 years, and the know-how gained through
our cumulative experience is an important reason
why MOON audio components are so musically
satisfying.
The performance of your 320S will continue to
improve during the first 200 hours of use. This is
the result of a “break-in” period required for the
numerous high quality electronic parts used
throughout this Power Supply.
We hope you enjoy using the MOON 320S Power
Supply as much as the pride we have taken in
creating this fine audio product. We understand the
power and emotion of music and build our products
with the goal of faithfully capturing these elusive
qualities.
The information contained in this manual is subject
to change without notice. The most current version
of this manual is available on our official website at
http://www.simaudio.com
IMPORTANT !
Before setting up your new MOON 320S, there are mandatory internal adjustments
that must be made to the 310LP Phono Preamplifier! Failure to make the
adjustments before connecting it to the 320S may result in damage that is not
covered by warranty! Refer to page 8 of this manual for instructions.
Your MOON 320S Power Supply incorporates many significant design features to achieve its “world class” level
of performance. This is an abbreviated list of the more important features:
High quality toroidal transformer.
4 stages of DC voltage regulation.
Total capacitance of 35,200uF.
Dual choke inductance (2x 200mH).
Special "pi-type" filter after initial voltage rectification
stage to reduce AC transmission noise.
Dual action voltage regulation system to further lower
noise.
DC signal noise is 150dB lower within 310LP circuitry.
Reduces the 310LP’s signal-to-noise ratio by over
3dB, regardless of its selected internal gain setting.
Pure copper circuit board tracings with extremely low
impedance characteristics.
Accurate matching of the finest high quality electronic
components.
Designed to be powered up at all times for optimal
performance.
Low operating temperature for a longer than normal
life expectancy.
320 S Power Supply
____________________________________________________________________________________
7
Unpacking
The MOON 320S phono preamplifier should be removed from its box with care.
The following accessories should be included inside the box with your power supply:
9
DC 4-pin XLR cable
9
This owner’s manual
9
Warranty and product registration information (USA and Canada only)
Once the MOON 320S is unpacked, inspect it
thoroughly and report any damage to your dealer
immediately. We suggest that you keep all of the
original packaging, storing it in a safe, dry place in
case you’re required to transport this product. The
customized packaging is specially designed to
protect the 320S from any potential damage during
transit.
Please write the serial number of your new MOON 320S in the space provided below for future reference.
Serial No.: ________________
Installation & Placement
The MOON 320S has been designed to be placed
side-by-side with the MOON 310LP. Together, these
2 components will fit easily on any standard audio
equipment shelving system. As well, feel free to
experiment with other placement options for the
best possible setup that meets your needs.
320 S Power Supply
____________________________________________________________________________________
8
310LP Internal Settings
A B A B
Figure 1: MOON 310LP Circuit Board layout
Prior to connecting your MOON 310LP Phono
Preamplifier to the MOON 320S Power Supply,
you must move two (2) internal jumpers inside your
MOON 310LP. Please refer to page 13 of your
MOON 310LP owner’s manual for detailed
instructions on how to remove the chassis cover.
Referring to the above diagram of the 310LP, you
will see an array of four (4) jumper sockets labeled
STR1, STR2, STR3 and STR4. The factory default
position for the 2 jumpers is in sockets STR2 and
STR4 (positions B in figure 1). To properly operate
the MOON 310LP in conjunction with the MOON
320S, you will need to move these 2 jumpers into
sockets STR1 and STR3 (positions A in figure 1).
Failure to make these adjustments may cause
damage that is not covered by warranty.
320 S Power Supply
____________________________________________________________________________________
9
Rear Panel Connections
Figure 2: MOON 310LP Rear panel Figure 3: MOON 320S Rear panel
The rear panel of the MOON 320S will look similar
to Figure 3 (above right). There is a 4-pin female
XLR connector, labeled “DC output”, located on the
left side. On the right side are the the power “main
switch” and IEC receptacle, labeled “AC Input”.
To connect the MOON 310LP Phono Preamplifier to the MOON 320S Power Supply, follow these steps:
1. Disconnect the AC power cord from your MOON
310LP.
2. Use the supplied DC 4-pin XLR cable to connect
the “DC Output” on the MOON 320S to the “DC
Power” input on the MOON 310LP. The male
end (with 4 pins) of the cable connects to the
MOON 320S and the female end (with 4 holes)
connects to the MOON 310LP. Do not use an
aftermarket or custom 4-pin XLR cable as the
supplied cable is specifically designed for this
application.
3. Connect the MOON 310LP’s AC power cable to
the IEC receptacle, located on the 320S’s rear
panel. Ensure that the AC wall outlet you use
has a functioning ground. For the best sonic
performance, it is preferable that you plug your
320S directly into a dedicated AC outlet and
avoid using an extension cord. If you have the
time and willingness, consider installing a
superior quality AC wall outlet such as a hospital
grade Hubbell.
4. In order to obtain the maximum performance
from your audio system, we strongly
recommend that the detachable power cord not
come into physical contact with any of the
interconnect cables from your audio system. In
the event that this can’t be avoided, you should
ensure that any cables coming into contact with
each other are crossed at ninety degree angle to
minimize the contact area.
320 S Power Supply
____________________________________________________________________________________
10
Operating the 320S
Since your MOON 310LP Phono Preamplifier is
not equipped with its own on/off power switch,
powering it on and off is accomplished via the
MOON 320S Power Supply’s on/off switch,
located on the rear panel.
We recommend that you leave your MOON 320S
Power Supply powered up at all times to maintain
optimal sonic performance. In the event that you
plan to be away from your home for a few days,
powering off the MOON 320S may not be a bad
idea. Once fully “broken-in”, please keep in mind
that both your MOON 320S and MOON 310LP will
require several hours of playing time before they
reach peak performance again.
Turning on your MOON 320S for the first time
Prior to making the AC connection for the first time,
make sure that every cable is properly connected to
avoid any problems. Once the 320S is connected to
an AC source you may power it up by flicking the
main rocker switch labeled “POWER” to the ‘1’ (on)
position. The blue LEDs on the front panel of both
the MOON 320S and MOON 310LP will illuminate
at the same time.
On and Off Sequence
To avoid having any annoying noises (ie. “thumps”
and “pops”) emanate from your speakers when
powering your 320S on or off, you should always
power up your 320S before powering up your
preamplifier or integrated amplifier. As well, always
power down your 320S after powering down your
preamplifier or integrated amplifier.
Note: When you power down the MOON 320S, the
blue LEDs on both units will remain illuminated for
up to 10 seconds; this is normal and is the result of
the large amount of storage capacitance found in
the MOON 320S Power Supply.
320 S Power Supply
____________________________________________________________________________________
11
Specifications
MOON 320S:
Transformer ......................................................... 25VA
Total Capacitance ................................................ 35,200µF
Total Inductance .................................................. 400mH
Power Consumption .............................................. 9 Watts
AC Power Requirements ....................................... 120V or 240V, 60Hz or 50Hz
Shipping Weight .................................................. 8 lbs / 3.5 Kgs
Dimensions (W x H x D, inches) ........................... 8 x 3.25 x 11
MOON 310LP:
Signal-to-Noise Ratio (full scale @ 40dB gain) ....... 114dBr
Signal-to-Noise Ratio (full scale @ 66dB gain) ....... 92dBr
Note: All other MOON 310LP specifications remain unchanged
when using it in conjunction with the MOON 320S.
Fusibles de Remplacement: Version 120V = 0.2A Retardé (5 x 20mm)
Version 230V = 0.1A Retardé (5 x 20mm
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
moon 320S User manual
- Category
- Supplementary music equipment
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Mark Levinson 320S Owner's manual
-
Genius LOOK 320S Owner's manual
-
Braun 320s-4 User manual
-
Braun 360s-4, 330s-4, 320s-4, Series 3 User manual
-
Redring Active User manual
-
Stealth Cam STC-DVSIR5 Prowler DVS User manual
-
MIMAKI JV5-320DS Specification
-
-
-
