Shuttle X 5040VA Specification

Brand: Shuttle

Model: X 5040VA

Category: All-in-One workstations

Type: Specification

This manual is also suitable for

X50V4 Series Quick Guide

【

English

】

2. Refastenthestandandthebackcoverwitheightscrews.

 Toplacethemachineonthedeskandtocarryit,dothefollowing:

 PlacetheX50V4onaatsurfacesuchasatable(Picture1),andpullthestand



upwardstoanangleof30°(Picture2).TocarryormoveyourX50V4fullyextend

 theangleto180°(Picture3).

VESAmountingittothewall

Placingonthedesk

Front/Rear/SideView

Runthescreencalibration

programandcorrect4point

locationsonscreenwiththe

panel.

ClickStart/AllPrograms



/eGalaxTouch

/CongureUtility

Select[Tools]tabandclick



[4PointsCalibration]

HowtousetheTouchPanel

 Whenthe4pointscalibrationcompleted,press“OK”tocontinue.

4PointCalibration(CD-ROMdriveinstall)

 X50V4bringsdigitallifeforaneasytouchexperience.Experiencetheeaseof

 managingyourdigitallifewithafewtouchesortheuseofthestyluspen.The

 touchofyourngerreplacesthemouseandisallyouneedtointeractwiththe

 X50V4.

 Touchandholdthecenterofthetarget.

 Repeatonfourcornersandthescreenwilladjustautomatically.

Cleaningthescreen

 Followtheseguidelinesforcleaningtheoutsideandhandlingthescreenofthecomputer:

 Turnothesystemanddisconnectallcables.

 Useadamp,orcleaningcloth,soft,lint-freeclothwithgentlewateronlyandgently



wipethescreensurface.

・Touch=left-clickonthemouse

・Touchandhold=right-clickonthemouse

 Followthesteps(1~3)belowtoconnecttheACadaptertothe“DC-INjack”.

 Pressthe“PowerButton”toturnonthesystem.

Poweringonthesystem

Stand/Handle

Microphone

Webcam

LCDDisplay(SingleTouch)

HardDiskDriveLED

PowerLED

StereoSpeakers

PrinterPort(Optional)

Note:TheX50V4canbemountedtoawallusingaVESAcompatible75x75

mmor100x100mmwall/armbracket.

 IfyouaremountingyourX50V4tothewall,removethecoveronthebackof



theX50V4rst.

 Unscrewfourscrewsofthestandmountandremovethestand.

 TheVESAstandardletsusersmountitontowallseasily.

 Pleaserefertotheuserguideofthewall/armmountkityouboughttoinstallit.

Note:Theproduct’scolourandspecicationsmayvaryfromtheactuallyshippingproduct.

SafetyInformation

ReadthefollowingprecautionsbeforesettingupaShuttleX50V4.

CAUTION

notwalkonthepowercordorallowanythingtorestonit.

CAUTION

Danger

ofexplosionifbatteryisincorrectlyreplaced.Replaceonlywiththesameor

equivalent

typerecommendedbythemanufacturer.

Disposeofusedbatteriesaccordingtothemanufacturer’sinstructions.

Touch

Hold OK

A.BeginInstallation

1. RemovethecoveronthebackoftheX50V4rst,unscrew

 fourscrewsofthestandmountandremovethestand.

Forsafetyreasons,pleaseensurethatthepower

cordisdisconnectedbeforeopeningthecase.

Latch

B.HDDInstallation

1. Unscrewfourscrewsofthebracketandremoveit.

2. MounttheHDDintothebracketwithfourscrews.

1. Replacethebackcover.

D.Complete

2. Unscrewfourscrewsofthebackcoverandremoveit.

3. Replacethecover,complete.

Cover

Screw

4. Carefullypushdownthememorymoduleuntilitsnapsinto

 thelockingmechanism.

BackCover

Screw

Stand/Handle

75 x75 mm

100 x 100mm

181922 20212324

COM1andCOM2Ports(Optional)

VGAPort

Kensington

LockPort 

PowerButton

StylusPen

SDCardReader

USB2.0Ports

Headphone/Line-outJack

MicrophoneJack

HDMIPort

HDMI

USB3.0Ports 

LANPort

USB2.0Ports

DCIn

DC-IN



RJ11DIOPortforCashDrawer(Optional)

COM3,COM4overRJ45(Optional)

Unscrew

1. LocatetheSO-DIMMslotonthemainboard.

3. Gentlyinsertthe



moduleintotheslot



ina45-degreeangle.

SO-DIMMslot

4. InstalltheHDD&bracketinthechassisandtightenthe

 HDD&bracketwithfourscrews.

C.MemoryModuleInstallation

2. Alignthenotchofthe

 memorymodulewith



theoneofthememory

 slot.

45-degree

angle

3. ConnecttheSerialATAandpowercablestotheHDD.

TakeouttheSerialATAandpowercablesfromaccessorybox.

UseDDR3LSO-DIMM

180

3.2.1.

53R-X50V43-H101

Thismainboarddoesonlysupport1.35VDDR3L

memorymodules.

Shuttle X 5040VA Specification

Brand: Shuttle

Model: X 5040VA

Category: All-in-One workstations

Type: Specification

This manual is also suitable for

Download PDF

report

Shuttle X 5040VA Specification

This manual is also suitable for

Shuttle X 5040VA Specification

Related papers

Other documents