Behringer 992 CONTROL VOLTAGES Quick start guide

Brand: Behringer

Model: 992 CONTROL VOLTAGES

Type: Quick start guide

Quick Start Guide

992 CONTROL VOLTAGES

Legendary Analog CV Routing

Module for Eurorack

Controls

(1) CV Switches – Allow the voltage or signal from the

associated input to be sent to the output jacks when the

switch is in the up position. The input is disconnected

when the switch is in the down position.

(2) EXT INPUT – Additional input to be used with the signal-

inverting attenuator circuit.

(3) Attenuator Knob - Turn clockwise to adjust the CV level

from 0 to 10 (unity gain). Turn counterclockwise to invert

the signal from 0 to -10, which is also unity gain. At the

center 0 position, the signal is o (-∞).

(4) CONTROL INPUTS – Connect control voltages from other

modules via 3.5 mm TS cable.

(5) FREQUENCY CONTROL TO LPF – Send the combined

voltage from all 4 inputs to up to 3 modules via

3.5 mm TS cable.

Power Connection

The 992 comes with the required power cable for connecting

to a standard Eurorack power supply system. Follow these

steps to connect power to the module. It is easier to make

these connections before the module has been mounted into

a rack case.

1. Turn the power supply or rack case power o and

disconnect the power cable.

2. Insert the 16-pin connector on the power cable into the

socket on the power supply or rack case. The connector has

a tab that will align with the gap in the socket, so it cannot

be inserted incorrectly. If the power supply does not have

a keyed socket, be sure to orient pin 1 (-12 V) with the red

stripe on the cable.

3. Insert the 10-pin connector into the socket on the back of

the module. The connector has a tab that will align with the

socket for correct orientation.

4. After both ends of the power cable have been securely

attached, you may mount the module in a case and turn on

the power supply.

Installation

The necessary screws are included with the module for mounting

in a Eurorack case. Connect the power cable before mounting.

Depending on the rack case, there may be a series of xed holes

spaced 2 HP apart along the length of the case, or a track that

allows individual threaded plates to slide along the length

of the case. The free-moving threaded plates allow precise

positioning of the module, but each plate should be positioned in

the approximate relation to the mounting holes in your module

before attaching the screws.

Hold the module against the Eurorack rails so that each of the

mounting holes are aligned with a threaded rail or threaded

plate. Attach the screws part way to start, which will allow

small adjustments to the positioning while you get them all

aligned. After the nal position has been established, tighten the

screws down.

(1)

(4)

(5)

(2) (3)

Specications

Signal Connections

Control inputs 3 x 3.5 mm jacks, summed

Impedance 100 kΩ unbalanced

CV range 1 V / octave,

+/-10 V maximum

External input 1 x 3.5 mm jack,

summed with CV inputs

Impedance 100 kΩ unbalanced

Attenuation -∞ to unity gain,

inverting and non inverting

Control outputs 3 x 3.5 mm parallel jacks

Impedance 10 Ω unbalanced

Maximum output level +/-10 V

Controls

Control selectors 4 x sliding routing switches

Attenuator Rotary knob, selectable

Power

Power supply Eurorack

Current draw 10 mA (+12 V),

10 mA (-12 V)

Physical

Dimensions 35 x 40 x 129 mm

(1.4 x 1.6 x 5.1")

Rack units 8 HP

Weight 0.09 kg (0.2 lbs)

LEGAL DISCLAIMER

Music Tribe accepts no liability for any loss which may be suered by any

person who relies either wholly or in part upon any description, photograph,

or statement contained herein. Technical specications, appearances and

other information are subject to change without notice. All trademarks are the

property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake,

Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone

and Coolaudio are trademarks or registered trademarks of Music Tribe

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information

regarding Music Tribe’s Limited Warranty, please see complete details online

at musictribe.com/warranty.

Zhongshan Eurotec Electronics Limited

No. 10 Wanmei Road, South China Modern Chinese Medicine Park,

Nanlang Town, 528451, Zhongshan City, Guangdong Province, China

Behringer 992 CONTROL VOLTAGES Quick start guide

Behringer 992 CONTROL VOLTAGES Quick start guide

Behringer 992 CONTROL VOLTAGES Quick start guide

Related papers

Other documents