Page is loading ...
Dive Rated Hard
Waterproof Case
User Guide
IDENTIFICATION OF PARTS
1 Power ON/OFF
2 Shutter Button
3 Video Button
4 Zoom Narrow
5 Zoom Button
6 F Button
7 Mode Button
8 DISP Button
Polaroid and Polaroid & Pixel are trademarks of PLR IP Holdings, LLC, used under license. All other
trademarks are the property of the respective owner, who has not sponsored, endorsed or approved
this product. PLR IP Holdings, LLC does not manufacture this product or provide any Manufacturer’s
Warranty or support.
For warranty information and technical support please call
1-800-226-6534 or visit www.polaroid.com
Questions?
Need some help?
These instructions will help you
enjoy your new product
If you still have questions
call our support line:
1-800-226-6534
or visit us at
www.polaroid.com
Distributed by:
C&A Licensing LLC
2 Bergen Turnpike
Ridgefield Park, NJ 07660
© 2012 All Rights Reserved
MADE IN CHINA
Product features, specifications and appearances
are subject to change without notice.
Safety Precautions
It is very important to read through the following safety
precautions before using your waterproof camera case
in order to guarantee human safety and to avoid
product damage.
1 In the event water leakage is observed while using the
camera case, immediately stop using it and remove it
from the water. Failure to do so may cause an electrical or
fire hazard. Use a soft, clean cloth to remove any water
from the interior of the camera case. Before returning the
case to the water, follow the directions under the title
INSPECTING THE WATER SEAL contained within the
heading titled Caring for Your Waterproof Case and
Your Camera.
2 Remove your camera from the waterproof camera case if
it is not to be used for an extended length of time.
3 Avoid leaving the waterproof camera case in strong
sunlight, near heat or fire. Doing so may cause the camera
case to deform and thereby create a water leakage.
4 Do not use the waterproof camera case in hot water (in
excess of 100°F).
5 Do not use the neck strap when you are diving with the
waterproof camera case. It may become entangled and
cause strangulation or other mishaps.
6 Do not use the waterproof camera case at depths
exceeding 131 feet.
7 Do not attempt to make any alteration to the camera case
as it may affect its waterproof performance.
8 Do not apply excessive force to the camera case body or
its buttons.
9 Inspect the water seal O-ring before using the waterproof
camera case. (See the section titled INSPECTING THE
WATER SEAL.)
10 Do not throw or drop the waterproof camera case.
11 Do not use any water sealing compound on the O-ring
other than the one that comes with the waterproof camera
case; failure to do so may adversely affect its water sealing
performance. If this happens, wipe it off and apply the
water sealing compound that was provided in the package.
12 Avoid inserting or removing your camera in hot or wet
locations.
13 Avoid using the waterproof camera case in a high
temperature environment for too long a period of time.
14 In the event of a large difference between air temperature
and water temperature, water droplets (condensation) may
occur inside the camera case, and the water may damage
the camera. If condensation is discovered, remove the
camera case from the water and clean the inside of it with
a soft, clean cloth before putting it back to use.
TESTING THE WATERPROOF CASE
Before using the Polar oid waterproof case, verify that it is
indeed waterproof.
1 Check that the O-ring is free of dirt or sand particles. Then,
close the case without a camera in it.
2 Dip the case in at least eight inches of clear water for at
least five minutes to ensure there are no leaks.
3 Repeat step two with your camera enclosed in the case.
Check for leaks.
4 If a water leak is observed, remove the camera from the
case and follow the directions the title INSPECTING THE
WATER SEAL contained within the heading titled Caring
for Your Waterproof Case and Your Camera. If the problem
still exists, contact the retailer from which it was purchased.
9 AE/FE Button
10 Auto Func
11 Play Button
12 Multiple Choice
13 FUNC/SET Button
14 Menu Button
15 Flash
16 Stand Hole
17 Safety Lock
18 String Hole
NOTE: The buttons and
adjustment wheels listed
above will operate a designated
camera control. Refer to your
camera’s instruction manual for
the function of each.
6
9
8
10
13
18 16 14 15
17
11
12
16
1 2 3 4 5
Warranty Card
Limited Warranty: C&A Licensing LLC (”C&A”) warrants this product to the original consumer only and is not
transferable. This warranty covers products that fail to function properly UNDER NORMAL USAGE, due to
defects in material or workmanship. Your product will be repaired or replaced at no charge for parts or labor for a
period as outlined below (the “Warranty Period”) from your date of purchase. You will be responsible for shipping
the product to C&A or its authorized servicer for warranty support.
Warranty Period
1 year limited warranty: NON-CARBON FIBER TRIPODS, CARD READERS, CASES, CLEANING ACCESSORIES,
TRIGGER REMOTES, CORDS, FLASH UNITS, LED LIGHTS, BATTERY GRIPS, REPLACEMENT BATTERIES, LENS
EXTENSION TUBES, WATERPROOF ACCESSORIES
5 year limited warranty: CARBON FIBER TRIPODS, ALL TERRAIN TRIPOD, LENS CAP, WHITE BALANCE CAPS,
CAMERA FILTERS AND LENSES
What is Not Covered by Warranty
All other situations, including but not limited to damages or malfunctions not resulting from defects in material or
workmanship and damages or malfunctions from other than normal use, including but not limited to, repair by
unauthorized parties, tampering, modification or accident.
What To Do When Service Is Required
When returning your defective product (postage pre-paid) for service, your package should include:
1. Copy of original bill of sale
2. A detailed written description of the problem
3. Your return address and telephone number (Daytime)
4. The defective product
5. Mail to: C&A Licensing LLC, 2 Bergen Turnpike, Ridgefield Park, NJ 07660
-You may also visit www.polaroid.com for further assistance if necessary or call our technical support
department toll free at 1-800-226-6534
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE EXPRESSLY DESCRIBED ABOVE, AND
NO WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL
APPLY AFTER THE EXPRESS WARRANTY PERIOD STATED ABOVE, AND NO OTHER EXPRESS
WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR ENTITY WITH RESPECT TO THE
PRODUCT SHALL BE BINDING ON C&A. THIS WARRANTY IS THE EXCLUSIVE WARRANTY WITH
RESPECT TO THE PRODUCT AND C&A IS THE EXCLUSIVE WARRANTY PROVIDER FOR THE
PRODUCT. REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY OF THE CONSUMER. IN NO
EVENT WILL C&A, ITS MANUFACTURERS, DISTRIBUTORS OR PLR IP HOLDINGS, LLC BE LIABLE FOR
ANY INCIDENTAL, DIRECT, INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES (SUCH
AS, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF PROFITS, BUSINESS, SAVINGS, DATA OR
RECORDS) RELATED TO THIS PRODUCT. EXCEPT AS STATED HEREIN, NO OTHER WARRANTIES
SHALL APPLY. NOTWITHSTANDING THE FOREGOING, CONSUMER’S RECOVERY AGAINST C&A
SHALL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT SOLD BY C&A. THIS WARRANTY
SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL CONSUMER WHO PURCHASED THE
PRODUCT AND IS NOT TRANSFERABLE.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow
limitations on warranties, so the above limitations or exclusions may not apply to you. This Warranty
gives you specific rights, and you may have other rights, which vary from state to state.
SPECIFICATIONS*
Dimensions
Weight
6.7” x 5.4” x 5.25”
22.2 oz
Material
Maximum
Water Depth
Polycaronate, ABS Plastic,
Clear Plate Glass,
Stainless Steel, EPDM
Rubber
131-ft (40 meters)
*Specifications subject to change without notice
Caring for Your Waterproof Case and
Your Camera
Please be sure to read through the following safety
precautions before using your Polaroid waterproof
camera case.
INSPECTING THE WATER SEAL
1 Before using the case with your camera, inspect the O-ring.
2 Check to be certain that there is no dirt or foreign particle
either on the O-ring or in the groove of its mating surface
on the front cover. Look for such things as sand or dirt
particles, hair, small bits of metal or paper.
3 Inspect the O-ring for nicks or cuts.
4 Be sure the O-ring hasn’t been flattened or deformed in
any way.
5 If you have reason to remove the O-ring, follow the
instructions in the next section, REMOVING THE 0-RING.
REMOVING THE O-RING
1 Follow the O-ring grove around to the middle of the hinged
side of the rear case. A cut out has been provided to allow
easier and safer removal of the O-ring.
2 Remove the O-ring at the cut out with your fingers or a
blunt instrument such as a toothpick.
3 Do not stretch the O-ring. Stretching will cause the O-ring
to leave gaps for water leakage.
4 Clean the O-ring by flushing it with fresh water and gently
remove dirt using your fingers.
5 Apply one drop of water sealing grease that came with the
Polaroid waterproof camera case and wipe it along the
entire length of the O-ring using two fingers pulling from
one direction until the circumference of the O-ring has
been covered. The sealing compound must evenly cover
the O-ring. Do not overstretch the O-ring while applying
the grease.
Note: Use only your clean fingers to apply the grease.
Using paper, a cloth or similar material will not coat the
O-ring evenly.
6 Applying too much water sealing compound may cause
water leakage.
7 Carefully return the O-ring to its groove on the rear cover.
8 It is a good idea to remove, clean and lubricate the O-ring
on a regular basis to ensure that the camera case retains
its leak-proof performance.
9 It is recommended that the O-ring be replaced once a year
regardless of its condition.
CONTENTS
(1) Waterproof Camera Case
(1) O-Ring
(1) Neck Strap
(1) Wrist Strap
(1) User Manual
(1) Water Sealing/Lubricating Grease
AFTER USE MAINTENANCE
1 After using the waterproof case for underwater
photography or out in the rain or snow, the exterior of the
case should be wiped dry with a clean, soft cloth.
2 Remove your camera from the case.
3 Close and lock the empty case .
4 Now use plenty of fresh, clean water to rinse the case
thoroughly. Water should not exceed 100°F; hotter water
may damage the case.
5 If the camera case was used in sea water, a longer
cleaning time is required. Allow the case to soak for a
few hours before wiping it dry. Be sure the entire case
remains submerged.
6 To eliminate the possibility of scratching the case, be sure
there are no particles of sand or dirt on the case or on the
cleaning cloth when wiping the case.
7 Open the case and clean the interior by gently wiping all
surfaces with a clean, dry cloth.
/