Toshiba W-422 Owner's manual

Brand: Toshiba

Model: W-422

Category: Cassette players

Type: Owner's manual

This manual is also suitable for

W-528

TOSHIBA

Hi-FiIV_ SQPB

Video Cassette Recorder

W-528

W-522

W-422

OWNER'S MANUAL

I,_ L'_ ®J_.

I __ -- I

SAFETY PRECAUTIONS

The lightning flash with arrowhead symbol,

within an equilateral tnangler fs intended to

alert the user to the presence of unEnsulated

dangerous voltage"withtn the product's en-

closure that may be of sufftc_ent magnitude

to constitute a nsk of e_ectr_c shock to per-

sons

WARNING

The exclamatton point within an equdatera_

tnangle ts _ntended to alert the user to the

presence of important operattng and mainte-

nance (servicing) instructions tnthe literature

accompanying the apphance

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN

OR MOISTURE DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE

ENCLOSURE. DO NOT OPEN THE CABINET REFER SERVICING TO QUALI-

FlED PERSONNEL ONLY

CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

Product Name V_deo Cassette Recorder

Mode_ Number W-526/W-522/W-422

FCC Notice 'Declaratton of Corformity"

Th_s device complies with part 15 of the FCC Rules Operatton rs subject to the followtng two

condttrons (1) This device may not cause harmful Interference, and (2) th_s device must accept any

interference received, includEng interference that may cause undesired operation

Contact Toshiba America Consumer Products, Inc

Address 1420 Toshiba Dnve, Lebanon, TN 37087

Telephone 615-449-2360

User Installer Caution Changes or modification made to this equipment not expressly approved by

Toshiba Corporation or parttes authorized by Toshiba Corporation could void the user's authority

to operate the equtpment

Note to CATM system installer

This remtnder is provided to call the CATV system installer s attention to Article 820-40 of the NEC

that provtdes gutde_mes for proper groundtng and, _npart=cular, spectfies that the cable ground shall

be connected to the grounding system of the buddrng, as close to the point of cable entry as practica_

It is permissible to record television programs, film, video tapes and other material only

in the event that third party copyrights and other rights are not violated.

In the spaces prowded below, record the Model and Seria_ No _ocated at the rear of your video

cassette recorder

Model No Seria_ No

Retain this informattonfor future reference

IMPORTANT PRECAUTIONS

Save Original Packing Materials /

The original shipping carton and packing materials will come in handy if you ever have to ship

]

your VCR For maximum protection, repack the set as it was originally packed at the factory

Avoid Volatile Liquid

Do not use volatile liquids, such as an insect spray, near the unit

Do not leave rubber or plastic products touching the unit for a long time They will mar the

finish

Moisture Condensation

Never operate this unit immediately after moving itfrom a cold location to a warm location

When the VCR is exposed to such a change in temperature, moisture may condense on the

cylinder inside, one of its most crucial internal parts To prevent the VCR from possible

damage, do not use the unit for at least 2 hours when there is an extreme or sudden change

in temperature

Compatibility

This video cassette recorder (VCR) is compatible with any other VCR bearing the [_

mark HQ VHS equipment is also compatible with existing, non-HQ VHS equipment

As an ENERGYSTAR _' Partner, TOSHIBA has determined that this product or

product model meets the ENERGYSTAR:-guidelines for energy efficiency

IMPORTANT SAFETY

INSTRUCTIONS

CAUTION" PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS

GIVEN IN THIS OWNER'S MANUAL AND THOSE MARKED ON THE UNIT.

RETAIN THIS BOOKLET FOR FUTURE REFERENCE•

This set has been designed and manufactured to assure personal safety Improper use can

result in electric shock or fire hazard The safeguards incorporated in this unit will protect

you if you observe the following procedures for installation, use and servicing This unit is

fully transistorized and does not contain any parts that can be repaired by the user

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO

DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

ONLY.

1. Read owner's manual

After unpacking this product, read the owner s manual carefully, and follow all

the operating and other mstrucbons

-r _ _ , ;._;

I _ _

,[_; _7 , ' I

,_ T • ,

2. Power Sources

ThEsproduct should be operated only from the type of power source indicated ._

on the marking label If you are not sure of [he type of power supply to your I' '] "

home, consult your product dealer or local power company For products / - "__

intended to operate from batter_ power, or other sources refer to the operabng iJ:_ '}_

mstrucbons I L_ ___

3. Grounding or Polarization

ThEsproduct may be equipped w_tha polanzed alternabng current line plug (a

plug hawng one blade wEder[han the other) This plug wdl fit into the power

outlet only one way Thts is a safety feature Ifyou are unable to insert the plug

fullylntotheoutleLtryreverslngtheplug Iftheplugshouldstdlfadtofit contact

your electnc=an [o replace your obsolete outlet Do not defeat the safety

purpose of the polanzed plug

4. Ventdabon

Slots and openings _nthe cabinet are prowded for ventdabon and to ensure

rehable operabon of the product and to protect _tfrom overheating and these

openings must not be blocked or covered The openings should never be

blocked by plactng the product on a bed, sofa, rug or other slmdar surface Thin

product should not be placed in a budt-_nmstallabon such as a bookcase or rack

unless proper venblat_on _sprowded or the manufacturer s _nstrucbons have

been adhered to

,,:,/?-,-,_T-q

5. Heat -

T •

Theproductshouldbesltuatedawayfromheatsourcessuchasradlators, heat r ,_ _ -

registers stoves, or other products (including amphflers} that produce heat

6. WaterandMoisture

Donotusethisproductnearwater-forexample,nearabathtub,washbowl,

kitchensink,orlaundrytub;inawetbasement;ornearaswimmingpooland

thelike.

7. Cleaning

Unplugthisproductfromthewalloutletbeforecleaning.Donotuseliquid

cleanersoraerosolcleaners.Useadampclothforcleaning. ' _-"

8. Power-CordProtection

Power-supplycordsshouldberoutedsothattheyarenotlikelytobewalked_FF'_._-_ ._o_

onorpinchedbyitemsplaceduponoragainstthem,payingparticularattention__ _.. _/_ z

tocordsatplugs,conveniencereceptacles,andthepointwheretheyexit from

the product.

9. Overloading

Do not overload wall outlets; extension cords, or integral convenience recep-

tacles as this can result in a risk of fire or electric shock.

10. Outdoor Antenna Grounding

Ifan outside antenna or cable system isconnected to the product, be sure the antenna or cable system

isgrounded so as to provide some protection against voltage surges and built-up static charges. Article

810 of the National Electrical Code, ANS]/NFPA 70, provides information with regard to proper

grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge

unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

GROUND

CLAMP

D_SCHARGE UNiT

(NEC SECTION 8 _O-20)

$2_98A

POWER SERVICE GROUNDIN G

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC NATIONAL ELECTRICAL CODE

11. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall into such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from touching such power lines or circuits as

contact with them might be fatal.

IMPORTANT SAFETY

INSTRUCTIONS

12 Lightning

For added protection for this product during storm, or when _tis left unattended

and unused for long periods of time, unplug Etfrom the wall outlet and

disconnect the antenna or cable system This will prevent damage to the

product due to hghtnlng and power-line surges

IV' _'

13 Object and L_quld Entry

Never push objects of any kind into th_sproduct through openings as they may • _ -- •_.

touch dangerous voltage points or short-out parts that could lesult tn a fire or F ' 3 -J __-' _ •

electric shock Never sp_ll liquid of any kind on the product _,,L,,___ZS_';_"-_-7P

14 Attachments ' _' • f

Do not use attachments not recommended by the product manufacturer as they may cause hazards

15 Accessories

Do not place th_s product on an unstable cart, stand, tripod, bracket, or table

The product may fall, causing senous injury to a child or adult, and senous

damage to the product Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold wEththe product Any mounhng of

the product should follow the manufacturer s _nstruchons, and should use a

mounhng accessory recommended by the manufacturer

A product and cart combination should be moved with care Quick stops,

excessive force, and uneven surfaces may cause the ploduct and cart

combination to overturn

16 Damage Requ_nng Servece

Unplug th_sproduct from the wall outlet and refer servicing to quahfied service personnel under the

followEng condEhons

a) Wheel the power-supply cord or plug is damaged

b) If hquld has been sp_lled, or objects have fallen Hlto the product

c) If the product has been exposed to rain or water

d) If the product does not operate normally by following the operahng instruchons Adjust only those

controls that are covered by the operahng _nstruchons as an improper adjustment of other controls

may result in damage and wtll often require extensive work by a qualified technician to restole the

product to _tsnormal operahon

e) If the product has been dropped or damaged _nany way

fj When the product exhibits a d_shnct change in performance - thEsHldlcates a need for service

17 Serwclng

Do not attempt to servEce thEsproduct your self as opening or remowng covers

may expose you to dangerous voltage or other hazards Refer all servicing to

quahfled service personnel

18 Replacement Parts

When replacement parts are requEred be sure the serwce technEc_an has used replacement parts

specified by the manufacturer or have the same charactenshcs as the ong_nal part Unauthorized

subshtuhons may result in fire, electric shock, or other hazards

19 Safety Check ___

Upon completion of any service or repairs to this product, ask the service "_- _o

techn_c_antoperformsafetycheckstodetelmH_ethattheproductts_nploper ,_ _ i _ -

operahng condition , L_ _J" •

I I

Contents

INTRODUCTION

Prowdes_mportantnotesand general

explanation ofthe VCR includbng names ofthe

buttons lacks etc

SAFETY PRECAUTIONS .................... 2

IMPORTANT PRECAUTIONS ............. 3

IMPORTANT SAFETY

INSTRUCTIONS ................................... 4

Contents .............................................. 7

Identification of Controls ................... 8

• Front Panel

• Remote Control

• VCR Display

• Rear Panel

PREPARATION

Explains whatyouneedto do beforeoperating

the VCR

How to Use the Remote Control ...... 11

Connections ...................................... 12

Auto Set Up ....................................... 14

Initial Settings Using On-screen

Display ............................................... 15

• Setting the Language

• Optional settings on the SET UP

screen

• Setting the Clock

Storing Channels on the VCR .......... 17

Video Cassette Use .......................... 19

PLAYBACK

Explains vanable functbons concerning

playback

Playback ............................................ 20

• Basic Playback

• Double Speed Playback

• S-VHS Quasi Playback (SQPB)

-t

Variable Speed Playback ................. 21

• Picture Search

• Commercial Movie Skip o

• Still Picture z

• Frame Advance

• Slow-motion Picture

Useful Functions in Tape

Operation ........................................... 23

• Counter Funct=on

• Tape Remaining Time

• Memory Stop Feature

RECORDING

Explains recording functions

Recording a TV Program .................. 25

• Basic Recording

• Watching a TV program while

recording another

• Skipping unnecessary scenes while

recording

• Recording off time setting

Timer Program Recording ............... 26

MTS Broadcast Compatibility .......... 29

ADDITIONAL INFORMATION

Remote Control

for TOSHIBA TVs .............................. 30

Before Calling Service Personnel ... 31

Specifications ................................... 33

Accessories ...................................... 33

Memo .................................................. 34

LIMITED WARRANTY ............. Back cover

INTRODUCTION

Identification of Controls

See the page in E'_ for detabls

This manual shows the names of buttons in italics

I _ _PJliv_vB_Cf

_I-5_POWER Cassettecompartment L25_ REC _19_ EJECT

LINE IN 2 AUDIO

{L/MONO, R} jacks P

LINE IN 2 VIDEO jack L25_CHANNEL

VCR

Display

3-5_ POWER Cassettecompartment _25_ REC _ _ EJECT

II = I I I = II

LINE IN 2 AUDK) VCR D,splay L20_L20_L20_L20_

(L/MONO R) jacks

L25_ REW PLAY FF STOP

CHANNEL

LINE IN 2 VlDEOjack Remote Sensor

Ll-_ POWER Cassettecompartment L25_ REC _1-9_EJECT

Remote Sensor

REW PLAY FF STOP

To operate your TV

To operate this VCR VCR _1

Number buttons

A. SELEC T

(only for model W-528/_V_22 )

PLA Y *

EJECT

REW *

SLOW

DISPLA Y

REMAIN/COUNTER

LSELECT

REC

TV VOL

"rOGHIBA

[15_ POWER

2-0_CH/TRK

L=_JTWVCR

_21_CM SKIP

LISJ1oo

LI-5_ENTER

_20_PLAY*

_2b_ FF*

_2_0_STOP*

_2_1_PAUSE/STILL

]_2-5_ SP/SLP

_23_ COUNT RESET

_2_ _MER

_2_CANCEL

_ PROG.

• These buttons are used to control Ihe

cursor on the screen

Cassette indicator

Timer recording indicator

0-0

VCR

_oo.oo I

HI-FI indicator

(only for model W-528/W-522;

VCR indicator

Multtfuncbonal

tndlcator

LINE OUT AUDIO jacks (L, R)

RF IN (FROM ANT ) terminal

LINE IN 1 AUDIO jacks (L, R)

To wall outlet LINE OUT VIDEO jack

_,__J

LINE IN 1VIDEO jack

CH selector (3/4)

RF OUT (TO TV) terminal

LINE IN 1 AUDIO (Rear), 2 (Front) jacks

If the connected equipment is monaural (has one audio output lack} connect the L (MONO) side the same

sound _s recorded on both L and R on the Hi-Fi track

LINE OUT AUDIO jack

_4 i,_1 _

To wall outlet LINE OUT VIDEO jack

_, J

RF IN (FROM ANT ) terminal

LINE IN AUDIO jack

LINE IN VIDEO jack

CH selector (3/4)

RF OUT (TO TV) terminal

PREPARATION

How to Use the Remote Control

Thrs sectbon explains how to get ready for remote control operation

][ Open the battery compartment lid on the

rear panel

2 Install 2 batteries ('AA" size) following

the polarity diagrams

rll

1;J

-4

3 Close the battery compartment lid

4 Point the remote control at the VCR and press the buttons within the operating range

D_stance wdhm about 7 m from the front of the remote sensor

Angles w_thln about 30 _nevery direction

Notes on batteries

• The Ide of the battenes is about 1 year

depending on the condEtEonsof use

• If the remote control does not operate correctly,

replace all batteries with new ones

• If the remote control is not to be used for a

long period of time, remove the battenes to

avoid possible damage from battery corrosion

Caring for the remote control

• Do not expose the remote sensor of the VCR

to a strong hght source such as direct sunhght

or lUum_natlon (especially h_gh-frequency

hght_ngJwhen using the remote contro_

• Be careful not to spdl water on the remote

control or to place iton anything wet, and avoid

sharp _mpacts

PREPARATION

Conlzection$

Befot'e you use this VCR, it _s necessary to connect it to your TV Several ways of connecting are

avadabledepending on your use of TV or cable box Select one whch is apphcable to your equipment

][ Disconnect the antenna cable from your TV and connect it to the RF IN terminal on the

VCR

2 Connect the RF OUT terminal to the TV_

VHF/UHF _"_'_=

comb,nat,onan,enna _ VnHyFan,enna _ oLHFantenna_*-i_

i i

Model W528_W_522" IFInal ...................................1 .......[.................................

ModelW-422 J "t-- [_L..__ __

Setttng the VCR Output Channel Antenna sphtter

When the VCR is connected Jnthis way the VCR sends the output (not supphed_

signals to channel 3 or 4 on your TV Set Ihe output channel

selector (CH selector) of the VCR to 3 or 4 whichever _svacant

in your" area

W-'_[III] [sT&TJI D]:[e] [_

The AUDIO/VIDEO jacks are also available to connect your TV

MGdel W-52£

W-522 When connected your fV using the

_T _ Mo_el W422 AUDIO/VIDEO OUT jacks

-- To watch vEdeop_ctures set the v_deo tnput mode

o_ = on your TV For the v_deo _nput mode refer to the

LL_ LL_ _nual of your TV

L,r,E ,,T .C,_ -,,L, ,r, D

L,rlE Jr-,,= • _L, ,rl

Choose one of the below according to your usage of the cable box

This set-up will enable you to:

MGdel W-52£

W522 Mode[W 422 -- record an unscrambled channel

_ - watch an unscrambled channel whEle recording _t

- record an unscrambled channel whde watching

__ __ another (only when you connect a cable compahble TV}

,..... gca_LD y_ _You will need to:

_nc_m,n__b_e_ • select TV channel 3 or 4 to receive v{de0 signals

• 1orecord a channel whde watching another press

TV/VCR on the remote control to turn off the VCR'

indicator m the VCR d_splay and select a desFed

channel on the TV #only when you connect a cable-

compahble TV)

Connecdons _on_nued)

Incoming cable

A/B switch

This set-up will enable you to:

- record an unscrambled channel.

- watch an unscrambled channel while recording it.

- record an unscrambled channel while watching

another (scrambled or unscrambled).

You will need to:

• set TV channel to the output channel of the cable

box.

• turn on the cable box and select cable channel 3 ra

or 4 according to the output channel of the VCR. __"

• to record a channel while watching another,

press TV/VCR on the remote control to turn off

the "VCR" indicator in the VCR display and select z

a desired cable channel on the cable box.

This set-up will enable you to:

- watch an unscrambled or scrambled channel

while recording it.

- record any channels through the cable box.

You will need to:

• set TV channel 3 or 4 to receive video signals.

(See page 12).

• set VCR channel to the output channel of the

cable box, and select a desired cable channel

on the cable box.

• whiletheVCRistumedofforthe"VCR"

indicator is not lit in the VCR display, set TV

channel to the output channel of the cable box.

This set-up will enable you to:

- watch an unscrambled or scrambled channel

while recording it.

- record an unscrambled channel while watching

another unscrambled channel (only when you

connect a cable-compatible TV).

• A/B switch "A":record and watch an

unscrambled channel which

comes bypassing the cable

box.

• A/B switch "B": record and watch a scrambled

or unscrambled channel coming

through the cable box.

This set-up will enable you to:

- watch or record a channel through the cable

box via the LINE IN 1 (AUDIO/VIDEO) jacks

for W-528/W-522, LINE IN (AUDIO/VIDEO)

jacks for W422.

You will need to:

• press I.SELECTso that the VCR display

shows °LI" for W-528/W-522,"L" for W-422.

PREPARATION

Auto Set Up

The VCR's clock and tuner channels are set automatically when the VCR _s plugged _nto the AC outlet

V-'_Tt"_1_'t_1111,,i

U_J . H I

L_J L_J LEJ _

_J _LtJG

_OSS'

IL II

'lmlIMll_

1 Plug the VCR into the AC outlet

2 'Auto" blink while the VCR automatically sets the clock using

the data broadcast by the local TV stations

While Auto" is blinking, channel memory is also set

automatically

3 When Auto set up has been completed, the VCR is on

standby mode

Notes

• It may takes several minutes dunng the Auto set-up

• Press CANCEL on the remote control to cancel the auto set-up

PREPARATION

hdtial Settings Usblg On-screen Display

The language selection and clock setting must be set hrst when VCR _sfirst plugged Jnor after Jt

encounters a power failure

Preparation

• Turn on the TV, and select the v_deo channel (3 or 4;, or the v_deo bnput mode _fyou made the AudJoN_deo

connection (page 12)

• Press VCR to set the remote control operating the VCR

_r_

_QQD

lroiNil_

VCR

POWER

REW

pI_ STOP

ENTffR

PROG

][ Press POWERto turn on the VCR

'_ Press PROG.

The following screen appears on the TV

3 Select the language using PLAY or

STOP and press PROG.

The screen turns to the MENU screen

I_ _L_J_

BISLIW,I

MEnU ]

..4

4, Press PROG. to return to the normal TV screen

Optional settings on the SET UP screen

Other optional settings can be made Press ENTERwhde SET UP' is selected on the MENU screen

The screen turns to the SET UP screen

_ _l_J_ i

_ _zB 16B 18B_Page2 3

_ eean i_rtr_Page29'ForW528'W522on'y '

EnD (_]_)l[n6 rnB [$P _ To change the language move down here and set [o the desired one

To exit press PROG. once

ExampleTosettheclockto230pm on

August25(summertime)2002

][ Press PROG.

The MENU screen appears on the TV

2 Select PRESET" using FFor REVI_

and press ENTER

CLOCK S'E[

£H MEMORV

mno_

3 Press ENTERto select "CLOCK SET"

CLOCK SD"

ILSUMMER TIME

n TIME ZOnECH

EnD_

TO |TART OETTInG

4 Select 'AUTO" or' MANU" using PLAY or

STOP

AUTO The VCR automahcaUy sets or

adjusts the clock

If you select AUTO' mode proceed to step 8

MANU You can set the clock manuaUy

If you select MANU" mode, proceed to next

step

Vary the digits to set the hour

PLAY To increase

STOP To decrease

6 Move to the next using FF

(Tomove back press REW)

7 Repeat step 5 and 6 to set the minutes,

month, day, and the year (by the last

two digits)

Proceed to step 10 to start the clock

8 Press ENTERto start the AUTO" clock

set feature

After the VCR Esturned off, _tautomatically

updates the clock using the data broadcast

by the local TV stations

"The clock ts I _a_ _ i

revEsedby

signal at 8 00AMbr°adcasttng I/CLOCKSET l

n SUMMER TIME

TIME ZOnE CO

ii dlnD Juno _ 2

every morning [nD.(_

8CAJlsnlnl3 nOW

9 Select the options using FFor REW

Change the data using PLAYor STOP

1) Set 'SUMMERTIME

(Dayhght-Sawng Time)"

DST start Dayhght-sawng hme begins on

the first Sunday mApnl Because the

clock automatically changes from 2 00 AM

to 3 00 AM (forward one hour)

DST end Dayhght-sawng time ends on

the last Sunday in October The VCR

clock automatically changes from 2 00 AM

to 1 00 AM (back one hour)

remember that any part of a scheduled

Timer Recording that falls between [hese

two times wdl not be recorded

AUTO the VCR is using the clock data

Broadcast by the local TV statEons

IN You want to use the DST function, and

you are leawng in the area that apply

Dayhght-sawng hme

OUT You are not leawng in the area that

apply Dayhght-sawng tEmeand you do no[

want to use DST function

2) Set' TIME ZONE"

If you select AUTO" for your time zone

the VCR sets the clock using the first

CoordEnated UnEversal Time _nformatEon _t

finds If the hme is not correct, select

another [Emezone or use the MANU"

option

3) Set' CLOCK DATA CH"

If you don't know the clock data channel,

select AUTO" The VCR wdl scan

automatically to tune the channel carrying

the clock data

If AUTO CLOCK SET ts unsuccessful set the

tEmeand date through the MANU ' clock

set menu selection

|0 Press PROG.

Now theclockstarts

PREPARATION

Storing Channels on the VCR

This section is required if you receFve only normal TV or unscrambled cable channels

Incoming Antenna/Cable(CATV) Signals

The VCR scans through all receivable TV and CATV channels and stores only the active

ones in your area into the memory Once the stonng {sfinished, you can select a des{red

channel using CH/TRK.

Preparation

• Turn on the TV, and select the v_deo channel {3 or 4) or the v_deo input mode if you made the Audio/Video

connection {page 12)

• Press I SELECTso that the channel number wt}l appear if L1 ! L2 ( For W-528/W-522 only ) or

'L ( For W-422 only) is displayed in the VCR display

ill

1;J

..4

'I1"_,'-_2_ '

-- _

"I_IHIIA

Number

buttons

IO0

REW

PLAE STOP

ENTER

1,6

I SELECT

][ Press PROG to display the MENU screen

2 Select' PRESET" using FFor REW,

and press ENTER

£1ACK SET 1

ca MEMORY

3 Select'CH MEMORY'usng PLAY

or STOP, and press ENTER

Ig ICR1U

lorr on

I-- Ca

EnP.(_

Set TV/CATV to 'TV" or CATV" ustng FFor REW

TM To store channels received via the antenna

CATM. To store channels receEved wa the iricornlng cable

Select'AUTO SCAN" usnng PLAYor I'_ _11_ _11_4_1

STOP, and press FF to set to "ON" EnD

The VCR starts scanning and the

channels are stored m the VCR in .m sc.n z CH o.

ascending order When the scanning is

finished, the screen automahcaUy

returns

6 Press PROG. twice to exit

Adding or erasing channels

Adding channels

Jfa desired channel cannot be scanned

automatically because of a weak signal, it can be

added to the memory.

Erasing channels

You can erase a stored channel from the memory

if it is unnecessary.

1) Follow steps 1 to 3 of "Incoming Antenna/

CATV Signals".

2) Select "ADD CH" or "ERASE CH" using PLAY

or STOP.

To add channels /

_ w clc_ I

_ on I

FCH 1

TO SETCll PUSH11-9KEYS

EnD:_

To erase channels

T. clc_ /

e_eFF on /

_€, /

E:OS..n_ USHe" KE'S 1

3) Enter a channel number of 1 to 125 using

number buttons.

For more than 100 number, first press 100.

For CATV channels, refer to the chart below.

(For other orders, check with your cable

company.)

4) Repeat steps 2) and 3) to add or erase

channels as necessary.

5) Press PROG. two times to exit.

Selecting stored channels

Once the active channels have been stored, you

can select the channels in two ways below.

Number buttons

To enter digits of the channel number.

• For one-digit number, enter O before.

• For more than 100 number, first press 100.

• Each number button needs to be pressed

within 2 seconds.

CH/TRK buttons

To shift up or down the stored channel numbers.

Channel reference chart

Number on the VCR CH NUMBER 1 2 3 4 5 6 7 8 9

TV - 2 3 4 5 6 7 8 9

Corresponding channel number CATV STD (HRC/IRC) 1(A-8) 2 3 4 5(A-7)6(A-6) 7 8 9

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

10 11 12 13 A B C D E F G H I J K L M N O P Q

31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

R S T U V W AA BB CC DD EE FF GG HH II JJ KK LL MM NN OO

52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 "'" 1

52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69

PP QQ RR SS TT UU VV WW XX YY ZZ AAA BBB 65 66 67 68 69 70 71

93 94 95 96 97 98 99 100 101 102 103 .-. 121 122 123 124 125

93 94 A-5 A-4 A-3 A-2 A-1 100 101 102 103 .-. 121 122 123 124 125

CATM signals

• STD (standard) cabJeTV signals

• HRC (Harmonic Related Carriers) cabJeTV signals

• IRC (Incremental Related Carriers) cable TV signals

IRC is also called ICC (Incremental Coherent Carriers)

PREPARATION

Video Cassette Use

Loading a cassette

Push the cassette tnto the cassette compartment with the window side factng up and the

label side towards the front The VCR is automatically turned on The CTO indicator will _,

appear tnthe VCR display

Ejecting a cassette

Press EJECT. The cassette is ejected from the cassette compartment

Warning

Do not insert your hands or any foreign objects intothe compartment This may result

in injuryor damage Take special care with children to avoid accidents

Precautions when using video cassettes

Vtdeo cassettes have a safety tab to prevent accEdental erasure If the tab has already been removed

recordeng cannot be performed

To prevent acctdental erasure

Remove thts safety tab wtth a screwdnver

To record again

Cover the tab hole with adhesive tape

• AvoEdexposing cassettes to dtrect sunhght Keep them away from heaters

AvoEdextreme humEdety,wbratlons or shock strong magnetic f_elds (near a motor transformer or

magnet) and dusty place

PLAYBACK

Playback

This section explabns the basic playback operation

Preparatton

• Select the v_deo channel {3 or 4; or video input mode on the TV

• Press VCR to set the remote control operatmg the VCR

I;]_1l"_i'.ll_i_,_.'F_1

_,QQ

000Q

I'OII4UlIL

][ Load a recorded cassette

Power _s turned on

CH/TRK If the cassette has no safety tab,

playback starts automatlcaUy

2 2 PressPLAYtostartplayback -- ,°Lfill

L FF vcR

3 3 Tostop playback, press STOP - an.mR

REW vc. UU UU

][ Press PLAYdurmg playback

A tape runs at double speed

playback

To resume normal playback Press PLAY

Rewinding / Fast-forwarding

Press REWor FFm the stop mode

Adjusting the tracking

When playback starts, the VCR automatlcaUy adjusts the tracking for dear pictures and sound

{DEgdalAuto Tracking)

If the VCR cannot locate the best possible tracking poent, hold down one of CH/TRKto adjust the

tracking manually

Notes

• During the adjusting the playback p_cture and sound may be dlslorted

• The digital auto tracking _s activated only _n the playback mode

• The no_se on the screen may not be completely ehmlnated depending on the tape used, especially when the

tape was recorded on another VCR

S-VHS Quasi Playback (SQPB)

• This VCR can also play back at tape which _srecorded _n S-VHS format

But the playback pictures does not have the same quahty and resolution as the original S-VHS

playback picture

• This VCR cannot record m S-VHS format

• SQPB is an abbrewat_on for S-VHS Quas_ Playback

Page is loading ...

Toshiba W-422 Owner's manual

Brand: Toshiba

Model: W-422

Category: Cassette players

Type: Owner's manual

This manual is also suitable for

W-528

Download PDF

report

Toshiba W-422 Owner's manual

This manual is also suitable for

Toshiba W-422 Owner's manual

Related papers

Other documents