Tripp Lite EnviroSense2 Owner's manual

Brand: Tripp Lite

Model: EnviroSense2

Type: Owner's manual

This manual is also suitable for

E2SLD9

Owner’s Manual

EnviroSense2

Leak Detection Sensor

Model: E2SLD

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

You could also win an ISOBAR6ULTRA surge protector—a $100 value!

www.tripplite.com/warranty

1 Introduction 2

1-1 Parts List 2

1-2 Tools Required 2

1-3 Speciﬁcations 2

2 Important Safety Instructions 2

3 E2SLD Installation 3

3-1 Mounting the Leak Detection Sensor 3

3-2 Wiring the Sensor 3

4 Connecting to WEBCARDLX and E2MTHDI 4

5 Warranty and Product Registration 4

Español 5

Français 9

Русский 13

1-1 Parts List

Water Sensor

Cover

22 AWG Cable, 15 ft. (4.6 m)

Owner’s Manual

Double-Sided Adhesive Tape

1-2 Tools Required

Wire Cutters

Wire Strippers

Phillips Screwdriver

Flathead Screwdriver

1-3 Speciﬁcations

Electrical

Voltage: 5~24V DC

Standby Current: 1 mA

Alarm Current: 200 mA

Contact Closure Type: Normally Open

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation and operation of the products

described in this manual. Read all instructions and warnings thoroughly before attempting installation. Failure to comply may

invalidate the warranty and cause property damage and/or personal injury.

1 – Introduction

2 – Important Safety Instructions

The E2SLD leak detection sensor is designed to detect water leakage or leakage of any electrically conductive ﬂuid. The E2SLD supports a

Normally Open contact closure connection. It must be used with a compatible Tripp Lite UPS or PDU equipped with the WEBCARDLX or

LX Platform interface, along with a compatible E2 environmental sensor module (both are sold separately).

• Install in a controlled indoor environment, away from moisture, temperature extremes, ﬂammable liquids and gasses, conductive contami-

nants, dust and direct sunlight.

• Provide suitable grounding in accordance with all applicable electrical wiring regulations.

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life

support equipment or to signiﬁcantly affect its safety or effectiveness is not recommended.

A B C D

3 – E2SLD Installation

The E2SLD leak detection sensor should be mounted on a raised ﬂoor near cooling units and other applications where water and other

electrically conductive ﬂuid leakage detection can occur.

Approximately 1” (25 mm)

Approximately 0.38” (10 mm)

3-1 Mounting the Leak Detection Sensor

The E2SLD supports mounting by screws, double-sided tape, or adhesive.

Mark the intended location of the E2SLD with the probes facing

downward approximately 1/8” (3 mm) above the ﬂoor.

Mount the sensor to a wood, metal, or concrete* surface using the

provided #6 screws or double-sided tape.

*A user-supplied adhesive will be necessary for concrete surface mounting.

3-2 Wiring the Sensor

Before attaching the wire to the switch, use wire cutters to clip to

desired length (if necessary).

Use wire strippers to cut back the covering of the two wires and

remove a small amount of insulation from the end of each wire

(do not cut through the insulation into the wire itself).

Correct polarity is required. Twist the tinned or bare ends of

each wire and place the red wire on the “+” positive marked

terminal and the black wire on the “-” negative marked terminal.

Wrap them clockwise under the head of each screw on the

sensor. Tighten the screw by turning it clockwise.

Use cable ties and adhesive cable tie holders (user-provided) to

secure the entire length of the wire.

Route the wire away from the sensor and attach the other ends

to one of the input connections on the compatible E2MTHDI

module, noting the polarity markings that were wired at the

sensor.*

*Each E2MTHDI input contacts will have “+” positive polarity markings to

ensure proper wiring connection.

FLOOR

1/8” (3 mm)

The E2SLD is for use with Tripp Lite’s WEBCARDLX and compatible EnviroSense2 (E2) E2MTHDI sensor modules. Tripp Lite UPS systems

and PDUs using the LX Platform connect to an Ethernet network for remote monitoring, control (select models), and environmental condition

reporting via the web, SNMP, telnet or SSH management interfaces.

The E2MTHDI environmental sensor module supports up to two contact closure connections per module. Up to three E2 modules can be daisy

chained together to support a combination of temperature, humidity and contact monitoring.

For more information about WEBCARDLX and EnviroSense2 (E2) sensor modules, refer to their Owner’s Manuals, available for download at

www.tripplite.com/support.

Limited Warranty

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 5 years from the date of

initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES

OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES

OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND

CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you speciﬁc legal rights, and you may have other rights which vary from

jurisdiction to jurisdiction.)

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject

to great variation, the manufacturer makes no representation or warranty as to the suitability or ﬁtness of these devices for any speciﬁc application.

Product Registration

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from

Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country)

• Send the new equipment back for recycling when this ultimately becomes waste

Tripp Lite has a policy of continuous improvement. Speciﬁcations are subject to change without notice.

4 – Connecting to WEBCARDLX and E2MTHDI

5 – Warranty and Product Registration

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support