DF908
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
(888) 258-0533
The DF908 consists of the DF910 Lat
Machine and the DF935 Stack Kit
LAT PULLDOWN MACHINE
WITH 200 LB WEIGHT STACK
Assembly Manual
BOX CONTENTS
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
REAR SUPPORT
QTY 1
A
FRONT SUPPORT
QTY 1
B
BOTTOM FRAME
QTY 1
C
REVOLVING CHROME
ROW BAR
QTY 1
D
LAT CABLE
QTY 2
E
FOOT PLATE
QTY 1
C1
FOOT REST
QTY 1
C2
LAT BAR
QTY 1
F
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
BOX CONTENTS
SEAT SUPPORT
QTY 1
J
SEAT BRACKET
QTY 1
I
UPPER PULLEY
FRAME
QTY 1
G
SEAT PAD
QTY 1
H
REAR CROSSMEMBER
QTY 1
N
HOLD-DOWN SUPPORT
QTY 1
M
HOLD-DOWN
TUBE
L
ROLLER PAD
QTY 2
P
FLANGE
QTY 2
Q
BOTTOM PULLEY
FRAME
QTY 1
R
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
(888) 258-0533
HARDWARE
S
MUSHROOM CAP
QTY 2
4-1/2” PULLEY
QTY 3
U
3-1/2” PULLEY
QTY 3
PULLEY BUSHING
QTY 4
SNAP HOOK
QTY 6
CHAIN
QTY 2
M12 x 70MM BOLT
QTY 2
AA
M10 x 45MM BOLT
QTY 4
DD
EE
M10 x 20MM BOLT
QTY 2
FF
M10 x 70MM
FLAT HEAD BOLT
QTY 3
RUBBER SHOE
QTY 2
T
V
W
X
Y
M12 x 65MM BOLT
QTY 2
BB
M10 x 70MM BOLT
QTY 3
CC
GG
M10 x 65MM
CARRIAGE BOLT
QTY 9
HARDWARE
KK
M10 LOCKNUT
QTY 19
M12 WASHER
QTY 8
HH
M10 WASHER
QTY 20
I I
JJ
M12 LOCKNUT
QTY 4
(SEE INSET) ASSEMBLE THE 4 ½” PULLEY (U) INTO THE BOTTOM PULLEY FRAME
(R) USING THE M10 x 45MM BOLT (DD), M10 WASHERS (II), AND M10 LOCKNUT
(KK).
INSTALL TO BOTTOM FRAME (C) USING THE M10 x 65MM CARRIAGE BOLTS (GG),
M10 WASHERS (II), AND M10 LOCKNUTS (KK).
ATTACH THE REAT CROSSMEMBER (N) TO THE BOTTOM FRAME (C) USING THE
M12 x 70MM BOLTS (AA), M12 WASHERS (HH), AND M12 LOCKNUTS (JJ). INSTALL
THE RUBBER BOOTS (T) OVER THE ENDS OF THE CROSSMEMBER.
ATTACH THE FOOT PLATE (C2) AND FOOT REST (C1) TO THE BOTTOM FRAME (C)
USING M10 x 70 MM FLAT HEAD BOLTS (FF), M10 WASHERS (II), AND M10 LOCK-
NUTS (KK).
BOTTOM FRAME ASSEMBLY
TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET
Some components may be pre-installed
from the factory
(NOTE: THE NUTS USED ON THIS
BENCH ARE LOCK NUTS, THIS MEANS
YOU MUST TIGHTEN THEM DOWN
PAST THE PLASTIC INSERT.)
U
DD
I I
I I
R
KK
AA
N
HH
HH
T
T
C
I I
KK
JJ
GG
I I
KK
I I
KK
C2
C2
FF
ATTACH THE SEAT PAD (H) TO THE SEAT BRACKET (I) USING THE M10 x 20MM
BOLTS (EE) AND M10 FLAT WASHERS (II). THEN SLIDE THE SEAT BRACKET (I)
INTO THE SEAT SUPPORT (J).
(WAIT TO COMPLETE THE FOLLOWING STEP UNTIL THE CABLES ARE INSTALLED)
INSTALL THE 4 ½” PULLEY (U) INTO THE SEAT SUPPORT TUBE (J) USING THE
M10 x 45MM BOLT (DD) , M10 WASHERS (II), AND M10 LOCK NUT (KK).
SEAT FRAME ASSEMBLY
H
I
FF
I I
J
V
DD
I I
I I
KK
SLIDE THE HOLD-DOWN TUBE (L) INTO THE HOLD-DOWN SUPPORT (M) . LOCK
INTO PLACE WITH PULL-PIN.
SLIDE THE ROLLER PADS (P) OVER THE LEG PAD TUBE AND INSERT THE MUSH-
ROOM CAPS (S). TAP INTO PLACE WITH ARUBBER HAMMER.
LEG HOLD DOWN ASSEMBLY
L
M
S
P
S
P
FLOATING PULLEYASSEMBLY
ASSEMBLE THE FLOATING PULLEY ASSEMBLY BY USING 4-1/2” PULLEYS (U),
FLANGES (Q), M10 x 45MM BOLTS (DD), M10 WASHERS (II), AND M10 LOCKNUTS (KK).
I I
I I
KK
Q
EE
U
UPPER PULLEY FRAME ASSEMBLY
INSTALL THE FRONT 3-1/2” PULLY (V) USING THE M10 x 70MM BOLT (CC), PULLEY
BUSHINGS (W), AND M10 LOCKNUT (KK). REPEAT FOR REAR PULLEYS.
KK
W
W
V
CC
G
CC
V
W
KK
W
NEXT ASSEMBLE THE UPPER PULLEY FRAME ASSEMBLY ONTO THE FRONT AND
BACK SUPPORTS (A,B) USING THE M12 x 65MM BOLTS(BB), M12 WASHERS (HH), AND
M12 LOCKNUTS (JJ).
MAIN FRAME ASSEMBLY
B
A
HH
JJ
HH
BB
JJ
HH
HH
BB
LAY THE BOTTOM FRAMEASSEMBLY ON ITS SIDE. ATTACH THE MAIN FRAME
ASSEMBLY, THE LEG HOLDDOWN ASSEMBLY, AND THE SEAT FRAME ASSEMBLY
USING THE M10 x 65MM CARRIAGE BOLTS (GG), M10 WASHERS (II), AND M10
LOCKNUTS (KK).
FINALASSEMBLY
BOTTOM FRAME ASSY
MAIN FRAME ASSY
LEG HOLDDOWN ASSY
SEAT FRAME ASSY
DD
I I
KK
I I
KK
KK
KK
KK
I I
I I
I I
I I
I I
KK
KK
ASSEMBLY INSTRUCTIONS FOR
THE DF935 STACK KIT
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
(888) 258-0533
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
BOTTOM SUPPORT
QTY 1
A
UPPER PULLEY
FRAME
QTY 1
B
DF935 WEIGHT STACK
BOX CONTENTS
CHROME RODS
QTY 2
C
WEIGHT STACK
(19) 10 LB. PLATES
QTY 1
D
WEIGHT STACK
TOP PLATE
QTY 1
F
SELECTOR ROD
QTY 1
E
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
(888) 258-0533
RUBBER SHOE
QTY 3
G
DF935 WEIGHT STACK
HARDWARE
M10 x 75MM BOLT
QTY 2
H
RUBBER DOUGHNUTS
QTY 2
M
M10 WASHER
QTY 4
I
M10 LOCKNUT
QTY 2
J
WEIGHT STACK
ADJUSTMENT PIN
QTY 1
L
M10 x 25MM BOLT
QTY 2
K
WEIGHT STACK
CABLE CONNECTOR
QTY 1
N
SPRING PIN
QTY 1
O
PULLEY
QTY 1
P
PULLEY BUSHING
QTY 2
Q
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
(888) 258-0533
RUBBER SHOE
QTY 3
G
DF935 WEIGHT STACK
HARDWARE
M10 x 75MM BOLT
QTY 2
H
RUBBER DOUGHNUTS
QTY 2
M
M10 WASHER
QTY 4
I
M10 LOCKNUT
QTY 2
J
WEIGHT STACK
ADJUSTMENT PIN
QTY 1
L
M10 x 25MM BOLT
QTY 2
K
WEIGHT STACK
CABLE CONNECTOR
QTY 1
N
SPRING PIN
QTY 1
O
PULLEY
QTY 1
P
PULLEY BUSHING
QTY 2
Q
UPPER PULLEYASSEMBLY
INSTALL THE PULLEY (P) INTO THE UPPER PULLEY FRAME (B), USING M10 x
75MM BOLT (H), PULLEY BUSHINGS (Q), AND M10 LOCKNUT (J).
J
Q
P
Q
H
B
SCREW WEIGHT STACK CONNECTOR (N)
INTO TOP OF WEIGHT STACK ROD AND
TIGHTEN WITH WRENCH.
F
O
E
INSERT WEIGHT STACK ROD (E) INTO CENTER HOLE OF
TOP PLATE (F) ALIGNING TOP HOLE OF WEIGHT STACK
ROD WITH SPRING PIN HOLE. INSERT SPRING PIN (O)
AND TAP WITH HAMMER UNTIL FLUSH WITH SURFACE.
N
WEIGHT STACK ASSEMBLY
LOWER FRAME ASSEMBLY
B
INSTALL THE RUBBER CAPS (G) ONTO THE BOTTOM SUPPORT (B). ATTACH THE BOTTOM
SUPPORT (B) TO THE LAT MACHINE USING THE M10 x 75MM BOLTS (H), M10 WASHERS (I), AND
M10 LOCKNUTS (J).
G
I
I
B
J
I
G
I H
WEIGHT STACK ASSEMBLY
INSTALL THE RUBBER DOUGHNUTS (L) ONTO THE BOTTOM OF THE CHROME RODS (C) ,
LEAVING APPROXIMATELY 2” PROTRUDING. INSERT THE CHROME RODS INTO THE TWO
OUTER HOLES IN THE BOTTOM SUPPORT.
ASSEMBLE THE WEIGHT STACK (E) BY SLIDING EACH PLATE OVER THE CHROME RODS (C)
AND ON TO THE BOTTOM SUPPORT.
SLIDE THE SELECTOR ROD/TOP PLATE ASSEMBLY OVER THE CHROME RODS (C) AND
THROUGH THE WEIGHT STACK (E). INSERT THE WEIGHT STACK ADJUSTMENT PIN (K) INTO
THE WEIGHT STACK (E).
L
C
E
K
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
