OWNER’S MANUAL
© 2018 Miller Electric Mfg. LLC
FORM: OM-235937H 2018−02
All Purpose Running Gear For Gas Or Diesel Welder/Generator 300477
1. Safety Symbol Definitions
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
DANGER ! - Indique une situation dangereuse qui, si elle
n’est pas évitée, entraînera la mort ou des blessures
graves. Les éventuels risques sont représentés par les
symboles joints ou expliqués dans le texte.
Fsafe1 2013-10
Beware of electric shock from wiring. Stop engine and
disconnect negative (−) cable from battery before install-
ing this kit. Reinstall all panels and covers.
Attention aux chocs électriques des câbles. Arrêter le
moteur et débrancher le câble négatif de la batterie avant
d’installer cet ensemble. Réinstaller tous les panneaux et
couvercles.
Engsafe1 2013-10
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Indique une situation dangereuse qui, si elle n’est pas
évitée, entraînera la mort ou des blessures graves. Les
éventuels risques sont représentés par les symboles
joints ou expliqués dans le texte.
Fsafe2 2013-10
Falling equipment can injure, and damage equipment.
Never put any body part under unit while lifting. Lifting
forks must extend out opposite side of base. Lift and sup-
port unit only with proper equipment and correct proced-
ures. Follow the guidelines in the Applications Manual for
the Revised NIOSH Lifting Equation (Publication No.
94−110) when manually lifting heavy parts or equipment.
La chute de l’équipement peut provoquer des blessures
ou des dommages matériels. Ne jamais mettre une partie
du corps sous l’appareil pendant le levage. Les fourches
de levage doivent ressortir du côté opposé de la base. Ne
soulever l’appareil qu’avec un équipement en bon état
selon les procédures correctes. Suivre les consignes du
Manuel des applications pour l’équation de levage NIOSH
révisée (publication Nº 94–110) lors du levage manuel de
pièces ou équipements lourds.
Fsafe19 2013-10
NOTICE
AVIS
Indicates statements not related to personal injury.
Signale des consignes non associées aux dommages
corporels.
Indicates special instructions.
Fournit des instructions spéciales.
Fsafe3 2013-10
Wear safety glasses with side shields.
Porter des lunettes de sécurité avec écrans latéraux.
Fsafe8 2013-10
CALIFORNIA PROPOSITION 65 WARNINGS
WARNING: Cancer and Reproductive Harm − www.P65Warnings.ca.gov
PROPOSITION CALIFORIENNE 65 AVERTISSEMENTS
AVERTISSEMENT : cancer et troubles de la reproduction − www.P65Warnings.ca.gov.
Fsafe26 2018-01
2. Tools Needed
3/8, 9/16 in.
7/16, 9/16 in.
OM-235937 Page 2
Ref: 805 075-A
. Remove paint from axle grooves be-
fore installing retaining rings.
Assembly
Remove and discard existing hardware
from handle attachment points.
Assemble casters to caster mounting
bracket.
Assemble base rails, axle, and wheels
(valve stems out).
Install onto unit using mounting hole 3 in
rails. Use other holes to adjust balance.
Install caster mounting bracket onto base
rails.
Install handle and leave loose. Install
crossmember and tighten all hardware.
Grease wheels through fittings.
NOTICE − Never Flat tires have a reduced
load rating. The tire set is sized to support
the unit, fuel, and weld cables only. Addi-
tional weight will damage the tires.
Description (Qty)
Part
No.
Item
No.
1 235793 Caster, Swvl 8.00 In Rubber X 2.000 In Wide (2)
2 235791 Bracket, Mtg Caster (1)
3 601965 Screw, 375−16x1.00 Hex Hd−pln Gr5 Pld (12)
4 167788 Nut, 375−16 .56hex .34h Stl Pld Sem Cone Wshr.88d (12)
5 240862 Rail, Base Support Rh (1)
6 240861 Rail, Base Support Lh (1)
7 252981 Axle, Wheel 1in Dia X 30.487 Lg (1)
8 237725 Wheel, Rbr Never Flat 14.5 Od X 4.75 Wide X 1” Bore (2)
9 602251 Washer, Flat 1.062 Id X 2.0 Od X .134T Stl Pld ANSI 1.00 (2)
10 145665 Ring, Rtng Ext 1.000 Shaft X .085 Thk E Style Pld (2)
11 602159 Screw, 312−18x .75 Hex.66d Stl Pld Slffmg Tap (4)
12 220263 Assy, Handle Running Gear (1)
13 604224 Screw, 250−20x .75 Hexwhd.50d Stl Pld Slffmg Tap (6)
14 220375 Bracket, Crossmember (1)
15 108940 Screw, 250−20x .75 Hexwhd.61d Gr5 Pld (2)
16 152461 Nut, 250−20 .44hex .23h Stl Pld Sem Cone Wshr.65d (2)
Be sure to provide model when ordering replacement parts.
⇓
12
15
14
13
3
5
4
7
8
10
11
2
1
3
4
6
13
16
9
3. Assembling All Purpose Running Gear 300477
Handle attachment points
-
1
-
2
Miller RUNNING GEAR PROTECTIVE CAGE Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Miller PROHEAT SERIES ADAPTOR (195 437) Owner's manual
-
-
Miller RUNNING GEAR, BOBCAT 200 AIR PAK (301460) Owner's manual
-
-
-
-
-
-
-