Pro-Form Fusion 6.0 LX User manual

Brand: Pro-Form

Model: Fusion 6.0 LX

Category: Fitness, gymnastics & weight training

Type: User manual

This manual is also suitable for

PFSY5015.0

Pro-Form Fusion 6.0 LX is a versatile weight system that offers a selection of weight stations designed to develop every major muscle group of the body. Whether your goal is to tone your body, build dramatic muscle size and strength, or improve your cardiovascular system, the weight system will help you to achieve the specific results you want.

Mode!No.PFSY5015.0

SedalNo.

WritetheseriaUnumberinthe

spaceaboveforfuturereference.

SeriaUNumberDecaU(UnderSeat)

Asamanufacturer,wearecom-

mittedto providingcomplete

customersatisfaction,ifyou

havequestions,or ifapartis

damagedormissing,PLEASE

CONTACTOURCUSTOMER

SERVICEDEPARTMENT

DIRECTLY.

CALLTOLL-FREE:

1-888-533-1333

Non.=Fd., 6 a.m.=6 p.m. MST

ON THE WEB:

www.proformservice.com

/ /

Read all precautions and instruc,

tions in this manual before using

this equipment, Save this manual

for future reference.

ourwe#s teat

www.proform°com

new products, prizes,

fitness tips, and much more!

TABLE OF CONTENTS

WARNING DECAL PLACEMENT ............................................................. 2

HMPORTANT PRECAUTHONS ................................................................ 3

BEFORE YOU BEGIN ...................................................................... 4

ASSEMBLY .............................................................................. 5

ADJUSTMENTS .......................................................................... 24

CABLE DHAGRAM ......................................................................... 27

WEHGHT RESHSTANCE CHART .............................................................. 29

EXERCHSE GUHDELHNES .................................................................. 30

ORDERHNG REPLACEMENT PARTS .................................................. Back Cover

LHMHTEDWARRANTY .............................................................. Back Cover

Note: A PART iDENTiFiCATiON CHART and a PART LiST/EXPLODED DRAWING are attached in the center of

this manual Remove the PART HDENTHFHCATHONCHART and PART LHST/EXPLODED DRAWHNG before begin-

ning assembHy,

WARNING DECAL PLACEMENT

The decaJs shown here have been placed on

the weight system, mfa decal is missing or

illegible, please call the toll-free teJephone

number on the front cover of this manual

and order a free replacement decal. Apply

the decaJ in the location shown.

Misuse of this machine may resumtin serious injury.

Read user's manuamprior to use and follow am_warnings

and instructions.

Do not aH_owchiHdren on or around machine.

Keep body, cHothing, and hair free and cHearof amHmoving

parts.

Habelif removed.

hands and

ecs dear of

this area.

PROFORM is a registered trademark of iCON IP, Inc,

iMPORTANT PRECAUTIONS

AWARNmNG: Tored.oethedskofse.ous njury,readthefo,ow ng mportantprecautions

before using the weight system.

Read all instructions in this manual and all

warnings on the weight system before using

the weight system. Use the weight system

only as described in this manual.

that the cables are on the pulleys. Replace aH

cables at least every two years.

It is the responsibility of the owner to ensure

that aH users of the weight system are ade-

quately informed of all precautions.

10. The weight system is designed to support a

maximum user weight of 300 pounds.

11. The weight system is designed to be used

only with the included weight. Do not use the

weight system with dumbbells or any other

3. The weight system is intended for home use type of weight to increase the resistance.

only. Do not use the weight system in any

commercial rental or institutional setting. 12. Always stand on the foot plate when per-

forming an exercise that couJd cause the

4. Keep the weight system indoors, away from weight system to tip.

moisture and dust. Place the weight system

on a level surface, with a mat beneath it to 13. Never release the arms, leg lever, lat bar, leg

protect the floor or carpet. Make sure that press, ab strap_ or handle while weights are

there is enough clearance around the weight raised. The weights will fall with great force.

system to mount, dismount, and use the

weight system. 14. Always disconnect the lat bar from the

weight system when performing an exercise

5. inspect and property tighten aJl parts regular- that does not use the matbar.

ly. Aepiace any worn parts immediately.

6. Keep children under 12 and pets away from

the weight system at aHtimes.

7. Keep bands and feet away from moving parts.

8. Always wear athletic shoes for foot protec-

tion while exercising.

9. Make sure that the cables remain on the puJ°

leys at aJl times, if the cables bind as you are

exercising, stop immediately and make sure

15. Do not use the weight system with the top

weight pinned in an elevated position.

16 Always secure the weight stack with the lock

pin and lock after exercising to prevent

unauthorized use of the weight system (see

LOCKING THE WEIGHT STACK on page 25).

17. if you feel pain or dizziness at any time while

exercising, stop immediateJy and begin cool-

ing down.

A kWAF{NING: Beforebeginningthisoranyexerciseprogram,consultyourphysician.This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read aH instructions before using, iCON assumes no responsibility for personaJ injury or property

damage sustained by or through the use of this product.

BEFORE YOU BEGIN

Thank you for sebcting the versatib PROFORM +_

FUSION 6,0 LX weight system, The weight system

offers a sebction of weight stations designed to deveP

op every major muscle group of the body, Whether

your goal is to tone your body, build dramatic muscb

size and strength, or improve your cardiovascular sys-

tem, the weight system will help you to achieve the

specific results you want,

For your benefit, read this manuaJ carefully before

using the weight system, if you have questions after

reading this manual, see the front cover of this manu-

al, To help us assist you, please note the product

model number and serial number before calling, The

model number is PFSY5015,0, The serial number can

be found on a decal attached to the weight system

(see the front cover of this manual),

To avoid a registration fee for any service needed

under warranty, you must register the weight sys-

tem at www.proformservice.com/registration.

Before reading further, please review the drawing below

and familiarize yourself with the parts that are labeled,

Right Side

Left Side High Pulley

Station

Backrest

Cud Pad

]

Leg Lever

Low Pulley

Station

Foot

Plate

Weight

Note: The terms "right side" and "left side" are determined

relative to a person sitting on the seat; they do not corre-

spond to right and left on the drawings in the manual

Lat Bar

Military Press Arm

Adjustable Backrest

Press Arm

P ress

ASSEMBLED DiMENSiONS:

Height: 80 in, / 203 cm

Width: 80 in, / 203 cm

Depth: 96 in, / 244 cm

Make Assembly Easier for Yourself

Everything in this manual is designed to

ensure that the weight system can be assem-

bled successfully by almost anyone. Before

beginning assembly, make sure to read the

information on this page. This brief intro-

duction will save you much more time than

it takes to read it.

Hire an Authorized Service Technician

To hire an authorized service technician to

assemble the weight system, call toil-free

1-800-445-2480.

Assembly Requires Two Persons

For your convenience and safety, assembb the

weight system with the heUpof another person,

Set Aside Enough Time

Assembling the weight system may require severaU

hours. By deciding to make the task enjoyaMe,

assemMy wHUgo smootHy. You may want to assem-

bb the weight system over a couple of evenings,

SeJect a Location for the Weight System

Because of its weight and size, the weight system

should be assembled in the location where it will be

used, Make sure that there is enough clearance to

walk around the weight system as you assemble it.

Now to Unpack the Box

To make assembly as easy as possible, we have

divided the assembly process into four stages, The

parts needed for each stage are found in individual

bags, Important: Wait until you begin each stage

to open the parts bag for that stage. Place all

parts of the weight system in a cleared area and

remove the packing materials, Do not dispose of the

packing materials until assembly is completed,

The included AHen wrench _ and grease,

and the following toots (not included} may be

required for assembly:

* Two adjustable wrenches

* One standard screwdriver

* One phillips screwdriver

* One rubber mallet

* A small amount of soapy water, and clear tape or

masking tape.

Note: Assembly may be more convenient if you have

a socket set, a set of open-end or closed-end

wrenches, or a set of ratchet wrenches.

Now to identify Parts

To help you identify the small parts used in assembly,

we have included a PART IDENTIFICATION CHART

in the center of this manual. Note: Some parts may

have been pre-attached. If a part is not in the parts

bag, check to see if it has been pre-attached.

Now to Orient Parts

As you assemble the weight system, make sure all

parts are oriented exactly as shown in the drawings,

Tightening Parts

Tighten all parts as you assemble them, unless

instructed to do otherwise,

Questions?

if you have questions after reading the assembly

instructions, see the front cover of this manual.

The Four Stages of the Assembly Process

Frame Assembly--You wiii begin by assembling

the base and the uprights that form the skeleton of

the weight system,

Arm AssembJy--During this stage you wiii assem-

ble the arms and the moving parts.

Cable Assembly--During this stage you wiii attach

the cables and pulleys that connect the arms to the

weights,

Seat Assembly--During the final stage you wiii

assemble the seats, the backrests, and other parts,

Beforebeginningassembly,makesureyou

understandtheinformationin theboxon

sma!l parts, use the PAR]" mDENTmF!CATmON

CHART in the center of this manual

Attach the Foot Hate (90) to the Right Base (1)

with an M10 x 120mm BoUt(97), two M10

Washers (10% and an M10 NyUonLocknut (111),

Do not overtighten the Loeknut; the Foot Plate

must be able to pivot easily.

Unsertfour M10 x 80mm Carriage BoUts(112) up

through the Right Base (1), Hace a piece of tape

over the boutheads to hoUdthe BoUtsin pUace,

Unserttwo M10 x 80mm Carriage BoUts(112) up

through the Left Base (2), Hace a piece of tape

over the boutheads to hoUdthe BoUtsin place,

Attach the Center Base (5) to the Right and Left

Bases (1, 2) with four M10 x 70mm Bolts (57),

four M10 Washers (10% and two M10 Nylon

Locknuts (111), Do not tighten the Bolts yet.

112

109

112

109

4, 4

Attach the Center Upright (9) to the Right and

Left Bases (1,2) with four MIO x 70mm Bolts

(57), four MIO Washers (10% and two MIO

Nylon Locknuts (111), Do not tighten the BoJts

yet,

Attach the Right Upright (7) to the Right Base (1)

with two MIO x 90mm Bolts (102) and two MIO

Nylon Locknuts (111), Do not tighten the

Locknuts yet,

9--

6, 6

Attach the Right Seat Upright (11) to the Right

Base (1) with the indicated MIO x 80mm Carriage

BoUts(112) and two MIO Nybn Locknuts (111),

Attach the CurUPost Upright (10) to the Right

Base (1) with the indicated MIO x 80mm Carriage

BoUts(112) and two MIO Nybn Locknuts (111),

Attach the Left Upright (8) to the Left Base (2)

with two MIO x 90mm BoUts(102) and two MIO

Nybn Locknuts (111). Do not tighten the

Locknuts yet.

lO-¢_/ /

/ /

/ 111 /

111

:_111

9, Attach the Left Seat Upright (14) to the Left Base

(2) with the indicated MIO x 80mm Carriage BoUts

(112) and two MIO NyUonLocknuts (111),

10, Attach the Right Top Frame (3) to the Center

Upright (9) with two MIO x 70mm Bolts (57), two

MIO VVashers (10% and an MIO Nylon Locknut

(111), Do not tighten the Bolts yet.

Attach the Right Top Frame (3) to the Right

Upright (7) with two MIO x 90mm Bolts (102) and

two MIO Nylon Locknuts (111), Do not tighten

the Locknuts yet.

11, Attach the Left Top Frame (4) to the Center

Upright (9) with two MIO x 70mm Bolts (57), two

MIO Washers (109), and an MIO Nylon Locknut

(111), Do not tighten the Bolts yet.

Attach the Left Top Frame (4) to the Left Upright

(8) with two MIO x 90mm Bolts (102) and two

MIO Nylon Locknuts (111), Do not tighten the

Locknuts yet.

12, Attach the Butterfly Frame (24) to the Right Top

Frame (3) with two MIO x 65mm Bolts (110) and

an MIO Nylon Locknut (111), Do not tighten the

Bolts yet.

Attach the Butterfly Frame (24) to the Right

Upright (7) with two MIO x 35mm Screws (113),

Do not tighten the Screws yet.

111 .14

,_ 111

112

111

109

1 111

109

13, Orient a Weight Guide (30) with the indicated

hoUecloser to the bottom, Attach the Weight

Guide to the Center Base (5) with an MIO x

65mm BoUt(110), two MIO Washers (109), a 1/2"

Spacer (68), and an MIO NyUonLocknut (111),

SHde a Weight Bumper (66) onto the Weight

Guide,

Attach the other three Weight Guides (30) to

the Center Base (5) in the same manner.

Tighten the MIO × 70ram Bolts (57) used in

step 3.

14, SHde eUeven Weights (34), with the pin grooves

on the bottom, onto a set of Weight Guides (30),

Orient a Weight Tube (75) as shown, Unsertthe

Weight Tube into the stack of Weights (34),

SHde another Weight (34) onto the set of Weight

Guides (30),

Repeat this step with the other stack of

Weights (34}.

Groove

15, Attach the Center Top Frame (6) to the Right and

Left Top Frames (3, 4) with four M10 x 70mm

BoUts(57), four M10 Washers (109), and two M10

NyUonLocknuts (111), Do not tighten the BoJts

yet.

Attach a Weight Guide (30) inside the Center Top

Frame (6) with an M10 x 65mm BoUt(110), two

M10 Washers (109), a 1/2" Spacer (68), and an

M10 NyUonLocknut (111),

Attach the other three Weight Guides (30} to

the Center Top Frame (6} in the same manner.

Tighten the bolts, screws and [ocknuts used

in steps 4, 5, 8, 10, 11, and 12.

16, AppUygrease to 2" Bushing (63), Attach the Leg

Lever (15) and the 2" Bushing to the CurUPost

Upright (10) with an M10 x 70mm BoUt(57) and

an M10 NyUonLocknut (111),

17, AppUygrease to a 3" Bushing (71) and the two

Large Round Bushings (61) in the Right ButtedUy

Arm (23), Attach the ButtedUy Arm and 3" Bushing

to the Butterfly Frame (24) with an M10 x 100mm

BoUt(85) and an M10 NyUonLocknut (111),

Repeat this step with the Left Butterfly Arm

(22}.

111

_10

61 Grease ,'!!'

// /

/ !J

/ I

/ /

/ i

/ I

_rease

111

18. AppUygrease to the 1 3/4" Bushing (64). Attach

the MHitary Press Frame (20) and the 1 3/4"

Bushing inside the Left Upright (8) with an MIO x

63mm BoUt(104) and an MIO NyUonLocknut

(111).

19. AppUygrease to an MIO x 45mm BoUt(95). Attach

the MHitary Press Arm (21) to the MHitary Press

Frame (20) with the BoUtand an MIO NyUon

Locknut (111). Do not overtighten the Locknut;

the Mititary Press Arm must be able to pivot

easily.

20. AppUygrease to a 2 3/4" Bushing (65). Attach the

Press Frame (13) and the 2 3/4" Bushing to the

Left Base (2) with an MIO x 90mm BoUt(102) and

an MIO NyUonLocknut (111).

21. Attach the Right Press Arm (26) to the Press

Frame (13) with two MIO x 70mm BoUts(57) and

two MIO NyUonLocknuts (111).

Attach the Left Press Arm (25) to the Press

Frame (13} in the same manner.

111

Grease

111

22, Apply grease to an M10 x 70mm Bolt (57), Attach

a Press Arm Handle (27) to the Left Press Arm

(25) with the Bolt and an M10 Nylon Locknut

(111), Do not overtighten the Locknut; the

Press Arm Handle must be able to pivot easily.

Repeat this step with the other Press Arm

Handle (27} and the Right Press Arm (26}.

23, AppUygrease to a 2 3/4" Bushing (65), Attach the

Leg Press (12) and the 2 3/4" Bushing to the Left

Base (2) with an M10 x 95mm BoUt(108) and an

M10 NyUonLocknut (111),

24, Apply grease to an M10 x 75mm Bolt (96), Attach

the Leg Press Hate (29) and a 2 3/4" Bushing

(65) to the Leg Press (12) with the BoUtand an

M10 Nylon Locknut (111), Do not overtighten the

Locknut; the Leg Press Plate must be able to

pivot easily.

25, During steps 25=54, refer to the CABLE DIA-

GRAMS on pages 27 and 28 to identify the

cables and ensure proper cable routing.

Locate the Butterfly Cable (73}. Attach the

CaMe to the Right Upright (7) with an M8 x 25mm

ShouUder BoUt(92) and an M8 NyUonLocknut

(101), Make sure that the Cable end can pivot

easily around the shoutder of the Bolt.

111.

111

26, Wrap the Butterfly CaMe (73) around a Pulley

(43), Attach the Pulley, a CaMe Trap (48), an MIO

Washer (10% and two Finger Guards (45) to the

Left Butterfly Arm (22) with an MIO x 50mm BoUt

(106) and an MIO NyUonLocknut (111), Make

sure that the CabJe Trap is oriented to hold

the Cable in the groove of the Pulley.

27, Wrap the Butterfly CaMe (73) around a Pulley

(43), Attach the Pulley, a CaMe Trap (48), an MIO

Washer (10% and two HaUlFinger Guards (46) to

the Right Upright (7) with an MIO x 120mm BoUt

(97) and an MIO NyUonLocknut (111), Make sure

that the Cable Trap is oriented to hold the

Cable in the groove of the Pulley.

28, Wrap the Butterfly Cable (73) around a Pulley

(43), Attach the Pulley, a CaMe Trap (48), an MIO

Washer (10% and two Finger Guards (45) to the

Right Butterfly Arm (23) with an MIO x 50mm BoUt

(106) and an MIO NyUonLocknut (111), Make

sure that the Cable Trap is oriented to hoJd

the Carte in the groove of the Pulley.

29, Wrap the Butterfly CaMe (73) under the "V"-pulley

(44), Attach the "V"opulley, the Long Cable Trap

(83), an MIO Washer (109), and two Finger

Guards (45) to the Right Upright (7) with an MIO

x 150mm Bolt (94) and an MIO Nylon Locknut

(111), Make sure that the CabJe Trap is orient-

ed to hold the CaMe in the groove of the "V"-

puHeyo

111

,\÷

43.

_111

111_ 45

30, Wrap the Butterfly CaMs (73) over a Pulley (43),

Attach the Pulley to the Right Top Frame (3) with

an MIO x 40mm BoUt(116) and an MIO NyUon

Locknut (111),

Repeat this step with another Puttey (43}.

31, Wrap the Butterfly CabUs (73) under a Pulley (43),

Attach the Pulley, a CaMe Trap (48), and two HaUl

Finger Guards (46) at the second hoUsfrom the

top of the pair of Pulley Hates (49) with an MIO x

50mm BoUt(106) and an MIO NyUonLocknut

(111), Makes sure that the Cable Trap is orient-

ed to hold the Cable in the groove of the

Pulley.

32, Wrap the Butterfly Cable (73) over a Pulley (43),

Attach the Pulley to the Right Top Frame (3) with

an MIO x 45mm BoUt(95) and an MIO NyUon

Locknut (111),

33, Wrap the Butterfly CaMs (73) over a Pulley (43),

Attach the Pulley to the Center Top Frame (6)

with an MIO x 45mm BoUt(95) and an MIO NyUon

Locknut (111),

111

43 73

\ 95

\43

116

106

34. Attach the Butterfly CaMe (73) and a Weight Cap

(67) to the indicated Weight Tube (75) with an

MIO x 50mm BoUt(106) and an MIO NyUon

Locknut (111).

35. Locate the Low CabJe (70). Route the CaMe

through the Leg Lever (15) and the CurUPost

Upright (10).

Attach a Pulley (43) to the Leg Lever (15), over

the Low Cable (70), with an MIO x 45mm Bolt

(95) and an MIO Nylon Locknut (111).

36. Attach a Pulley (43) inside the Curl Post Upright

(10), over the Low Cable (70), with an MIO x

65mm Bolt (110), two MIO Washers (109), two

1/2" Spacers (68), and an MIO Nylon Locknut

(111).

37. Route the Low CaMe (70) through the Right Seat

Upright (11) and the Right Upright (7) and under a

PuUUey(43). Attach the PuUUey,an MIO Washer

(109), and two HaUlFinger Guards (46) to the

Right Base (1) with an MIO x 45mm BoUt(95) and

an MIO NyUonLocknut (111).

,, 73-

106

75-

111

110

109

38, Wrap the Low CaMe (70) over a Pulley (43),

Attach the Pulley, a CaMe Trap (48), and two HaUl

Finger Guards (46) at the bottom hoUeof the pair

of Pulley Hates (49) with an MIO x 50mm BoUt

(106) and an MIO NyUonLocknut (111), Makes

sure that the CabJe Trap is oriented to hold

the Cable in the groove of the Pulley.

39, Attach the Low CaMe (70) inside the Right Base

(1) with an MIO x 65mm BoUt(110), two MIO

Washers (109), and an MIO NyUonLocknut (111),

40, Locate the High Cable (88}. Route the CaMe up

through the Left Top Frame (4) and over a Pulley

(43), Attach the Pulley inside the Top Frame with

an MIO x 65mm BoUt(110), two MIO Washers

(10% two 1/2" Spacers (68), and an MIO NyUon

Locknut (111),

41, Route the High CaMe (88) over a Pulley (43) and

down through the Left Top Frame (4), Attach the

Pulley inside the Top Frame with an MIO x 65mm

BoUt(110), two MIO Washers (109), two 1/2"

Spacers (68), and an MIO NyUonLocknut (111),

42, Wrap the High CaMe (88) under a Pulley (43),

Attach the Pulley, a CaMe Trap (48), an MIO

Washer (10% and two HaUlFinger Guards (46) to

the Small Pulley Plate (50) with an MIO x 50mm

Bolt (106) and an MIO Nylon Locknut (111),

Makes sure that the CabJe Trap is oriented to

hotd the Cabte in the groove of the Pulley.

111 o

1 110

110

109

111

109 109

110 \

43, Route the High CabUe(88) up through the Left

Top Frame (4) and over a Small Pulley (84),

Attach the Pulley inside the Top Frame with an

MIO x 65mm BoUt(110), two MIO Washers (10%

two 1/2" Spacers (68), and an MIO NyUonLocknut

(111),

44, Route the High CaMe (88) over a SmaUUPuUUey

(84) and down through the Left Top Frame (4),

Attach the PuUUeyinside the Top Frame with an

MIO x 65mm BoUt(110), two MIO Washers (10%

two 1/2" Spacers (68), and an MIO NyUonLocknut

(111),

45, Wrap the High CaMe (88) under a PuUUey(43),

Attach the PuUUey,an MIO Washer (109), and two

HaUlFinger Guards (46) to the MiUitaryPress

Frame (20) with an MIO x 45mm BoUt(95) and an

MIO NyUonLocknut (111),

46, Wrap the High CabUe (88) over a PuUUey(43),

Attach the PuUUeyto the Left Top Frame (4) with

an MIO x 45mm BoUt(95) and an MIO NyUon

Locknut (111),

47, Wrap the High CaMe (88) over a PuUUey(43),

Attach the PuUUeyto the Center Top Frame (6)

with an MIO x 45mm Bolt (95) and an MIO Nylon

Locknut (111),

110

109 68

" _84 88

109 68

111

48, Attach the High CaMe (88) and a Weight Cap

(67) to the indicated Weight Tube (75) with an

MIO x 50mm BoUt(106) and an MIO NyUon

Locknut (111),

49, Locate the Press CabJe (72}. Attach the CaMe to

the Left Base (2) with an M8 x 25mm ShouUder

BoUt(92), Make sure that the Cable end can

pivot easily around the shoulder of the Bolt.

50, Wrap the Press CaMe (72) over a Pulley (43),

Attach the Pulley, a CaMe Trap (48), an MIO

Washer (10% and two Finger Guards (45) to the

Leg Press (12) with an MIO x 120mm BoUt(97)

and an MIO NyUonLocknut (111), Make sure that

the CabJe Trap is oriented to hold the Cable in

the groove of the Pulley.

51, Wrap the Press CaMe (72) under a Pulley (43),

Attach the Pulley, a CaMe Trap (48), an MIO

Washer (10% and two Finger Guards (45) to the

Left Seat Upright (14) with an MIO x 120mm BoUt

(97) and an MIO NyUonLocknut (111), Make sure

that the Cable Trap is oriented to hold the

Cable in the groove of the Pulley.

52, Wrap the Press CabUe(72) under a Pulley (43),

Attach the Pulley, a CaMe Trap (48), an MIO

Washer (10% and two HaUlFinger Guards (46) to

the Press Frame (13) with an MIO x 45mm Bolt

(95) and an MIO Nylon Locknut (111), Make sure

that the Cable Trap is oriented to hotd the

Cable in the groove of the Pulley.

48 _'_

111

-67

10(

)9 72

_-12

111

109

46.

53, Wrap the Press CaMe (72) under a Pulley (43),

Attach the Pulley, a CaMe Trap (48), an MIO

Washer (10% and two Haft Finger Guards (46) to

the Left Base (2) with an MIO x 130mm BoUt

(107) and an MIO NyUonLocknut (111), Make

sure that the CabJe Trap is oriented to hold

the Cable in the groove of the Pulley.

54, Attach the Press CaMe (72) to the Small Pulley

Hate (50) with an M6 Washer (114) and an M6

NyUonLocknut (103), See the inset drawing. Do

not completely tighten the Locknut; it should

be tightened so that onJy two threads of the

Cable show past the Locknut.

55, Attach the CurUPad (38) to the CurUPost (16) with

two M6 x 25mm Screws (99),

56, Attach a Backrest (35) to the Right Upright (7)

with four M6 x 25mm Screws (99),

107

Q @

-5O

103

/ /

/ ,

'--s

Page is loading ...

Pro-Form Fusion 6.0 LX User manual

Brand: Pro-Form

Model: Fusion 6.0 LX

Category: Fitness, gymnastics & weight training

Type: User manual

This manual is also suitable for

PFSY5015.0

Download PDF

report

Pro-Form Fusion 6.0 LX User manual

This manual is also suitable for

Pro-Form Fusion 6.0 LX User manual

Related papers

Other documents