Sigma BM60 DT Instruction book

Type
Instruction book
Via Artigianato 85 – 25030 Torbole Casaglia (BRESCIA) ITALY – Tel. 0302650479 – Fax 0302650143
INSTRUCTION BOOK
PLANETARY MIXER
BM60/80/100 DT
www.gk-nhl.ru
8(831) 273-97-50
CONTENTS
EXPLODED VIEW BM60-BM80-BM100 DT
Table 1
LIFTING BOWL GROUP
www.gk-nhl.ru
8(831) 273-97-50
EXPLODED VIEW BM60-BM80-BM100 DT
Table 2
www.gk-nhl.ru
8(831) 273-97-50
SPARE PARTS LIST FOR PLANETARY MIXER BM60-BM80-BM100 DT
N° RIF. N° CODE DESCRIPTION QUANTITY
01 25009096 START button + code 25009093 + 25009094 1
02 25009094 Lift/Descent push button + 25009093 + 25009043 2
03 25007039 Timer + Knob 25007038 1
04 13000319 Ball bearing 6208 2RS 40-80-18 3
05 13000317 Ball bearing 6206 2RS 30-62-16 3
06 01101022 Planetary shaft for reducer 1
07 01101073 Variator belt 41,5x12x1419 1
08 13000326 Ball bearing 6305 2RS 25-62-17 2
09 01101017 Return shaft 60 Hz 1
01101070 Return shaft 50 Hz 1
10 01101016 Drive pulley 1
11 01101013 Variable half pulley 2
12 01101012 Variable pulley shaft 1
13 01101083 Variator spring upper cover 1
14 01101084 Variator spring lower cover 1
15 08101014 Variable pulley spring 2
16 08000001 Shock absorber 588434 700N 1
17 03101057 Upper cover 1
18 11001301 Motor G100 4P 2,2 Kw 230-400V/3 B5R (BM60DT) 1
11001302 Motor G100 4P 3 Kw 230-400V/3 B5R (BM80DT) 1
11001302 Motor G100 4P 3 Kw 230-400V/3 B5R (BM100DT) 1
19 14002822 Small foot M16 98/6364 1
20 25001301 Microswitch + lever 25001302 2
21 01095028 Round microswitch 1
22 01098108 Bowl blocking handle 2
23 01101019 Planetary 1
24 04101120 Bowl BM60 DT 1
04101156 Bowl BM80 DT 1
04101212 Bowl BM100 DT 1
25 01101148 Sleeve 1
26 05101160 Protection grid 1
27 01101149 Anti-unlocking ring 1
28 01101080 Tool shaft 1
29 13000311 Ball bearing 6200 2RS 10-30-09 4
30 01101077 Toothed crown for planetary 50 Hz 1
01101079 Toothed crown for planetary 60 Hz 1
31 01101020 Planetary pinion 1
32 01101018 Toothed crown 1
33 25009027 Net Lamp 1
34 25009097 STOP button + code 25009093 + 25009047 1
35 01101043 Bowl supporting arm 1
36 13000016 Ball bearing 6205 2RS 25-52-15 2
37 01101100 Bowl lifting screw 1
38 11000501 Motor G71 4P 0,55 Kw 400V/3 50Hz B14 1
39 01106025 Motor pulley Q18 1
40 12003301 Toothed belt SPZ 512 2
www.gk-nhl.ru
8(831) 273-97-50
41 01101095 Lifting bowl pulley 1
42 01101096 Bowl lifting screw nut 1
43 13000315 Ball bearing 6204 2RS 20-47-17 1
44 01097047 Bevel gear pair for reducer 1
45 01101023 Bevel gear for reducer 1
46 01101009 Motor chair bars 2
47 01101181 Rack pole 1
48 01101040 Speed selecting lever 1
49 14002203 Knob 40M8 PB /41 1
50 01098041 Closure cover 1
51 01101179 Speed pin 1
52 08098055 Handle spring 1
53 01095065 Speed lever support 1
54 01101036 Toothed wheel 1
55 01095008 Motor chair 1
56 02047046 Micro square 1
57 01101066 Bowl blocking tube 1
58 25005120 Remote control switch LC1K0901B7 1
59 25005123 Remote control switch LC1K0601B7 2
60 25008006 Transformer 25VA 0/230/440 – 0/24 1
61 25001320 Microswitch MV15 1
62 01101044 Bowl lifting bars 2
63 01101076 HUDSON – MESA shaft 1
64 01097078 Reducer support HUDSON – MESA 1
65 31000001 Closure handwheel HUDSON – MESA 1
66 01097079 Closure cap 1
LIST OF RECOMMENDED SPARE PARTS FOR BM60-BM80-
BM100DT
(2 YEARS OPERATION)
N° RIF. N° CODE DESCRIPTION QUANTITY
01 25009096 START button + code 25009093 + 25009094 1
02 25009094 Lift/Descent push button + 25009093 + 25009043 2
03 25007039 Timer + Knob 25007038 1
04 13000319 Ball bearing 6208 2RS 40-80-18 3
05 13000017 Ball bearing 6206 2RS 30-62-16 3
07 01101073 Variator belt 41,5x12x1419 1
08 13000326 Ball bearing 6305 2RS 25-62-17 2
20 25001301 Microswitch +lever 25001302 2
58 25005120 Remote control switch LC1K0901B7 1
59 25005123 Remote control switch LC1K0601B7 2
60 25008006 Transformer 25VA 0/230/440 – 0/24 1
61 25001320 Microswitch MV15 1
www.gk-nhl.ru
8(831) 273-97-50
CONTROL PANEL
USE AND PROGRAMMING OF THE CONTROL PANEL
Selection of automatic/manual mode
Press the correspondent button (only when the mixer is not working).
In manual mode the display of the program will show “ - “
Timer/speed/temperature selection
Press various times the correspondent button till the desired selection.
PROGRAM
THERMIC ALARM OR EMERGENCY
OPEN GRID ALARM
MANUAL/ AUTOMATIC SELECTION
SPEED SELECTION
TIMER
SPEED
TEMPERATURE
BOWL LIFTING
BOWL LOWERING
EMERGENCY
www.gk-nhl.ru
8(831) 273-97-50
After a minute the display will go automatically on the timer selection (default)
Speed selection
Press the speed button correspondent to the desired value (1 – 6) or the buttons “ + “ and “ – “
Time selection
Keep pressed the buttons “ + “ o “ – “ that are below the display of the timer till the desired value.
Programming mode
You can store 10 programs with 8 different cycles. To start the programming mode:
1) Select the manual or automatic mode
2) Keep pressed for 3 seconds both buttons + and that are below the display (display program = 1
blinking)
3) Select with the button “ + “ or “ – “ the desired program.
4) Select the speed button correspondent to the desired value for the first cycle (1 6)
5) Select the desired time for the first cycle
6) Press the “ START “ button to store the first cycle. As confirmation there will appear “MEM”
7) Press the STOP button if you wish to ultimate the programming or repeat the points 4, 5, 6 to store the other
cycles.
Start the mixer
In manual mode:
- Press the START button. If there are no impediments ( open grid, bowl not in position…) the mixer will
start its cycle of work till the depletion of the memorized time. Pressing the STOP “ button the mixer will
stop the cycle; pressing it again the mixer will set again the time initially memorized.
In automatic mode:
- Select the desired program and press the START button. If there are no impediments ( open grid, bowl
not in position…) and the program is valid the mixer will start its cycle of work till the depletion of the
memorized time (NOTICE: a no-valid program will be signalled by the indication “ E E E E “ on the display
of the timer). Pressing the “ STOP “ button the mixer will stop the cycle; pressing it again the mixer will start
the cycle from the beginning.
Lower the bowl
Keep pressed the button “ bowl descent “. If the mixer is working it will be stopped and then once it is completely still
(speed = 0 ), the bowl will lower.
General information
During the programming both leds “ automatic “ and “ manual “ will light.
During the functioning it is no more possible to change the automatic/manual selection.
During the functioning it is possible to change speed and time, but this value will not be stored.
www.gk-nhl.ru
8(831) 273-97-50
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Sigma BM60 DT Instruction book

Type
Instruction book

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages