Directed Electronics 21994 Owner's manual

Model 21994

Owner’s/Installation Guide

Bitwriter®, Code Hopping™, Doubleguard®, ESP™, FailSafe®,

Ghost Switch™, Learn Routine™, Nite-Lite®, Nuisance

Prevention® Circuitry, Revenger®, Silent Mode™, Soft Chirp®,

Stinger®, Valet®, Vehicle Recovery System®, VRS®, and

Warn Away® are all Trademarks or Registered Trademarks of

Directed Electronics.

iii

Congratulations

Congratulations and thank you for purchasing one of our state-of-

the-art keyless entry systems. Directed is the world leader in vehicle

security, remote start, and keyless entry systems, so yes, you have

made the right choice!

STOP! Read this First

Please make sure you follow all the steps listed below

before attempting to install this system in your vehicle.

Step 1: Read this guide from cover to cover. You can view the a

Do-It-Yourself installation video online at www.readyremote.com.

Step 2: Register at www.readyremote.com to gain access

to our vehicle database. This provides you with the speciﬁc in-

stallation information for your vehicle and identiﬁes any addi-

tional hardware, if needed, to support the features you desire.

Step 3: Ensure you have, or can borrow the items

listed in the

Tools Required section of this guide.

If you ﬁnd that this installation is too difﬁcult to perform, please visit

the Professional Installer Network

section of the www.readyremote.

com web site or visit: www.proinstallation.com to contact one of

our 7,000 authorized retailers to have the product professionally

installed.

Caution! Failure to properly install this product may

result in costly damages, personal injury or both.

Important: This product, guide or other related material is subject

to change without notice, please check www.readyremote.com.

iv

What's Included

s Control Module (receiver)

s One 4- Button Remote Control

s One 18-pin Harnesses

s Control Button (Valet/Program Switch)

s LED status indicator

s This Guide

Tools Required

s Multimeter

s Drill

s 1/4 Drill Bit (for hood pin switch)

s Screwdrivers (Phillips and Flathead)

s Wire Stripper

s Solder Iron

s Electrical Tape

s Pliers

s Crimping Tool

s Safety Glasses

Note: The installation tools listed above may be optional. The re-

quired tools will vary depending on your vehicle.

v

Important Information

Government regulations

Read the Government Regulations sections of this

guide prior to operating this system.

Your warranty

Your system comes with a warranty. Your product warranty must

be validated following your purchase. You can validate online at:

www.prodregister.com/directed or complete and return the war-

ranty registration card.

Replacement remote controls

If additional remote controls are desired, please see your autho-

rized dealer or visit us at www.readyremote.com to order. Your

replacement part number is 7143R (4-button).

Installation guide

The installation guide included within is abbreviated. If more infor-

mation is required, please consult the expanded version which can

be found under

On-line Tech Support at www.readyremote.com.

vi

Guide translations

If you want a Spanish or French version of the Installation/Owners

Guide, please download it from www.readyremote.com and click

on On-Line Tech Support.

Estimado Cliente:

Si buscas los guías de instalación/del usario, por favor de bajar

lo del Soporte Técnico en-línea en el sitio www.readyremote.com

Cher consommateur:

Si vous désirez une version française ou espagnole du guide

d’utilisateur ou d’installation, veuillez s.v.p. le télécharger à

l’adresse suivante: www.readyremote.com en appuyant sur l’icône

<<On-line Tech Support>>.

1

Contents

Congratulations .........................................................................iii

STOP! Read this First ..................................................................iii

What's Included ......................................................................iv

Tools Required ...........................................................................iv

Important Information ..................................................................v

Your warranty ......................................................................v

Replacement remote controls ..................................................v

Installation guide ..................................................................v

Guide translations ...............................................................vi

Installation Guide ....................................................................... 3

Wiring schematic ................................................................ 3

Wiring Connections ................................................................... 4

Main Harness (H1), 18-pin connector .................................... 4

LED Plug-in Harness ............................................................. 5

Control button/valet switch .................................................. 5

Programming System Features ..................................................... 6

Feature Menu ............................................................................ 7

Menu 1 .............................................................................. 7

Remote Control Programming ...................................................... 8

Owner's Guide ....................................................................... 11

System maintenance .......................................................... 11

Battery replacement ........................................................... 11

Remote Control Functions .......................................................... 12

Standard configuration ....................................................... 12

Using the System .................................................................... 13

Locking ............................................................................ 13

Unlocking ......................................................................... 13

Disabling the system without a transmitter ............................. 14

Audible Mode ................................................................... 14

Valet Mode ....................................................................... 15

Panic Mode ...................................................................... 15

Rapid Resume Logic ................................................................. 16

Programming Options ............................................................... 16

Convenience expansion options .......................................... 17

Government Regulations ........................................................... 18

2

Patent Information .................................................................... 20

Lifetime Consumer Warranty ...................................................... 21

Installation Guide

Wiring schematic

21994

Top View

Front View

Back View

Control button/Valet switch

H1 Main Harness

LED Programming indicator

Antenna

4

Wiring Connections

Main Harness (H1), 18-pin connector

H1/1

RED/WHITE (-) CHANNEL 2 OUTPUT

H1/2

BROWN/BLACK UNLOCK #87 NORMALLY CLOSED

H1/3

ORANGE (-) 500mA GROUND-WHEN-LOCKED-

OUTPUT

H1/4

YELLOW (+) SWITCHED IGNITION INPUT

H1/5

WHITE/BLUE (-) 200mA CHANNEL 3 VALIDITY OUTPUT

H1/6

LT. GREEN/BLACK (-) 200mA FACTORY ALARM DISARM

OUTPUT

H1/7

BROWN (-) HORN HONK OUTPUT

H1/8

BLACK GROUND

H1/9

WHITE (+/-) PARKING LIGHTS FLASH OUTPUT

H1/10

VIOLET UNLOCK #87 NORMALLY OPEN

H1/11

BLUE/BLACK UNLOCK #30 COMMON OUTPUT

H1/12

VIOLET/BLACK LOCK#87 NORMALLY OPEN

H1/13

WHITE/BLACK LOCK #87 NORMALLY CLOSED

H1/14

GREEN/BLACK LOCK #30 COMMON OUTPUT

H1/15

BLACK/GREY DOMELIGHT RELAY #30 OUT

H1/16

BLACK/GREY-1 DOMELIGHT RELAY #87 IN

H1/17

BLUE (-) 200mA SECOND UNLOCK OUTPUT

H1/18

RED (+) 12V CONSTANT POWER INPUT

5

LED Plug-in Harness

1

BLUE INPUT

2

RED OUTPUT

Control button/valet switch

1

GREY INPUT

2

BLACK OUTPUT

6

Programming System Features

The System Features Learn Routine dictates how the unit operates. It

is possible to access and change most of the feature settings using

the Control button/valet switch. (see

Feature Menus)

1. Turn the ignition On, then off.

2. Within 15 seconds, Press and release the Control button/

valet switch the number of times corresponding to the feature

you want to program. (See Feature Menu section).

3. Press the button one more time and HOLD it, the horn honks

and the LED ﬂashes to indicate which feature number is

selected. For example, groups of 8 ﬂashes indicate feature

8 is selected.

4. While still holding the Control button/valet switch, use the

remote control to select the desired setting. As shipped the

remote control is conﬁgured to the LED On settings.

5. Press the

button to select LED On. The LED light solids and

the horn honks one time. Press the

button to change to

LED Off setting. The LED goes out to indicate the change, and

the horn honks twice.

The learn routine exits if any of the following occurs:

s The ignition is turned On

s There is no activity for 15 seconds

s The Control button/valet switch is pressed too many times

7

Feature Menu

Default settings are in bold type.

Menu 1

Feature # Feature LED ON LED OFF

1 Ignition controlled

door lock

ON

OFF

2 Ignition controlled door

unlock

ON

OFF

3 Ignition controlled

domelight

ON

OFF

4 Door Lock Output

Duration

0.8 sec

3.5 sec 0.4 sec

5 Unlock Output Pulse

count

Single

Double

6 Lock Output Pulse

Count

Single

Double

7 Comfort Closure*

OFF

ON

8 Code Hopping

ON

OFF

*Comfort Closure is not available on all vehicles types.

Visit www.readyremote.com for more information.

8

Remote Control Programming

The system comes with one remote control that has been taught to

the control module. The control module can store up to four different

remote control codes in memory.

1.

Turn key to the On position

2. Within 10 seconds,

press and release the Control button/

valet switch the number of times corresponding to the desired

channel as shown in the following table.

3. Once you have selected the channel, press the Control button

once more and HOLD it. The horn honks and the LED ﬂashes

to conﬁrm the selected channel. Do not release the Control

button.

4. While holding the Control button/valet switch, press the but-

ton on the remote to be assigned to the selected channel.

The horn honks indicating successful programming. It is not

possible to teach a remote control button to the system more

than once.

5. Once the code is learned, the Control button may be re-

leased.

9

Channel/ Function

Channel

#

Function Wire Color

1 Auto Learn

2 Lock Only

3 Unlock

Only

4 Channel 2 RED/WHITE

5 Channel 3

WHITE/BLUE

6 Lock/Unlock, Panic

7 Panic Only

8 Delete all remotes

Note: For Auto Learn Conﬁguration, see Owner's Guide section

Remote Control Functions

Channel 8: If any button from a remote is programmed to Channel

8, all remotes are erased from memory. System features revert to

the default settings.

This is useful if a remote is lost or stolen, all programming is erased

from memory. You are also able to start from scratch if the remote

buttons were programmed incorrectly.

10

The programming routine exits if any of the following

occurs:

s The ignition is turned off

s There is no activity for 15 seconds

s The Control button/valet switch is pressed too many times

11

Owner's Guide

System maintenance

The system requires no speciﬁc maintenance beyond battery re-

placement for the remote controls. Your remote is powered by a

coin cell battery (3V CR2032) that lasts approximately one year

under normal use. When the battery begins to weaken operating

range is reduced.

Battery replacement

Locate the small slot on the side of the remote control. Insert a small

slotted screwdriver or equivalent tool into slot and pry the case

apart. Replace battery while verifying the correct polarity and then

snap case together.

Remote Control Functions

The remote control buttons are used to send commands to the sys-

tem.

Standard conﬁguration

Lock: Press on the remote control.

Unlock: Press

on the remote control.

Panic: Press to activate panic mode.

Audible Mode: Press

to operate Audible mode

™

or an op-

tional auxiliary function.

s To receive conﬁrmation honks, press before locking

and unlocking.

s An optional auxiliary function such as trunk release may be

controlled by pressing and holding

for 2 seconds.

Channel 3 Auxiliary: Press and simultaneously to operate

an expansion option. See Convenience expansion options section.

13

Using the System

Locking

Pressing for one second locks the doors and activates the op-

tional Failsafe Starter Kill. (the starter kill prevents the starter from

cranking, when installed.) The horn will honk (If audible is turned

on by pressing

before you press ), and the parking lights

ﬂash one time to conﬁrm the system is locked.

The LED ﬂashes once per second continually while the system is

locked.

Pressing the

button again within 3 seconds of ﬁrst press acti-

vates Audible Mode for the single operation only.

Important: Manually locking the vehicle does not disable the

starter kill.

Unlocking

Pressing for one second unlocks the doors. The horn honks

twice - (If audible mode is turned on by pressing

before you

press ) - and the parking lights ﬂash twice to conﬁrm unlock-

ing of the system.

14

Disabling the system without a transmitter

If your remote transmitter is lost or damaged, you can manually

override the starter kill. You must have the vehicle's ignition key and

know where the Control button/Valet switch is located. For refer-

ence, you may want to note the location of the Control button/valet

switch in this guide.

To bypass the starter kill:

1. Turn the ignition On.

2. Press and release the Control button/valet switch within 10

seconds.

The status LED stops ﬂashing and the vehicle may be started.

If the vehicle does not start, you may have waited too long.

Turn the ignition off and repeat the process.

Control button/valet switch location: ______________________

Audible Mode

To temporarily turn on the lock or unlock horn honk(s), press

before locking or unlocking. The conﬁrmation honk(s) sound for the

single operation only.

Page is loading ...

Directed Electronics 21994 Owner's manual

This manual is also suitable for

Directed Electronics 21994 Owner's manual

Related papers

Other documents