Quick Reference 931350A © 2017, CyberData Corporation, ALL RIGHTS RESERVED© 2017, CyberData Corporation, ALL RIGHTS RESERVED 931350A Quick Reference
Getting Started
Take the following into consideration before you install this product:
• Due to the size and mass of this product, it is important that the Backbox is safely installed according to these installation
instructions.
• Make sure that the type of wall is capable of supporting the system and use screws that are suitable for that type of wall.
• The system must be installed by qualified personnel in accordance with state and local building regulations.
• Also see the Install the DX70 Phone to Enclosure (on the other page).
• Locate the provided Security Torx Driver Bit (usually taped right next to the Hookswitch on the Faceplate).
• Tool required to remove Security Torx Screws (an Electric Hand Drill or Powered Screwdriver)
• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
• WARNING: This enclosure is not rated for any AC voltages!
Hookswitch Wires to USB to Analog Audio Module Connections
Contacting CyberData
Black Wire
USB - B Plug
on DX80
USB - A to B Cable
1
2
3
4
6
7
8
Plug in to Connector Panel
Plug in to (J1)
USB - A Plug
J4
J1
Red Wire
FACTORY DISCONNECTED
RECONNECT BEFORE FASTEN
FACEPLATE TO BACKBOX
***
ASSEMBLY
HOOKSWITCH
Red Wire to J4 (Position 5)
Black Wire to J4 (Position 9)
5
9
& WIRES TO SOCKET
SOCKET
PLUG
FACTORY PRE-INSTALLED
WIRES TO PLUG
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: [email protected]
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
Backbox Mounting Holes Dimensions
Install a Shunt on JP2 to Enable Auto Answer Mode
Tool Required:
1) Hammer
2) Blade Screwdriver
One Inch Conduit
EMT Fitting
Knock Out
Conduit Hole Fits
(One on Each Side)
Knock Out
Knock Out Knock Out
Rear
Right Side
Front
Top
Bottom
Left SideRight Side
Rear
Front
Top
Rear
Rear
Bottom
Front
Front
Left Side
Rear
17.72 [450.0]
13.39 [340.0]
14.17 [360.0]
19.69 [500.0]
Ø1.16 [Ø29.5]
Hole Diameter
Typical EMT Fitting
2
1
1) Dimensions are in Inches [Millimeter]
Notes:
2) 1" EMT Fitting is not provided.
3
1.27 [32.2]
6.50 [165.0]
2.00 [50.8]
2.02 [51.2]
View Shown with
Hole Plug Installed.
Open Faceplate
then Remove Nut
from the Inside
2.36 [60.0]
2.02 [51.2]
2.00 [50.8]
2.00 [50.8]
2.02 [51.2]
2.36 [60.0]
2.02 [51.2]
2.00 [50.8]
6.50 [165.0]
4) Dimensions are in Inches [Millimeter]
1) 11/32" or 9mm Box Socket / Wrenches
Tool Required to Remove Hole Plug:
ø0.41 [ø10.5]
ø0.63 [ø16.0]
ø0.41 [ø10.5]
ø1.30 [ø33.0]
JP2
Shunt
The IP Endpoint Company
Installation Quick Reference
DX70 Secure Phone
011388
© 2017, CyberData Corporation, ALL RIGHTS RESERVED 931350A Quick Reference Quick Reference 931350A © 2017, CyberData Corporation, ALL RIGHTS RESERVED
Install the DX70 Phone to Enclosure
6" Wire Tie (2x)
Wire Tie Mounting
1.5" Square
Base (2x)
Power Supply
Power Plug
Place
Here
USB-A Plug
DX70
(Customer Provided)
DX70
(Customer Provided)
Audio Module
KO
KO
KO
KO
Turn to Open Lens Cover
USB to Analog
1) 11/32" or 9mm Open Wrench or
Tool Required to Remove Hole Plug:
Power Cord
to AC Outlet
Power Cord
to Phone
Plexiglass Cleaning Instruction:
Plexiglass Cleaner to Wipe Surface Clean
1) Use Clean Damp Cloth to Wipe Surface Clean
Screen Cleaning Instruction:
Use Provided Security Torx
USB to Analog Audio Module Diagram
See Hookswitch to
for Details Connections
Driver Bit to Fasten Screws
to Backbox
Tool Required:
Electric Hand Drill or
Powered Screwdriver
Use provided cable management kit
#00 size Phillips Screw Driver
Jumper Shunt
Accessory Kits in Ziploc Type Bag
to bundle up cables
Phone Mounting Instruction:
2) Screw Driver
1) Hammer
Tool Required to Remove Knock Outs (KO):
3) Plier
1/4" Self-Tapping Screw
Up to 1/4" Square Neck Carriage Bolt
Knock Outs (KO) & Keyhole Fit:
or 10 Millimeter Machine Screw
Box Socket & Wrench
To Remove Phone from Backbox:
Spare Screw
T-15H Hex Bit
RECEIVER
RECEIVER
Label
Connections
RECEIVER
LEVER
J4
PIN
PIN
Both Sides before Fasten
Faceplate to Backbox
RECEIVER
Use a Paper Clip Through Hole
to Access Power Button
Mic
Hole
5) Re-install Mounting Screw to Secure LEVER.
1) Unsnap to Remove Both Panels on Back of Phone.
3) Temporary Place Phone (Foot Stand Hinges) on to RECEIVERs.
4) Lift LEVER Up to Engage Locking Mechanism (on PINs).
2) Remove Mounting Screw from LEVER,
1
2
then Pull LEVER Down.
Foot Stand
Foot Stand
Here
Foot Stand
Here
1) Remove Mounting Screw from LEVER.
3) Use Left Hand Reach Down and Lift the Foot Stand Upward
with Right Hand Holding the Upper Corner of the Phone
2) Pull LEVER Down to Disengage Locking Mechanism.
then Gently Remove Phone from Backbox.
Foot Stand Hinges
Be Careful Not to Pull Phone Out Too Fast!
Cables Are Still Connected to Phone!
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
CyberData 011388 Owner's manual
-
-
-
-
CyberData 011426 Owner's manual
-
-
-
-
-