Kenmore Kenmore 580.74103 Owner's manual

Brand: Kenmore

Model: Kenmore 580.74103

Category: Split-system air conditioners

Type: Owner's manual

This manual is also suitable for

Owner's Manual

Manual del Propietario

THROUGH-THE-WALLAIRCONDITIONER

ACONDICIONADODEAIREATRAVESDEPARED

Model, Modelo 580.73083 580.74103 580.74123

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.com

TABLE OF CONTENTS ........................2

WARRANTY ..............................................2

SAFETY .....................................................3

ImportantSafety Instructions...................... 3

ELECTRICAL REQUIREMENTS .......4

INSTALLATION ........................................5

Installation Requirements ......................... 5

Installation ................................................ 6

Procedure A ............................................. 7

Procedure B ............................................. 9

Procedure C .......................... ._............... 11

OPERATION ........................................... 12

How and Why ......................................... 12

Normal Sounds ...................................... 12

Capacity and Running Time ................... 12

Features ................................................. 13

Using the Air Conditioner ....................... 13

Air Conditioner Features ........................ 14

MAINTENANCE ..................................... 17

Air Filter Cleaning ................................... 17

Air Conditioner Cleaning ........................ 17

How to Remove the Front Grille ............. 17

How to Replace the Front Grille ............. 17

TROUBLESHOOTING ......................... 18

Before Calling for Service ...................... 18

ESPAI_IOL ................................................ 2o

MASTER PROTECTION

AGREEMENTS ......................................39

SERVICE NUMBERS ............BackCover

FULL ONE YEAR WARRANTY ON

THROUGH-THE-WALL AIR CONDITIONER

For one year from the date of purchase, when this

air conditioner is operated and maintained for

normal room cooling according to instructions in this

owner's manual, Sears will repair this air

conditioner, free of charge, if defective in material or

workmanship.

FULL FIVE-YEAR WARRANTY ON

SEALED REFRIGERATION SYSTEM

For five years from the date of purchase, when this

air conditioner is operated and maintained for

normal room cooling according to instructions in this

owner's manual, Sears will repair the sealed

refrigeration system (consisting of refrigerant,

connecting tubing, and compressor), free of charge,

if defective in material or workmanship.

WARRANTY SERVICE IS AVAILABLE BY

CONTACTING SEARS SERVICE AT

1-800-4-MY-HOME ®.

Warranty coverage applies only to air conditioners

used for non-commercial, private household

purposes.

This warranty applies onlywhile this product is in

use in the United States.

This warranty gives you specific legal rights, and

you may also have other rights which vary from

state to state.

Sears, Roebuck and Co., D/817WA,

Hoffman Estates, IL 60179 U.S.A.

-2-

IMPORTANT SAFETY INSTRUCTIONS

The safety instructions below will tell you how to use your room air conditioner to avoid harm to yourself or

damage to yourROOM AIRCONDITIONER.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable

vapors and liquids in the vicinityof this or any other

appliance. Read product labels for flammability and

other warnings.

PREVENT ACCIDENTS

To reduce the risk of fire, electrical shock, or injury

to persons when using your air conditioner, follow

basic precautions, including the following:

• Be sure the electrical service is adequate for the

model you have chosen.

• If the air conditioner is to be installed in a window,

you will probably want to clean both sides of the

glass first. If the window is a triple-track type with a

screen panel included, you may want to remove

the screen completely before installation.

• Be sure the air conditioner has been securely and

correctly installed according to the instructions in

this manual.

Save this manual and installation instructions for

possible future use in removing or reinstalling this

unit.

• Use gloves when handling the air conditioner.

Be careful to avoid cuts from sharp metal fins on

front and rear coils.

Y_ ELECTRICAL INFORMATION

The complete electrical rating of your new room air

conditioner is stated on the serial plate. Refer to the

rating when checking the electrical requirements.

• Be sure the air conditioner is properly grounded.

To minimize shock and fire hazards, proper

grounding is important. The power cord is

equipped with a three-prong grounding plug for

protection against shock hazards.

• Your air conditioner must be plugged into a

properly grounded wall receptacle. If the wall

receptacle you intend to use is not adequately

grounded or protected by a time delay fuse or

circuit breaker, have a qualified electrician install

the proper receptacle.

• Do not run air conditioner with packing sheet of

the back of the sleeve, and packing corner and

blue tape of the air conditioner. This could result in

mechanical damage within the air conditioner.

• Do not use an extension cord or an adapter

plug.

_ Avoid fire hazard or electric shock.

Do not use an extension cord or an adapter plug.

Do not remove any prong from the power cord.

Grounding type

walkreceptacle Do not under any

circumstances cut,

remove, or bypass

the grounding prong

from this plug.

P°wet;,%;o Zr

grounding plug

ENERGY SAVING IDEAS

• The capacity of the room air conditioner must fit

the room size for efficient and satisfactory

operation.

• Install the room air conditioner on the shady side

of your home. A window that faces north is best

because it is shaded most of the day.

• Do not block air flow inside with blinds, curtains, or

furniture; or outside with shrubs, enclosures, or

other buildings.

• Close the floor and wall registers and the fireplace

damper so cool air does not escape up the

chimney and into the duct work.

• Keep blinds and drapes in other windows closed

during the sunniest part of the day.

• Clean the air filter as recommended in the

MAINTENANCE section of this manual.

• Proper insulation and weather stripping in your

home will help keep warm air out and cool air in.

• External house shading with trees, plants or

awnings will help reduce the air conditioner's work

load.

• Operate heat producing appliances such as

ranges, washers, dryers, and dishwashers during

the coolest part of the day.

-3-

OBSERVE ALL LOCAL CODES AND

ORDINANCES.

DO NOT, UNDER ANY CIRCUMSTANCES,

REMOVE THE POWER SUPPLY CORD

GROUND PRONG,

ELECTRICAL GROUND IS REQUIRED ON

THIS APPLIANCE.

A 208/230-volt 60 Hz, AC only, 15A fused and

properly grounded electrical supply is required.

A time delay fuse or time delay circuit breaker

is recommended. Use a dedicated circuit,

serving only this appliance.

DO NOT USE AN EXTENSION CORD.

RECOMMENDED GROUNDINGMETHOD

For your personal safety, this appliance must

be grounded. This appliance has a power

supply cord with a 3-prong grounding plug. To

minimize possible shock hazard, the cord must

be plugged into a mating grounding type wall

receptacle and grounded in accordance with

the National Electrical Code (ANSI/NFPA 70)

latest edition and all local codes and

ordinances. If a mating wall receptacle is not

available, itis the personal responsibility and

obligation of the customer to have a properly

grounded 3-prong wall receptacle installed by a

qualified electrician.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructionscan result

in death, fire, or electrical shock.

Ground

prong I'/ "_ _)

r I",_ _1 _-3-pr°ng

3 ron _-, _ \'--J J grounding

"P g I I tvee wall

grounding ]_ _ i[ ---

plug receptacle

Power_

supply

cord

-4-

Removepackingsheetfrom the backofthe sleeve,and

packingcomer and bluetape fromthe airconditioner.

INSTALLATION REQUIREMENTS

If you use an existing wall sleeve, youshould

measureitsdimensions.

Install thenewairconditioneraccordingtothese

installationinstructionsto achievethebest

performance.Allwallsleevesusedto mountthe

newairconditionermustbe ingoodstructural

conditionand havea reargrilletosecurelyattach

thenewairconditioner.(FIG. 1)

With the Kenmoresleeve, youcanmaintainthe

bestperformanceofthenewair conditioner.(FIG.2)

(366ram)

!8"(458 ram)

Air Conditioner . FIG. 1

INSTALLATION HARDWARE

2Size options

ITEM NAMEOF PARTS Oq'Y

O PLASTIC GRILLE f

HORIZONTALINSULATION STRIPS 2

_) AROUND INSULATION STRIPS 2

_) SUPPORT BLOCK 2

BAFFLE 1

(_ TRIM FRAME 2

(_ SHIM 2

(_) PLASTICNUTSAND WASHERSCREWS 4

Expanded

aluminum metal g_itlc

/. (425m'_l

Kenmore Wall Sleeve FIG.2

ELECTRICAL SERVICE

Check your available electrical service. The power

supply available must be the same as that shown

on the unit nameplate (found on left side ofcabinet).

All models are equipped with a 3-prong service plug

to provide proper service and safe positive

grounding. Do not change plug in any way. Do not

use an adapter plug. If your present wall outlet does

not match your plug, calf a qualified electrician to

make the necessary corrections. SAVE CARTON

for storage and this OWNER'S MANUAL for future

reference. The carton is the best way to store unit

during winter or when not in use.

To avoid risk of personalinjury, property damage,

or product damage due to the weightofthis

device and sharp edges that maybe exposed:

• Air conditioners covered in this manualpose an

excessive weight hazard. Two or more people

are needed to move and install the unit.

To prevent injury or strain, use proper lifting and

carrying techniques when moving unit.

• Carefully inspectlocation where air conditioner

will be installed. Be sure itwill support the weight

of the unit overan extended period of time.

•Handle air conditioner with care. Wear

protective gloves whenever lifting or carrying the

unit. AVOID the sharp metal fins of front and

rear coils.

• Make sureair conditioner does not fall during

installation.

REQUIRED TOOLS:

• Tight Fitting gloves

• Standard screwdriver

• Phillips screwdriver

• Pliers

• Sharp knife

• 3/8-inch open end

wrench or adjustable

wrench

• 1/4-inch hex socket

and ratchet

• Tape measure

• Electric drill

• 1/4-inch drill bit

-5-

INSTALLATION

We strongly recommend the removalof the

old wall sleeveand the installation of a new

Kenmore Wall Sleeve.

If youdecideto keepthe existingwallsleeve,

youhavetoredirectthe louversat thebackofthe

wall sleeveillustration.The useofpliersis

recommended.Ifyou DO NOT redirect,you run

theriskof poorperformanceor productfailure.

Thisisnotcoveredunderthetermsofthe

Kenmorewarranty.

• Pick a location which will allow the conditioned air

to blow into the area you want. Good installation

with special attention to the proper position of the

unit will lessen the chance that service will be

needed.

ITEMS IN INSTALLATION HARDWARE

You may not need all parts in the kit. Discard

unused pads

ITEM (inches)

Plastic grille 263/4x 161/2

Horizontal Insulation Stripe113/8x s/8x

273/16

13/8 X 13/8 X 273/16

Around Insulation Strips 13/8x 3/4x 611/2

1% x 1% x 611/2

Support Block 13/4x 1% x 451m

Baffle 14 x 41/2x 1/8

Shim 13x lx3/4

Trim Frame

Washer Screw

Nuts(Plastic)

Qty.

HOW TO INSTALL

li]l Identify the existing wall sleeve before installing

the unitfrom the listed below.

Brand

White-Westinghous_

Frigidaire

Carrier (52F series)

General Electric

/Hotpoint

Whirlpool

Fedders/Emerson

Sears/Kenmore

Emerson/Fedders

Carrier (51S Series)

Friedrich

Wall Sleeve Dimensions (inches_,

Width Height Depth

25-1/2 15-1/4 16, 17-1/2

or 22

26 15-5/8 16-7/8

17-1/8

25-7/8 16-1/2

or 23

27 16-3/4 16-3/4

or 19-3/4

25-7/8 15-17/32 16-23/32

26-3/4 15-3/4 15

25-3/4 16-7/8 18-5/8

27 16-3/4 16-3/4

NOTE: All wall sleeves used to mount the new Air

Conditioner must be in sound structural condition

and have a rear grille that securely attaches to

sleeve, or rear flange that serves as a stop for the

Air Conditioner,

[]Remove old air conditioner from existing wall

sleeve.

_1 Clean the interior of an existing sleeve.

(Do not disturb seals.)

Q Wall sleeve must be securely fastened in wall

before installing the air conditioner. Use the

nails or screws through sleeve into wall, if

needed. Repaint sleeve if needed.

!_ Prepare the wall sleeve for installation of the

unit. If you plan to use your existing wall sleeve,

and itis not Kenmore, use procedure B or C

below.

Procedure

Brand

Sears/Kenmore

White-Westinghouse

Frigidaire Carrier

(52F series)

General Electric

/Hotpoint

Whirlpool

Carrier (51S series)

Depth(inches)

16-23/32

16, 17-1/2

or 22

16-7/8

Fedders/Emerson

Emerson/Fedders

Friedrich

_r_ Install new unit intowall sleeve.

CAUTION: When installation is completed,

replacement unit MUST have a rearward slope as

shown.

17-1/8 or 23

18-5/8

16-3/4

or 19-3/4

16-3/4

UNIT Wall Sleeve

FRONT"_ 1- -_............. i

114" i _ ............. i

FIG. 3

-6-

PROCEDURE A

] If you are using the new sleeve supplied with

your unit, skip to step 3. Otherwise, install the

plastic grilla from the kit.Cut the plastic grille to

25-1/2" wide and 15-1/4" high. Place the

plastic grille to the inside ofthe wall sleeve at

the rear flange.

FIG. 4

O Fasten the 4 washer screws to secure the grille

to the wall sleeve. Ifyou need plastic nuts to

mount plastic grille to the inside of the wall

sleeve, there are plastic nuts in the installation

kit. The nuts are installed from the inside of the

sleeve and are pressed into the square holes of

the rear flanges.

FIG. 5

L_ Install the new unit into the wall sleeve.

IL_To assemble trim, snap the tab of each piece

into the slot of the other piece as shown below.

Slide trim over the front of the air conditioner

until trim is flush with sleeve as shown below.

Trim (2 ea)

Wall

FIG. 7

I_ Remove the backing from the Horizontal

Insulation strip 13/8x 3/8 X 273!16 and attach that

to the inside bottom of the sleeve as shown

below. Remove the backing from the Around

Insulation strip 1% x 3/4x 61 _2and attach that

to the inside front of the sleeve as shown

below.

FIG. 6

• Airconditionerscovered inthis manual pose

an excessive weighthazard. Two or more

people are needed to move and install the unit.

To prevent injury or strain, use proper lifting

and carrying techniques when moving unit.

• When handling the air conditioner, be careful

to avoid cuts from sharp metal fins on front and

rear coils.

• Make sure air conditioner does not fall during

removal.

-7-

PROCEDURE B

_1 Redirsct the louvers at the back of the wall

sleeve to 60° angle as shown in the FIG 8. The

use of pliers is recommended.

7 5/16"

\\\\\\\\\\\\\\\\\\\_

Rear Louve_'s

(Top View)

FIG. 8

_'_lf the wall sleeve already has a rear grille, skip

to step 4. Ifthe wall sleeve does-not have a rear

grille or Iouvered panel, install the plastic gdlle

from the kit. Cut the plastic gdlle to 25-1/2" wide

and 15-1/4" high. Place the plastic gdlle to the

inside of the wall sleeve at the rear flange.

Place the plastic grille FIG. 9

IL_I Fasten the 4 washer screws to secure the grille

to the wall sleeve. If you need plastic nuts to

mount plastic grille to the inside of the wall

steeve, there are plastic nuts in the installation

kit.The nuts are installed from the inside of the

sleeve and are pressed into the square holes of

the rear flanges.

Fasten the screws

FIG. 10

_J Remove the backing from the Horizontal

Insulation strip 13/8x % x 273/lSand attach that

to the inside bottom of the sleeve as shown

below. Remove the backing from the Around

Insulation strip 13/8x 3/4x 611/2and attach that to

the inside front of the sleeve as shown below.

FIG. 11

_-"_ Ifthe depth of your existing wall sleeve is less

than or equal to 18", skip to step 7. Otherwise,

cut the baffles and the support blocks according

to length "A" in the table below.

Depth"D"ofthe existing Length"A"

wallsleeve (inches) (inches)

18<D<_18-% 3/4

18-%<D_<19-3/4 1-3/4

19-3/4<D_<22 4

Support

Block

_]_F laffle

IG. 12

r_ Remove the backing from the support blocks

and attach them to the inside of the wall sleeve

as shown FIG 9. Slide the baffle into slots of the

support blocks.

Block

FIG. 13

_"_ Install the new unitinto the wall sleeve.

-8-

PROCEDURE B

_lTo assembletrim,snapthetabof eachpiece

intotheslotoftheotherpieceas shownbelow.

Slidetrimoverthefrontoftheair conditioner

untiltrimisflush withsleeveas shownbelow.

Trim (2 ea)

Wall

FIG. 14

• Air conditionerscoveredinthis manualpose

an excessiveweighthazard. Two or more

peopleare neededtomoveand installthe unit.

To preventinjuryorstrain,useproperlifting

and carryingtechniqueswhen movingunit.

When handlingthe air conditioner,becareful

toavoidcutsfrom sharpmetalfins on front and

rear coils.

Make sureair conditionerdoes notfall during

removal.

-9-

PROCEDURE C

il Redirect the louvers at the back ofthe wall

sleeve to 60° angle as shown in the FIG 15.

The use of pliers is recommended.

7 13116"

,\\\\\\\\\\\\\\\\\\_

Rear Louvers

(Top View)

FIG. 15

_'_lf the wall sleeve already has a rear grille, skip

to step 4. If the wall sleeve does-not have a rear

grille or Iouvered panel, install the plastic grille

from the kit. Cut the plastic grille to 26-1/2" wide

and 15-1/2" high. Place the plastic grille to the

inside of the wall sleeve at the rear flange.

Place the plastic grille

FIG. 16

I_'1 Fasten the 4 washer screws to secure the grille

to the wall sleeve. Ifyou need plastic nuts to

mount plastic grille to the inside of the wall

sleeve, there are plastic nuts in the installation

kit. The nuts are installed from the inside of the

sleeve and are pressed into the square holes of

the rear flanges.

Fasten the screws FIG. 17

L_! Remove the backing from the Horizontal

Insulation stdp 13/8x 13/ex 273j16and attach that

to the inside bottom of the sleeve as shown

below. Remove the backing from the Around

Insulation stdp 13/8x 13/8x 611/2and attach that

to the inside front ofthe sleeve as shown below.

FIG. 18

_lf the depth of your existing sleeve is less than

or equal to 18", skip to step 7. Otherwise, cut

the baffles and the support blocks according to

Length "A" in the table below.

Depth"D"of the existing Length"A"

wallsleeve (inches) (inches)

18<D<18-% 3/4

18-%<D_<19-_/4 1-3/4

19-3/4<D_<22 4

- upport

Block

_F _affle

IG. 19

r_ Remove the backing from the support blocks

and attach them to the inside ofthe wall sleeve

as shown FIG 20. Slide the baffle into slots of

the support blocks

Vail

(7 t3/16" )

Support

Block

FIG. 20

-10-

PROCEDURE C

N Remove the backing from the 13" shim strips

and attach them as shown below in Fig. 22.

The higher portion of shim is to be placed in

front of the rib on the base ofwall sleeve.

1" high_ II 3/4"High

FIG. 21

FIG. 22

_J Install the new unit into the wall sleeve

_'ITo assemble trim, snap the tab of each piece

into the slot of the other piece as shown below.

Slide trim over the front of the air conditioner

until trim is flush with sleeve as shown below.

Trim (2 ea)

Wall

FIG. 23

• Airconditioners coveredinthis manual pose

anexcessive weighthazard.Two or more

peopleare neededtomoveand installtheunit.

To preventinjuryor strain,use properlifting

andcarryingtechniqueswhenmovingunit.

• When handling theair conditioner,becareful

to avoidcutsfrom sharpmetalfins on front and

rearcoils.

• Makesure airconditionerdoes notfailduring

removal.

-11 -

HOW AND WHY

Your room air conditioner provides the following

functions to make hot weather living more

comfortable:

• Cools and circulates room air.

• Lowers humidity by removing excess moisture.

• Filters out summertime dust, dirt, and some

airborne impurities.

The air conditioner performs these functions by

drawing room air through a filter which traps dust

and dirt particles. The air then passes over a

cooling coilwhich refrigerates the air and removes

excess moisture. The same air isthen returned to

the room- cooler, drier, and cleaner. Moisture

removed from the room air is carried to the outside

and evaporated.

Your air conditioner isdesigned to be easy to

operate and to provide plenty of cooling power.

NORMAL SOUNDS FIG24

Aside from the regular fan motor and compressor

sounds coming from your air conditioner, you will

once in a while hear a pingingsound. This is the

resultof moisture being picked up from the air in the

room and thrown against the air conditioner'sfan.

This is normal and should not be cause for concern.

Also, do notbe alarmed if you hear a slight hissingor

gurgling sound coming from your air conditionerafter

it is off.These are normal coolant noises.

CAPACITY AND RUNNING TIME

Proper unitsize is important in deciding the desired

comfort for the area you want to cool. The proper

size isdetermined by the number of square feet in

the area to be cooled.

Whenever the heat or humidity load is above normal

the air conditioner must run longer and more often

to keep the desired temperature you have selected.

Under heavy heat load conditions the air conditioner

may need to run constantly to keep the temperature

you want.

At times using the MED FAN setting to circulate the

room air may make it comfortable even though you

do not have the air conditioner set to cool the air,

This will decrease your cost of use,

-Fan

- Unit Vibration

The unit may vibrate

and make noise

because of poor wall

or window

construction.

You may hear air

movement from the

fan.

The modem high

efficiencycompressor

may havea highpitched

hum orpulsatingnoise

thatcycleson andoff.

You may hear

droplets of water

hitting the condenser,

causing a pingingor

clickingsound.

FIG. 24

-12-

FEATURES

THE UNIT

1 5 736284

1. CABINET

2. HORIZONTAL AIR DEFLECTOR

(Vertical Louver)

3. VERTICAL AIR DEFLECTOR

(Horizontal Louver)

4. AIR DISCHARGE

5. FRONT GRILLE

6. INLET GRILLE (Air Intake)

7. AIR FILTER

8. VENT CONTROL

THE SLEEVE AND THE REAR GRILLE

FIG. 25

FIG, 26

USING THE AIR CONDITIONER

_To reduce the risk of fire, electric

shock, or injury to persons, read the important

SAFETY instructions section before operating this

appliance.

To begin operating the air conditioner after

installation, follow these steps:

1. Plug in the air conditioner. (To prevent electrical

hazards, do not use an extension cord or an

adapter plug.)

2. Set the TEMP control tothe coolest setting.

3. Set the MODE control at the highest COOL level

4. Adjust the louvers for comfortable air flow.

5. Once the room has cooled, adjust the TEMP and

MODE control to the setting you find most

comfortable.

NOTE : If the air conditioner is turned off, wait 3

minutes before restarting. This allows pressure

inside the compressor to equalize. Failure to wait 3

minutes before restarting may cause inefficient

operation.

If you move the TEMP control to a warmer, then

immediately back to a cooler setting, the unit will

shut off. Wait 3 minutes before restarting.

Refer to the AIR CONDITIONER FEATURES

section for other settings.

VENT CONTROL

The Vent Control allows the air conditioner to either

recirculate inside air (CLOSE) or exhaust air to the

outside (OPEN). (FIG. 27)

• The CLOSE position is used when maximum

cooling is desired. It may also be used for air

recirculation without cooling when the air

conditioner is set in the FAN position.

• The OPEN position removes stale air from the

room and exhausts itto the outside. Fresh air is

drawn intothe room through your home's normal

air passages.

• The OPEN or CLOSE position can be used with

any fan selection.

9. SLEEVE ASSEMBLY

(Including Expanded Aluminum Rear grille)

10. REAR GRILLE

(Expanded Aluminum Rear grille)

PULL OPEN / PUSH CLOSE

FIG. 27

-13-

DISPLAY

Cool •

Energy ==

Saver w

Fan •

Timer • TEMP O

C-TIMER

- SHUT-OFFTIME

• Youwillusuallyuseshut-ofttimewhileyousleep.

• Withunitrunning,useTimerto setnumberofhours

untilshut-off.

• Foryoursleepingcomfort,onceTimeisset,the

Temperaturesettingwillraise2°F after30 rain.,

and 2°F afteranother30 rain.

• EverytimeyoupushTimerbutton,itadvancesthe

Timersettingas follows:1 Hour-, 2 Hours_ """

12 Hoursmaximum.

- START TIME

•With unit not running,use Timer to set number of

hours before untilstarts.

• Every time you push Timer button, it advancesthe

Timer setting as follows: 1 Hour_ 2 Hours --,......

12 Hours maximum.

REMOTE CONTROL SIGNAL

RECEIVER

j TEMPERATURE SETTING

Usethisbuttontoautomaticaltycontrolthe

temperatureoftheroom.

Thetemperaturecanbesetwithina range

of60°Fto86°F byincrementsofI°F.

-- POWER

To turntheair conditionerON, pushthis

button.

To turntheair conditionerOFF, pushthe

buttonagain.

•Thisbuttontakespriorityoveranyother

button.

•When youfirst turn iton, the unit is in

cool mode, High fan speed, Temperature

setting at 72°F.

_-- FAN SPEED

• Everytimeyoupushthisbuttonit

advancesthesettingasfollows:

{High-' Low_ Med-, High}

MODE

- Everytimeyoupushthisbutton,itwillshiftamongCOOL, ENERGYSAVER and FAN.

- ENERGY SAVER:

• Thefan stopswhenthecompressorstopscooling.Approximatelyevery3 minutesthefan willturnonand

the unitwillchecktheroom airtodetermineifcoolingisneeded.

When power is restored after an electrical power failure, the unit will begin to run at its last setting. |

-14-

REMOTE CONTROL

NOTE: The Remote Control will not operate properly if strong lightshines on the sensor window of the Air

Conditioner or ifthere are obstacles between the Remote Control and the Air Conditioner.

Every time you push button, you will hear a beep from the Air Conditioner.

POWER

• To turnthe airconditionerON, pushthis button.Toturntheair

conditionerOFF,pushthebuttonagain.This buttontakespriorityover

any otherbutton.

Whenyoufirstturn iton,the unitisin coolmode,Highfan speed,

Temperaturesettingat 72°F.

TEMPERATURE SETrlNG

• Usethisbuttontoautomaticallycontrolthetemperatureofthe room.

Thetemperaturecanbe setwithina rangeof60°Fto86°Fby

incrementsof I°F.

FAN SPEED

• Everytime you push this button it advances the setting as follows:

(High ." Low * Med _High)

TIMER

- SHUT-OFF TIME

• You will usually use shut-off time while you sleep.

• With unit running, use Timer to set number of hours until shut-off.

• For your sleeping comfort, once Time is set, the Temperature setting will

raise 2°F after 30 min, and after another 30 min.

• Every time you push Timer button, it advances the Timer setting as follows:

1 Hour , 2 Hours ...... .- 12 Hours maximum.

- START TIME

• With unit not running, use Timer to setnumber of hours before until start.

• Every time you push Timer button, it advances the Timer setting as follows:

1 Hour *2 Hours , ..... ÷ 12Hoursmaximum.

MODE

- Every time you push this button, it will shift among COOL, ENERGY SAVER and FAN.

- ENERGY SAVER

• The fan stops when the compressor stops cooling.

Approximately every 3 minutes the fan will turn on and the unit will check the room air to determine if cooling is

needed.

-15-

INSERTING THE REMOTE CONTROL

BA'n'ERIES

1. Remove the cover from the back of the remote

controller.

2. Insert two batteries.

• Be sure that the (+) and (-) directions are

correct.

• Be sure that both batteries are new.

3. Reattach cover.

FIG. 28

• In order to prevent discharge, remove the batteries

from the remote control if the air conditioner is not

going to be used for an extended period of time

Keep the remote control away from extremely hot

or humid places.

To maintain optimal operation of the remote

control, the remote sensor should not be exposed

to direct sunlight.

• The remote control can be mounted on a wall

using the mountable holder.

FIG. 29

HORIZONTAL AIR-DIRECTION

ADJUSTMENT

• The hodzontal air direction is adjusted by moving

vertical louver.

• The vertical louver control levers are located in the

right and left side of the air discharge.

FIG. 30

VERTICAL AIR-DIRECTION ADJUSTMENT

• The vertical air direction is adjusted by moving the

horizontal louvers.

FIG. 31

-16-

AIR FILTER CLEANING

The Air Filter will become dirty as it removes dust

from the inside air. it should be washed at least

every 2 weeks. If the Air Filter remains full of dust,

the air flow will decrease and the cooling capacity

will be reduced, possiblydamaging the unit.

• Pull the inlet grille forward and pull out the air filter.

(FIG. 32)

• Wash the Air Filter under the faucet with warm

water. Be sure to shake off all the water before

replacing the filter. (FIG. 33)

FIG. 32 FIG. 33

AIR CONDITIONER CLEANING

Clean the front grille and inlet grille by wiping with a

cloth dampened in a mild detergent solution.

The cabinet may be washed with mild soap or

detergent and lukewarm water, then polished with

liquid appliance wax.

To ensure continued peak efficiency, the condenser

coils (outdoor side of the unit) should be checked

pedodically and cleaned if they become clogged

with soot or dirt from the atmosphere. Brush or

vacuum exterior coils to remove debris from fins.

FIG. 34

HOW TO REMOVE THE FRONT

GRILLE

• Open the inlet gdlle.

• Remove the screw securing the Front Grille.

• Push the grille up from the bottom and pull the top

ofthe grille away from the case to lift the top tabs

out oftheir slots.

FIG. 35

HOW TO REPLACE THE

FRONT GRILLE

Attach the front grille to the cabinet by inserting the

tabs on the grille into the slots on the front of the

cabinet. Push the grille in until it snaps into place.

FIG. 36

-17-

BEFORE CALLING FOR SERVICE

Check the following listto be sure a service call is really necessary. A quick reference to this manual may

help you avoid an unneeded service call.

THE AIR CONDITIONER WILL NOT OPERATE

Check if... Then...

Wallplugdisconnected.

Housetuseblownorcircuitbreakertripped.

PowerisOFF.

Unitwastumedoffandthenontooquickly.

TEMPControlsetwarmerthanroomtemperature.

Pushplugfirmlyintowailoutlet.

Replacefusewithfimedelaytypeor reset¢irouilbreaker.

Pushthepowerbutton.

Setunitoffandwait3minutesbeforerestarting.

SetTEMPControltoa lowernumber,

AIR FROM UNIT DOES NOT FEEL COLD ENOUGH.

Check if... Then...

FANSPEEDsetat LOW.

TEMPControls_ toowarm.

Roomtemperaturebelc_v70°F(21°C).

Temperaturesensingtubetouchingevaporatorcoil,

locatedbehindfrontgrille.

PushFANSPEEDbuttontosetatHI.

SetTEMPControltoa lowertemperature

Coolingmaynotoccuruntilroomtemperaturerisesabove70°F(21°C).

StraightentubeawayfTomevaporatorcoil.

THEAIRCONDmONERCOOUNG,BUTROOMISTOOWARM- ICEFORMINGONCOOLINGCOILBEHINDINLETGRILLE.

Check if... Then...

Outdoortemperaturebelow70°F(21°C). Todefrostthecoil,settheMODEtoFAN,FANspeedtoHigh.

Airfiltermaybedirty. Cleanairfilter.RefertoMaintenancesectionofowner'smanual.

Todefrostthecoil,settheMODEtoCool,Fanspeedtohigh,andthe

TEMPControlsettoolow. Tempcont_ toahighertemperature.

THEAIRCONDITIONERC00UNG,BUTROOMISTOOWARM

Check if...

Dirtyairfilter- airrestricted.

TEMPControlsettoowarm.

Frontofunitisblockedbydrapes,blinds,furniture,etc.

Airdistributionisrestricted.

Doors,windows,recjisters,etc.open.Coldairescapes,

Unitrecentlyturnedoninhotroom.

Then...

Cleanairfilter.RefertoMaintenancesectionofowner'smanual.

SetTEMPControltoa lowertemperature

Clearbionkageinfrontof unit,

Close doors, windows, reg_ers, etc.

Allowadditional_mete removestoredheatfromwails,ceiling,floor,andfuture

THE AIR CONDITIONER TURNS ON AND OFF RAPIDLY.

Check if... Then...

Outsidetemperatureisextremelyhot. ISetFANSPEEDonHItobringair coolingcoilsfaster. I

past

NOISE WHEN UNIT IS COOLING.

Check if... Then...

Soeadoffanhitfingwater- fromthemoistureremovalsystem. Thislsnormalwhenhumidityishigh.Closedoors,windows,aedragistera.

Windowvibration- poor nstalaton. Referto nstsiafionnstruclfensorcheckwithnsta er.

WATER DRIPPING INSIDE ROOM WHEN UNIT IS COOLING.

Check if... Then...

I Theairconditionerisirnproperiyinstalled. I Tiltaircondifionerslighltytotheoutsidetoallowwaterdrathage.Referto

nstaaton nstrestionsorsheckwth nsta er.

WATER DRIPPING OUTSIDE WHEN UNIT IS COOLING.

Check if... Then...

Theunitisremovinglargequantitiesofmoisture

fromhumidroom I Thislsn°rmaldudngexceeaivelyhumiddays I

-18-

-19-

|NDICE ...................................................... 20

GARANT|A .............................................. 20

SEGURIDAD ........................................... 21

Instruccionesimportantesde seguridad ...21

REQUISITOS ELECTRICOS ............. 22

INSTALACI(_N ........................................ 23

Requisitos de instalacibn ....................... 23

Instalacibn .............................................. 24

Procedimiento A..................................... 25

Procedimiento B..................................... 26

Procedimiento C..................................... 28

FUNClONAMIENTO ............................. 3O

C6mo y pot qu_...................................... 30

Sonidos normales .................................. 30

Capacidad y tiempode funcionamiento--..30

Caracterfsticas ....................................... 31

Uso del aparato de aire acondicionado.---.31

Caracterfsticas del aparato de aire

acondicionado ........................................ 32

MANTENIMIENTO ................................ 35

Limpieza del filtro de aire ....................... 35

Limpieza del aparato de aire

acondicionado........................................ 35

Cbmo extraer la rejilla frontal ................. 35

Cbmo volver a colocar la rejillafrontal ...35

RESOLUCI(SN DE PROBLEMAS-...36

Antes de Ilamar al servicio t_cnico .........36

ACUERDOS DE PROTECCION

ESPECIALIZADA ..................................39

NUMEROS DE SERVIClO

TF:CNICO .................................. Contraportada

GARANTiACOMPLETADE UNAI_ODEL

APARATODEAIRE ACONDICIONADODE

PARED

DuranteunaSo,a contarapartirdela fechadecompra,cuando

esteaparatodeaireacondic_onadofuncioneparaelenfriamiento

normaldeunahabitacibnyrecibamantenimiento,todoello

segenlasinstruccioaesdeesteManualdelpmpietaFio,Sears

reparar_esteaparatodeaireacondicionado,deformagratuita,si

tuvieraalgundefectodefabricaci6nomateriales.

GARANTfACOMPLETADE CINCOANOSDEL

SISTEMASELLADODE REFRIGERAClON

Durantecincoafiosa contara partirdelafechadecompra,

cuandoesteaparatode aireacondicionadofuncioneparael

enfriamientonormaldeunahabitaci6ny recibamantenimiento,

todoelloseg0nlasinstruccionesdeesteManualdelpropietado,

Searsredarar_iel sistemaselladoderefrigeraci6n(queconsiste

en Ifquidoderefrigeraci6n,tubosdeconexi6nycompresor),de

formagratuita,situvieraalg_ndefectodefabricaci6no

materiales.

ELSERVICIODEGARANTIAPUEDE

CONTACTARSEENELSERVIClODEATENCI()N

AL CLIENTEDESEARS ENEL1-800-4-MY-HOME®.

Lacoberturadeestagarantiaseapricasolamenteaaparatosde

aireacondicionadoutilizedosdeformano comercial,encasas

particulares,

Estagarantiaseaplicas61oduranteelusodeesteproductoen

losEstadosUnidos.

Estagarantfaleconcedederechoslegalesespecificosy puede

queustedtengaotrosderechosadicionalesquevarianseg_nel

estado.

Sears,RoebuckandCo., D/817WA,Hoffman

Estates,IL60179 EE. UU.

- 20 -

Page is loading ...

Kenmore Kenmore 580.74103 Owner's manual

Brand: Kenmore

Model: Kenmore 580.74103

Category: Split-system air conditioners

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

español: Kenmore Kenmore 580.74103 El manual del propietario

Kenmore Kenmore 580.74103 Owner's manual

This manual is also suitable for

Kenmore Kenmore 580.74103 Owner's manual

in other languages

Related papers

Other documents